One group of pipe at a time. This calculator runs one group of concrete pipe, pipe of one diameter loaded together, against 49 CFR 393.124. A result that needs work means the load must not roll until each failed item is fixed.
Describe the vehicle, the pipe, the load arrangement and the tiedowns. Every answer updates as you change each field.
The vehicle and the pipe
Pipe in a sided vehicle or container falls under the general rules in sections 393.100 through 393.114, not under section 393.124. Pipe bundled tightly into a single rigid article with no tendency to roll is treated the same way.
The 45 inch line is measured on inside diameter. Pipe up to 45 inches follows paragraph (e). Pipe over 45 inches follows paragraph (f).
The load arrangement
Bell pipe
Blocking and immobilization
For pipe up to 45 inches, the bottom tier must be immobilized longitudinally at each end. For pipe over 45 inches, the front pipe and the rear pipe must be immobilized.
Tiedowns
Count every tiedown on the group, including longitudinal tiedowns. A damaged tiedown does not count: it is a violation and it adds nothing to the tiedown count or to the aggregate working load limit.
Securement plan checks out
Every check passes for this load under 49 CFR 393.124.
| Check | Result | Detail |
|---|---|---|
| Rule that applies | Pass | Concrete pipe on a flatbed trailer. Section 393.124 applies, paragraph (e), pipe up to 45 in inside diameter. |
| Aggregate working load limit | Pass | Provided aggregate WLL 39,600 lb meets the required 8,000 lb, half the group weight of 16,000 lb (section 393.124(b)(1)). |
| Tiedown count | Pass | 6 tiedowns on the group meet the required 4 for this pattern. |
| Tiedown pattern | Pass | One 1/2-in chain or wire rope runs longitudinally over the group, with 2 transverse tiedowns, one per 10 ft of a 20 ft load. Transverse tiedowns may pass through a pipe or over both longitudinal tiedowns between two pipes on the top tier (section 393.124(e)(2)(ii)). |
| Blocking | Pass | Timber blocking measures at least 4 by 6 in, is placed symmetrically about the center of each pipe, firmly against the pipe and secured against moving out (section 393.124(c)). |
| Tiering and wells | Pass | One tier. The bottom tier covers the full length of the vehicle (section 393.124(d)(2)). |
| Bell pipe | Info | Not bell pipe. The bell pipe rules in section 393.124(d)(5) do not apply. |
| End immobilization | Pass | The bottom tier is immobilized longitudinally at each end (section 393.124(e)(1)(i)). |
| Diameter grouping | Info | One pipe diameter in this group. The separate-group rule in section 393.124(d)(1) does not apply. |
The figures
| Figure | Value | Note |
|---|---|---|
| Pipe inside diameter | 24 in | Section 393.124 (e), pipe up to 45 in |
| Pipes in the group | 8 | 2,000 lb each |
| Group weight | 16,000 lb | Section 393.124(b)(1) |
| Required aggregate WLL | 8,000 lb | Half the group weight |
| Tiedown working load limit | 6,600 lb each | 3/8-in Grade 70 chain |
| Aggregate WLL provided | 39,600 lb | Cross-vehicle routing counts the full WLL of each tiedown |
| Transverse tiedowns required | 2 | One per 10 ft of load length |
| Tiedowns required in total | 4 | Front and rear diagonals plus transverse plus extras |
| Tiedowns on the group | 6 | Meets the requirement |
What to do
- No actions for this result.
Notes
- A transverse tiedown through a pipe on an upper tier or over longitudinal tiedowns secures all pipes beneath on which that tiedown causes pressure (section 393.124(b)(2)).
- Blocking on one side is one piece extending at least half the distance from the center to each end of the pipe, with two pieces on the opposite side, one at each end (section 393.124(c)(2)).
- Inspect the cargo and the tiedowns within the first 50 miles after beginning the trip, then reexamine them whenever duty status changes, after 3 hours or after 150 miles, whichever comes first (section 392.9(b)).
- A damaged tiedown is a violation and does not count toward the tiedown count or the aggregate working load limit. Replace it before the load rolls.
- Manufacturer markings govern the working load limit. The table values in section 393.108 apply to tiedowns not marked with a working load limit. The working load limit of a tiedown is the lowest working load limit of any component, including the tensioner, or of the anchor points, whichever is less.
