Do not drive on a brake past its limit. A stroke past the readjustment limit is an inspection failure. A lining below the minimum leaves no braking margin.
Answer for one brake and one vehicle. Every answer updates as you change each field.
Pushrod stroke
Measure with the engine off, reservoir pressure at 80 to 90 psi and the brakes fully applied. The size is stamped on the chamber or on the data plate.
Lining thickness
Measure drum lining at the shoe center. A lining worn to its wear indicator fails at any measured thickness.
ABS and adjusters
The manufacture date is on the certification label. The month matters only for a vehicle built in a threshold year.
Brake performance reference
All checks pass
The pushrod stroke is within its readjustment limit. The lining is at or above its minimum. The ABS lamp cycle is normal. No repair is needed on these checks.
The checks
| Check | Result | Detail |
|---|---|---|
| Pushrod stroke | Pass | Limit for a clamp-type Type 30 chamber standard-stroke: 2 in (50.8 mm). Measured stroke 1.75 in. Margin 0.25 in. |
| Lining thickness | Pass | Minimum for a non-steering axle air drum brake: 1/4 in. Measured lining 0.31 in. Margin 0.06 in. |
| ABS required | Required | ABS is required: an air braked truck tractor manufactured on or after March 1, 1997 must have ABS (49 CFR 393.55(c)(1)). |
| ABS malfunction lamp | Normal | The ABS lamp lights at power-up and goes out. That is the correct cycle. |
| Trailer exterior ABS lamp | Not applicable | The exterior trailer ABS lamp applies to trailers and dollies only. |
| Automatic brake adjusters | Required | Automatic brake adjusters are required: this vehicle was manufactured on or after October 20, 1994 and has air brakes (49 CFR 393.53(b)). An air braked vehicle from that date also needs a brake adjustment indicator when the adjuster is external and the pushrod is exposed (49 CFR 393.53(c)). |
| Brake performance, 49 CFR 393.52 | Reference | All other property-carrying vehicles and combinations. Braking force at least 43.5 percent of gross weight. Deceleration at least 14 ft/s/s. Service stop from 20 mph within 40 ft. Emergency stop from 20 mph within 90 ft. |
Notes
- Section 393.47 requires the same size brake chambers and the same effective slack adjuster length on each end of an axle.
- Measure pushrod stroke with the engine off, reservoir pressure at 80 to 90 psi and the brakes fully applied (Part 396 Appendix A item 1.a.(5)).
- This tractor also needs a trailer ABS malfunction lamp in the cab (49 CFR 393.55(d)(2)).
Actions
- No action needed on these checks. Keep the measurements with the inspection record.
This checker applies the federal brake rules in 49 CFR Parts 393 and 396 to your answers. It is not legal advice. Confirm the chamber size and the manufacture date from the vehicle before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice โ check the current regulation and your company policy before you rely on a result.
Quick answer: The pushrod stroke limit is the maximum travel of a brake chamber pushrod with the brakes fully applied, set by chamber type and size in the federal brake rule. A clamp Type 30 chamber has a limit of 2 in. A clamp Type 36 chamber has a limit of 2ยฝ in. This checker looks up the limit for your chamber. It checks your lining against the minimum for your axle and brake type. It also checks whether your vehicle needs ABS and whether its lamps work.
What is the brake pushrod stroke limit?
The pushrod stroke limit is the maximum distance a brake chamber pushrod may travel when the brakes are fully applied. It is the readjustment limit in 49 CFR 393.47(e). When the stroke passes the limit, the brake is out of adjustment and the vehicle fails its annual inspection.
The limit depends on the chamber. A small clamp Type 6 chamber has a limit of 1ยผ in. A clamp Type 30 chamber has a limit of 2 in. A clamp Type 36 chamber has a limit of 2ยฝ in. The checker above looks up the brake pushrod stroke limits for your chamber type and size and compares the limit with your measured stroke.
