An out-of-service condition parks the vehicle. This checker applies 49 CFR 393.207, Appendix G item 8 plus the CVSA out-of-service criteria to the defects you enter. An out-of-service result means the vehicle must not move until repairs are complete. A violation result means the defect must be fixed plus reported, even though the vehicle is not parked.
Tick every defect you found on the walk-around, then enter the leaf count, the locking pin count, plus the two air test figures. Every answer updates the result as you change each field. Leave a box unticked when that part is sound.
About the suspension
A tractor often has leaf springs on the steer axle plus air suspension on the drives. Run the check once per axle when the axles differ, or tick the defects from every axle in one run.
Axle and axle positioning parts
Leaf springs
Count the leaves in the worst spring assembly, then count the broken ones in that same assembly. One-fourth or more broken is out of service. Any broken leaf fails the annual inspection.
Coil, rubber, torsion and composite springs
Tracking components, bushings and shock absorbers
Sliding tandem locking pins
More than one-fourth of the locking pins missing or disengaged is out of service. Any pin missing or not engaged fails the annual inspection. Enter zero total pins when the vehicle has no adjustable axle.
Air suspension
Run the leak test with the gauge at normal operating pressure and the brakes released. Watch the gauge for 5 minutes and enter the pressure lost.
Violation found. Not out of service.
1 violation found, no out-of-service conditions.
No condition here meets the CVSA out-of-service criteria, so the vehicle is not parked at the roadside. Each violation still counts against the carrier in the Vehicle Maintenance BASIC at severity weight 7, plus each annual inspection failure must be fixed before the vehicle can pass its next periodic inspection. Report every defect to the carrier and get it repaired.
The checks
| Check | Result | Detail |
|---|---|---|
| U-bolts and spring clamp bolts | Pass | No U-bolt or clamp bolt defect reported. |
| Axle positioning parts and axle shift | Pass | No axle shift from a failed positioning part reported. |
| Axle alignment | Pass | Axles reported in proper alignment. |
| Leaf springs, broken count | Violation | 2 of 10 leaves broken is 20.0 percent, below the 25 percent out-of-service line. Any broken leaf is still a violation under section 393.207(c) plus an annual inspection failure under Appendix G item 8.b(1). |
| Main leaf | Pass | No broken main leaf reported. |
| Leaf missing or separated | Pass | No leaf missing or separated. |
| Leaf displaced toward tire or frame | Pass | No leaf displaced toward a tire, rim, brake drum or frame. |
| Leaf cracked, not broken | Pass | No cracked leaf reported. |
| Leaf spring shifted out of position | Pass | Leaf springs reported in position. |
| Coil spring | Pass | No coil spring defect reported. |
| Rubber spring | Pass | No rubber spring missing. |
| Torsion bar spring | Pass | No torsion bar defect reported. |
| Composite spring | Pass | No composite spring crack reported. |
| Torque, radius and tracking components | Pass | No tracking component defect reported. |
| Torque and track rod bushings | Pass | Bushings reported sound. |
| Shock absorber | Pass | No shock absorber defect reported. |
| Sliding tandem locking pins | Pass | All locking pins engaged. |
| Sliding suspension locking component | Pass | Locking component reported sound. |
| Air suspension leak test | Pass | 2.0 psi lost in 5 minutes, within the 3 psi limit in section 393.207(f). |
| Air pressure regulator | Pass | Air reaches the suspension at 60 psi, at or above the 55 psi line in section 393.207(f). |
| Vehicle level at normal pressure | Pass | Vehicle reported level at normal operating pressure. |
| Air spring and bag condition | Pass | No air bag defect reported. |
| Air leak heard at bag, line or fitting | Pass | No air leak heard or found. |
| Air suspension exhaust controls | Not applicable | No two-axle air suspension trailer exhaust controls entered. Section 393.207(g) applies to two-axle air suspension trailers only. |
The figures
| Figure | Value | Note |
|---|---|---|
| Out-of-service conditions | 0 | Each one parks the vehicle until repaired, under section 396.9(c)(2). |
| Section 393.207 violations | 1 | Severity weight 7 each in the Vehicle Maintenance BASIC. An out-of-service condition adds 2. |
| Annual inspection | Would fail | 1 suspension item fail the periodic inspection standard in Appendix G to Subchapter B, item 8, plus item 9.c(1) for locking pins. |
| Leaves broken | 2 of 10 (20.0%) | One-fourth or more broken is out of service. Any broken leaf fails the annual inspection. |
| Air leak test | 2.0 psi in 5 minutes | Section 393.207(f) allows no more than 3 psi in 5 minutes at normal operating pressure. |
| Regulator cut-in | 60 psi | The regulator must hold air back until at least 55 psi is in the braking system. |
| Locking pins | 0 of 4 missing or disengaged | More than one-fourth missing or disengaged is out of service. Any pin fails the annual inspection. |
What to do
- Replace the broken leaves or the full spring assembly. A spring shop should match the pack.
- Report each defect to the carrier and get it repaired before the next periodic inspection.
