One container at a time. This checker runs one intermodal container against the securement rule in 49 CFR 393.126, plus the pre-trip inspection in 49 CFR 392.7(b). A result that says fix means the container must not roll until the securement is fixed.
Pick loaded or empty, pick the vehicle, enter what you see at the corners. Every answer updates as you change each field.
The container and the vehicle
On a container chassis
Push the container forward, aft, left and right at a corner and measure the play. Lift it to measure the vertical play. Leave a field blank if you have not measured it.
How the container is held
On a vehicle other than a chassis, loaded
On a vehicle other than a chassis, empty
Overhang
Measure from the end of the vehicle deck to the end of the container. Enter 0 if the container does not overhang at that end.
Pre-trip inspection
Check before you roll
The securement meets the rule, with checks on Pre-trip inspection.
| Check | Result | Detail |
|---|---|---|
| Lower corners locked | Pass | All four lower corners are secured to the chassis with securement devices or integral locking devices (49 CFR 393.126(b)(1)). |
| Devices stay fastened | Pass | The securement devices cannot unintentionally become unfastened while the vehicle is in transit (49 CFR 393.126(b)(1)). |
| Horizontal movement | Pass | 0.25 in. Within the half-inch limit forward, aft, left and right (49 CFR 393.126(b)(2)). |
| Vertical movement | Pass | 0.5 in. Within the one-inch vertical limit (49 CFR 393.126(b)(2)). |
| Front and rear secured independently | Pass | The front and rear of the container are secured independently, so a failure at one end does not free the other (49 CFR 393.126(b)(3)). |
| Pre-trip inspection | Check | Before the equipment moves over the road, inspect the nine components in 49 CFR 392.7(b) and be satisfied they are in good working order. A driver who operates the equipment is deemed to have confirmed them. |
The figures
| Figure | Value | Note |
|---|---|---|
| Container length | 40 ft | As entered |
| Load status | Loaded | Cargo inside follows 49 CFR 393.100 through 393.114 |
| Vehicle | Container chassis | 49 CFR 393.126(b) applies, loaded or empty |
| Horizontal movement | 0.25 in | Limit 1/2 in |
| Vertical movement | 0.5 in | Limit 1 in |
What to do
- Walk the nine components in 49 CFR 392.7(b) before the equipment moves over the road.
Notes
- Cargo inside the container must be secured under the general rules in 49 CFR 393.100 through 393.114 or the commodity rule for the cargo (49 CFR 393.126(a)). This checker covers the container, not the cargo inside it.
- Inspect the cargo and the securement devices within the first 50 miles of the trip and reexamine them at every duty status change, after 3 hours of driving or after 150 miles, whichever comes first (49 CFR 392.9(b)).
- Twist locks and integral locking devices must be fully engaged. A lock that is only half turned can work loose under vibration.
- The nine components in 49 CFR 392.7(b): Service brake components visible without going under the vehicle plus trailer brake connections; lighting devices, lamps, markers and conspicuity marking material; wheels, rims, lugs and tires; air line connections, hoses and couplers; king pin upper coupling device; rails or support frames; tie down bolsters; locking pins, clevises, clamps or hooks; sliders or sliding frame lock.
This checker applies 49 CFR 393.126 and 49 CFR 392.7(b) to your answers. Confirm the measurements with a tape before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice. Check the current regulation and your company policy before you rely on a result.
Quick answer: A container on a chassis needs all four lower corners locked with devices that cannot work loose, movement held to half an inch sideways and one inch up, with the front and rear held independently. A loaded container on any other vehicle needs every lower corner resting on the deck or on a secured support structure, plus chains or wire ropes on all lower corners or crossed chains on all upper corners. An empty container on any other vehicle may overhang up to five feet at either end if it sits balanced and stable, clears the maneuvering of the vehicle and is tied against shifting. This checker runs your setup against 49 CFR 393.126 and the nine-point inspection in 49 CFR 392.7(b).
What does 49 CFR 393.126 require for intermodal containers?
