Skip to main content

Trucking Mind

One stack at a time. This calculator runs one stack of logs against 49 CFR 393.116. The headline number is the aggregate working load limit: at least one-sixth of the stack weight, not one-half. A result that fails means the load must not roll until the failed item is fixed.

Pick the load type, enter the weight and the log length, answer the setup questions for that load type. Every answer updates as you change each field.

The load

Shortwood is logs up to 16 ft long. Longwood is logs over 16 ft long (49 CFR 393.5).

The vehicle and the setup

Tiedowns or wrappers

Use the manufacturer marking on each device. A 3/8 in Grade 70 chain is marked 6,600 lb.

Meets 49 CFR 393.116

Every check passes for this load.

CheckResultDetail
Aggregate working load limitPassRequired: 6,667 lb, one-sixth of the 40,000 lb stack (49 CFR 393.116(b)(4)). Your tiedowns give 13,200 lb of aggregate working load limit.
Tiedown countPass2 tiedowns required for one stack of shortwood loaded crosswise (49 CFR 393.116(d)(2)). You entered 2.
Lower-tier overhangPassThe end of a lower-tier log may extend no more than one-third of the log length beyond the nearest support: 2 ft 8 in for the 8 ft log. Your overhang is 2 ft (49 CFR 393.116(d)(1)).
Tiedown placementInfoPlace the tiedowns at about one-third and two-thirds of the length of the logs: 2 ft 8 in and 5 ft 4 in from the end of the 8 ft log. The tiedowns attach to the vehicle frame at the front and rear of the load and cross the load in that direction (49 CFR 393.116(d)(2) and (d)(3)).
Center stakesInfoThe vehicle is 32 ft long. Center stakes are required only on a vehicle more than 33 ft long (49 CFR 393.116(d)(4)).

The figures

FigureValueNote
Stack weight40,000 lbWeight of the stack being secured
Required aggregate WLL6,667 lbOne-sixth of the stack (393.116(b)(4))
Actual aggregate WLL13,200 lbMeets the requirement
Each tiedown counts as6,600 lbCross-vehicle tiedowns count in full (393.106(d))
Devices required2Minimum count for this load
Devices entered2Meets the minimum
Maximum lower-tier overhang2 ft 8 inOne-third of the 8 ft log length
Tiedown positions2 ft 8 in and 5 ft 4 inOne-third and two-thirds of the log length

What to do

  • No actions for this result.

Notes

  • Logs must be solidly packed, with the outer bottom logs resting solidly against the bunks, bolsters, stakes or standards (49 CFR 393.116(c)(1)).
  • Each outside log must touch at least two stakes, bunks, bolsters or standards (49 CFR 393.116(c)(2)).
  • The center of the highest outside log on each side or end must sit below the top of each stake, bunk or standard (49 CFR 393.116(c)(3)).
  • A log not held in place by contact with other logs or the stakes, bunks or standards must be held by a tiedown (49 CFR 393.116(c)(4)).
  • Stakes or standards that are not permanently attached must be secured so they cannot separate from the vehicle in transit (49 CFR 393.116(b)(2)).
  • Inspect the cargo and the securement within the first 50 miles, at each change of duty status, then after every 3 hours of driving or 150 miles, whichever comes first (49 CFR 392.9(b)).
  • A damaged tiedown does not count toward the tiedown count or the aggregate working load limit. It is a violation, not an out-of-service condition on its own.
  • Working load limits come from the manufacturer marking on each device. Unmarked tiedowns use the default values in 49 CFR 393.108.

This calculator applies 49 CFR 393.116 to your answers. Check the current regulation and your company policy before you rely on a result.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.

Quick answer: Log securement follows 49 CFR 393.116, not the general cargo rules. The headline number is the aggregate working load limit: at least one-sixth of the stack weight, not one-half. Two tiedowns secure one stack of shortwood loaded crosswise, placed at about one-third and two-thirds of the log length, with no lower-tier log end sticking out more than one-third of the log length past the nearest support. This calculator runs one load against the rule and shows the tiedown count, the placement, the aggregate working load limit and the stake and bunk requirements.