What would clear the verdict
- Repair Leaf springs, broken count: removes 1 violation.
Notes
- Three tiers decide the result. Section 393.207 sets the violation line. Appendix G item 8 sets the annual inspection line. The CVSA out-of-service criteria set the roadside line. A defect can sit on one line without reaching the next.
- A loose U-bolt with no axle shift parks the vehicle at the roadside under CVSA Part II item 11.a, but Appendix G item 8.a fails the annual inspection only when a failed part lets the axle shift. The roadside line is tighter than the annual line here.
- A cracked leaf, coil or torsion bar is a section 393.207 violation. Appendix G item 8 lists broken or missing parts only, so a crack alone does not fail the annual inspection on the letter of the standard.
- The 55 psi regulator rule and the low-air warning device share a number but not a device. The regulator is a pressure protection valve on the suspension supply. The warning device is a cab alarm under Appendix G item 1.f.
- Ride height has no federal number. The manufacturer sets it. The federal test is the level test in section 393.207(f): the vehicle must not tilt left or right at normal operating pressure.
- Suspension is not one of the 11 parts on the driver vehicle inspection report list in sections 392.7 and 396.11. Section 396.13 still requires the driver to be satisfied the vehicle is safe before driving, plus section 396.7 bars operating a vehicle in a condition likely to cause an accident or a breakdown.
- The 2026 CVSA out-of-service criteria, effective April 1, 2026, made 17 changes. None of them touched suspension, so the lines in this tool carry forward unchanged.
- After a turn, lateral axle displacement is normal on some suspensions. Driving forward or backward in a straight line brings the axle back to alignment. That movement alone is not a defect.
This tool applies 49 CFR 393.207, Appendix G item 8 plus the CVSA out-of-service criteria to your inputs. The inspector decides the roadside result. Confirm the result against the regulation plus your maintenance records before acting.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is a planning estimate based on the published regulation plus the CVSA criteria, not legal advice — confirm the result with a qualified inspector or your legal counsel before acting on an out-of-service decision.
Quick answer: A truck suspension must meet three separate lines. Section 393.207 sets the violation line: no axle positioning part cracked, broken, loose or missing, no cracked or broken spring, plus an air suspension that holds pressure, sits level, plus admits air only after 55 psi reaches the brakes. Appendix G item 8 sets the annual inspection line: any broken or missing leaf, any broken main leaf, a deflated air suspension, plus any failed tracking part fails the yearly inspection. The CVSA out-of-service criteria set the roadside line: one-fourth or more of the leaves broken, any broken main leaf, any missing leaf, a deflated primary air bag, plus any failed U-bolt park the vehicle at once. This checker runs all three lines on the defects you enter.
What does 49 CFR 393.207 require?
Section 393.207 is the federal suspension rule for commercial motor vehicles. It sits in Part 393, the parts and accessories rules, covering every suspension type on the road: leaf springs, coil springs, torsion bars, rubber springs, composite springs, plus air suspension. The rule has seven paragraphs, lettered (a) through (g). Each one states a condition the vehicle must meet at all times, not only at inspection. A carrier that runs a vehicle outside any paragraph is in violation, even if no inspector has seen the defect yet. The section was last amended in 2005, at 70 FR 48055. The text has not changed since..
Paragraph (a) covers axles. No axle positioning part shall be cracked, broken, loose or missing. All axles must be in proper alignment.. An axle positioning part is any part that holds an axle in place: U-bolts, spring hangers, torque rods, radius rods, plus the brackets and fasteners that attach them. The rule has no tolerance for a cracked U-bolt or a loose hanger. Either one is a violation the moment it exists. Alignment is a separate duty in the same paragraph. An axle can sit out of alignment with no part failed, for example after a hard curb strike that shifts the axle on its springs. That misalignment alone violates paragraph (a)..
Paragraph (b) covers adjustable axles. Adjustable axle assemblies shall not have locking pins missing or disengaged. This is the sliding tandem rule. Every locking pin must engage its hole when the tandem is set. One pin out is a violation. The out-of-service line sits higher, at more than one-fourth of the pins, which the sliding tandem section below covers in full.
Paragraphs (c), (d), plus (e) cover springs. No leaf spring shall be cracked, broken, or missing nor shifted out of position. No coil spring shall be cracked or broken. No torsion bar or torsion bar suspension shall be cracked or broken. Three points matter here. First, the word cracked appears in all three paragraphs: a crack is a violation even before the part breaks. Second, the leaf spring paragraph adds shifted out of position, which the coil and torsion paragraphs do not. Third, the annual inspection standard is narrower than this rule, because Appendix G item 8 lists broken or missing parts only. A cracked spring violates section 393.207 but does not fail the annual inspection on the letter of the standard. The checker above applies both lines separately, so a cracked spring shows as a violation with no annual failure.
