Skip to main content

Trucking Mind

One load at a time. This calculator works out the securement pattern for one load of bundled lumber or building products under 49 CFR 393.118, with the tiedown count from 49 CFR 393.110 and the aggregate working load limit from 49 CFR 393.106(d). A result that says the load needs changes means the load must not roll until the changes are made.

Describe the load and the equipment on hand. Every answer updates as you change each field.

The load

The vehicle and the setup

The tiedowns

The values shown are the unmarked table values in 49 CFR 393.108. Use the marked working load limit on your tiedown if it differs. The marked value governs.

Leave the planned count blank to skip the check, or enter the number of tiedowns on hand to see whether the plan covers the requirement.

Securement pattern ready

The load meets 49 CFR 393.118 with 3 tiedowns. Work through the pattern tier by tier.

CheckResultDetail
Cargo covered by 49 CFR 393.118PassBundled lumber and building products are covered by 49 CFR 393.118. A bundle is a package of lumber, building materials or similar products unitized for securement as a single article of cargo (49 CFR 393.118(a)).
Bundle positioningPassBundles sit side by side in direct contact with each other, as 49 CFR 393.118(b) requires.
Multi-tier methodPassOption 3 under 49 CFR 393.118(d): bundles sit on spacers and the tiedown arrangement in 393.118(d)(3)(iv) applies, with the spacer rules in 393.118(d)(3)(i) through (iii).
Spacer widthPassSpacer width 4 in is equal to or greater than the spacer height 3.5 in, as 49 CFR 393.118(d)(3)(ii) requires.
Spacer constructionPassSpacers are single pieces of material, so the layered-spacer rule in 49 CFR 393.118(d)(3)(iii) is met.
Tiedown count by lengthPassBundles 16 ft long need 3 tiedowns over the top tier: 49 CFR 393.110(b)(3) needs two tiedowns past 10 ft plus one more for every 10 ft or part of 10 ft beyond the first 10 ft.
Aggregate working load limitPassThe aggregate working load limit of the tiedowns must be at least one-half the load weight: 12,000 lb for a 24,000 lb load (49 CFR 393.106(d)). Each tiedown over the load that anchors on both sides counts its full working load limit of 4,000 lb, so 3 tiedowns meet the limit and the length rule governs the total.

The figures

FigureValueNote
Bundles4Side by side across the deck
Tiers2Bundles stacked high
Bundle length16 ftTiedown count runs on this length
Total load weight24,000 lbAggregate limit is one-half: 12,000 lb
Tiedowns by the length rule349 CFR 393.110
Tiedowns by the aggregate limit349 CFR 393.106(d) at 4,000 lb each
Total tiedowns required3The higher of the two rules
Tiedowns over the top tier3Laid out over the top tier
Spacer width vs height4 in vs 3.5 inWidth must be equal to or greater than height

Securement pattern

  1. Tier 1 (bottom): bundles rest on the deck. Bundles sit in direct contact side by side.
  2. Tier 2 (top): 3 tiedowns over the top tier, spaced across the bundle length, over bundles resting on spacers.
  3. Spacers: each spacer runs long enough to support all pieces in the bottom row of the bundle above it. Its width is equal to or greater than its height. Layered spacers are unitized or fastened so each spacer performs as a single piece (49 CFR 393.118(d)(3)(i) through (iii)).

What to do

  • Inspect every tiedown before use. A damaged tiedown is a violation and does not count toward the tiedown count or the aggregate working load limit (49 CFR 393.104(b)).
  • Use edge protection wherever a tiedown touches a sharp bundle edge (49 CFR 393.104(f)(4)).
  • Check the load within the first 50 miles, then whenever your duty status changes or after 3 hours or 150 miles, whichever comes first (49 CFR 392.9(b)).

Notes

  • The aggregate working load limit counts each tiedown that runs over the load and anchors on both sides at its full working load limit (49 CFR 393.106(d)(3)). A tiedown anchored to the cargo itself or to the same side of the vehicle counts only one-half its working load limit.
  • Use the marked working load limit on your tiedown if it differs from the table value. The marked value governs (49 CFR 393.108(b)). Unmarked tiedowns take the table value for their type and size.
  • Each tiedown must be designed so the driver of an in-transit vehicle can tighten it. Steel strapping is the only exception (49 CFR 393.112).