Stroke grows as the lining wears. The slack adjuster takes up the wear and keeps the stroke short. When the adjuster can no longer take up the wear, the stroke grows past the limit. That is the signal to adjust or repair the brake.
The limit is a federal operating standard, not a suggestion. Section 393.47(e) says the pushrod stroke must not be greater than the values in its tables. Part 396 Appendix A says any brake stroke past the readjustment limit will be rejected at the annual inspection.
How do you measure pushrod stroke?
Measure with the engine off, reservoir pressure at 80 to 90 psi and the brakes fully applied. That is the measurement condition in Part 396 Appendix A item 1.a.(5). A measurement taken at full system pressure or with the engine running does not match the inspection standard.
Mark the pushrod at the face of the chamber with the brakes released. Apply the brakes fully and mark the pushrod again at the same face. The distance between the two marks is the stroke. Measure in inches to the nearest 16th.
Measure every brake, not a sample. Stroke varies by wheel because lining wear and adjuster condition vary by wheel. A single brake past the limit is enough to fail the inspection for that brake.
Check the automatic adjuster while you measure. A brake that is out of adjustment on a vehicle with automatic adjusters has an underlying problem. The inspection standard requires the problem to be corrected. It is not acceptable to turn the adjuster by hand and move on.
What are the pushrod stroke limits by chamber type?
Section 393.47(e) lists four chamber families with their own tables: clamp-type, Bendix DD-3, bolt-type and Rotochamber. Each table gives the readjustment limit by chamber size. The checker above carries all four tables.
Clamp-type chambers are the most common. Sizes run from Type 6 to Type 36. Standard stroke limits run from 1ยผ in to 2ยฝ in. Long-stroke versions of Types 12 through 30 have larger limits. Types 20 and 24 with a 3-inch rated stroke have a limit of 2ยฝ in.
The DD-3 table lists Type 30 only, with a limit of 2ยผ in. Bolt-type chambers use letters A through G, with limits from 1ยผ in to 2ยผ in. Rotochamber sizes run from Type 9 to Type 50, with limits from 1ยฝ in to 3 in.
An actuator type that is not listed in any table has a limit of 80 percent of the rated stroke marked on the actuator by the actuator manufacturer. The checker applies that rule when you select the unlisted option and enter the rated stroke.
| Clamp-type chamber | Outside diameter | Standard stroke limit | Long stroke limit |
|---|---|---|---|
| Type 6 | 4ยฝ in (114 mm) | 1ยผ in (31.8 mm) | Not listed |
| Type 9 | 5ยผ in (133 mm) | 1โ in (34.9 mm) | Not listed |
| Type 12 | 5 11/16 in (145 mm) | 1โ in (34.9 mm) | 1ยพ in (44.5 mm) |
| Type 16 | 6โ in (162 mm) | 1ยพ in (44.5 mm) | 2 in (50.8 mm) |
| Type 20 | 6 25/32 in (172 mm) | 1ยพ in (44.5 mm) | 2 in (50.8 mm); 2ยฝ in with a 3-inch rated stroke |
| Type 24 | 7 7/32 in (184 mm) | 1ยพ in (44.5 mm) | 2 in (50.8 mm); 2ยฝ in with a 3-inch rated stroke |
| Type 30 | 8 3/32 in (206 mm) | 2 in (50.8 mm) | 2ยฝ in (63.5 mm) |
| Type 36 | 9 in (229 mm) | 2ยฝ in (63.5 mm) | Not listed |
| DD-3, bolt-type and Rotochamber | Outside diameter | Readjustment limit |
|---|---|---|
| Bendix DD-3 Type 30 | 8โ in (206 mm) | 2ยผ in (57.2 mm) |
| Bolt Type A | 6 15/16 in (176 mm) | 1โ in (34.9 mm) |
| Bolt Type B | 9 3/16 in (234 mm) | 1ยพ in (44.5 mm) |
| Bolt Type C | 8 1/16 in (205 mm) | 1ยพ in (44.5 mm) |
| Bolt Type D | 5ยผ in (133 mm) | 1ยผ in (31.8 mm) |