One short section of the cargo securement rules covers every intermodal container on the road. Section 393.126 of Title 49 sets the securement standard in three parts. Which part applies turns on two facts: whether the container rides on a container chassis or on some other vehicle and whether it is loaded or empty. The checker on this page asks those two questions first because they decide everything that follows.
The section opens with a point drivers sometimes miss. The rule for the container is separate from the rule for the cargo inside it. Cargo inside an intermodal container must be secured under the general rules in 49 CFR 393.100 through 393.114 or under the commodity rule for that cargo, whichever applies. A sealed box does not excuse loose freight inside it. The container rule in 393.126 covers how the box itself is held to the vehicle. This checker covers the box. For the freight inside, the Flatbed Calculator carries the general securement rules and the Working Load Limit tables for the tiedowns.
| Configuration | Governing paragraph | Headline requirement |
|---|---|---|
| Any container on a container chassis, loaded or empty | 49 CFR 393.126(b) | All lower corners locked; movement held to 1/2 in sideways and 1 in up; front and rear independent |
| Loaded container on a vehicle other than a chassis | 49 CFR 393.126(c) | All lower corners resting on the vehicle or on a secured support structure; chains, wire ropes or integral devices on all lower corners, or crossed chains on all upper corners |
| Empty container on a vehicle other than a chassis | 49 CFR 393.126(d) | Balanced and stable before tiedowns; overhang 5 ft or less at either end; no interference with maneuverability; secured against shifting |
Two traps sit in that table. First, the empty-container relaxation in paragraph (d) applies only on a vehicle other than a container chassis. An empty box on a chassis follows the same rule as a loaded one: all four corners locked, movement held to the same half-inch and one-inch limits. Second, the three paragraphs are alternatives, not a menu. A loaded container on a flatbed cannot borrow the empty-container overhang allowance. An empty container on a flatbed cannot skip the four conditions in paragraph (d) by pointing at the chassis rule.
The rule has been stable for a long time. Section 393.126 dates to the cargo securement rulemaking of 2002 and was last amended in 2006. The figures in this checker were verified against the current text of the regulation on November 19, 2026. The last reviewed line at the top of this page shows when that check was made.
How must a container be secured on a container chassis?
Most intermodal moves ride on a container chassis, so paragraph (b) is the rule most drayage drivers live with. It sets three requirements and all three must hold at once.
First, all lower corners of the container must be secured to the chassis with securement devices or integral locking devices that cannot unintentionally become unfastened while the vehicle is in transit. On a standard chassis those devices are twist locks: the corner casting of the container drops over the lock, the handle turns and the head holds the casting down. A twist lock that is only half turned is not secured. A lock with a worn head, a bent handle or a missing spring can work loose under vibration. A device that can work loose fails the rule even if it is holding at the moment of inspection.
Second, the securement devices must restrain the container from moving more than half an inch forward, more than half an inch aft, more than half an inch to the right, more than half an inch to the left, or more than one inch vertically. The regulation states the limits in metric first, 1.27 cm and 2.54 cm, with the inch figures beside them. The horizontal limit is tighter than the vertical one because a container that can slide sideways or lengthways can walk off its locks.
Measure the play at the corners with a tape: push the box in each direction, then lift it. If the movement is over the limit, tighten or replace the devices and measure again. The checker takes your measured numbers and tests them against both limits.
Third, the front and rear of the container must be secured independently. One device holding both ends does not meet the rule. The point is redundancy: a failure at one end must not free the other end. On a chassis this usually follows naturally from four separate twist locks, but the rule still has to be checked when a lock is missing or when a makeshift device spans the box.
Paragraph (b) applies to loaded and empty containers alike. An empty 40 ft box still weighs around 8,000 lb and still leaves the chassis the same way a loaded one does if the locks fail. The empty-container relaxation in paragraph (d) never applies on a chassis, so do not let an empty move tempt you into skipping a corner.
How do you secure a loaded container on a flatbed or other vehicle?