This calculator applies 49 CFR 393.118, 393.106, 393.108 and 393.110 to your answers. Confirm the measurements with a tape before you rely on a result.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.

Quick answer: Bundled lumber rides under 49 CFR 393.118. Bundles sit side by side in direct contact or with a means to stop them shifting toward each other. One tier follows the general securement rules. More than one tier follows one of four options in the regulation: side stakes, blocking or friction devices between tiers, spacers or direct stacking with a set tiedown arrangement, or tiedowns over every tier. The tiedown count runs on bundle length under 49 CFR 393.110 and the aggregate working load limit must reach one-half the load weight under 49 CFR 393.106(d). This calculator works out the pattern, the count and the spacer checks for the load you describe.

Last reviewed: · Focus keyword: lumber securement FMCSA

What does FMCSA require for securing lumber bundles?

Section 393.118 of Title 49 covers bundles of dressed lumber, packaged lumber, building products such as plywood, gypsum board or other materials of similar shape. The rule turns on one word: bundle. A bundle is a package of lumber, building materials or similar products unitized for securement as a single article of cargo. Banded packs from the mill, shrink-wrapped units and strapped lifts all count as bundles. Loose boards do not. Lumber or building products which are not bundled or packaged must be treated as loose items under the general rules in sections 393.100 through 393.114.

The rule sets out five things. Bundles sit side by side in direct contact with each other, or a means must be provided to prevent bundles from shifting toward each other. Bundles carried on one tier follow the general provisions. Bundles carried in more than one tier follow one of four options. Bundles in a sided vehicle or container of adequate strength follow the general provisions. The table below maps each situation to its rule.

SituationRuleWhat it means
Loose lumber or building products393.118(a)General rules only. No lumber-specific tier options.
Bundles, one tier393.118(c)General rules: tiedown count plus aggregate working load limit.
Bundles, more than one tier393.118(d)One of four options: stakes, blocking or friction devices, spacers or direct stacking, tiedowns over each tier.
Bundles in a sided vehicle or container393.118(e)General rules only. The side must be of adequate strength.
Bundles side by side393.118(b)Direct contact, or a means to prevent shifting toward each other.

The general provisions do most of the work in every case. The tiedown count comes from section 393.110. The aggregate working load limit comes from section 393.106(d). The tiedown working load limit comes from the manufacturer marking or the tables in section 393.108. The lumber rule adds the positioning rule, the tier options and the spacer rules on top of that base. A driver who knows the general rules and the four tier options knows the whole of section 393.118.

Logs and paper rolls are close neighbours with different rules. Logs follow their own commodity rule in section 393.116, with an aggregate working load limit of one-sixth the stack weight instead of one-half. Use the Log Securement Calculator for a log load. Paper rolls follow section 393.122, with tipping ratios and stacking limits. Use the Paper Roll Securement Calculator for a paper roll load.

The rule has not changed in years. Section 393.118 was last amended on September 24, 2013. No amendment since has touched it. The text on this page was checked against the live regulation on November 19, 2026.

How many tiedowns does a lumber load need?

Two rules set the number. The higher number wins. The first rule counts tiedowns by length. The second rule counts tiedowns by weight. A load that passes the length rule can still fail the weight rule. The reverse holds too.

Article length and weightMinimum tiedownsSource
5 ft or less, 1,100 lb or less1393.110(b)(1)
5 ft or less, over 1,100 lb2393.110(b)(2)(i)
Over 5 ft to 10 ft, any weight2393.110(b)(2)(ii)
Over 10 ft2 plus 1 per additional 10 ft or part393.110(b)(3)
Blocked against forward movement1 per 10 ft or part393.110(c)

Worked example. Bundles 16 ft long need 3 tiedowns over the top tier: 2 for the first 10 ft plus 1 for the 6 ft past 10 ft. Bundles 20 ft long also need 3. Bundles 21 ft long need 4, because the foot past 20 ft starts a new part of 10 ft. Bundles 40 ft long need 5. The count runs on the length of the article or group of articles the tiedowns secure, so equal-length bundles in a tier count as one group.

