Skip to main content

Trucking Mind

One load at a time. This calculator runs one paper roll load against 49 CFR 393.122. A result that says Not allowed means the load must not roll in that pattern. A result that says Required names the securement to add first.

Enter the roll size and weight, pick the eye orientation and the vehicle, then answer the questions for that load. Every answer updates as you change each field.

The rolls

Roll width is the length of the roll along its axis: the height of a roll standing on its end. Diameter is the width across the round face.

The vehicle and the load

Eyes vertical: tipping and voids

Measure the open space behind the group of rolls, including the space at the rear of the vehicle.

Eyes crosswise: rolling and side space

Add the space at both ends of a roll or row of rolls: the total gap between the roll ends and the walls.

Eyes lengthwise: movement in each direction

Flatbed and curtain-sided tiedowns

Pattern meets 49 CFR 393.122

The answers meet the paper roll rules in 49 CFR 393.122.

CheckResultDetail
ScopePassThe shipment weighs 10,000 lb. Section 393.122 applies at 5,000 lb or more, so the paper roll rules govern this load.
Tight placementPassThe rolls sit tightly against the walls of the vehicle, other rolls, or other cargo (49 CFR 393.122(b)(1)).
Rear voidPassThe void behind the group is 0 in, no more than the 40 in roll diameter (49 CFR 393.122(b)(3)).
Sideways tippingPassVehicle structure or other cargo prevents the rolls from tipping or falling sideways or rearwards (49 CFR 393.122(b)(4)(i)).
Forward tippingPassVehicle structure or other cargo prevents the forwardmost roll from tipping or falling forwards (49 CFR 393.122(b)(4)).

The figures

FigureValueNote
Shipment weight10,000 lbSection 393.122 applies at 5,000 lb or more
Width to diameter ratio1.5Above 1.25: the forward tipping rule can trigger without a friction mat
Anti-tip thresholds50 in / 70 in / 80 in1.25x, 1.75x and 2x the 40 in diameter
Rear void vs diameter0 inDiameter 40 in. A void over the diameter needs rearward restraint.

What to do

  • Inspect the cargo and the securement devices within the first 50 miles and adjust as needed (49 CFR 392.9).

Notes

  • Commodity rules take precedence over the general cargo rules. Where 49 CFR 393.122 and the general rules in 49 CFR 393.100 through 393.114 differ, the paper roll rules govern.
  • A damaged tiedown is a violation, not an out-of-service defect. It does not count toward the tiedown count or the aggregate working load limit, so replace it before you roll.

This checker applies 49 CFR 393.122 to your answers. Confirm the measurements with a tape before you rely on a result.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.

Quick answer: Paper rolls that weigh 5,000 lb or more, alone or together, follow the securement rules in 49 CFR 393.122. Eyes-vertical rolls tip when the width passes 1.25, 1.75, or 2 times the diameter. Each ratio triggers its own rule. Stacked eyes-vertical loads are prohibited on a flatbed or in a curtain-sided vehicle. This calculator runs one load through every rule in the section and names the pattern the load needs.

Last reviewed: · Focus keyword: paper roll securement

What does 49 CFR 393.122 cover?

Section 393.122 is the commodity rule for paper rolls in Part 393, Subpart I. It applies to shipments of paper rolls that weigh 2,268 kg (5,000 lb) or more, individually or together. A single 6,000 lb roll is covered. So is a group of four 1,500 lb rolls. The weight that counts is the shipment weight, not the weight of one roll.

Two kinds of load may choose. A shipment under 5,000 lb and paper rolls unitized on a pallet may follow the paper roll rules or the general cargo rules in sections 393.100 through 393.114. The carrier makes the choice. This calculator follows the paper roll rules either way, because they are the clearest standard for the load.

The section works by eye orientation and vehicle type. The eye is the hole through the center of the roll. A roll standing on its end has its eye vertical. A roll lying with its axis across the trailer has its eye crosswise. A roll lying with its axis along the trailer has its eye lengthwise.

Each orientation gets its own paragraph. Each paragraph has its own stacking rules.

