Skip to main content

Trucking Mind

One load at a time. This calculator gives the tiedown pattern for one coil or one row of coils under 49 CFR 393.120, plus the aggregate WLL check under section 393.106(d). A result that fails means the load must not roll until the failed check is fixed.

Enter the coil weight, pick the eye position and the vehicle, then check the pattern. Every answer updates as you change each field.

The load

The tiedowns

Restraint

Ready to secure: pattern complete

Eye vertical, single coil: 3 tiedowns plus forward restraint

The pattern is complete once you add the extra tiedowns listed below.

The tiedown pattern

  1. Tiedown 1: diagonally through the eye, from the left side near the front of the coil to the right side near the rear of the coil.
  2. Tiedown 2: diagonally through the eye, from the right side near the front of the coil to the left side near the rear of the coil. The two diagonals form an X over the eye.
  3. Tiedown 3: transversely over the eye of the coil.
  4. Forward restraint: blocking and bracing to prevent longitudinal movement in the forward direction.
CheckResultDetail
ScopeAppliesTotal weight 40,000 lb. Section 393.120 applies at 5,000 lb or more, individually or grouped together (section 393.120(a)).
Tiedown countPassThe pattern needs 3 tiedowns (393.120(b)(1)). You have 4 available.
Aggregate WLLCheckRequired 20,000 lb, half the total weight. The pattern provides 19,800 lb. Add 1 more tiedown, 4 in total. You have 4 available, so the extra tiedown are on hand.
Forward restraintPassBlocking and bracing to prevent longitudinal movement in the forward direction (section 393.120(b)(1)(iv)).

The figures

FigureValueNote
Tiedown3/8-in Grade 70 transport chain6,600 lb WLL each (section 393.108)
Total coil weight40,000 lb1 coil at 40,000 lb
Required aggregate WLL20,000 lbHalf the total weight (section 393.106(d))
Minimum tiedowns3Pattern in section 393.120(b)(1)
Tiedowns available4Enough for the pattern
Aggregate WLL of the pattern19,800 lbEach tiedown counts its full WLL (section 393.106(d)(3))
Extra tiedowns needed1To reach the required aggregate WLL

What to do

  • Add 1 more tiedown of the same type, 4 in total, placed through the eye or over the top per the pattern.
  • Re-check the load within the first 50 miles, then every 3 hours or 150 miles or at a duty-status change (section 392.9(b)).

Notes

  • Each tiedown in this pattern runs from an anchor point on one side, through or over the coil, to an anchor point on the other side, so each counts its full WLL toward the aggregate (section 393.106(d)(3)).
  • The WLL of a tiedown is the lowest WLL of any component, including the tensioner, or of the anchor points, whichever is less (section 393.108(a)). Manufacturer markings govern over the table values (section 393.108(b)).
  • Tiedowns must contain no knots and must be attached so they cannot come loose in transit (section 393.104(f)). Damaged tiedowns must not be used (section 393.104(b)).

This calculator applies 49 CFR 393.120 and 393.106(d) to your answers. Confirm the pattern against the current regulation and your company policy before you rely on a result.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.

Quick answer: Metal coils of 5,000 lb or more must be secured under 49 CFR 393.120. The pattern depends on which way the eye points. A coil with the eye vertical needs two diagonal tiedowns through the eye forming an X, one transverse tiedown over the eye, plus blocking and bracing, friction mats or tiedowns against forward movement. A coil with the eye crosswise needs anti-roll means that hold it off the deck plus one tiedown through the eye forward and one rearward. The X-pattern is prohibited for that position. A coil with the eye lengthwise has three options in the rule. Every pattern must also meet the aggregate working load limit: at least half the total coil weight. This calculator gives the pattern for one coil or one row. It checks the tiedown count and the aggregate WLL. It flags prohibited setups.

Last reviewed: · Focus keyword: metal coil securement

What does 49 CFR 393.120 require for metal coils?

Section 393.120 is the commodity-specific rule for metal coils in the FMCSA cargo securement rules. It applies to one or more metal coils that weigh 2,268 kg (5,000 lb) or more, individually or grouped together. Shipments under 5,000 lb may use the general securement rules in sections 393.100 through 393.114. The general rules are covered by the Flatbed Calculator.