The weight rule is the aggregate working load limit. Section 393.106(d) requires the aggregate working load limit of the tiedowns to be at least one-half the weight of the article or group of articles. A tiedown that runs over the load and anchors on the other side of the vehicle counts its full working load limit. A tiedown anchored to the cargo itself, or to the same side of the vehicle, counts only one-half its working load limit. Over-the-top tiedowns are the normal case on a lumber load, so each tiedown counts in full.

Worked example. A 24,000 lb load needs an aggregate working load limit of 12,000 lb. With 4-in webbing rated at 4,000 lb per tiedown, 3 tiedowns meet the limit exactly. The length rule also needs 3 for 16 ft bundles, so the answer is 3 either way.

The same load with 2-in webbing rated at 2,000 lb needs 6 tiedowns by weight. The weight rule governs even though the length rule needs only 3. Stronger tiedowns cut the count. A 3/8-in Grade 70 chain rated at 6,600 lb would meet the same 12,000 lb limit with 2 tiedowns, but the length rule still needs 3, so the answer stays 3. The Flatbed Calculator carries the full tiedown working load limit tables from section 393.108 for every tiedown type.

Multi-tier loads add tiedowns. Under the spacer option, a 3-tier load needs tiedowns over the middle tier as well as the top tier. A load with more than 3 tiers needs tiedowns over one middle tier as well as the top tier. Under the tiedowns-over-each-tier option, every tier gets its own tiedowns. The calculator adds those in and shows the total.

One more rule decides whether a tiedown counts at all. Section 393.104(b) prohibits the use of damaged securement devices. A tiedown with cuts, cracks or other damage that weakens it is a violation. It does not count toward the tiedown count or the aggregate working load limit. Count only tiedowns in proper working order. Edge protection is required wherever a tiedown would be subject to abrasion or cutting at the point where it touches the cargo. The Pre-Trip Inspection Checklist covers the cargo securement checks for the walkaround, with out-of-service flags for the defects that stop a trip.

How do you secure lumber stacked in more than one tier?

Section 393.118(d) gives four options for bundles carried in more than one tier. Any one of them meets the rule. Pick the option that matches the equipment on the trailer.

Option 1: stakes. The load is blocked against lateral movement by stakes on the sides of the vehicle and secured by tiedowns laid out over the top tier. The stakes do the lateral work. The tiedowns over the top hold the stack down and keep it together. This is the simplest option when the trailer has stake pockets and stakes in good order.

Option 2: blocking or friction devices. The load is restrained from lateral movement by blocking or high friction devices between tiers and secured by tiedowns laid out over the top tier. Friction mats between tiers grip the bundles above and below. Blocking wedged between tiers stops sideways movement. An unmarked friction mat counts as resistance equal to 50 percent of the weight placed on it.

Option 3: direct stacking or spacers. Bundles sit directly on top of other bundles or on spacers. The tiedown arrangement in section 393.118(d)(3)(iv) applies. Tiedowns go over the top tier under the general rules, with a minimum of two tiedowns for bundles longer than 5 ft. With 3 tiers, the middle and top bundles must be secured by tiedowns. With more than 3 tiers, one of the middle bundles and the top bundle must be secured. The middle tier secured may not exceed 6 ft above the deck of the trailer. Otherwise, the second tier from the bottom must be secured. Spacers must meet the three spacer rules in the next section.

Option 4: tiedowns over each tier. Every tier of bundles gets its own tiedowns under the general rules, with a minimum of two tiedowns over each of the top bundles longer than 5 ft, in all circumstances. This option needs the most tiedowns. It is the fallback when the trailer has no stakes, no friction devices, no blocking and no spacers. Fitting any of those cuts the count.

The middle-tier rule catches people out. With 3 tiers, the middle tier is tier 2 and it must be secured before the top tier goes on. With 4 or more tiers, pick a middle tier that tops out at 6 ft or less above the deck.

A load of four tiers at 24 in per bundle puts tier 3 at exactly 6 ft, so tier 3 is the middle tier to secure. A load of four tiers at 40 in per bundle puts tier 2 at 6 ft 8 in, past the limit, so the rule falls back to the second tier from the bottom. The calculator works out which middle tier to secure from the bundle height you enter. It flags the fallback when no middle tier sits at 6 ft or less.