Paragraph (f) covers air suspensions with three tests: the regulator test, the level test, plus the leak test. Paragraph (g) covers air suspension exhaust controls on two-axle air suspension trailers. Both paragraphs get their own sections below, because each one carries a number drivers get wrong: 55 psi for the regulator, 3 psi in 5 minutes for the leak, plus 10 mph for the exhaust controls.
| Paragraph | What it covers | The test |
|---|---|---|
| 393.207(a) | Axles and axle positioning parts | No part cracked, broken, loose or missing. All axles in proper alignment. |
| 393.207(b) | Adjustable axles | No locking pin missing or disengaged. |
| 393.207(c) | Leaf springs | No leaf spring cracked, broken, missing or shifted out of position. |
| 393.207(d) | Coil springs | No coil spring cracked or broken. |
| 393.207(e) | Torsion bars | No torsion bar or torsion bar suspension cracked or broken. |
| 393.207(f) | Air suspensions | Regulator holds air back until 55 psi in the brakes. Vehicle level. Leakage no more than 3 psi in 5 minutes. |
| 393.207(g) | Air suspension exhaust controls | One-axle exhaust on a two-axle trailer only with controls on the trailer or a 10 mph limit. |
Two other rules sit behind section 393.207 and widen its reach. Section 396.3(a)(1) requires every part and accessory to be in safe and proper operating condition at all times. That general duty covers suspension parts the specific rule does not name, such as shock absorbers: a defective shock absorber is not a section 393.207 violation and not an out-of-service condition, but it still violates the general duty to keep the vehicle in safe operating condition. Section 396.7(a) bars operating a motor vehicle in a condition likely to cause an accident or a breakdown. A suspension defect that has not yet reached the out-of-service line can still breach section 396.7 when the condition is bad enough to risk a breakdown on the highway. The checker flags the specific rule first, then leaves the general duties to the notes.
What is the air suspension leak limit?
The air suspension leak limit is 3 psi in 5 minutes. Section 393.207(f) states it plainly: air leakage shall not be greater than 3 psi in a 5-minute time period when the vehicle air pressure gauge shows normal operating pressure. The limit is a measured loss over a fixed time, not a judgment call about whether the leak sounds bad. A leak that drops the gauge 2 psi in 5 minutes passes. A leak that drops it 4 psi in 5 minutes fails. Exactly 3 psi passes, because the rule says greater than 3 psi, not 3 psi or more.
Run the test on level ground with the vehicle parked, the wheels chocked, plus the system fully charged. Build air pressure until the governor cuts out, then watch the suspension gauge, or the primary gauge when the truck has no separate suspension gauge. Release the service brakes, because a brake application draws air and changes the reading. Note the pressure, wait 5 minutes without touching any control, then read the gauge again. The difference is the result. Enter it in the checker above: the leak field takes one decimal place, so 2.5 psi is a valid entry.
Normal operating pressure means the pressure the system normally runs at, with the governor cut out and the tanks full. The rule does not set a number for it, because normal pressure varies by vehicle. Do not run the test on a half-charged system. A low starting pressure hides a leak, because the pressure protection valve may already be closed and the suspension isolated from the supply.
The common leak points, in the order a mechanic checks them, are the air bags themselves, the air lines and fittings, the height control valve, plus the pressure protection valve. Spray soapy water on each joint while the system is charged. A leak shows as bubbles. A bag with a pinhole leak often holds pressure while parked but loses it under load, so retest after a short drive when the first test passes but the ride still feels soft.
Do not confuse the suspension leak test with the brake air loss test. The brake test runs with the service brakes applied and allows 3 psi per minute for a single vehicle, 4 psi per minute for a combination. The suspension test runs with the brakes released and allows 3 psi in 5 minutes, which is roughly fifteen times tighter. A truck can pass the brake test and fail the suspension test on the same afternoon. The Brake Pushrod Stroke Checker covers the brake side of the air system, including stroke limits plus lining thickness.
A leak over the limit is a violation, not an out-of-service condition on its own. The roadside line for air suspension is deflation: a deflated primary air suspension parks the vehicle, while a leak that holds the bag up does not. That distinction matters at the roadside. An inspector who finds a 5 psi leak writes a violation and lets the truck roll. An inspector who finds a bag flat on its stops writes the same citation code plus an out-of-service order. The checker above draws the same line: the leak field produces a violation, the deflated bag produces an out-of-service result.
What is the 55 psi regulator rule?
The 55 psi regulator rule protects the brakes from the suspension. Section 393.207(f) requires the air pressure regulator valve to hold air back from the suspension system until at least 55 psi is in the braking system. The brakes get air first. The suspension gets air only after the brake system has enough pressure to stop the truck. A regulator that lets air into the suspension at 40 psi violates the rule, because a suspension leak at that pressure could drain air the brakes need.
The valve in question is the pressure protection valve on the suspension air supply. Some trucks carry it as a separate valve in the air line to the suspension. Others build it into the height control valve assembly. Either way the function is the same: it stays closed while brake pressure builds, then opens once brake pressure reaches its set point. The set point must be 55 psi or higher. A valve set at 60 psi complies. A valve set at 50 psi does not.