This calculator applies 49 CFR 393.124 and the related sections to your answers. Confirm the measurements with a tape before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.
Quick answer: Concrete pipe on a flatbed or lowboy trailer is secured under 49 CFR 393.124. The aggregate working load limit of the tiedowns on any group of pipes must be at least half the weight of the group. Pipe up to 45 inches inside diameter follows one tiedown pattern and pipe over 45 inches follows another. Blocking must be at least 4 by 6 inches for timber, upper tiers sit only in wells and bell pipe loads on spacers with the bells placed by rule. This calculator checks a load against each rule and shows what to fix.
What does 49 CFR 393.124 require for concrete pipe?
Section 393.124 is the commodity-specific securement rule for concrete pipe. It sits in Part 393, Subpart I, beside the rules for logs, metal coils, paper rolls and other cargo that needs its own pattern. The general securement rules in sections 393.100 through 393.114 still apply underneath it. Where the pipe rule gives an additional requirement, the pipe rule governs.
The rule splits the load at 45 inches of inside diameter. Pipe up to 45 inches follows paragraph (e). Pipe over 45 inches follows paragraph (f). The split matters because large pipe gets a tiedown through every pipe, while smaller pipe may be secured with longitudinal tiedowns plus transverse tiedowns. The diameter you enter decides which pattern the calculator applies.
Five numbers carry most of the rule. The table below lists them with the paragraph that sets each one.
| Requirement | Figure | Source |
|---|---|---|
| Aggregate working load limit | At least half the group weight | 393.124(b)(1) |
| Transverse tiedowns, pipe up to 45 in | One per 10 ft of load length | 393.124(e)(2)(ii)(B) |
| Through-pipe tiedown angle | Not more than 45 degrees with the horizontal | 393.124(e)(1)(iii), (e)(2)(ii)(C), (e)(2)(ii)(D), (f)(2) |
| Timber blocking | At least 4 by 6 in | 393.124(c)(4) |
| Longitudinal tiedown, pipe up to 45 in | One 1/2-in chain or wire rope, or two 3/8-in | 393.124(e)(2)(ii)(A) |
The calculator runs one group of pipes at a time. A group is pipe of one diameter loaded together. Where a load mixes diameters, the rule requires separate groups and the calculator checks one group per run. Enter the group, answer the arrangement questions and the calculator returns a verdict with a check table, the figures and the actions to take.
Does the concrete pipe rule apply to every pipe load?
No. Section 393.124 applies to concrete pipe on flatbed trailers, flatbed vehicles and lowboy trailers. Two kinds of load fall outside it. Concrete pipe bundled tightly together into a single rigid article that has no tendency to roll is secured under the general rules in sections 393.100 through 393.114. Concrete pipe loaded in a sided vehicle or container is secured the same way. Pick either case in the calculator and it applies the general rules instead: aggregate working load limit under section 393.106(d) and tiedown count under section 393.110.
The general rules still demand real securement. The aggregate working load limit must be at least half the weight of the article or group. The tiedown count follows the length of the article and whether it is blocked against forward movement. A blocked article needs one tiedown per 10 feet.
An unblocked article follows the stepped count in section 393.110(b): one tiedown for an article 5 feet or less in length and 1,100 pounds or less in weight, two tiedowns for a short heavy article or an article over 5 feet to 10 feet. A longer article needs two tiedowns plus one more for every 10 feet or fraction beyond the first 10 feet. Cargo likely to roll must be restrained by chocks, wedges, a cradle or other equivalent means.
Side stakes on a flatbed do not turn it into a sided vehicle. The exception covers a vehicle or container with sides that contain the load. Where the pipe can roll off the deck, the pipe rule applies. When in doubt, secure the load as if the pipe rule applies: it is the stricter test for a flatbed load.
How many tiedowns does a concrete pipe load need?
The count depends on the pipe diameter and on the method chosen for smaller pipe. For pipe over 45 inches the rule is direct: at least one tiedown through each pipe. For pipe up to 45 inches the driver chooses between a tiedown through each pipe and a longitudinal-plus-transverse pattern. The calculator works out the minimum for the load described.
For pipe up to 45 inches, each pipe may be secured individually with a tiedown through the pipe. Where the pipes are not secured individually, one 1/2-inch chain or wire rope, or two 3/8-inch chain or wire rope, must run longitudinally over the group, with one transverse tiedown for every 10 feet of load length. The transverse tiedowns may pass through a pipe or over both longitudinal tiedowns between two pipes on the top tier.