What are the spacer rules for stacked lumber?

Three rules govern spacers under section 393.118(d)(3). They are short. Each one answers a real failure mode.

First, the length of spacers between bundles must provide support to all pieces in the bottom row of the bundle. A spacer that stops short of the outer pieces leaves them hanging. The unsupported pieces sag, shift and break the unit. Run each spacer the full width of the bundle above it, or use enough spacers to support every piece.

Second, the width of individual spacers must be equal to or greater than the height. A spacer 4 in wide and 3.5 in high passes. A spacer 3 in wide and 4 in high fails. The rule is about stability. A tall narrow spacer tips under load. A wide flat spacer stays put. Measure both dimensions before loading. Swap any spacer that fails the test.

Third, spacers made of layers of material must be unitized or fastened together so the spacer performs as a single piece of material. Loose layers slide against each other under braking and the stack walks. Nail, screw, strap or glue the layers together. Single-piece spacers need no fastening.

Spacers are dunnage as well as separators, so the general dunnage rule applies too. Section 393.104(d) requires material used as dunnage, blocking and bracing to be free of damage or defects which would compromise the effectiveness of the securement system. A cracked spacer, a rotted board or a spacer crushed from a past load fails that test even if its dimensions pass.

Do lumber bundles have to touch each other?

Yes, unless something stops them shifting. Section 393.118(b) requires bundles to be placed side by side in direct contact with each other, or a means must be provided to prevent bundles from shifting toward each other. One or the other. A gap with nothing in it fails the rule.

The reason is slack. Tiedowns run over the top of the whole group. If bundles can shift toward each other, the group narrows, the tiedowns lose tension and the load loosens in transit. Direct contact removes the gap. Blocking between bundles does the same job by filling it.

The same rule appears in the general provisions. Section 393.106(c)(2) requires articles placed beside each other and secured by transverse tiedowns to be placed in direct contact with each other or prevented from shifting toward each other. The lumber rule repeats it because lumber loads are the classic case: wide flat bundles side by side under transverse straps.

What counts as a means to prevent shifting? Blocking wedged between the bundles, bracing against the stakes or the side, or any fitting that holds the gap closed under braking and cornering. The means must hold for the whole trip, not just at loading. Check it at the first 50-mile inspection and at every reexamination after that.

What changes when lumber rides in a sided trailer or container?

Section 393.118(e) says that dressed lumber or similar building products loaded in a sided vehicle or container of adequate strength may be secured in accordance with the general provisions of sections 393.100 through 393.114. The four multi-tier options in section 393.118(d) do not apply. The tier count stops mattering to the rule, because the sides do the containing work that stakes, friction devices and spacers do on an open trailer.

Two conditions carry the whole section. The vehicle or container must be sided. The sides must be of adequate strength. A side that bows, cracks or gives under the load is not of adequate strength. The section does not cover the load. Inspect the sides, the posts and the fastenings before loading. A dry van in good order meets the test for ordinary lumber loads. A container with corroded walls or a flatbed with low sideboards that the load towers over does not.

The general rules still apply in full. Bundles beside each other must be in direct contact or prevented from shifting toward each other under section 393.106(c)(2). The tiedown count under section 393.110 still runs on bundle length. The aggregate working load limit under section 393.106(d) still needs one-half the load weight. The sided vehicle changes how the load is contained. It does not change how many tiedowns the load needs.

One practical point: tiedowns inside a van or container still need anchor points of adequate strength. The working load limit of the tiedown is the lowest working load limit of any of its components or the anchor points, whichever is less. A strong strap on a weak anchor point counts at the anchor point value.

What if the lumber is not bundled?

Section 393.118(a) answers it in one sentence. Lumber or building products which are not bundled or packaged must be treated as loose items and transported in accordance with sections 393.100 through 393.114. The lumber-specific rules do not apply. No tier options. No spacer rules. No bundle positioning rule, though the general side-by-side rule in section 393.106(c)(2) still applies to articles placed beside each other under transverse tiedowns.