Test it by draining the system, then watching both gauges as pressure builds with the engine running. The suspension should stay flat while brake pressure climbs through 30, 40, plus 50 psi. The bags should start to lift at 55 psi or above. When the bags lift at 45 psi, the valve is set too low or stuck open. The truck fails the rule.. When the bags never lift at all, the valve may be stuck closed, which is a different failure: the suspension never charges, the truck rides on its stops, plus the ride height and level tests fail next.
The number 55 psi appears twice in the suspension and brake rules, on two different devices. The regulator rule is one. The low-air warning device is the other: Appendix G item 1.f requires the warning device to operate at 55 psi and below, or at one-half the governor cut-out pressure, whichever is less. The two devices share a number but not a function. The regulator is a valve in the air supply. The warning device is a buzzer or light in the cab. A truck can pass one test and fail the other. The checker notes the pair so a driver testing the regulator does not mistake a working warning buzzer for a working valve.
A failed regulator is a violation, not an out-of-service condition. No CVSA out-of-service item covers the regulator set point. The inspector cites section 393.207(f) and the truck keeps rolling. The risk is real even so: a suspension leak downstream of a failed regulator can pull the whole air system down, including the brakes. Fix a low regulator at the next shop visit, before a small air leak turns into a brake problem.
When is a leaf spring out of service?
A leaf spring puts a truck out of service at four distinct lines. Drivers mix them up more than any other suspension rule. The first line is the count: one-fourth or more of the leaves in any spring assembly broken. The second line is the main leaf: any broken main leaf, whatever the count. The third line is the missing leaf: any leaf or portion of a leaf missing or separated. The fourth line is the displaced leaf: one or more leaves displaced in a manner that could result in contact with a tire, rim, brake drum or frame. Any one of the four parks the vehicle. The checker above tests each line separately.
The count line needs the most care, because it is a proportion, not a fixed number. One-fourth or more broken means the broken count divided by the total count, in the same spring assembly. Two broken leaves in a ten-leaf pack is 20 percent: a violation, not out of service. Three broken leaves in the same pack is 30 percent: out of service. One broken leaf in a four-leaf pack is 25 percent exactly: out of service, because the rule says one-fourth or more. One broken leaf in a nine-leaf pack is about 11 percent: a violation, not out of service. The checker does this division for the worst assembly, which is the assembly with the highest broken share. Count each assembly on its own; a broken leaf on the left spring does not add to the count on the right spring.
| Leaves broken | Total leaves | Share | Result |
|---|---|---|---|
| 1 | 10 | 10.0% | Violation, not out of service |
| 2 | 10 | 20.0% | Violation, not out of service |
| 1 | 4 | 25.0% | Out of service |
| 3 | 10 | 30.0% | Out of service |
| 2 | 9 | 22.2% | Violation, not out of service |
| 3 | 12 | 25.0% | Out of service |
The main leaf rule has no proportion at all. A main leaf is the leaf that runs the full length of the pack and forms the eyes at each end, the leaf the spring hangs from. Some packs carry more than one main leaf. Any one of them broken is out of service on its own, even when it is the only broken leaf in a twelve-leaf pack. The reason is structural: the main leaf carries the spring eyes. A broken eye leaf can let the axle shift or the spring drop. When the broken leaf is the main leaf, tick the broken main leaf box in the checker as well as entering the count. The count alone would show a violation; the main leaf box shows the out-of-service result.
The missing leaf rule is stricter than the count rule in one way that surprises drivers. A leaf that is broken but still in place counts toward the one-fourth line. A leaf that is missing or separated is out of service at once, with no count and no proportion. A leaf that has slid out of the pack far enough to separate from its neighbors is out of service even when every leaf in the pack is whole. The same logic applies to the displaced leaf rule: a leaf that has shifted sideways far enough that it could touch a tire, rim, brake drum or frame is out of service, because contact with a moving part can cut a tire or jam a brake. The Tire Compliance Checker covers the tire side of that contact, including tread depth plus sidewall damage.
A cracked leaf sits below all four lines. Section 393.207(c) covers cracked leaves, so a crack is a violation. No CVSA out-of-service item covers a crack that has not yet broken the leaf, so the truck is not parked. The crack still needs a repair date, because a cracked leaf becomes a broken leaf under load, often without warning. The checker marks a cracked leaf as a violation with an action to replace the leaf before the crack grows.
Composite leaf springs, the single-piece fiberglass or composite packs on some tractors and trailers, follow their own out-of-service lines under CVSA Part II item 11.j. A crack in a composite spring counts when the separation passes completely through the composite material. Intersecting cracks of any length are out of service. A single through crack running beyond 75 percent of the spring length is out of service. A through crack shorter than 75 percent, not intersecting another crack, is a violation below the out-of-service line. A surface crack that does not pass through the material is a violation as well. The driver should mark it and watch it at every walk-around.
When is an air suspension out of service?
