One tire at a time. This checker runs one tire against 49 CFR 393.75 and the annual inspection standard in Part 396 Appendix A item 10. A tire that is likely out of service must not be driven. Park it and fix it first.
Answer for one tire. Every answer updates as you change each field.
The tire
Measure in a major tread groove, away from tie bars, humps and fillets. A major groove is one with a tread wear indicator. The adjacent-groove question decides the steering out-of-service line. The three-spot question decides the out-of-service line for other tires.
Condition: check every defect you can see
Tire type and service
The regroove and retread bans depend on the vehicle type and the tire position. A bus front wheel allows no regrooved, recapped or retreaded tire at all. A truck or truck-tractor front wheel allows no regrooved tire rated 4,920 lb or more.
Speed-restricted tire
A speed-restricted tire carries a label that limits it to 55 mph or less. The operating rule bars driving above the rated limit. The annual inspection standard fails the tire unless the carrier specifically designated it for the vehicle.
Load
The load must not exceed the rating marked on the sidewall or the rating in the FMVSS 119 publication. Leave both fields blank to skip the load check. The rating also decides the heat-buildup correction below.
Inflation pressure
Table 1 in section 393.75 has one row only: 41-55 mph average speed in the previous hour. The checker subtracts 15 psi for a tire rated over 4,000 lb and 5 psi for a tire rated 4,000 lb or less. Outside 41-55 mph the regulation gives no correction, so measure the tire cold.
This tire passes the federal tire rules
Tread depth, condition, load and inflation all meet 49 CFR 393.75 and the annual inspection standard in Part 396 Appendix A item 10.
| Check | Result | Detail |
|---|---|---|
| Tread depth, federal minimum | Pass | 6/32 in at the lowest point. Steering tires need at least 4/32 in in a major tread groove (49 CFR 393.75(b)). |
| Tread depth, out-of-service line | Pass | Above the out-of-service line of less than 2/32 in in two adjacent major grooves (CVSA item 12.a.(1)). |
| Exposed ply or belt | Pass | No ply or belt material showing through the tread or sidewall (49 CFR 393.75(a)(1)). |
| Tread or sidewall separation | Pass | No tread or sidewall separation (49 CFR 393.75(a)(2)). |
| Flat tire or audible leak | Pass | No flat tire and no audible leak (49 CFR 393.75(a)(3)). |
| Cut exposing ply or belt | Pass | No cut exposing ply or belt material (49 CFR 393.75(a)(4)). |
| Regrooved, recapped or retreaded tire | Pass | A new tire has no regroove, recap or retread restriction at any position. |
| Speed-restricted tire | Pass | Not a speed-restricted tire. No speed limit applies to this tire under section 393.75(f). |
| Load against sidewall rating | Pass | 5,500 lb on a tire rated 6,175 lb, 89 percent of the rating (49 CFR 393.75(g)). |
| Cold inflation pressure | Pass | Measured 110 psi after driving at 50 mph average. Table 1 buildup 15 psi. Estimated cold pressure 95 psi. That meets the 95 psi required for this load. That stays above half the 105 psi sidewall maximum (52.5 psi). |
| Not for Highway Use marking | Pass | No Not for Highway Use marking (Part 396 Appendix A item 10(a)(5), (b)(7)). |
| Tire contact and lodged items | Pass | No tire contact with the vehicle or its mate. Nothing is lodged between dual tires. |
| Annual inspection extras | Pass | No boot, patch, mixing, tube-stem or flap problem on this tire. |
The figures
| Figure | Value | Note |
|---|---|---|
| Tread depth | 6/32 in | Minimum 4/32 in on a steering axle |
| Load on this tire | 5,500 lb | 89 percent of the 6,175 lb rating |
| Measured pressure | 110 psi | After driving, 50 mph average |
| Heat buildup, Table 1 | 15 psi | 41-55 mph row, rating over 4,000 lb |
| Estimated cold pressure | 95 psi | Required 95 psi for this load |
| Half the sidewall maximum | 52.5 psi | Sidewall maximum 105 psi |
What to do
- Keep the gauge readings with the vehicle records. Re-check tread depth at the next pre-trip inspection.
Notes
- Measure tread depth in a major tread groove, away from tie bars, humps and fillets. A major groove is one with a tread wear indicator.
- Table 1 in section 393.75 has one row only: 41-55 mph average speed in the previous hour. No correction is published for other speeds.