The rule is organized by eye position, because a coil behaves differently in each position. A coil with the eye vertical can tip. A coil with the eye crosswise or lengthwise can roll. Each position gets its own section of the rule. The sections are not interchangeable. A pattern that is legal for one eye position can be prohibited for another: the X-pattern of diagonal tiedowns through the eye is required for a vertical eye and prohibited for a crosswise eye.

The rule also separates vehicles with anchor points from vehicles without them. Sections (b) to (d) cover flatbed vehicles, sided vehicles and intermodal containers with anchor points. Section (e) covers sided vehicles and intermodal containers without anchor points. In a vehicle with no anchor points there is no tiedown pattern to follow: the load must be arranged to prevent shifting and tipping, using blocking and bracing, friction mats, tiedowns or a combination.

One more rule sits underneath all of them. Section 393.106(d) requires the aggregate working load limit of the tiedowns to be at least half the weight of the cargo. A pattern can follow section 393.120 exactly and still fail if the tiedowns are too light for the weight. The calculator checks both the pattern and the aggregate WLL.

Eye positionSingle coil, minimum patternSection
Vertical2 diagonal tiedowns through the eye forming an X, 1 transverse tiedown over the eye, forward restraint393.120(b)(1)
CrosswiseAnti-roll means off the deck, 1 tiedown through the eye forward, 1 rearward, X-pattern prohibited393.120(c)(1)
Lengthwise, option 1Anti-roll means, 2 diagonal tiedowns through the eye, 1 transverse top tiedown, blocking or mats393.120(d)(1)
Lengthwise, option 2Anti-roll means, 2 straight tiedowns through the eye, 1 transverse top tiedown, blocking or mats393.120(d)(2)
Lengthwise, option 3Anti-roll means, 2 top tiedowns, blocking or mats393.120(d)(3)

How do you secure a metal coil with the eye vertical?

The eye vertical position is the one drivers call eye to the sky. The coil stands on its edge with the hole pointing up. It cannot roll, but it can tip forward, rearward or sideways under braking or cornering. Section 393.120(b)(1) sets the pattern for a single coil: two diagonal tiedowns through the eye, one from each side, crossing to form an X. One tiedown goes transversely over the eye. Blocking and bracing, friction mats or tiedowns prevent longitudinal movement in the forward direction.

Note what the section does not say. It sets no angle limit for the diagonal tiedowns on a single vertical-eye coil. The 45 degree limit appears in the rows paragraph and in the crosswise and lengthwise sections, not here. A steep diagonal on a single vertical-eye coil is not a violation of section 393.120(b)(1) by itself, although a tiedown that is too steep holds less well in practice.

Rows of vertical-eye coils follow section 393.120(b)(2). Each row needs one tiedown at the front restraining forward motion and one at the rear restraining rearward motion, each at an angle no more than 45 degrees with the floor whenever practicable. Each coil also needs one tiedown over the top restraining vertical motion, placed as close as practicable to the eye and positioned so it cannot slip or come unfastened in transit. One top tiedown may cover a whole transverse row. This calculator counts one top tiedown per coil, which always meets the rule.

The forward restraint in (b)(1)(iv) is the part drivers most often miss. The two diagonals and the transverse tiedown stop the coil from tipping. They do not by themselves stop the whole coil from sliding forward under hard braking. Blocking and bracing, friction mats or an extra tiedown must do that job. If you use tiedowns for the forward restraint, this calculator adds one tiedown to the minimum count.

How do you secure a metal coil with the eye crosswise?

A coil with the eye crosswise lies with the hole pointing across the trailer, from one side to the other. Drivers call this the suicide position, because a coil that breaks loose rolls forward toward the cab under braking. The regulation does not use that word. The rule for it is section 393.120(c). It starts with rolling, not with tiedowns.

Before any tiedown goes on, the coil needs a means to prevent rolling: timbers, chocks, wedges, a cradle or similar means. The means must support the coil off the deck. It must not be capable of becoming unintentionally unfastened or loose while the vehicle is in transit. Timbers, chocks or wedges must be held in place by coil bunks or similar devices to prevent them from coming loose.