| Bolt Type E | 6 3/16 in (157 mm) | 1โ in (34.9 mm) |
| Bolt Type F | 11 in (279 mm) | 2ยผ in (57.2 mm) |
| Bolt Type G | 9โ in (251 mm) | 2 in (50.8 mm) |
| Rotochamber Type 9 | 4 9/32 in (109 mm) | 1ยฝ in (38.1 mm) |
| Rotochamber Type 12 | 4 13/16 in (122 mm) | 1ยฝ in (38.1 mm) |
| Rotochamber Type 16 | 5 13/32 in (138 mm) | 2 in (50.8 mm) |
| Rotochamber Type 20 | 5 15/16 in (151 mm) | 2 in (50.8 mm) |
| Rotochamber Type 24 | 6 13/32 in (163 mm) | 2 in (50.8 mm) |
| Rotochamber Type 30 | 7 1/16 in (180 mm) | 2ยผ in (57.2 mm) |
| Rotochamber Type 36 | 7โ in (194 mm) | 2ยพ in (69.9 mm) |
| Rotochamber Type 50 | 8โ in (226 mm) | 3 in (76.2 mm) |
What is the Type 36 pushrod stroke limit?
The Type 36 clamp chamber limit is 2ยฝ in. That is the current value in 49 CFR 393.47(e) and in Part 396 Appendix A. Many printed charts and web pages still show 2ยผ in. Those charts are stale.
The limit changed on 14 October 2021, when FMCSA published 86 FR 57076. The amendment corrected the Type 36 row in both tables from 2ยผ in to 2ยฝ in. The correction matched the limit to the chamber rated stroke and to the long-stroke Type 30 value.
A stale chart can cost a driver a citation or a failed inspection. A Type 36 stroke of 2โ in passes the current limit and fails the stale one. Check the date on any chart you use. This checker uses the current eCFR text, verified in November 2026.
What is the minimum brake lining thickness?
The minimum lining thickness depends on the axle and the brake type. Section 393.47(d) sets the operating minima. The steering axle has its own numbers because a steering brake failure is harder to control than a drive or trailer brake failure.
On the steering axle, an air drum brake needs 3/16 in at the shoe center for a shoe with a continuous strip of lining, or 1/4 in for a shoe with two pads. An air disc brake needs 1/8 in. A hydraulic or electric brake needs 1/16 in.
On a non-steering axle, an air drum brake needs 1/4 in at the shoe center. An air disc brake needs 1/8 in. A hydraulic or electric brake needs 1/16 in. A lining worn to its wear indicator fails at any thickness.
Watch the steering drum conflict. Section 393.47 allows 3/16 in for a continuous strip shoe on the steering axle. The annual inspection standard in Part 396 Appendix A rejects any steering drum lining under 1/4 in. A lining at 3/16 in is legal to operate and still fails the annual inspection. The checker flags that gap.
When is ABS required on a truck?
ABS has been required on new commercial vehicles in stages since 1997. The dates are in 49 CFR 393.55. The rule turns on the vehicle type, the brake system and the manufacture date. The checker applies all three.
Air braked truck tractors manufactured on or after March 1, 1997 must have ABS. Other air braked commercial vehicles, including single-unit trucks, buses, trailers and dollies, must have ABS when manufactured on or after March 1, 1998. Hydraulic braked trucks and buses must have ABS when manufactured on or after March 1, 1999.
Driveaway-towaway operations are excepted. A truck tractor or truck delivered in a driveaway-towaway operation does not need ABS under section 393.55. The exception covers the delivery operation, not the vehicle for its working life.
A vehicle built before its date has no federal ABS duty. The annual inspection lamp checks apply to the same date bands. A dead ABS lamp on an older vehicle with factory ABS is still worth fixing, because a working ABS keeps the vehicle stable in a hard stop.