Commodity rules take precedence over the general rules. Where section 393.122 and the general rules differ, the paper roll rules govern. The general rules still matter on a flatbed or in a curtain-sided vehicle, where tiedowns must meet sections 393.100 through 393.114 on top of the paper roll pattern.

Eye orientationSided vehicleStackedFlatbed or curtain-sided
VerticalParagraph (b): tight placement, void rules, tipping ratiosParagraph (d): lower layer to the front, blocking roll rulesSided-vehicle pattern plus tiedowns. Stacking prohibited.
CrosswiseParagraph (e): anti-roll, chocks, rear-door ban, 8 in side spaceParagraph (f): wells, upper-layer forward and rear rulesAnti-roll and chock rules plus tiedowns against lateral movement.
LengthwiseParagraph (g): forward, rearward and lateral meansParagraph (h): lower layer full first, upper layer in the wellsSided-vehicle pattern plus tiedowns.

How do paper rolls tip?

A paper roll standing on its end is a cylinder balanced on a round edge. Braking throws its weight forward. A sharp turn throws it sideways. A tall narrow roll tips more easily than a short wide one. The rule measures that risk with one ratio: roll width divided by roll diameter.

Width means the length of the roll along its axis. For a roll standing on its end, width is the height of the roll. Diameter is the width across the round face. A roll 60 in wide and 40 in across has a ratio of 1.5. A roll 80 in wide and 40 in across has a ratio of 2.0. The calculator shows the ratio for the load you enter.

Tipping is the main failure for eyes-vertical rolls. A roll that tips forward can break through the front of the trailer or crush the cargo ahead of it. A roll that tips sideways can push through a trailer wall. The ratios in the next section mark the points where the rule demands extra securement.

What do the 1.25, 1.75 and 2 times ratios mean?

The rule sets three ratio lines in paragraph (b)(4). Each line answers a different question. The 2 times line covers sideways and rearward tipping. The 1.75 times line covers the forwardmost roll tipping forwards. The 1.25 times line covers forward tipping for any roll that friction mats alone do not restrain.

At more than 2 times the diameter, a roll that vehicle structure or other cargo does not stop from tipping sideways or rearwards must be prevented from tipping by banding it to other rolls, bracing, or tiedowns. At exactly 2 times the diameter the rule does not trigger: the text says more than 2 times.

The forwardmost roll gets the tightest line. At more than 1.75 times the diameter, it must be prevented from tipping forwards by banding, bracing, or tiedowns unless vehicle structure or other cargo already stops it. Friction mats alone do not excuse a roll past 1.75: the mat exception only reaches 1.75.

Between 1.25 and 1.75 times the diameter, the forward rule turns on the friction mat. A roll in that band that friction mats alone restrain against forward movement needs no banding, bracing, or tiedowns to prevent forward tipping. The same roll without that mat restraint needs banding, bracing, or tiedowns. At 1.25 times or less, no forward tipping rule triggers.

Width to diameter ratioWhat the rule asksWhat the load needs
More than 2.00Is the roll stopped from tipping sideways or rearwards?Banding, bracing, or tiedowns when nothing stops it.
More than 1.75Is the forwardmost roll stopped from tipping forwards?Banding, bracing, or tiedowns when nothing stops it.
More than 1.25 up to 1.75Do friction mats alone restrain forward movement?Nothing extra when mats alone restrain it. Banding, bracing, or tiedowns when they do not.
1.25 or lessNothing: no tipping ratio triggers.The placement and void rules still apply.

How do you secure paper rolls with the eyes vertical?

Start with placement. Rolls must sit tightly against the walls of the vehicle, other paper rolls, or other cargo. A tight group cannot start moving. A group that cannot start moving cannot build the momentum that breaks securement.

When the shipment has too few rolls to reach the walls, lateral movement must be prevented by filling the void, blocking, bracing, tiedowns, or friction mats. The rolls may also be banded together. Banded rolls must sit tightly against each other to form a stable group, with the bands applied tightly and secured so they cannot fall off the rolls or to the deck.