This checker applies 49 CFR 393.75 and Part 396 Appendix A item 10 to your answers. It is not legal advice. Confirm the tread depth and pressure readings with a gauge before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice โ check the current regulation and your company policy before you rely on a result.
Quick answer: A truck steer tire needs at least 4/32 in of tread depth. Every other tire needs at least 2/32 in. The out-of-service line sits lower: below 2/32 in in two adjacent major grooves for a steer tire, below 1/32 in at three separate spots for other tires. Exposed ply or belt cord, separation, a flat tire or leak and a cut that exposes ply or belt cord all fail the federal tire rules at once. This checker runs one tire against 49 CFR 393.75 and the annual inspection standard in Part 396 Appendix A item 10.
What is the minimum truck tire tread depth?
The federal minimum tread depth for a truck steer tire is 4/32 in. Section 393.75(b) sets that line for the front wheels of a bus, truck or truck-tractor. The measurement is taken at any point on a major tread groove. A tire that falls below 4/32 in anywhere on a major groove fails the rule, even when the rest of the tire looks fine.
Every other tire on the vehicle needs at least 2/32 in. Section 393.75(c) covers drive tires, trailer tires and any other position. The same measurement rule applies: any point on a major tread groove counts. One worn spot is enough to fail the tire.
| Tire position | Federal minimum | Out-of-service line |
|---|---|---|
| Steering axle | 4/32 in | Below 2/32 in in two adjacent major grooves |
| Drive, trailer and other tires | 2/32 in | Below 1/32 in in two adjacent grooves at three separate spots at least 8 in apart |
Never measure at a tie bar, hump or fillet. The regulation says the depth is never measured at those spots. Tie bars sit in the groove and give a false reading. Measure in the open part of a major groove, away from any raised bar or hump.
A new steer tire starts life with about 18/32 in to 22/32 in of tread. A new drive tire starts with about 26/32 in to 32/32 in. The legal minimum is far below the starting depth. A tire at 5/32 in on a steer axle passes the rule, but it has little life left and it is close to the line.
What is the difference between the legal minimum and the out-of-service line?
The legal minimum and the out-of-service line are two different lines. The legal minimum is the tread depth below which the tire breaks the federal rule. The out-of-service line is the tread depth below which an inspector parks the vehicle on the spot. A tire can break the rule without being parked. That gap catches drivers out.
For a steer tire, the legal minimum is 4/32 in. The out-of-service line is below 2/32 in in two adjacent major grooves at the same spot. A steer tire at 3/32 in fails the federal rule and earns a violation, but it is not out of service. A steer tire at 1/32 in in two adjacent grooves is out of service.
For other tires, the legal minimum is 2/32 in. The out-of-service line is below 1/32 in in two adjacent grooves at three separate locations at least 8 in apart. All three spots must be below the line. One spot below 1/32 in is a violation, not an out-of-service condition.
Some third-party sites state the steer out-of-service line as 4/32 in. That is wrong. Four thirty-seconds is the FMCSR legal minimum, not the out-of-service line. The CVSA criteria set the out-of-service line at below 2/32 in in two adjacent grooves. This checker uses the CVSA line.
The gap matters for roadside decisions. A violation costs CSA points and a fine. An out-of-service order costs the load, the schedule and the tow. Knowing which line you crossed tells you whether you drive away with a citation or wait for a tire service truck.
How do you measure truck tire tread depth?
Use a tread depth gauge. Push the probe into a major tread groove until the base sits flat on the tread surface. Read the depth in 32nds of an inch. A gauge costs little and fits in a pocket. It beats a coin test, which cannot tell 3/32 in from 5/32 in.
Measure at the lowest point. Check the groove at several spots around the tire and across the tread face. Uneven wear can leave one spot far below the rest. The regulation sets the minimum at any point on a major tread groove, so the worst spot decides.
Find a major groove. A major groove is one with a tread wear indicator in it. Tread wear indicators are the raised bars that sit across the groove at 2/32 in. When the tread wears flush with an indicator, the tire is at 2/32 in. That is the legal minimum for a non-steer tire and below the minimum for a steer tire.
Stay away from tie bars, humps and fillets. Those raised parts sit inside the groove and lift the gauge. A reading taken on a tie bar looks deeper than the true depth. Move the gauge to the open part of the groove and read again.
Tread depth is one item on the pre-trip inspection. The Pre-Trip Inspection Checklist walks through every tire, wheel and brake item a driver checks before the wheels turn. A tire that passes today can fail next week, so the check belongs in every pre-trip.