A loaded container on a flatbed, a step deck or any vehicle that is not a container chassis falls under paragraph (c). The rule there works differently. There are no twist locks to drop the box onto, so the regulation builds the securement from two separate duties: support and tiedowns.
The support duty comes first. All lower corners of the container must rest upon the vehicle, or the corners must be supported by a structure capable of bearing the weight of the container. That support structure must be independently secured to the motor vehicle. A corner hanging past the end of the deck is not resting on the vehicle. If the container overhangs, the overhanging corner needs a support structure under it. That structure needs its own securement to the vehicle. Blocking that merely sits under the corner without being secured does not meet the rule. The checker tests this: tell it the overhang at each end and how the corners are supported. It will flag a corner that hangs in the air.
The tiedown duty gives two methods and either one meets the rule. The container must be secured by chains, wire ropes or integral devices which are fixed to all lower corners, or by crossed chains which are fixed to all upper corners. Note what is not on that list. Synthetic webbing is not listed as a method in paragraph (c)(2) at all. A web strap over the box is not one of the two methods the regulation names. Use chains or wire ropes of known Working Load Limit. Check the rating before you trust it: the Flatbed Calculator carries the full Working Load Limit tables for chains, wire ropes, webbing and strapping.
Paragraph (c) closes with the same two safeguards as the chassis rule. The front and rear of the container must be secured independently. Each chain, wire rope, or integral locking device must be attached to the container in a manner that prevents it from being unintentionally unfastened while the vehicle is in transit. A hook that can bounce out of a corner casting under vibration fails that test even if it is tight when you set it.
Do not confuse this rule with the roll-off rule. A roll-off or hook-lift container is a different piece of equipment with its own section, 49 CFR 393.134, with its own securement pattern. If the box on the truck is a roll-off container, use the Roll-Off and Hook-Lift Container Securement Calculator instead of this one.
What are the rules for an empty container on a non-chassis vehicle?
Paragraph (d) is the one relaxation in the section. It is narrow. An empty container on a vehicle other than a container chassis does not have to have all lower corners resting upon the vehicle, or all lower corners supported by a structure capable of bearing the weight of the empty container, provided four conditions are all met. Miss one and the relaxation is gone: the container falls back to the full lower-corner support rule in paragraph (c).
First, the empty container must be balanced and positioned on the vehicle in a manner such that the container is stable before the addition of tiedowns or other securement equipment. Stable before tiedowns is the key phrase. Tiedowns hold a stable load in place. They do not make an unstable load stable. If the box rocks or tips when the tiedowns come off, it is not balanced and positioned correctly. The empty-container rule does not apply.
Second, the amount of overhang for the empty container on the trailer must not exceed five feet on either the front or rear of the trailer. The cap applies to each end separately. Five feet at the front and five feet at the rear is within the rule. Six feet at one end is not, even if the other end has no overhang at all. The next section works through the measurement.
Third, the empty container must not interfere with the maneuverability of the vehicle. An overhang that swings wide on a turn, blocks the view of a lamp or fouls the landing gear fails this condition even if the tape measure says five feet. The test is practical: does the vehicle still turn, clear and stop the way it should with the box where it sits.
Fourth, the empty container must be secured to prevent lateral, longitudinal, or vertical shifting. The relaxation in paragraph (d) is about support, not about securement. The box still needs tiedowns or other securement equipment that hold it against movement in every direction. An empty box that merely rests on the deck, however stable it looks, is not secured.
Remember the scope limit. Paragraph (d) applies only to empty containers on vehicles other than container chassis vehicles. An empty container on a chassis follows paragraph (b) with no relaxation at all.
What is the 5-foot overhang rule for empty containers?
The five-foot figure in paragraph (d)(2) is the most quoted number in the empty-container rule and the easiest to misread. The regulation caps the overhang at each end of the trailer, not the total. Measure the front overhang from the front end of the vehicle deck to the front end of the container. Measure the rear overhang the same way at the back. Each number must be five feet or less.