Two more tiedowns sit at the ends of the bottom tier. At least one tiedown through the front pipe of the bottom tier must run aft at an angle not more than 45 degrees with the horizontal, whenever practicable. At least one tiedown through the rear pipe must run forward at the same angle. Those two tiedowns hold every pipe in the bottom tier firmly in contact with the adjacent pipe.
Top-tier end pipes can add tiedowns of their own. Where the first pipe of a group in the top tier is not placed in the first well formed by pipes at the front of the tier beneath, it needs an additional tiedown running rearward at not more than 45 degrees. The same applies at the rear, with the extra tiedown running forward. A load with both end pipes out of their end wells needs two extra tiedowns.
For pipe over 45 inches, each pipe in the front half of the load needs at least one tiedown through the pipe running rearward. Each pipe in the rear half needs at least one tiedown through the pipe running forward. The front half includes the middle pipe where the count is odd. Where the front or rear pipe is not in contact with a vehicle end structure, stakes, a locked pipe unloader or other equivalent means, that pipe needs at least two tiedowns through it. A single pipe is treated as a front and rear article, so it needs two tiedowns, one in each direction. Pipes loaded without contact between them are each treated the same way.
The count is a minimum, not a target. The aggregate working load limit check can demand more tiedowns than the pattern count. The calculator tests both. Where the two disagree, the larger number governs.
What is the aggregate working load limit for a group of pipes?
The aggregate working load limit of all tiedowns on any group of pipes must not be less than half the total weight of all the pipes in the group. That is section 393.124(b)(1). A group of eight pipes at 2,000 pounds each weighs 16,000 pounds, so the tiedowns on that group must add up to at least 8,000 pounds of aggregate working load limit.
Aggregate working load limit is not the sum of the tiedown ratings. Section 393.106(d) sets how each tiedown counts. A tiedown that runs from an anchor point on the vehicle through, over or around the cargo to an anchor point on the other side of the vehicle counts at its full working load limit. A tiedown that runs to an anchor point on the same side of the vehicle, or direct from a vehicle anchor to an anchor on the cargo, counts at half its working load limit. The calculator applies the routing you pick.
The working load limit of a tiedown is the lowest working load limit of any of its components, including the tensioner, or the working load limit of the anchor points it is attached to, whichever is less. A strong chain on a weak anchor is a weak tiedown. Manufacturer markings govern: the table values in section 393.108 apply to tiedowns not marked with a working load limit.
The table below gives the working load limit of the tiedowns drivers most often carry on a pipe load. The full tables, covering every chain grade, wire rope construction, rope fiber and steel strapping size, sit on the Flatbed Calculator page.
| Tiedown | Working load limit |
|---|---|
| 3/8-in Grade 70 chain | 6,600 lb |
| 1/2-in Grade 70 chain | 11,300 lb |
| 5/16-in Grade 70 chain | 4,700 lb |
| 1/2-in wire rope, 6 by 37 fiber core | 5,300 lb |
| 3/8-in wire rope, 6 by 37 fiber core | 3,000 lb |
| 4-in synthetic webbing | 4,000 lb |
| 3-in synthetic webbing | 3,000 lb |
| 2-in synthetic webbing | 2,000 lb |
A transverse tiedown through a pipe on an upper tier or over longitudinal tiedowns secures all pipes beneath on which it causes pressure. That is section 393.124(b)(2). One transverse tiedown over the top of a stack can therefore count toward the securement of the pipes below it, so long as it bears on them. The calculator counts every tiedown you enter toward the group total.
Damaged tiedowns do not count. A tiedown with a cut, a broken link or a damaged tensioner is a violation and it adds nothing to the tiedown count or to the aggregate working load limit. Replace it before the load rolls.
How do you block a concrete pipe load?
Blocking keeps the pipe from rolling and from shifting. Section 393.124(c) sets four requirements. Blocking may be one or more pieces placed symmetrically about the center of a pipe. One piece must extend at least half the distance from the center to each end of the pipe, with two pieces placed on the opposite side, one at each end. Blocking must be placed firmly against the pipe and secured to prevent it moving out from under the pipe. Timber blocking must have minimum dimensions of at least 4 by 6 inches.