What must the ABS warning lamps do?
The ABS malfunction lamp must light when power is first applied to the ABS controller and go out while power stays applied. That is the cycle in Part 396 Appendix A item 1.l. A lamp that never lights, a lamp that stays on and a missing lamp are all inspection failures.
Tractors built after March 1, 2001 have two lamps: one for the power unit and one for the units they tow. Both must work. A tractor from March 1, 2001 onward must have a trailer ABS malfunction lamp in the cab. A single-unit vehicle equipped to tow another air-braked vehicle needs the same cab lamp.
Trailers need an exterior ABS lamp. Each trailer and dolly manufactured on or after March 1, 1998 must have an exterior ABS malfunction indicator lamp. The lamp must cycle when power is applied to the constant ABS power circuit or to the stop lamp circuit.
Trailers built on or after March 1, 2001 also need an ABS malfunction circuit with a connection to the towing vehicle. The circuit carries the trailer fault signal to the cab lamp. The checker lists each lamp and circuit duty for your vehicle and date.
What are automatic brake adjusters and when are they required?
An automatic brake adjuster, often called an automatic slack adjuster, keeps the pushrod stroke short as the lining wears. It turns the slack adjuster a small amount each time the brake applies. A manual adjuster needs a wrench and a regular schedule.
Section 393.53 requires automatic adjusters on hydraulic braked vehicles manufactured on or after October 20, 1993 and on air braked vehicles manufactured on or after October 20, 1994. Air braked vehicles from the 1994 date also need a brake adjustment indicator when the adjuster is external and the pushrod is exposed.
An automatic adjuster that is replaced with a manual adjuster is an inspection failure. So is an automatic adjuster with damaged, loose or missing parts. The inspection standard also rejects a brake that the adjuster cannot keep within its stroke limit.
Never fix an out-of-adjustment automatic brake with a wrench alone. Part 396 Appendix A item 1.m.(4) requires the underlying problem to be found and corrected first. The cause may be a worn bushing, a cracked drum, loose mounting hardware or a failed adjuster. A manual adjustment that hides the cause leaves the brake unsafe.
What stopping distance does section 393.52 require?
Section 393.52 sets braking force, deceleration and stopping distance from 20 mph by vehicle class. A truck or combination must meet all three on its service brakes. The emergency brake system has its own stopping distance from 20 mph.
Most property-carrying trucks and combinations fall in the last row of the table: braking force at least 43.5 percent of gross weight, deceleration at least 14 feet per second per second, a service stop within 40 feet and an emergency stop within 90 feet. Single-unit property vehicles over 10,000 pounds except tractors stop within 35 feet on service brakes and 85 feet on the emergency system.
The test runs on a hard surface that is substantially level, dry, smooth and free of loose material. The vehicle must stay in the center of a 12-foot-wide lane for the whole stop. The distance is measured from the point where the driver starts to move the brake control.
The checker shows the row for your vehicle class. The numbers are a reference for the inspection and for a road test. A vehicle that cannot stop inside its distance has a brake problem even when every pushrod stroke measures inside its limit.
| Vehicle class | Braking force, percent of gross weight | Deceleration, ft/s/s | Service stop from 20 mph | Emergency stop from 20 mph |
|---|---|---|---|---|
| Passenger, 10 or fewer seats, car chassis | 65.2 | 21 | 20 ft | 54 ft |
| Passenger, over 10 seats, car chassis, or truck or bus chassis at 10,000 lb GVWR or less | 52.8 | 17 | 25 ft | 66 ft |
| All other passenger-carrying vehicles | 43.5 | 14 | 35 ft | 85 ft |
| Single unit property, 10,000 lb GVWR or less | 52.8 | 17 | 25 ft | 66 ft |
| Single unit property over 10,000 lb GVWR except a tractor, or a 2-axle towing vehicle with a trailer of 3,000 lb GVWR or less, or a driveaway or towaway combination | 43.5 | 14 | 35 ft | 85 ft |
| All other property-carrying vehicles and combinations | 43.5 | 14 | 40 ft | 90 ft |
What happens when a brake is past its stroke limit?