Last reviewed: · Focus keyword: log securement requirements

What is the aggregate working load limit for logs?

The aggregate working load limit for a stack of logs is at least one-sixth of the weight of the stack. That is the rule in 49 CFR 393.116(b)(4). It applies to tiedowns used to secure a stack of logs on a frame vehicle or on a flatbed vehicle equipped with bunks, bolsters or stakes. One-sixth is the figure drivers get wrong most often, because the general cargo rule in 49 CFR 393.106(d) sets the aggregate working load limit at one-half of the weight. Logs are different. The bunks, stakes and bolsters do part of the restraining work, so the tiedowns carry a smaller share of the job.

The arithmetic is simple. Divide the stack weight by six and round up. A 40,000 lb stack needs at least 6,667 lb of aggregate working load limit. A 60,000 lb stack needs 10,000 lb. A 30,000 lb stack needs 5,000 lb. The table below gives the required figure for common stack weights.

Stack weightRequired aggregate WLL (one-sixth)General rule for comparison (one-half)
20,000 lb3,334 lb10,000 lb
30,000 lb5,000 lb15,000 lb
40,000 lb6,667 lb20,000 lb
50,000 lb8,334 lb25,000 lb
60,000 lb10,000 lb30,000 lb
80,000 lb13,334 lb40,000 lb

Getting the fraction wrong cuts both ways. A driver who applies one-half to a log load over-secures it: safe, but the extra chains cost time and money. A driver who applies one-sixth to general cargo under-secures it: the load fails the general rule by a wide margin. The calculator on this page applies one-sixth to log loads under 393.116 and one-half to exception loads that fall under the general rules, so the two cases stay separate.

How each tiedown counts toward the aggregate depends on how it attaches. Section 393.106(d) sets the method: a tiedown attached to an anchor point and to the cargo counts at half its working load limit, a tiedown that passes through or around the cargo and attaches to an anchor point on the same side counts at half. A tiedown that passes through or around the cargo and attaches to anchor points on opposite sides counts in full. Log tiedowns usually pass over the load and attach on both sides, so they count in full. A direct tiedown from an anchor point to the cargo counts at half, which is why the calculator asks how the tiedowns attach.

Working load limits come from the manufacturer marking on each device. A 3/8 in Grade 70 transport chain is marked 6,600 lb, so two of them passed over a 40,000 lb stack give 13,200 lb of aggregate working load limit against a 6,667 lb requirement. Unmarked tiedowns use the default values in 49 CFR 393.108. A damaged tiedown does not count toward the tiedown count or the aggregate working load limit at all. The Flatbed Calculator carries the full working load limit tables for chains, webbing, wire rope and strapping.

What counts as shortwood and what counts as longwood?

The line between shortwood and longwood is 16 ft. Section 393.5 defines shortwood as all logs typically up to 4.9 m (16 ft) long: cut-up logs, cut-to-length logs, bolts or pulpwood. Longwood is all logs that are not shortwood, meaning logs over 4.9 m (16 ft) long, usually described as long logs or treelength. A 16 ft log is shortwood. A 17 ft log is longwood.

The distinction matters because the rule splits by log type. Shortwood loaded crosswise has its own paragraph, 393.116(d), with the one-third overhang rule and the tiedown positions. Shortwood loaded lengthwise falls under 393.116(e)(1), with the blocked-front-and-rear option for a single tiedown. Longwood falls under 393.116(e)(2), with the two-or-more-bunks rule. Pole trailer rules in 393.116(f) cover either type. Pick the wrong paragraph and the tiedown count comes out wrong.

Shortwood loaded crosswise is usually no more than 2.6 m (102 in) long, per the same definition. That matches the width of a trailer: a crosswise log sits across the vehicle, so its length is close to the vehicle width. Longer shortwood usually loads lengthwise instead. The calculator asks for the log length and the load type together, so the crosswise checks only run on crosswise loads.