An air suspension puts a truck out of service in two situations: a deflated primary air suspension, or an air spring or bag missing or detached. Everything else in the air rules is a violation below the out-of-service line. That split is the most useful fact in this section, because drivers often assume any air problem parks the truck. It does not. A leak, a tilt, a low regulator, plus a bad exhaust control are all violations. Only a suspension that has lost its air, or lost its bag, parks the vehicle.
A deflated air suspension means one or more deflated air springs or bags on the primary suspension, from a system failure, a leak, or any other cause. The truck sits on its stops on the affected side or axle. The bag holds no air at all.. CVSA Part II item 11.h makes that condition out of service. Appendix G item 8.b(7) makes it an annual inspection failure as well. The cause does not matter for the verdict: a cut bag, a failed height control valve, a broken air line, plus a failed compressor all produce the same out-of-service result when the bag ends up flat.
One exception matters for trucks with helper bags. A deflated aftermarket or secondary air bag, fitted beside a working primary leaf or coil suspension, does not result in an out-of-service condition. The primary suspension still carries the truck, so the flat helper bag is not an imminent hazard. The checker above carries that exception as its own answer: pick the secondary bag option and the result shows not out of service, with an action to fix the bag plus check the air system for leaks. The exception covers helper bags only. A deflated bag on a full air suspension, where air is the primary suspension, is out of service with no exception.
An air spring or bag missing or detached at the top or bottom is out of service under CVSA Part II item 11.i. A bag that has come off its piston or its upper mount cannot hold air and cannot carry load. The truck may still sit level if the other bags hold, which is why a visual check of every bag matters: the level test alone will not catch a detached bag on a multi-bag axle.
| Air suspension defect | Violation | Annual inspection | Out of service |
|---|---|---|---|
| Primary air bag deflated | Yes | Fail | Yes |
| Air bag missing or detached | Yes | Fail | Yes |
| Secondary helper bag deflated, primary suspension working | No | Pass | No |
| Leak over 3 psi in 5 minutes | Yes | Pass | No |
| Vehicle tilting at normal pressure | Yes | Pass | No |
| Regulator admits air below 55 psi | Yes | Pass | No |
| Cab exhaust controls with no 10 mph limit | Yes | Pass | No |
The exhaust controls deserve a closer look, because section 393.207(g) is the least known paragraph in the rule. On a two-axle air suspension trailer, the exhaust controls must not have the capability to exhaust air from one axle only, unless the controls sit on the trailer or the combination cannot travel faster than 10 mph while the air is exhausted. The reason is stability: a trailer rolling down the highway on one aired axle and one dumped axle handles badly and brakes unevenly. The rule does not prohibit exhausting both axles at once, which is how a driver lowers a trailer for loading. It does not prohibit lift axles on multi-axle units.. Cab controls that can dump one axle of a two-axle trailer, with no speed limit, violate the rule. The fix is to move the controls to the trailer or to fit a speed interlock.
What does the annual inspection check on suspension?
The annual inspection standard for suspension is Appendix G to Subchapter B, item 8, formally titled Minimum Periodic Inspection Standards. One citation note first: the standard was redesignated as Appendix G to Subchapter B in 2021, at 86 FR 57068, but eCFR still labels the page Appendix A to Part 396. Older guides call it Part 396 Appendix A. All three names point at the same text. This page uses the formal citation, Appendix G to Subchapter B, with the item numbers the inspector uses.
Item 8 fails the inspection for any of these defects. Item 8.a: any U-bolt, spring hanger, or other axle positioning part cracked, broken, loose or missing resulting in shifting of an axle from its normal position. Item 8.b(1): any leaves in a leaf spring assembly broken or missing. Item 8.b(2): any broken main leaf. Item 8.b(3): coil spring broken. Item 8.b(4): rubber spring missing. Item 8.b(5): one or more leaves displaced in a manner that could result in contact with a tire, rim, brake drum or frame. Item 8.b(6): broken torsion bar spring. Item 8.b(7): deflated air suspension. Item 8.c: any part of a torque, radius or tracking component assembly cracked, loose, broken or missing, except loose bushings in torque or track rods. Item 9.c(1), in the frame section, adds adjustable axle assemblies with locking pins missing or not engaged.
Three differences between the annual standard and the roadside criteria catch carriers out. The first is the U-bolt qualifier. Appendix G item 8.a fails the annual inspection only when a failed U-bolt, hanger, or positioning part results in shifting of the axle from its normal position. A loose U-bolt with no axle shift passes the annual inspection on the letter of the standard, yet the same loose U-bolt parks the vehicle at the roadside, because CVSA Part II item 11.a has no shift qualifier for U-bolts. The roadside line is tighter than the annual line here, which is the reverse of the usual pattern. The checker applies both lines: a loose U-bolt with no shift shows out of service with no annual failure.
The second difference is the cracked spring. Appendix G item 8 lists broken or missing parts only. A cracked leaf, coil, or torsion bar violates section 393.207, which covers cracked parts, but it does not fail the annual inspection on the letter of the standard. An inspector who finds a cracked leaf at the annual inspection passes the vehicle on the suspension item, even though the same crack is a citable violation on the highway. The checker draws the same distinction. The prose above explains why the two results differ.