What tire defects put a truck out of service?
Section 393.75(a) bans four defects outright. A tire with exposed ply or belt cord, tread or sidewall separation, a flat tire or audible leak, or a cut that exposes ply or belt cord must not run. Each defect is a violation on its own. Each defect also puts the tire on the out-of-service list.
Exposed ply or belt cord means the cord structure shows through the tread or sidewall. The cords are the strength of the tire. Once they show, the tire has no margin left. An inspector who sees cord material puts the vehicle out of service.
Separation is a bulge, blister or split where the tread or sidewall layers come apart. Heat and flex make it grow fast. A small bulge on a repair is allowed up to 3/8 in. Anything larger, or any separation of the tread, is out of service.
A flat tire or audible leak is out of service too. Air escaping from the tread area on a tire with an automatic tire inflation system is different: when the system holds the pressure above half the sidewall maximum, the leak is a violation rather than an out-of-service condition. The checker applies that exception.
Pressure alone can park a truck. A tire at 50 percent or less of the maximum inflation pressure marked on the sidewall is out of service at any position. So is an overloaded tire. So is a tire that touches any part of the vehicle. So is a steer tire marked Not for Highway Use.
Can you run regrooved or retreaded tires on the steer axle?
It depends on the vehicle and the tire type. A bus front wheel allows no regrooved, recapped or retreaded tire at all. Section 393.75(d) bans all three on the front wheels of a bus. The ban is absolute. A bus with a retread on a front wheel is out of service.
A truck or truck-tractor front wheel allows recapped and retreaded tires. It bans regrooved tires rated 4,920 lb or more. Section 393.75(e) sets that line at a load-carrying capacity of 2,232 kg, which is 4,920 lb. A regrooved tire rated below 4,920 lb passes the operating rule on a truck front wheel.
The annual inspection standard is stricter. Part 396 Appendix A item 10(a)(9) fails any regrooved tire on a steering axle, whatever the rating. The only exception is a vehicle used solely in urban or suburban service. A regrooved steer tire that passes the operating rule can still fail the annual inspection.
Regrooving, recapping and retreading are three different processes. Regrooving cuts new grooves into a worn tire casing. Recapping and retreading replace the tread band on a used casing. The rules treat regrooving more strictly than retreading on the steer axle, because regrooving cuts into the casing itself.
Check the sidewall before you buy or mount a steer tire. A regrooved tire is marked as regrooved. A retread is marked with the retreader name and the retread date. When the marking is unclear, treat the tire as regrooved and keep it off the steer axle.
What are the tire load rules?
A tire must not carry more than its rated load. Section 393.75(g) sets the limit at the load marked on the sidewall or the load in the FMVSS 119 publication for that tire. Whichever rating applies, the load on the tire must stay at or below it. An overloaded tire is out of service at any position.
Under-inflation counts as overload. A tire that is low on pressure cannot carry its rated load. The annual inspection standard fails a tire when the weight exceeds the load limit, including when the excess comes from low pressure. A tire that is 20 psi low may be overloaded even when the scale weight looks fine.
One exception exists. A vehicle with a state special permit may run an overloaded tire when the speed stays at or below 50 mph. Both conditions must hold: the permit and the speed limit. A permit alone does not help at 65 mph. A slow speed alone does not help without the permit.
Manufactured homes follow a separate rule in section 393.75(h). A home built before 2002 may run tires overloaded by up to 18 percent, but an overload of 9 percent or more limits the speed to 50 mph. A home built in 2002 or later allows no overload at all. This checker does not cover manufactured homes.
Find the rating on the sidewall. The sidewall shows the maximum load in pounds or kilograms, often next to the load index number. The FMVSS 119 publication lists the same ratings by tire size. The sidewall marking governs when it is present. The FMVSS 119 publication rating applies only when the sidewall carries no marking.
How do you check cold tire inflation pressure?
Cold pressure is the pressure of a tire that has not been driven. Section 393.75(i)(1) requires the cold inflation pressure to be at least the pressure specified for the load on the tire. The pressure specified for the load comes from the tire maker load and inflation tables. It is not the maximum pressure on the sidewall.
Measure cold when you can. A tire that has sat for three hours or more, or has been driven less than one mile, counts as cold. The gauge reading is the cold pressure. No correction is needed. This is the simplest check and the one inspectors prefer.