The brake fails the annual inspection. Part 396 Appendix A item 1.a.(5) says any brake stroke past the readjustment limit will be rejected. The inspector records the defect and the vehicle does not pass until the brake is repaired.
At a roadside inspection, the same brake can put the vehicle out of service. Under the CVSA out-of-service criteria, a brake 1/4 in or more past its readjustment limit counts as one defective brake toward the 20 percent rule. When 20 percent or more of the brakes on the vehicle are defective, the vehicle is placed out of service.
The Brake Inspection Readiness Checker runs the 20 percent count for a full vehicle. This checker covers the chamber lookup and the lining measurement that the readiness checker does not include. Use both together before an inspection.
A past-limit brake also signals wear elsewhere. Check the lining thickness, the drum condition and the adjuster before you readjust. A brake that keeps drifting out of adjustment has a part failing somewhere in the foundation brake.
A brake violation also costs CSA points and penalty exposure. The CSA Violation Points Checker shows the severity weight for a brake violation and the day it falls off the 24-month window. The FMCSA Fine Calculator shows the maximum civil penalty for operating with defective brakes.
What else does the annual brake inspection check?
Stroke and lining are two items in a longer list. Part 396 Appendix A item 1 covers the full brake system: service brakes, the parking brake, drums and rotors, hoses and tubing, the low-pressure warning device, the tractor protection valve, the air compressor, electric brakes, hydraulic brakes, vacuum systems, ABS and automatic adjusters.
Hoses fail on damage through the outer reinforcement ply, on bulges and swelling under pressure and on audible leaks. Drums and rotors fail on external cracks that open on application and on any missing portion. The low-pressure warning device must operate at 55 psi and below, or at half the governor cut-out pressure, whichever is less.
The inspector keeps a report for every annual inspection. Section 396.21 requires the report to be retained for 14 months from the inspection date, where the vehicle is housed or maintained. The DOT Record Retention Checker works out the keep-until date for inspection reports and every other record type.
A pre-trip inspection catches many of the same defects before the annual inspection does. The Pre-Trip Inspection Checklist covers the daily walk-around, including the air loss test and the low-air warning test. A daily check finds a drifting stroke weeks before the annual inspection.
Tires, steering and lighting have their own limits. The Tire Compliance Checker covers tread depth and tire condition. The Steering Lash Checker covers steering wheel play.
Why do the stroke limits differ by chamber size?
A larger chamber has a longer rated stroke. The pushrod must travel farther to apply the same brake force through a longer lever. The readjustment limit scales with the chamber so that each size keeps a safe margin before the slack adjuster runs out of travel.
The tables reflect that scale. A clamp Type 6 chamber has a limit of 1ยผ in. A clamp Type 36 chamber has a limit of 2ยฝ in. The limit roughly doubles across the size range, matching the growth in chamber diameter and rated stroke.
Long-stroke chambers have larger limits than standard chambers of the same size. A clamp Type 30 long-stroke chamber has a limit of 2ยฝ in against 2 in for the standard chamber. The extra travel comes from the longer rated stroke of the long-stroke design.
The 80 percent rule for unlisted actuators follows the same logic. A limit at 80 percent of the rated stroke leaves a 20 percent margin before the pushrod reaches the end of its travel. Never guess a limit for an unlisted actuator. Read the rated stroke from the marking on the actuator.
How do you use the Brake Pushrod Stroke, Lining and ABS Checker?
- Select the chamber family and size, then the stroke type for a clamp chamber. Enter the measured pushrod stroke in inches.
- Enter the lining thickness in inches, the axle position and the brake type. Say whether the lining is worn to the wear indicator.
- Select the vehicle type and enter the manufacture year and month. Answer the ABS lamp questions for the power unit and the trailer.