Two anti-roll methods are prohibited outright. Nailed blocking or cleats cannot be the sole means to secure timbers, chocks or wedges. A nailed wood cradle cannot be the anti-roll means at all. Nails pull out under the forces a heavy coil applies in a hard stop. The rule was written after coils broke loose exactly that way. The calculator flags either method as a prohibited pattern.

Once the coil cannot roll, two tiedowns go through the eye: one restricting forward motion and one restricting rearward motion, each at an angle no more than 45 degrees with the floor whenever practicable. The diagonal X-pattern through the eye is prohibited for crosswise coils by section 393.120(c)(2). That ban surprises drivers who use the X on vertical-eye coils, where the same pattern is required. The difference is geometry: on a crosswise coil the diagonals pull the coil sideways and do nothing to stop a forward roll.

Section 393.120(c) states the rule for one coil at a time. It has no rows paragraph. In a row of crosswise coils, each coil needs its own anti-roll means and its own pair of through-eye tiedowns. The calculator applies the rule per coil and says so in the notes.

What are the three options for a coil with the eye lengthwise?

A coil with the eye lengthwise lies with the hole pointing along the trailer, from front to rear. Drivers call this the shotgun position. Like a crosswise coil it can roll, so every option starts with the same anti-roll means: timbers, chocks, wedges or a cradle supporting the coil off the deck, held by coil bunks or similar devices, with the same ban on nailed blocking or cleats as the sole means and on a nailed wood cradle.

Option 1, section 393.120(d)(1), is the closest to the vertical-eye pattern. Two tiedowns go diagonally through the eye, one from each side, forming an X, each at no more than 45 degrees whenever practicable. One tiedown goes transversely over the top of the coil. Blocking or friction mats prevent longitudinal movement. The X-pattern is allowed here. The ban in section 393.120(c)(2) covers crosswise eyes only.

Option 2, section 393.120(d)(2), replaces the diagonals with straight tiedowns through the eye: one on the left side running from near the front of the coil to near the rear. One on the right side runs the same way, each at no more than 45 degrees whenever practicable. One tiedown goes transversely over the top. Blocking or friction mats prevent longitudinal movement. Option 2 suits trailers where the anchor points do not line up for a diagonal run.

Option 3, section 393.120(d)(3), uses no through-eye tiedown at all. One tiedown goes over the top of the coil near the forward-most part and one near the rearmost part. Blocking or friction mats prevent longitudinal movement. Option 3 uses the fewest tiedowns, but it still needs the anti-roll means and the longitudinal restraint. The aggregate WLL check may still call for more tiedowns on a heavy coil.

Rows of lengthwise coils follow section 393.120(d)(4), which covers transverse rows of coils with approximately equal outside diameters. Each coil needs anti-roll means, one top tiedown near the front and one near the rear, plus blocking, bracing or friction mats against longitudinal movement. Note the wording change: the rows paragraph allows bracing, while options 1 to 3 allow blocking or friction mats only. Coils of different diameters do not fit the rows paragraph and need separate patterns. The FMCSA handbook describes a row as three or more coils loaded the same way in a line.

How many tiedowns does a metal coil need?

The minimum count comes from the pattern, not from a single number. A single vertical-eye coil needs 3 tiedowns, or 4 if tiedowns provide the forward restraint. A single crosswise coil needs 2. A single lengthwise coil needs 3 under option 1 or option 2. Option 3 needs 2. A row of vertical-eye coils needs 2 plus one per coil. A row of crosswise or lengthwise coils needs 2 per coil.

The minimum is only the start. The aggregate working load limit in section 393.106(d) can push the count higher. A 40,000 lb coil needs an aggregate WLL of 20,000 lb. Three 3/8-inch Grade 70 chains at 6,600 lb each provide 19,800 lb, which is 200 lb short. That load needs a fourth tiedown, or a heavier chain, even though the pattern minimum is 3. The calculator runs this check on every result and tells you how many extra tiedowns the WLL calls for.