The 4 by 6 inch minimum applies to timber. Blocking of another material is not bound by that figure, but it must still sit firmly against the pipe and be secured against moving out. The calculator asks about the blocking size and material. It also asks whether the blocking is placed symmetrically, firm against the pipe and secured.
Blocking also immobilizes the ends of the load. For pipe up to 45 inches, the bottom tier must be immobilized longitudinally at each end by blocking, vehicle end structure, stakes, a locked pipe unloader or other equivalent means. For pipe over 45 inches, the front pipe and the rear pipe must be immobilized the same way, with wedges added to the list. Other pipe in the bottom tier may also be held in place by blocks and wedges.
How do you stack concrete pipe in tiers?
Pipe stacks in a pyramid: each upper pipe rests in the well formed by two pipes below it. Section 393.124(d) sets the arrangement rules. Pipe of different diameters forms separate groups, each secured on its own. The bottom tier covers the full length of the vehicle or forms a partial tier in one group or two groups. The top tier is a complete tier, a partial tier in one group or a partial tier in two groups.
The well rule is the one that shapes the stack. Pipe must be placed only in the wells formed by adjacent pipes in the tier beneath. A third or higher tier must not be started unless all wells in the tier beneath are filled. A pipe that sits on a single pipe below it, or on the deck beside a well, breaks the rule. The same well logic shapes log loads. The Log Securement Calculator applies the matching rules for that cargo.
The geometry sets a minimum pipe count for each tier count. Two tiers need at least three pipes: two below forming one well and one above. Three tiers need at least six pipes: three below, two in the middle and one on top. The calculator checks the count against the tier count and flags a stack that cannot be built.
Lumber and building products stack under a different pattern, with spacers and unitized layers instead of wells. Where a flatbed carries both pipe and lumber, each commodity follows its own rule. The Lumber Securement Calculator covers the lumber side of a mixed flatbed load.
How do you secure bell pipe?
Bell pipe carries a flared bell at one end. That flare changes the loading. Section 393.124(d)(5) sets six rules for it. Bell pipe must be loaded on at least two longitudinal spacers of sufficient height to ensure that the bell is clear of the deck. The spacers run lengthwise under the pipe and lift the bell off the deck so it bears no weight.
In a single tier, the bells alternate on opposite sides of the vehicle. In more than one tier, the bells of the bottom tier all sit on the same side of the vehicle. Pipe in every upper tier loads with its bells on the opposite side to the bells of the tier below.
One more rule covers an incomplete second tier. Where the second tier is not complete, pipe in the bottom tier which do not support a pipe above must have their bells alternating on opposite sides of the vehicle. The calculator asks about that case only where the second tier is partial.
The ends of consecutive pipe must be staggered, if possible, within the allowable width. Otherwise they must be aligned. Staggering spreads the bells along the load and keeps the stack even. The calculator notes the rule wherever bell pipe is selected.
What changes when the pipe is over 45 inches?
Large pipe loses the longitudinal option. Paragraph (f) requires a tiedown through every pipe, with direction set by position: front-half pipes pull rearward and rear-half pipes pull forward. The front half includes the middle pipe where the count is odd. Every tiedown runs at an angle not more than 45 degrees with the horizontal, whenever practicable.
The end pipes carry an extra condition. Where the front or rear pipe is not in contact with a vehicle end structure, stakes, a locked pipe unloader or other equivalent means, that pipe needs at least two tiedowns through it instead of one. Contact with the end structure is what lets a single tiedown do the job. The calculator asks about front and rear contact separately and raises the count where contact is missing.
Single pipes and isolated pipes are treated as front and rear articles at once. A single pipe needs two tiedowns through it, one running rearward and one running forward. Several pipes transported without contact between them are each treated the same way, so each needs two tiedowns. That doubles the count fast on a load of large pipe with gaps between the pieces.
Large pipe also needs end immobilization without exception: the front pipe and the rear pipe must be immobilized by blocking, wedges, vehicle end structure, stakes, a locked pipe unloader or other equivalent means. The 45 inch line is measured on inside diameter, so check the pipe specification rather than the outside of the barrel. A pipe with a 45 inch inside diameter follows paragraph (e). A pipe at 45 and one half inches follows paragraph (f). Before the load rolls, run the Pre-Trip Inspection Checklist for the cargo securement check that goes with every flatbed departure.
How do you use the Concrete Pipe Securement Calculator?