- Select the vehicle class for the section 393.52 brake performance reference.
- Read the verdict and the check table, with the limit, the margin and the lamp results.
- Copy the summary for the inspection file, or reset the checker to start over.
Frequently asked questions
What is the pushrod stroke limit for a Type 30 brake chamber?
A clamp Type 30 chamber has a readjustment limit of 2 in for a standard stroke chamber and 2ยฝ in for a long-stroke chamber. A Bendix DD-3 Type 30 chamber has a limit of 2ยผ in. A Rotochamber Type 30 has a limit of 2ยผ in. The limit depends on the chamber family as well as the size.
What is the minimum brake lining thickness for a truck?
On a non-steering axle, an air drum brake needs 1/4 in, an air disc brake needs 1/8 in and a hydraulic or electric brake needs 1/16 in. On the steering axle, an air drum brake needs 3/16 in for a continuous strip shoe or 1/4 in for a two-pad shoe. A lining worn to its wear indicator fails at any thickness.
When did ABS become required on semi trucks?
ABS has been required on air braked truck tractors manufactured on or after March 1, 1997. Other air braked commercial vehicles need ABS from March 1, 1998. Hydraulic braked trucks and buses need ABS from March 1, 1999. Driveaway-towaway operations are excepted.
What does it mean when the ABS light stays on?
An ABS lamp that stays illuminated while power is continuously applied signals an ABS malfunction. The annual inspection standard rejects it. The ABS may still have base braking, but the antilock function is not working. Repair the fault before driving.
Can you manually adjust automatic slack adjusters?
No, not as a fix on its own. Part 396 Appendix A requires the underlying problem to be found and corrected when a brake with an automatic adjuster is out of adjustment. A manual adjustment without a repair hides the cause and leaves the brake unsafe.
How often should pushrod stroke be checked?
Check stroke at every pre-trip inspection and at every preventive maintenance visit. Stroke grows as the lining wears, so a brake inside its limit today can pass the limit before the next annual inspection. A daily check finds a drifting brake early.
Related tools
- Brake Inspection Readiness Checker: run the seven CVSA brake checks and the 20 percent defective-brake count for a full vehicle.
- Pre-Trip Inspection Checklist: tick off the daily pre-trip checks, including the air loss test and the low-air warning test.
- Tire Compliance Checker: check tread depth and tire condition against the DOT minima by axle.
- Steering Lash Checker: check steering wheel play against the section 393.209 limits by wheel size.
- CSA Violation Points Checker: pick a violation and its date to see the severity weight, the BASIC, the time weight and the day it falls off the 24-month SMS window.
- FMCSA Fine Calculator: check the maximum FMCSA fine for any violation under 49 CFR Part 386, with the exact citation and next steps.
- Trucking Tools: browse every free calculator on Trucking Mind.
Sources
- 49 CFR 393.47, Brake actuators, slack adjusters, linings/pads and drums/rotors. ecfr.gov/current/title-49/section-393.47 Accessed November 19, 2026.
- 49 CFR 393.52, Brake performance. ecfr.gov/current/title-49/section-393.52 Accessed November 19, 2026.
- 49 CFR 393.53, Automatic brake adjusters and brake adjustment indicators. ecfr.gov/current/title-49/section-393.53 Accessed November 19, 2026.
- 49 CFR 393.55, Antilock brake systems. ecfr.gov/current/title-49/section-393.55 Accessed November 19, 2026.
- 49 CFR Part 396, Appendix A, Minimum Periodic Inspection Standards, item 1. ecfr.gov, Appendix A to Part 396 Accessed November 19, 2026.
- 86 FR 57076, 14 October 2021, amendment to 49 CFR 393.47(e) and Part 396 Appendix A: Type 36 clamp chamber limit corrected to 2ยฝ in. federalregister.gov/documents/2021/10/14/2021-22269 Accessed November 19, 2026.