Beware the four-chain claim that circulates on trucking blogs. Some pages state that every eye-to-the-sky coil needs four chains, each rated at one-eighth of the coil weight. They cite section 393.128. Section 393.128 covers automobiles, not coils. No one-eighth rule exists anywhere in Part 393. The regulation sets 3 tiedowns for a single vertical-eye coil and leaves the strength question to the aggregate WLL rule. Four chains may be the right answer for a heavy coil, but the reason is the WLL calculation, not a fixed count.

Heavy equipment has a different fixed count: section 393.130 requires at least four tiedowns for equipment of 10,000 lb or more. The Heavy Equipment Securement Calculator covers that rule. Do not carry its four-tiedown minimum over to coils. Do not carry a coil pattern over to equipment.

What is the aggregate working load limit for a coil load?

Section 393.106(d) requires the aggregate working load limit of the tiedowns used to secure an article or group of articles to be at least one-half times the weight of the article or group. For a single 40,000 lb coil the aggregate must be at least 20,000 lb. For a row, add the coil weights together first, then halve the total.

How much each tiedown counts depends on how it is attached. A tiedown that runs from an anchor point on the vehicle, through, over or around the cargo, to an anchor point on the other side of the vehicle counts its full WLL. A tiedown that runs from an anchor point to an anchor point on the cargo, or from an anchor point through or over the cargo back to an anchor point on the same side, counts half its WLL. Every tiedown in the section 393.120 coil patterns runs from one side to the other, so each one counts its full WLL. The calculator states this reading in the notes on every result.

The WLL of a tiedown comes from the manufacturer marking if the tiedown is marked, or from the tables in section 393.108 if it is not. Marked values govern: if a chain is marked with a WLL that differs from the table, the marked value applies. The WLL of a tiedown assembly is the lowest WLL of any component, including the tensioner, or of the anchor points, whichever is less. A 6,600 lb chain on a 5,000 lb anchor point is a 5,000 lb tiedown. The Flatbed Calculator carries the full section 393.108 tables.

TiedownWLL (lb)Source
3/8-in Grade 70 transport chain6,600393.108 chain table
1/2-in Grade 70 transport chain11,300393.108 chain table
5/16-in Grade 70 transport chain4,700393.108 chain table
3/8-in Grade 43 high-test chain5,400393.108 chain table
4-in synthetic webbing4,000393.108 webbing table
3-in synthetic webbing3,000393.108 webbing table
2-in synthetic webbing2,000393.108 webbing table
1/2-in wire rope, 6 x 37 fiber core5,300393.108 wire rope table

Logs are the one commodity where the aggregate fraction differs: section 393.116 sets the aggregate WLL for a log stack at one-sixth of the stack weight, not one-half. The Log Securement Calculator covers that rule. Do not carry the one-sixth figure over to coils.

Why is nailed blocking prohibited as the only anti-roll means?

A steel coil is a dense, round weight that wants to roll. On a flatbed it sits on a small contact patch. Under hard braking the forward force on a 40,000 lb coil is enormous. The anti-roll means must hold that force without shifting. It must keep holding it for the whole trip.

Nails fail that test. A nail driven through blocking into a wood deck holds by friction in a small hole. Vibration works it loose. One hard stop can pull a row of nails straight out of the deck. Once the blocking moves the coil is free to roll. The rule does not ban nails entirely: nailed blocking may still be part of a system. What the rule bans is nailed blocking or cleats as the sole means to secure the timbers, chocks or wedges. It also bans a nailed wood cradle as the anti-roll means.

Coil bunks are the approved answer. A coil bunk is a steel or hardwood frame that cradles the coil and holds the chocks or timbers in place mechanically, so the chocks cannot slide or lift out. The bunk itself is secured to the trailer. A steel cradle works the same way. Either one keeps the coil supported off the deck, which the rule requires. It also keeps the anti-roll means from coming loose in transit.

The same ban appears in every part of the rule that calls for anti-roll means: crosswise coils in section 393.120(c)(1)(i), lengthwise coils in section 393.120(d)(1) to (d)(4). If a shipper loads a coil onto nailed cribbing and calls it done, the load is not compliant. The driver is the one who answers for it at the scale.

How do you secure coils in a vehicle with no anchor points?