Loose lumber is harder to secure than bundled lumber. Each piece or group of pieces must be firmly immobilized or secured by structures of adequate strength, dunnage or dunnage bags, shoring bars, tiedowns or a combination of these. Long boards need support along their length so they cannot bow and work loose. Short pieces need containment so they cannot slide out from under the tiedowns. The tiedown count runs per article or group of articles, so a load of mixed lengths needs the count worked out for each group.

The practical fix is to bundle the load before it goes on the trailer. Banding, strapping or wrapping the lumber into units turns loose items into bundles and brings section 393.118 into play, with its simpler tier options. Most mills and yards ship lumber banded for exactly this reason. If the load arrives loose, ask the shipper to band it, or band it on the dock before loading.

This calculator handles loose loads too. Pick the loose option and it applies the general rules: the tiedown count by length and the aggregate working load limit. It flags that section 393.118 does not cover the load, so the tier options and spacer checks do not appear.

How do you use the Lumber and Building Products Securement Calculator?

  1. Pick the cargo type, then enter the number of bundles side by side, the number of tiers, the bundle length in feet and the bundle height in inches.
  2. Enter the total load weight in pounds. The aggregate working load limit runs on this figure.
  3. Pick the vehicle type and say whether the bundles touch side by side. If there is a gap, say whether blocking or bracing stops the bundles shifting toward each other.
  4. For more than one tier, pick what sits between the tiers. If you use spacers, enter the spacer width and height and say how the spacers are built.
  5. Pick the tiedown type, or enter the marked working load limit for a custom tiedown. Enter the tiedowns you plan to use to check the plan against the requirement.
  6. Read the verdict, the check table, the figures and the pattern. Work through the pattern tier by tier, then copy the summary for the trip records.

Frequently asked questions

How many tiedowns do I need for a lumber load?

The count runs on bundle length under 49 CFR 393.110. The aggregate working load limit must reach one-half the load weight under 49 CFR 393.106(d). The higher number governs. Bundles 16 ft long need 3 tiedowns over the top tier by length. A 24,000 lb load needs 12,000 lb of aggregate working load limit, which is 3 tiedowns at 4,000 lb each. Multi-tier loads add tiedowns over a middle tier or over every tier, depending on the option used.

Can I stack lumber bundles without spacers?

Yes, if another option in 49 CFR 393.118(d) covers the load. Side stakes block lateral movement, or blocking or high friction devices between tiers restrain it. Bundles may also sit directly on top of other bundles under option 3, with the tiedown arrangement in section 393.118(d)(3)(iv). With no stakes, no friction devices, no blocking and no spacers, the only option left is tiedowns over each tier.

How wide must spacers be under lumber bundles?

The width of individual spacers must be equal to or greater than the height, under 49 CFR 393.118(d)(3)(ii). A spacer 4 in wide and 3.5 in high passes. A spacer 3 in wide and 4 in high fails. Spacers must also run long enough to support all pieces in the bottom row of the bundle. Layered spacers must be unitized or fastened so each spacer performs as a single piece.

Do lumber bundles have to touch each other?

Bundles must sit side by side in direct contact with each other, or a means must be provided to prevent bundles from shifting toward each other, under 49 CFR 393.118(b). A gap with nothing in it fails the rule. Blocking wedged between the bundles is the usual means. The same rule appears in the general provisions at 49 CFR 393.106(c)(2).

What is the 6-foot rule for stacked lumber?

With more than 3 tiers under the spacer or direct-stacking option, one middle bundle and the top bundle must be secured. The middle tier secured may not exceed 6 ft above the deck of the trailer, under 49 CFR 393.118(d)(3)(iv)(B)(2)(i). If no middle tier sits at 6 ft or less, the rule falls back to the second tier from the bottom. With exactly 3 tiers, the middle and top bundles must be secured.

Does 49 CFR 393.118 apply to loose lumber?

No. Section 393.118(a) says lumber or building products which are not bundled or packaged must be treated as loose items and transported under the general rules in 49 CFR 393.100 through 393.114. The tier options and spacer rules do not apply. Banding or strapping the lumber into bundles brings the load under section 393.118.

Related tools

Sources

Follow on WhatsApp Ask by Voice