The rear void has its own test. When any void behind a group of rolls, including the space at the rear of the vehicle, exceeds the roll diameter, rearward movement must be prevented by friction mats, blocking, bracing, tiedowns, or banding to other rolls. A 40 in roll tolerates a void up to 40 in. Past that, the group needs restraint.

Split loads follow paragraph (c). If a roll in a split load is not prevented from forward movement by vehicle structure or other cargo, it must be prevented by filling the open space, or by blocking, bracing, tiedowns, friction mats, or some combination of these. A split load is two or more groups with open space between them. Each group needs its own forward restraint.

Then run the tipping ratios from the section above. The calculator checks each ratio against your answers for vehicle structure, other cargo and friction mats. It names the banding, bracing, or tiedowns the load needs.

Can you stack paper rolls?

Sometimes. The answer depends on the eye orientation and the vehicle. In a sided vehicle, eyes-vertical rolls may stack only when the lower layer extends to the front of the vehicle. The same front rule governs a second layer of eyes-crosswise rolls. Eyes-lengthwise rolls may not go into a higher layer at all if another roll will fit in the layer beneath.

On a flatbed vehicle or in a curtain-sided vehicle, stacked loads of paper rolls with eyes vertical are prohibited outright. There is no exception for a short stack or a light roll. Load eyes-vertical rolls in a single layer on a flatbed. Use the tiedowns the general rules require.

Eyes-vertical stacking has two more rules. Rolls in the second and later layers must be prevented from forward, rearward, or lateral movement by the means allowed for the bottom layer, or by a blocking roll from a lower layer. The blocking roll must be at least 1.5 in taller than the other rolls, or raised at least 1.5 in on dunnage.

Dunnage has a trap. A roll in the rearmost row of any layer raised using dunnage may not be secured by friction mats alone. A load that leans on mats for its principal securement needs banding, blocking, or tiedowns for that rearmost row. The calculator flags the combination when it appears.

Eyes-crosswise stacking runs on wells. No third or higher layer goes on unless all wells in the layer beneath are filled. The foremost roll in each upper layer, or any roll with an empty well in front of it, must be secured against forward movement by banding it to other rolls, by blocking against an adequately secured eye-vertical blocking roll at least 1.5 times taller than the diameter of the roll being blocked, or by placing it in a well formed by two lower rolls with a diameter equal to or greater than its own.

The rearmost roll in each upper layer needs banding when it sits in either of the last two wells formed by the rearmost rolls in the layer below. Eyes-lengthwise upper layers must sit in the wells formed by the rolls beneath. Each upper roll must be secured against forward and rearward movement by the bottom-layer means, a blocking roll, or banding.

Bundled lumber stacks under a parallel set of tier rules. The Lumber and Building Products Securement Calculator runs the multi-tier rules in 49 CFR 393.118 for lumber and building products.

Concrete pipe stacks in tiers with its own blocking rules. The Concrete Pipe Securement Calculator runs the pipe rules in 49 CFR 393.124.

How do you secure paper rolls with the eyes crosswise?

A roll lying across the trailer wants to roll. Paragraph (e) starts there: the rolls must be prevented from rolling or shifting longitudinally by contact with vehicle structure or other cargo, by chocks, wedges, or blocking and bracing of adequate size, or by tiedowns.

Chocks, wedges, or blocking must be held securely in place by some means in addition to friction, so they cannot become unintentionally unfastened or loose while the vehicle is in transit. Friction alone is not enough. Fix the chocks to the deck or against vehicle structure so road vibration cannot work them loose.

Never use the rear doors. The rearmost roll must not be secured using the rear doors of the vehicle or intermodal container, or by blocking held in place by those doors. Doors are not securement. A load that leans on the doors fails inspection and risks a roll on the ground when the doors open.

The side space test is 8 in in total. When the space between the ends of a roll or a row of rolls and the walls adds up to more than 8 in, void fillers, blocking, bracing, friction mats, or tiedowns must be used to prevent the roll from shifting toward either wall. Measure both ends and add them: 5 in on one side and 4 in on the other is 9 in in total.