How do you secure shortwood loaded crosswise?

Crosswise shortwood on a frame, rail or flatbed vehicle follows 393.116(d), on top of the general component and use rules in paragraphs (b) and (c). Four numbers govern the setup: one-third, two tiedowns, one-third and two-thirds, plus 33 ft.

First, no lower-tier log end may extend more than one-third of the log length beyond the nearest supporting structure on the vehicle. For an 8 ft log the limit is 2 ft 8 in. For a 12 ft log it is 4 ft. Measure from the nearest bunk, bolster or stake to the end of the log. The rule covers the lower tier because that tier carries the stack above it: an overhanging lower-tier log is a lever that can shift the whole stack.

Second, one stack of shortwood loaded crosswise needs at least two tiedowns. The tiedowns attach to the vehicle frame at the front and rear of the load and cross the load in that direction. They do not run across the logs. They run along the vehicle, over the stack, from the front frame to the rear frame.

Third, when two tiedowns are used they sit at approximately one-third and two-thirds of the length of the logs. For an 8 ft log that means 2 ft 8 in and 5 ft 4 in from the end of the log. For a 12 ft log it means 4 ft and 8 ft. The word approximately gives room for the realities of a load: a tiedown a few inches off the mark still satisfies the rule, while a tiedown bunched at one end does not.

Fourth, a vehicle more than 10 m (33 ft) long must have center stakes or comparable devices dividing it into sections approximately equal in length. Where the vehicle is so divided, each tiedown must secure the highest log on each side of the center stake and fasten below those logs. The rule allows three ways to tension such a tiedown: fixed at each end and tensioned from the middle, fixed in the middle and tensioned from each end, or passed through a pulley or equivalent device in the middle and tensioned from one end. Any structure or stake that takes an upward force when the tiedowns are tensioned must be anchored to resist that force.

Two stacks side by side add four more conditions under 393.116(d)(6). There must be no space between the two stacks. The outside of each stack must rise at least 1 in within 4 in of the end of the logs or the side of the vehicle. The highest log must sit no more than 8 ft above the deck. At least one tiedown must run lengthwise across each stack. That is the tiedown requirement for two stacks: the two-tiedown rule in (d)(2) applies only when one stack is loaded, so two stacks need two tiedowns in total, one across each stack. The calculator checks all four conditions when you pick two stacks.

How do you secure logs loaded lengthwise?

Logs loaded lengthwise on a flatbed or frame vehicle follow 393.116(e). Shortwood and longwood take different paths. Both offer a choice between tiedowns and wrappers.

Shortwood loaded lengthwise must be cradled in a bunk unit or contained by stakes. It is then secured in one of three ways.

The first way is at least two tiedowns securing the stack to the vehicle. The second way is one tiedown, allowed only when all the logs in the stack are blocked in the front by a front-end structure strong enough to restrain the load or by another stack of logs, with blocking in the rear by another stack of logs or a vehicle end structure. When one tiedown is used it must sit about midway between the stakes. The third way is at least two tiedown-type devices, such as wire rope, used as wrappers that encircle the entire load at locations along the load that give effective securement.

Longwood must be cradled in two or more bunks. That is a hard floor: one bunk is never enough for longwood, however short the logs. Once the bunks are in place, longwood needs either at least two tiedowns at locations that give effective securement or at least two wrappers encircling the entire load at locations that give effective securement.

Wrappers deserve a closer look because they confuse drivers who know only tiedowns. A wrapper is a tiedown-type device that encircles the entire load and bundles the logs together. The rule states plainly that wrappers used to bundle the logs together are not required to attach to the vehicle. That is the point of a wrapper: it holds the bundle together so the bunks and stakes can hold the bundle on the vehicle. A wrapper that only circles part of the load is not a wrapper under the rule. The locations must give effective securement, which means spaced along the load where they can hold the bundle, not bunched at one end.