Some sided vehicles and intermodal containers have no anchor points at all. Sections 393.120(b) to (d) all assume anchor points exist, so none of those patterns apply. Section 393.120(e) covers the case in one paragraph: the coils must be loaded in a manner to prevent shifting and tipping. They may also be secured using blocking and bracing, friction mats, tiedowns or a combination of these to prevent any horizontal movement and tipping.

In practice that means loading the coils tight against the sides and against each other, with blocking and bracing filling the gaps and friction mats under the coils. A coil that can roll still needs chocks or a cradle: section 393.106(c)(1) requires articles likely to roll to be restrained by chocks, wedges, a cradle or equivalent means. That requirement applies to all cargo.

Section 393.120(e) sets no tiedown count, no angle limit and no named pattern. The test is the outcome: the load must not shift, tip or move horizontally. An inspector judges the load as loaded, so the blocking and bracing must be solid enough to convince a stranger at the roadside, not just the loader who built it.

Containers have their own securement rule for the container itself: section 393.126 governs how an intermodal container is secured to its chassis, including the corner fittings and the movement limits. The Intermodal Container Securement Calculator covers that side of the load.

How do you use the Metal Coil Securement Calculator?

Enter the load, pick the pattern, read the checks. The calculator updates with every change, so you can try a heavier chain or a different eye position and watch the verdict change.

  1. Enter the weight of one coil in pounds.
  2. Pick single coil or a row of coils. Enter the number of coils in the row.
  3. Pick the eye position: vertical, crosswise or lengthwise. For a single lengthwise coil, pick option 1, 2 or 3.
  4. Pick the vehicle type and the tiedown type, then enter how many tiedowns are available.
  5. Pick the anti-roll means and the forward restraint fitted on the load. Enter the steepest tiedown angle if you know it.
  6. Read the pattern, the checks and the actions. Fix every failed check before you roll, then re-check the load within the first 50 miles.

Before you roll, run the Pre-Trip Inspection Checklist as well. Cargo securement is part of the pre-trip inspection. A tiedown problem found in the yard is cheaper than one found at a scale.

Frequently asked questions

How many tiedowns are required for a metal coil?

It depends on the eye position. A single coil with the eye vertical needs 3 tiedowns: two diagonal tiedowns through the eye forming an X plus one transverse tiedown over the eye. A single coil with the eye crosswise needs 2 tiedowns through the eye, one forward and one rearward, plus anti-roll means. A single coil with the eye lengthwise needs 3 tiedowns under option 1 or option 2, or 2 under option 3, plus anti-roll means and blocking or friction mats. The aggregate working load limit may call for more tiedowns on a heavy coil.

What is the minimum weight for the metal coil rule?

Section 393.120 applies to metal coils that weigh 5,000 lb or more, individually or grouped together. Shipments under 5,000 lb may be secured under the general rules in sections 393.100 through 393.114. Two 3,000 lb coils grouped together weigh 6,000 lb, so the commodity rule applies to the group.

Can you use an X-pattern on a coil with the eye crosswise?

No. Section 393.120(c)(2) prohibits attaching tiedowns diagonally through the eye of a coil to form an X-pattern when the eye is crosswise. The X-pattern is required for a vertical eye and allowed under option 1 for a lengthwise eye. The ban covers crosswise eyes only.

Can you use nailed blocking to stop a coil from rolling?

Not as the only means. Section 393.120 prohibits nailed blocking or cleats as the sole means to secure timbers, chocks or wedges. It also prohibits a nailed wood cradle. Use coil bunks with timbers, chocks or wedges, or a cradle held so it cannot come loose, supporting the coil off the deck.

What angle must coil tiedowns make with the floor?

For rows of vertical-eye coils, crosswise coils and lengthwise coils, the tiedowns must make an angle no more than 45 degrees with the floor of the vehicle whenever practicable, measured from the side. The single vertical-eye coil pattern in section 393.120(b)(1) sets no angle limit.

How often must a driver re-check coil securement?

Section 392.9(b) requires the driver to inspect the cargo and the securement devices within the first 50 miles after beginning a trip, then reexamine them whenever the driver changes duty status, or the vehicle has been driven 3 hours, or 150 miles, whichever occurs first. The driver must make adjustments as necessary, including adding more securement devices.

Related tools

Sources

Follow on WhatsApp Ask by Voice