The third difference is the air system. Appendix G item 8 contains no leak test, no regulator test, no level test, plus no exhaust control test. The only air item is 8.b(7), a deflated air suspension. A truck that leaks 5 psi in 5 minutes, admits air at 40 psi, plus tilts to the left can still pass the annual inspection on suspension, because none of those defects appears in item 8. All three are section 393.207 violations. The inspector can cite them at the roadside., but the annual inspection standard does not test them. The checker keeps the two results separate: the air tests drive the violation count, not the annual verdict.
Two smaller notes round out the item. After a turn, lateral axle displacement is normal with some suspensions: driving forward or backward in a straight line brings the axle back to alignment. That movement alone is not a defect under item 8.a.. Loose bushings in torque or track rods are excepted from item 8.c, so a loose bushing alone does not fail the annual inspection; a bushing missing or worn so the component can be moved by hand along its axis is a different matter. The roadside criteria treat it as out of service..
Every commercial motor vehicle, including each vehicle in a combination, needs this inspection at least once every 12 months under section 396.17. The inspection report stays on file for 14 months where the vehicle is housed or maintained, under section 396.21. A copy or a sticker showing the date must travel on the vehicle. The Annual Inspection Due-Date Tracker works out the next due date for each vehicle in the fleet, including the month-end rule for state inspections.
What is the correct ride height for a truck?
There is no federal ride height number. No paragraph in Part 393 or Part 396 sets a ride height in inches for any truck, trailer, or axle. The manufacturer sets the ride height for each suspension model. The specification lives in the suspension manual or the truck service manual, not in the regulations. A driver who asks an inspector for the legal ride height will not get a number, because no such number exists in the federal rules.
The federal test is the level test in section 393.207(f): the vehicle shall be level, not tilting to the left or right, when the gauge shows normal operating pressure. The test compares the left side with the right side, not the truck with a ruler. A truck that sits two inches low on both sides passes the federal test, because it is level. A truck that sits level on the left and an inch low on the right fails it, because it tilts. The checker asks the level question exactly that way: level, tilting left, or tilting right.
The manufacturer specification still matters, even though it is not a federal rule. Ride height is normally measured from the frame rail to the axle center, or from a fixed point on the frame to the ground, with the system at normal pressure on level ground. The height control valve holds that height by adding or venting air as the load changes. A valve out of adjustment holds the wrong height on one side or one axle, which shows up as a tilt, uneven tire wear, driveline vibration, or a trailer that tows nose-high or nose-low. When the checker shows a tilt, the height control valve on the low side is the first part to check, after the bags and lines.
Three symptoms point at a ride height problem before any gauge work. The truck leans visibly to one side at rest. The driveshaft vibrates at highway speed, because the driveline angles change with ride height. One set of tires wears faster than the other, because the low side carries more load. Any one of the three is worth a ride height measurement against the manufacturer specification, even when the truck passes the federal level test. The level test catches a tilt. It does not catch a truck sitting evenly low on both sides, which still wears tires and shakes the driveline.
Air suspension ride height also changes with load and temperature, so measure it the same way every time: level ground, normal operating pressure, the vehicle loaded as it normally runs, plus the suspension settled after a short drive. A measurement taken on a slope, or right after the truck dumped its air for loading, means nothing. Set the height control valve linkage to the manufacturer dimension when the measurement is off, then recheck the level with the checker above.
How does a suspension violation affect a CSA score?
Every section 393.207 violation lands in the Vehicle Maintenance BASIC with severity weight 7. FMCSA assigns severity weights from 1 to 10. Seven is a heavy weight: it sits above most paperwork violations and below only the most serious equipment failures. The weight applies to the violation code, not to the defect count: a truck with one broken leaf and a truck with three broken leaves each carry one violation at weight 7, because the inspector writes one citation per defect type per inspection.
An out-of-service condition adds 2 to the severity weight under the SMS methodology. A broken main leaf cited with an out-of-service order scores 9, not 7. A cracked leaf cited without an out-of-service order scores 7. That plus 2 is why the out-of-service line matters for the CSA record as well as for the roadside: the same defect costs more points when it parks the truck. The checker shows the out-of-service count separately so a carrier can see which defects carry the extra weight.
Time weights multiply the severity weight. A violation in the past 6 months counts three times its severity weight. A violation 6 to 12 months old counts twice. A violation 12 to 24 months old counts once. A violation older than 24 months drops out of the SMS window. An out-of-service suspension violation from last month therefore contributes 27 points to the Vehicle Maintenance BASIC measure: severity 7 plus 2 for the out-of-service order, times a time weight of 3. The same violation a year later contributes 9 points. The measure then feeds a percentile against peer carriers. The intervention threshold for the Vehicle Maintenance BASIC is 80 percent, or 65 percent for passenger and hazmat carriers.