A centered load shows how the arithmetic works. A 40 ft empty container on a 30 ft deck overhangs five feet at the front and five feet at the rear if it sits centered. That passes. Slide the same box two feet forward and the front overhang becomes seven feet while the rear drops to three. The total overhang is unchanged at ten feet, but the move now fails the rule at the front. Centering is not just neatness. It is how a long box stays inside a per-end limit.
Measure with a tape, not by eye. The difference between five feet and five feet six inches is hard to judge from the ground. The rule has no tolerance for a near miss. Measure at the deck, not at the rub rail or the stake pocket, because the regulation measures the overhang on the trailer. If either end reads over five feet, slide the container toward the short end until both ends read five feet or less, then check the balance again: sliding the box changes where its weight sits. The first condition in paragraph (d) still has to hold.
Overhang also feeds the other two conditions. A long rear overhang swings wider on turns and can clip a curb, a sign or a vehicle in the next lane. A long front overhang can foul the tractor or the headache rack. If the overhang interferes with maneuverability, the move fails paragraph (d)(3) even with both ends inside five feet. And an overhanging box needs its tiedowns placed so the unsupported end cannot bounce: a tiedown at the very end of the deck does little for a corner that hangs five feet past it.
The checker tests each end separately. Enter the front and rear overhang and it will pass or fail each one against the five-foot limit, then test the other three conditions in paragraph (d) alongside.
What must a driver inspect before pulling intermodal equipment?
Securement is only half the job at the terminal. Before intermodal equipment moves over the road, the driver accepting the equipment must inspect the components listed in 49 CFR 392.7(b) and be satisfied they are in good working order. Section 390.42(a) states the duty in the same terms. The list has nine items. It is the same list the driver reports against when the equipment goes back to the provider under 49 CFR 396.11(b).
| # | Component in 49 CFR 392.7(b) | What to look for |
|---|---|---|
| 1 | Service brake components readily visible without going under the vehicle, plus trailer brake connections | Chambers, hoses and connections in place, no audible leaks, no missing parts |
| 2 | Lighting devices, lamps, markers and conspicuity marking material | Every lamp lit, markers in place, reflective tape present and clean |
| 3 | Wheels, rims, lugs, tires | Lug nuts tight, no cracks in rims, tires inflated with legal tread |
| 4 | Air line connections, hoses and couplers | Gladhands seated, hoses undamaged, no chafing or kinks |
| 5 | King pin upper coupling device | King pin undamaged, upper coupler plate sound, fifth wheel jaws closed on it |
| 6 | Rails or support frames | No cracks, bends or broken welds in the chassis rails |
| 7 | Tie down bolsters | Bolsters sound, twist lock pockets undamaged |
| 8 | Locking pins, clevises, clamps, or hooks | Twist locks turn fully and hold, pins present, no worn or bent parts |
| 9 | Sliders or sliding frame lock | Slider pins engaged, frame locked in position |
The rule carries a sting. A driver who operates the equipment over the road is deemed to have confirmed the components were in good working order when the driver accepted the equipment. That deeming clause means the inspection cannot be skipped and blamed on the terminal later. If a brake chamber is visibly damaged at pickup and the driver pulls out anyway, the driver owns that defect at the roadside.
The inspection duty runs both ways. When the equipment is returned, the driver or motor carrier must report any known damage, defects, or deficiencies to the intermodal equipment provider or its designated agent, under 49 CFR 396.11(b). The report covers the same nine components and must name the carrier, both USDOT numbers, the equipment identifier, the date and time and the defects found. The provider must repair reported defects that are likely to affect the safety of operation before the equipment goes out again. The DVIR Checker walks through the driver vehicle inspection report. The Pre-Trip Inspection Checklist covers the full walk-around with out-of-service flags.
The checker treats the nine-component inspection as a check to complete, not as a securement pass or fail. A container can be perfectly locked to a chassis with a cracked rail underneath it. The pre-trip question stays open until you confirm the inspection is done.
How often must cargo securement be rechecked on the road?
Securing the container at the terminal is the start, not the end. Section 392.9(b) sets a recheck schedule that runs for the whole trip. It applies to the devices that hold the container as well as to the cargo inside it.