One more exception sits in paragraph (b)(3). Tiedowns are not required at all when the logs travel in a crib-type log trailer and are loaded in compliance with paragraphs (b)(2) and (c). A crib-type log trailer has stakes, bunks, a front-end structure and a rear structure that restrain the logs in every direction. The calculator offers the crib-type option for lengthwise loads and drops the tiedown checks when you pick it.

What are the rules for logs on a pole trailer?

Logs on a pole trailer follow 393.116(f). A pole trailer carries the logs lengthwise on bunks, with the trailer frame reduced to a pole between the bunks. The securement rule gives two options: at least one tiedown at each bunk, or at least two tiedowns used as wrappers that encircle the entire load at locations along the load that give effective securement.

The tiedown option scales with the trailer. A two-bunk pole trailer needs at least two tiedowns. A three-bunk pole trailer needs at least three. Each bunk gets its own tiedown. The wrapper option stays at two wrappers whatever the bunk count, because the wrappers bundle the load rather than anchoring it bunk by bunk.

When wrappers are used, the front and rear wrappers must sit at least 3.04 m (10 ft) apart. That spacing keeps the bundle held at two well-separated points along its length. Two wrappers close together hold one part of the load and leave the rest free to shift. The calculator checks the spacing when you pick the wrapper method on a pole trailer.

Large-diameter logs get two extra rules. Large-diameter single and double log loads must be immobilized with chock blocks or other equivalent means to prevent shifting. A single massive log has no neighboring logs to wedge against, so chocks do the job the stack would otherwise do. And large-diameter logs that rise above the bunks must be secured to the underlying load with at least two additional wrappers. Those wrappers sit on top of the first two, so a pole trailer with logs above the bunks needs four wrappers in total.

Which log loads fall outside 49 CFR 393.116?

Three kinds of log load fall outside the log rule entirely. Section 393.116(a) lists them. Each one then follows the general cargo securement rules in 49 CFR 393.100 through 393.114 instead.

The first exception covers logs unitized by banding or other comparable means. A banded bundle behaves like a single article of cargo, so the general rules fit it better than the log rules. The second exception covers loads of no more than four processed logs. Four logs or fewer is a small load. The general rules cover it. Five processed logs is a log load under 393.116.

The third exception covers firewood, stumps, log debris and other such short logs. These must travel in a vehicle or container enclosed on both sides, front and rear. The enclosure must be of adequate strength to contain them. Longer logs may also be loaded in an enclosed vehicle that way. The enclosure does the restraining, so the log rules do not apply. An open truck full of firewood meets neither rule: it is not enclosed, so the exception fails. It is not secured under 393.116 either.

The switch to the general rules changes the numbers sharply. The aggregate working load limit jumps from one-sixth to one-half of the weight. The tiedown count comes from 49 CFR 393.110: one tiedown for an article 5 ft or less and 1,100 lb or less, two tiedowns for an article 5 ft or less and over 1,100 lb or over 5 ft to 10 ft. Beyond 10 ft, add one tiedown for each additional 10 ft or part. A load blocked against forward movement needs one tiedown per 10 ft or part.

The calculator runs the general rules when you pick an exception load. For the full general securement picture, including the working load limit tables, use the Flatbed Calculator.

What must the vehicle and the load itself satisfy?

Before any tiedown count applies, the vehicle and the load must satisfy the component and use rules in paragraphs (b) and (c) of 393.116. These rules cover every log load under the section, whatever the load type.

The vehicle must be designed and built, or adapted, for the transportation of logs. It must be fitted with bunks, bolsters, stakes or standards, or other equivalent means, that cradle the logs and prevent them from rolling. Every component involved in securing the logs must be designed and built to withstand all anticipated operational forces without failure, accidental release or permanent deformation. Stakes or standards that are not permanently attached to the vehicle must be secured so they cannot separate from the vehicle in transit.