The same 8 in rule reaches the upper layers of a stacked crosswise load. Rolls in an upper layer must be secured against lateral movement by the same means allowed for the bottom layer when the total side space passes 8 in.

Metal coils load by eye orientation too, with a different rule for each orientation. The Metal Coil Securement Calculator runs the coil rules in 49 CFR 393.120.

How do you secure paper rolls with the eyes lengthwise?

A roll lying along the trailer needs restraint in three directions. Paragraph (g) names a means for each one. Forward movement is stopped by contact with vehicle structure, other cargo, blocking, or tiedowns. Rearward movement is stopped by contact with other cargo, blocking, friction mats, or tiedowns. Rolling or lateral shifting is stopped by contact with the wall of the vehicle or other cargo, or by chocks, wedges, or blocking of adequate size.

Note the asymmetry. Friction mats appear in the rearward list and not in the forward list. A mat under the roll helps against rearward movement. Forward movement needs contact, blocking, or tiedowns.

Chocks, wedges, or blocking must be held in place by some means in addition to friction, the same rule as for eyes-crosswise loads. A chock that can vibrate loose is not securement.

Stacked eyes-lengthwise loads follow paragraph (h). No higher layer goes on if another roll will fit in the layer beneath. The upper layer must sit in the wells formed by the rolls beneath. Each upper roll must be secured against forward and rearward movement by any of the means allowed for the bottom layer, by use of a blocking roll, or by banding to other rolls.

What changes on a flatbed or curtain-sided vehicle?

Two things change. Both add work. First, the paper roll pattern from the sided-vehicle paragraphs still applies: eyes-vertical and eyes-lengthwise rolls must be loaded and secured as described for a sided vehicle. Second, the entire load must be secured by tiedowns in accordance with sections 393.100 through 393.114.

The tiedown count comes from section 393.110. An article that is not blocked against forward movement needs 1 tiedown at 5 ft or less and 1,100 lb or less. It needs 2 tiedowns at 5 ft or less over 1,100 lb, or over 5 ft up to 10 ft. Past 10 ft it needs 2 tiedowns plus 1 more for every 10 ft or part of 10 ft past the first 10 ft. A load blocked against forward movement by a headerboard, bulkhead, or other secured cargo needs 1 tiedown per 10 ft or part of 10 ft.

The count is only half the test. Section 393.106(d) requires the aggregate working load limit of the tiedowns to be at least half the weight of the article or group of articles. A load can pass the count and fail the strength test, or pass the strength test and fail the count. Both tests must pass. The calculator shows both numbers for the load you enter.

Logs are the one commodity with a lighter aggregate working load limit: one sixth of the stack weight under 49 CFR 393.116. The Log Securement Calculator runs the log rules.

For eyes-crosswise rolls on a flatbed, tiedowns must be used in accordance with sections 393.100 through 393.114 to prevent lateral movement. The anti-roll and chock rules from the sided-vehicle paragraph apply in full. The rear-door ban has no flatbed equivalent: there are no doors to lean on.

The flatbed ban matters most. Stacked eyes-vertical loads are prohibited on a flatbed or in a curtain-sided vehicle. No tiedown count cures it. If the load needs a second layer, it needs a sided vehicle.

For the working load limit of each tiedown, use the marked rating on the device. Unmarked tiedowns fall back to the default tables in 49 CFR 393.108. The Flatbed Calculator carries the full tiedown working load limit tables and the general cargo securement rules for every vehicle type.

A damaged tiedown is a violation, not an out-of-service defect. It does not count toward the tiedown count or the aggregate working load limit. Replace it before you roll. The Pre-Trip Inspection Checklist carries the cargo securement checks for the walkaround.

When does a friction mat count as securement?

A friction mat is a high-friction sheet placed under or against cargo to raise the grip between the load and the deck. The paper roll rules name friction mats as a permitted means in several places: lateral restraint for eyes-vertical rolls, rearward restraint behind a group, rearward restraint for eyes-lengthwise rolls and side-space restraint for eyes-crosswise rolls.