The out-of-service rate also feeds the safety rating. Under Part 385 Appendix B, the vehicle factor starts from the out-of-service rate when 3 or more vehicle inspections are on file: a rate of 34 percent or higher starts the factor at Conditional. Suspension defects are a steady source of out-of-service orders, because leaf springs, U-bolts, plus air bags fail visibly and often. A carrier with a high suspension out-of-service count should expect the vehicle factor to feel it at the next compliance review. The Safety Rating Predictor runs the Appendix B table on a carrier findings to show the predicted rating.
Civil penalties sit outside the CSA score but on top of the same violations. The current inflation-adjusted penalty figures live in Part 386 Appendix B. FMCSA assesses the actual penalty after an investigation.. The FMCSA Fine Calculator works out the current maximum for a given violation. The practical lesson is the same in every system: fix suspension defects before the inspection, because the same defect costs more once an inspector writes it down.
What happens after an out-of-service order for suspension?
An out-of-service order for a suspension defect stops the vehicle where it stands. Section 396.9(c)(2) bars any person from operating a vehicle declared out of service until all repairs required by the out-of-service notice are satisfactorily completed. Operating includes towing the vehicle, with one exception: a vehicle marked out of service may be towed away by a vehicle using a crane or hoist. A standard tow behind another truck does not qualify. No person may remove the Out-of-Service Vehicle sticker before the repairs are complete, under section 396.9(c)(3).
The driver duties start at once. Section 396.9(d)(1) requires the driver who receives an inspection report to deliver a copy to the motor carrier operating the vehicle, plus to the intermodal equipment provider when the vehicle carries intermodal equipment, upon arrival at the next terminal or facility. When the driver is not scheduled to reach a terminal or facility within 24 hours, the driver must immediately mail, fax, or otherwise transmit the report to the carrier and the provider. The checker shows that deadline as a figure whenever the result is out of service.
The carrier duties follow on a 15-day clock. Section 396.9(d)(3) requires the carrier, within 15 days following the date of the inspection, to certify that all violations noted have been corrected by completing the signature portions of the form. The carrier returns the completed form to the issuing State agency only if that agency requests it. In all instances the carrier retains a copy at the principal place of business, or where the vehicle is housed, for 12 months from the date of the inspection. The conditional return is a 2026 change, effective June 22, 2026, at 91 FR 37056: before that date the carrier returned the form in every case. The 15-day certification is not conditional. It applies to every out-of-service order.
One allowance does not apply here. Section 396.7(b) lets a vehicle discovered unsafe on the highway continue in operation only to the nearest place where repairs can safely be effected, when that is less hazardous than leaving the vehicle on the highway. That allowance covers a defect the driver discovers, not a vehicle an inspector has already declared out of service. Once the out-of-service order exists, section 396.9(c)(2) bars operation until repairs are complete. The nearest-repair allowance does not override it.. A driver with a declared out-of-service suspension defect waits for the repair or the crane tow. The Out-of-Service Order Checker covers the full order lifecycle, including the deadlines plus the return-to-service steps.
Is suspension on the pre-trip inspection list?
Suspension is not one of the 11 parts on the driver vehicle inspection report list. Sections 392.7 and 396.11 list the same 11 parts and accessories the driver must inspect and report on: service brakes including trailer brake connections, parking brake, steering mechanism, lighting devices and reflectors, tires, horn, windshield wipers, rear-vision mirrors, coupling devices, wheels and rims, plus emergency equipment. Suspension does not appear. A suspension defect alone does not trigger the written DVIR report duty in section 396.11. A driver who finds only a suspension defect has no DVIR item to write it against.
That gap does not make suspension optional. Section 396.13 requires the driver, before driving, to be satisfied that the motor vehicle is in safe operating condition. The driver must also review the last driver vehicle inspection report when one is required.. Section 396.7(a) bars operating a vehicle in a condition likely to cause an accident or a breakdown. A driver who spots a broken leaf or a flat air bag and drives anyway breaches both duties, even though neither rule names suspension. The practical answer is to report every suspension defect to the carrier in writing, on the DVIR form or the carrier defect system, whether or not the 11-item list requires it. The DVIR Checker covers the report duties, signatures, plus retention for the 11 listed parts.
The walk-around check for suspension takes two minutes and catches most defects before an inspector does. Look at the U-bolts and spring hangers for cracks, looseness, or missing nuts. Look at the leaf packs for broken, missing, or shifted leaves. Check the main leaf eyes.. Look at the air bags for cuts, bulges, or rubbing. Listen for leaks at the bags, lines, plus fittings. Look at the height control valve linkage for damage or disconnection. Stand back and check the level: the truck should sit even, left to right, at normal pressure. Then check the sliding tandem pins: every pin engaged, the locking mechanism sound. The Pre-Trip Inspection Checklist puts these checks in walk-around order with the rest of the vehicle. The Steering Lash Checker covers the steering side of the same walk-around, since loose steering and shifted axles often appear together.