- Pick the vehicle type: flatbed trailer, lowboy trailer, sided vehicle or container, or bundled rigid pipe.
- Enter the pipe inside diameter in inches, the number of pipes in the group and the weight of one pipe in pounds.
- Describe the load: tiers, bottom and top tier arrangement, bell pipe, blocking and end immobilization.
- Pick the tiedown method for pipe up to 45 in, or answer the bracing questions for pipe over 45 in.
- Enter the tiedown type, the number of tiedowns on the group and how they are routed.
- Read the verdict, the check table and the figures. Copy the summary for the trip records, or reset the calculator to start over.
Frequently asked questions
How many tiedowns does a concrete pipe load need?
It depends on the pipe diameter. For pipe over 45 inches inside diameter, each pipe needs at least one tiedown through the pipe, with two through an end pipe that is not in contact with an end structure, stakes or a locked pipe unloader. For pipe up to 45 inches, each pipe may be secured individually with a tiedown through the pipe, or the load may use one 1/2-inch chain or wire rope, or two 3/8-inch chain or wire rope, longitudinally over the group plus one transverse tiedown per 10 feet of load length. The bottom tier also needs a tiedown through the front pipe running aft and one through the rear pipe running forward.
What is the aggregate working load limit for concrete pipe?
The aggregate working load limit of all tiedowns on any group of pipes must be at least half the total weight of the pipes in the group. A tiedown that runs to an anchor on the other side of the vehicle counts at its full working load limit. A tiedown that runs to an anchor on the same side, or direct to the cargo, counts at half its working load limit. Manufacturer markings govern the rating. The table values in section 393.108 apply to unmarked tiedowns.
Can concrete pipe be stacked in tiers?
Yes, with the well rule. Pipe in an upper tier must sit only in the wells formed by adjacent pipes in the tier beneath. A third tier must not start unless all wells in the tier beneath are filled. The bottom tier covers the full length of the vehicle or forms a partial tier in one group or two groups. The top tier is a complete tier, a partial tier in one group or a partial tier in two groups.
How do you secure bell pipe?
Bell pipe loads on at least two longitudinal spacers tall enough to keep the bell clear of the deck. In one tier, the bells alternate on opposite sides of the vehicle. In more than one tier, the bottom-tier bells all sit on the same side and each upper tier loads with its bells on the opposite side to the tier below. Where the second tier is not complete, bottom-tier pipe that supports no pipe above has its bells alternating. The ends of consecutive pipe are staggered where possible within the allowable width.
What size timber blocking does concrete pipe need?
Timber blocking for concrete pipe must measure at least 4 by 6 inches. Blocking is placed symmetrically about the center of a pipe: one piece extends at least half the distance from the center to each end on one side, with two pieces on the opposite side, one at each end. Blocking must sit firmly against the pipe and be secured to prevent it moving out from under the pipe.
Does 49 CFR 393.124 apply to pipe in a sided trailer?
No. Concrete pipe loaded in a sided vehicle or container is secured under the general rules in sections 393.100 through 393.114, not under section 393.124. The same applies to concrete pipe bundled tightly together into a single rigid article with no tendency to roll. The general rules still require an aggregate working load limit of at least half the weight and a tiedown count under section 393.110.
Related tools
- Flatbed Calculator: the full tiedown working load limit tables and the general cargo securement rules.
- Log Securement Calculator: tiering and well rules for log loads.
- Lumber Securement Calculator: securement for lumber and building products.
- Metal Coil Securement Calculator: securement for metal coils on a flatbed.
- Heavy Equipment Securement Calculator: securement for equipment at 10,000 pounds and over.
- Intermodal Container Securement Calculator: securement for containers on a chassis.
- Pre-Trip Inspection Checklist: the cargo securement check before the load rolls.
Sources
- 49 CFR 393.124: Specific securement requirements for concrete pipe (eCFR, read Nov 19, 2026)
- 49 CFR 393.106: General requirements for securing articles of cargo (eCFR, read Nov 19, 2026)
- 49 CFR 393.108: Determining the working load limit of a tiedown (eCFR, read Nov 19, 2026)
- 49 CFR 393.110: Additional requirements for determining the minimum number of tiedowns (eCFR, read Nov 19, 2026)
- 49 CFR 392.9: Inspection of cargo, cargo securement devices and systems (eCFR, read Nov 19, 2026)