The mat earns its biggest role in the forward tipping rule. A forwardmost roll between 1.25 and 1.75 times its diameter that friction mats alone restrain against forward movement needs no banding, bracing, or tiedowns to prevent forward tipping. Past 1.75 times the diameter, the mat exception ends and the roll needs banding, bracing, or tiedowns whatever sits under it.

A mat that provides the principal securement for a paper roll must protrude from beneath the roll in the direction in which it provides that securement. A mat hidden fully under the roll does not meet the rule. The protrusion is the visible proof that the mat is placed to resist movement in that direction.

Mats have limits. A roll in the rearmost row of any layer raised using dunnage may not be secured by friction mats alone. Mats do not appear in the forward list for eyes-lengthwise rolls. Treat a mat as one means among several. Confirm the rest of the pattern covers the directions the mat does not.

How do you use the Paper Roll Securement Calculator?

  1. Enter the roll weight, the number of rolls, the roll diameter and the roll width. The calculator works out the shipment weight and the width to diameter ratio.
  2. Pick the eye orientation: vertical, crosswise, or lengthwise. Pick the vehicle type and the number of layers.
  3. Answer the questions for the orientation you picked: voids, friction mats, what stops the rolls moving and how the upper layers are held.
  4. Read the verdict, the check table, the figures and the notes. A Required result names the securement to add. A Not allowed result names a rule the load breaks.
  5. On a flatbed or curtain-sided vehicle, read the minimum tiedown count and the aggregate working load limit the load needs.
  6. Copy the summary for the trip records, or reset the calculator to start over.

Frequently asked questions

How many tiedowns does a paper roll load need on a flatbed?

The count comes from 49 CFR 393.110. A load 5 ft or shorter and 1,100 lb or lighter needs 1 tiedown. A load 5 ft or shorter and heavier than 1,100 lb needs 2 tiedowns, as does a load longer than 5 ft up to 10 ft whatever it weighs. Past 10 ft, add 1 tiedown for every 10 ft or part of 10 ft beyond the first 10 ft. A load blocked against forward movement needs 1 tiedown per 10 ft. The aggregate working load limit must also reach half the load weight under 49 CFR 393.106(d).

Can paper rolls be stacked on a flatbed?

No, not with the eyes vertical. Section 393.122(i)(1)(ii) prohibits stacked loads of paper rolls with eyes vertical on a flatbed vehicle or in a curtain-sided vehicle. Load eyes-vertical rolls in a single layer on a flatbed. In a sided vehicle, stacking is allowed when the lower layer extends to the front of the vehicle.

What is the 5,000 pound rule for paper rolls?

Section 393.122 applies to shipments of paper rolls that weigh 5,000 lb or more, individually or together. A shipment under 5,000 lb may follow the paper roll rules or the general cargo rules in 49 CFR 393.100 through 393.114. Paper rolls unitized on a pallet have the same choice.

How wide can a paper roll be before it needs anti-tip securement?

For a roll standing on its end, the lines are set by the ratio of width to diameter. Past 2 times the diameter, the roll needs banding, bracing, or tiedowns against sideways tipping. The forwardmost roll needs the same past 1.75 times the diameter. Past 1.25 times the diameter it needs the same when friction mats alone do not restrain it. Vehicle structure or other cargo that already stops the tipping removes the need.

Can the rear doors of a trailer hold a paper roll in place?

No. Section 393.122(e)(3) says the rearmost roll must not be secured using the rear doors of the vehicle or intermodal container, or by blocking held in place by those doors. Secure the rearmost roll with contact, chocks, wedges, blocking and bracing, or tiedowns.

Do friction mats count as securement for paper rolls?

Yes, in several places: lateral and rearward restraint for eyes-vertical rolls, rearward restraint for eyes-lengthwise rolls and side-space restraint for eyes-crosswise rolls. A friction mat that provides the principal securement must protrude from beneath the roll in the direction of securement. A roll in the rearmost row of a dunnage-raised layer may not be secured by friction mats alone.

Related tools

Sources

Follow on WhatsApp Ask by Voice