Run the air tests on a schedule, not only when something looks wrong. The 5-minute leak test and the regulator check take ten minutes with the truck parked and chocked. A monthly test catches a slow leak before it becomes a flat bag at the roadside. A fleet that tests monthly will rarely see a suspension out-of-service order, because the defects that park trucks, deflated bags and broken leaves, give weeks of warning first.
How do you use the Suspension and Air System Checker?
Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the verdict change.
- Pick the suspension type for the axle you are checking.
- Tick every axle, spring, tracking, bushing and shock defect you found on the walk-around.
- Enter the leaf count, the broken leaf count, plus the locking pin counts.
- Enter the regulator cut-in pressure plus the 5-minute leak test result, then pick the level and the air bag condition.
- Read the verdict, the check table, plus the figures.
- Copy the summary and the fix list for the maintenance file.
Use measurements from the truck, not guesses. The leaf count, the pin count, the regulator pressure, plus the leak result are all numbers you can read off the vehicle in a few minutes. A guess in any of those fields produces a guess in the verdict. When a number is uncertain, run the tool twice: once with the low value, once with the high value. The range of verdicts tells you how much the uncertain number matters.
Read the check table before the action list. It shows each defect on its own line with its own tier: out of service, violation, or pass, plus whether it fails the annual inspection. The tiers decide the order of work. Fix the out-of-service conditions first, because they park the vehicle. Fix the violations next, because they carry severity weight 7 each. Fix the annual failures before the next periodic inspection, because the truck cannot pass with them open.
Questions drivers ask
How many broken leaves put a truck out of service?
One-fourth or more of the leaves in any spring assembly. Two broken leaves in a ten-leaf pack is 20 percent, a violation but not out of service. Three broken leaves in the same pack is 30 percent, out of service. One broken leaf in a four-leaf pack is 25 percent exactly, out of service. Any broken main leaf, any missing or separated leaf, plus any leaf displaced toward a tire, rim, brake drum or frame are out of service on their own, whatever the count.
What is the air suspension leak limit?
Three psi in 5 minutes at normal operating pressure, under section 393.207(f). Run the test with the system fully charged and the brakes released, watch the gauge for 5 minutes, then read the loss. Exactly 3 psi passes, because the rule says greater than 3 psi. A leak over the limit is a violation, not an out-of-service condition. A deflated air suspension is out of service.
Can I drive with a cracked leaf spring?
A cracked leaf is a violation under section 393.207(c), but it is not an out-of-service condition and it does not fail the annual inspection, because Appendix G item 8.b(1) lists broken or missing leaves only. The truck can legally roll, but the crack will grow into a break under load, often without warning. Replace the leaf before the next long run. Report the defect to the carrier..
What is the 55 psi rule for air suspension?
The air pressure regulator valve must not allow air into the suspension system until at least 55 psi is in the braking system, under section 393.207(f). The brakes get air first, so a suspension leak cannot drain the brake system. A regulator that admits air below 55 psi is a violation. The same number appears on the low-air warning device, which is a separate cab alarm, not the regulator valve.
Is a deflated air bag out of service?
A deflated primary air suspension bag is out of service under CVSA Part II item 11.h. It fails the annual inspection under Appendix G item 8.b(7).. A deflated aftermarket or secondary air bag beside a working primary leaf or coil suspension is not out of service, because the primary suspension still carries the truck. An air bag missing or detached at the top or bottom is out of service under item 11.i.
Does a suspension defect fail the annual inspection?
It depends on the defect. Appendix G item 8 fails the inspection for a failed positioning part that shifts the axle, any broken or missing leaf, any broken main leaf, a broken coil spring, a missing rubber spring, a displaced leaf, a broken torsion bar, a deflated air suspension, plus any failed tracking part. Item 9.c(1) adds locking pins missing or not engaged. A cracked spring, an air leak, a low regulator, plus a tilt do not fail the annual inspection, because item 8 does not list them.
Related tools
- Pre-Trip Inspection Checklist: the full walk-around in order, with suspension checks beside the rest of the vehicle.
- DVIR Checker: what the driver must report, who signs, plus how long the report is kept.
- Annual Inspection Due-Date Tracker: the next due date for each vehicle, plus what must travel on the truck.
- Out-of-Service Order Checker: the full order lifecycle, deadlines, plus the return-to-service steps.
Sources
- 49 CFR 393.207, Suspension systems (eCFR, read verbatim Nov 19, 2026; last amended 70 FR 48055, Aug. 15, 2005)
- Appendix G to Subchapter B, Minimum Periodic Inspection Standards, item 8 (eCFR, read verbatim Nov 19, 2026; eCFR labels the page Appendix A to Part 396; redesignated at 86 FR 57068, Oct. 14, 2021)
- 49 CFR 396.9, Inspection of motor vehicles and intermodal equipment in operation (eCFR, read verbatim Nov 19, 2026; last amended 91 FR 37056, June 22, 2026)
- 49 CFR 396.7, Unsafe operations forbidden (eCFR, read verbatim Nov 19, 2026)
- CVSA 2026 Out-of-Service Criteria Now in Effect (CVSA, Apr. 1, 2026; the 17 changes contain no suspension item)