Before driving, the driver must be satisfied that the cargo is properly distributed and adequately secured, that the tailgate, doors, tarpaulins and fastening equipment are secured and that nothing obscures the view or blocks access to emergency equipment. Within the first 50 miles after beginning a trip, the driver must inspect the cargo and the devices used to secure the cargo and cause any adjustments to be made, including adding more securement devices, so the cargo cannot shift on or within the vehicle or fall from it. The first 50 miles matter because that is when a load settles: chains stretch, twist locks seat and a corner that looked tight at the dock can show play after the first stretch of rough road.
After that first check, the driver must reexamine the cargo and its load securement devices during the course of transportation and make any necessary adjustment whenever the driver makes a change of duty status, whenever the vehicle has been driven for 3 hours, or whenever the vehicle has been driven for 150 miles, whichever occurs first. On a long day the 3-hour trigger usually comes first. On a short-hop drayage day the duty status change at each terminal stop is the trigger that matters. Either way, the recheck is not optional and it is not satisfied by a glance in the mirror: the rule calls for reexamination of the cargo and the devices, with adjustments made as necessary.
One exception exists. The rules in paragraph (b) do not apply to the driver of a sealed commercial motor vehicle who has been ordered not to open it to inspect its cargo, or to the driver of a vehicle loaded in a manner that makes inspection of its cargo impracticable. The exception is about cargo the driver cannot reach. The twist locks and chains that hold the container to the vehicle are outside the box, so they stay on the check list at every stop. A sealed container still needs its corners checked at 50 miles and at every recheck point after that.
What happens if a container is not secured to the rule?
A container that does not meet 49 CFR 393.126 is a violation. The consequences run past a ticket. Under 49 CFR 396.9(c), authorized personnel shall declare and mark out of service any motor vehicle or intermodal equipment which by reason of its mechanical condition or loading would likely cause an accident or a breakdown. A container that can slide half an inch past its limit, or a corner left unlocked, is exactly the kind of loading defect that supports an out-of-service order.
Once the sticker goes on, no person may operate the vehicle or the intermodal equipment until all repairs required by the out-of-service notice have been satisfactorily completed. No person may remove the sticker before those repairs are done. Towing the vehicle away is itself treated as operating it, unless the tow uses a crane or hoist.
The paperwork follows the driver home. A driver who receives an inspection report must deliver a copy to both the motor carrier operating the vehicle and the intermodal equipment provider upon arrival at the next terminal or facility. If the driver is not scheduled to reach a terminal or a provider facility within 24 hours, the report must be mailed or otherwise transmitted at once. The carrier and the provider must examine the report and correct the violations or defects noted on it. A loose container is therefore not a problem that ends at the scale house. It travels back to the carrier and to the equipment provider in writing.
The tiedowns themselves deserve a final note. A damaged tiedown is a violation. It does not count toward the tiedown count or toward the aggregate Working Load Limit. A chain with a stretched link or a wire rope with a broken strand cannot be counted as one of the devices securing the container under paragraph (c)(2). If the only chain on a corner is damaged, that corner is unsecured for the purposes of the rule, whatever the chain looks like from a distance. Check each device before you count it.
How do you use the Intermodal Container Securement Calculator?
- Pick loaded or empty, then pick the vehicle: a container chassis or a flatbed or other vehicle.
- Enter the container length in feet. Standard boxes run 20 ft, 40 ft, 45 ft, 48 ft and 53 ft.
- On a chassis, answer the corner questions and measure the movement at the corners: push the container forward, aft, left and right, then lift it. The limits are half an inch sideways and one inch up.
- On any other vehicle, enter the front and rear overhang in feet and answer the support and securement questions for a loaded container, or the four empty-container questions for an empty one.
- Answer the pre-trip question. The checker counts the nine-component inspection in 49 CFR 392.7(b) as a check to complete before the equipment moves.
- Read the verdict, the check table, the figures and the notes. Copy the summary for the trip records, or reset the checker to start over.