The load itself must be solidly packed, with the outer bottom logs in contact with and resting solidly against the bunks, bolsters, stakes or standards. Each outside log on the side of a stack must touch at least two stakes, bunks, bolsters or standards. If one end of a log does not actually touch a stake, it must rest on other logs in a stable manner and extend beyond the stake, bunk, bolster or standard. The center of the highest outside log on each side or end must sit below the top of each stake, bunk or standard: a log whose center rides above the stake top can roll over the stake.

Any log not held in place by contact with other logs or the stakes, bunks or standards must be held in place by a tiedown. And when the condition of the wood makes friction between logs so low that they are likely to slip on each other, additional tiedowns or securement devices must be used. Icy logs, wet logs and smooth-barked logs all fall in that category. The calculator asks about slippery wood and flags the extra securement when you say yes.

Securement does not end at departure. Section 392.9(b) requires the driver to inspect the cargo and the securement devices within the first 50 miles after beginning a trip, to re-examine them at each change of duty status, then to re-examine them after every 3 hours of driving or 150 miles, whichever comes first. Log loads settle and straps loosen, so the first 50-mile check matters. The Pre-Trip Inspection Checklist covers the cargo securement checks to run before you roll. Dressed lumber travels under a different rule: the Lumber Securement Calculator covers 49 CFR 393.118. Concrete pipe has its own rule too: the Concrete Pipe Securement Calculator covers 49 CFR 393.124.

How do you use the Log Securement Calculator?

  1. Pick the load type: shortwood crosswise, shortwood lengthwise, longwood, pole trailer or an exception load.
  2. Enter the stack weight in pounds and the log length in feet.
  3. Answer the setup questions for that load type: vehicle length and overhang for crosswise loads, bunk count for longwood and pole trailers, wrapper spacing for pole trailers.
  4. Enter the tiedowns or wrappers you plan to use: the count, the working load limit of each device and how the tiedowns attach.
  5. Read the verdict, the check table, the figures and the notes. A Fail result names the item to fix. A Check result names the item to confirm.
  6. Copy the summary for the trip records, or reset the calculator to start over.

Frequently asked questions

How many tiedowns do logs need?

It depends on the load. One stack of shortwood loaded crosswise needs 2 tiedowns. Shortwood loaded lengthwise needs 2 tiedowns, or 1 if every log is blocked in front and blocked in the rear, or 2 wrappers. Longwood needs 2 tiedowns or 2 wrappers. A pole trailer needs at least 1 tiedown at each bunk or at least 2 wrappers. Two stacks side by side need 2 tiedowns in total, at least 1 lengthwise across each stack.

What is the aggregate working load limit for a stack of logs?

At least one-sixth of the weight of the stack, under 49 CFR 393.116(b)(4). A 40,000 lb stack needs at least 6,667 lb of aggregate working load limit. The general cargo rule of one-half does not apply to logs secured under 393.116. It does apply to exception loads that fall under the general rules.

How far can a log stick out past the support?

The end of a lower-tier log loaded crosswise may extend no more than one-third of the log length beyond the nearest supporting structure. For an 8 ft log the limit is 2 ft 8 in. The rule is in 49 CFR 393.116(d)(1).

Do log wrappers have to attach to the vehicle?

No. Wrappers that bundle the logs together are not required to attach to the vehicle, under 49 CFR 393.116(e)(1)(iii), (e)(2)(ii) and (f)(1). They must encircle the entire load at locations that give effective securement. On a pole trailer the front and rear wrappers must sit at least 10 ft apart.

When does a log truck need center stakes?

When the vehicle is more than 33 ft long. Section 393.116(d)(4) requires center stakes or comparable devices dividing the vehicle into sections about equal in length. Each tiedown must secure the highest log on each side of the center stake and fasten below those logs.

Are four processed logs covered by 49 CFR 393.116?

No. Loads of no more than four processed logs use the general cargo securement rules in 49 CFR 393.100 through 393.114, under the exception in 393.116(a)(2). The aggregate working load limit is then one-half of the weight and the tiedown count comes from 393.110.

Related tools

Sources

Follow on WhatsApp Ask by Voice