Frequently asked questions
How much can an intermodal container move on a chassis?
On a container chassis the securement devices must hold the container to half an inch or less forward, aft, left and right, plus one inch or less vertically. The limits are in 49 CFR 393.126(b)(2) and they apply to loaded and empty containers alike. Measure the play at the corners with a tape before you roll.
Do all four lower corners have to be locked on a chassis?
Yes. Every lower corner of the container must be secured to the chassis with a securement device or an integral locking device that cannot unintentionally become unfastened while the vehicle is in transit. The front and rear must be secured independently, so a failure at one end does not free the other. The rule is 49 CFR 393.126(b)(1) and (b)(3).
Can an empty container overhang the trailer?
Yes, on a vehicle other than a container chassis. The overhang must not exceed five feet at the front or at the rear. The empty container must be balanced and stable before tiedowns go on, must not interfere with the maneuverability of the vehicle and must be secured against lateral, longitudinal, or vertical shifting. All four conditions in 49 CFR 393.126(d) must hold at once. An empty container on a chassis gets no overhang allowance.
What is the nine-point intermodal inspection?
Before intermodal equipment moves over the road, the driver must inspect nine components and be satisfied they are in good working order: service brake components visible without going under the vehicle plus trailer brake connections; lighting devices, lamps, markers and conspicuity marking material; wheels, rims, lugs and tires; air line connections, hoses and couplers; king pin upper coupling device; rails or support frames; tie down bolsters; locking pins, clevises, clamps or hooks; sliders or sliding frame lock. The list is in 49 CFR 392.7(b). A driver who operates the equipment is deemed to have confirmed them.
Who fixes a defect found on intermodal equipment?
The driver reports known damage, defects, or deficiencies to the intermodal equipment provider when the equipment is returned, under 49 CFR 396.11(b). The provider must repair reported defects that are likely to affect the safety of operation before the equipment goes out again. Before the trip, the driver must inspect the nine components in 49 CFR 392.7(b) and be satisfied they are in good working order. The driver must not operate equipment with a defect in those components.
Does the cargo inside a sealed container need securement?
Yes. Cargo inside an intermodal container must be secured under the general rules in 49 CFR 393.100 through 393.114 or the commodity rule for the cargo, under 49 CFR 393.126(a). A driver who has been ordered not to open a sealed vehicle is excused from inspecting the cargo inside under 49 CFR 392.9(b)(4), but the devices that hold the container to the vehicle are outside the box and stay on the check list.
Related tools
- Roll-Off and Hook-Lift Container Securement Calculator: roll-off and hook-lift boxes follow a different rule, 49 CFR 393.134.
- Flatbed Calculator: Working Load Limit tables for chains, wire ropes and webbing, plus the general cargo securement rules.
- DVIR Checker: the driver vehicle inspection report for the equipment, including the intermodal report at return.
- Pre-Trip Inspection Checklist: the full pre-trip walk-around, with out-of-service flags.
- Heavy Equipment Securement Calculator: machinery and vehicles over 10,000 lb follow 49 CFR 393.130.
- Metal Coil Securement Calculator: coils over 5,000 lb follow 49 CFR 393.120.
Sources
- 49 CFR 393.126: Specific securement requirements for intermodal containers (Cornell LII, read Nov 19, 2026)
- 49 CFR 392.7: Equipment, inspection and use (Cornell LII, read Nov 19, 2026)
- 49 CFR 392.9: Inspection of cargo, cargo securement devices and systems (Cornell LII, read Nov 19, 2026)
- 49 CFR 396.11: Driver vehicle inspection report(s) (Cornell LII, read Nov 19, 2026)
- 49 CFR 396.9: Inspection of motor vehicles and intermodal equipment in operation (eCFR.io, read Nov 19, 2026)
- 49 CFR 390.40T and 390.42: Intermodal equipment providers and drivers (govinfo, CFR-2025, read Nov 19, 2026)
- 49 CFR 393.126 cross-check (eCFR.io, read Nov 19, 2026)