When the tire is warm, use Table 1. Section 393.75(i)(2) lets you estimate cold pressure by subtracting the heat buildup in Table 1 from the measured pressure. Table 1 has one row only: 41-55 mph average speed in the previous hour. Subtract 5 psi for a tire rated 4,000 lb or less. Subtract 15 psi for a tire rated over 4,000 lb.
No other speed row exists in the current regulation. The table gives no correction for a 30 mph average or a 65 mph average. A warm reading outside 41-55 mph cannot be corrected with the table. Let the tire cool and measure again, or wait for a cold reading before you decide.
A worked example shows the math. A tire measured at 110 psi after driving at a 50 mph average, rated over 4,000 lb, has a Table 1 buildup of 15 psi. The estimated cold pressure is 95 psi. When the pressure specified for the load is 95 psi, the tire passes. When it is 100 psi, the tire fails.
Pressure also has an out-of-service line. A tire at 50 percent or less of the maximum inflation pressure marked on the sidewall is out of service. A tire with a 120 psi sidewall maximum is out of service at 60 psi or below. Check the sidewall maximum and do the math before every trip.
What is a speed-restricted tire?
A speed-restricted tire is a tire labeled for a maximum speed of 55 mph or less. The label follows FMVSS 119 S6.5(e). The tire is built for low-speed service, often on a vehicle that runs short local routes. The sidewall label states the speed limit in plain numbers.
Section 393.75(f) bars operating a speed-restricted tire above its rated limit. A tire labeled 55 mph must not run at 60 mph. The limit follows the tire, not the vehicle. Moving the tire to a faster vehicle does not change the limit.
The annual inspection standard adds a second test. Part 396 Appendix A item 10(c) fails a speed-restricted tire unless the motor carrier specifically designated it for the vehicle. A carrier that runs speed-restricted tires must designate them in writing for each vehicle. A tire without that designation fails the inspection even when it never exceeded its speed limit.
Speed-restricted tires are rare on long-haul trucks. They appear on local delivery vehicles, yard trucks and some specialty equipment. A driver who picks up a rental or a replacement truck should check the sidewall labels before the first highway run. A 55 mph tire on a 70 mph run is a violation waiting for an inspector.
How do tire violations count against your CSA score?
Tire violations land in the Vehicle Maintenance BASIC. The FMCSA Safety Measurement System gives most tire violations a severity weight of 8. That covers exposed ply or belt cord, separation, a flat tire or leak, a cut, low tread depth and a speed rating violation. The high weight reflects the crash risk of a tire failure at highway speed.
Load violations weigh less. The Tire vs Load group carries a severity weight of 3. That covers an overloaded tire, including overload from under-inflation. It also covers a regrooved tire on a front wheel. The weight is lower, but the violation still counts for 24 months.
An out-of-service order adds 2 to the severity weight. A severity 8 tire violation with an out-of-service order counts as 10. Time weights multiply the result: 3 times for a violation in the last 6 months, 2 times for 6 to 12 months, 1 time for 12 to 24 months. A fresh out-of-service tire violation hits the score hard.
The CSA Violation Points Checker works out the severity weight, the BASIC, the time weight and the day the violation falls off the 24-month window for any violation code.
A wrong tire violation can be challenged through DataQs. The DataQs Challenge Helper walks through the three-stage review and the deadlines for each stage. The FMCSA Fine Calculator shows the maximum civil penalty for a tire violation under 49 CFR Part 386.
What did the 2026 Roadcheck find about tires?
Tires were the second most common out-of-service violation at Roadcheck 2026. Inspectors ran 54,575 inspections across the United States, Canada and Mexico on May 12-14, 2026. They put 10,350 vehicles out of service, which is 19 percent of all inspections.
Of the 44,047 Level I, II and V inspections, 23.5 percent ended out of service. Those inspections produced 13,924 out-of-service vehicle violations. Tires accounted for 2,914 of them, or 20.9 percent. Only brake systems produced more, with 3,379 violations at 24.3 percent.
The United States numbers were worse. US inspectors recorded 2,669 tire out-of-service violations, which is 22.3 percent of US out-of-service vehicle violations. Canada recorded 235 at 12.2 percent. Mexico recorded 10 at 20.4 percent. The 2025 Roadcheck found 2,899 tire violations at 21.4 percent, so the tire problem did not improve.
Brakes and tires together caused nearly half of all out-of-service vehicle violations. The Brake Inspection Readiness Checker runs a brake system against the inspection standard. The Brake Pushrod Stroke Checker measures pushrod stroke against the readjustment limit for each chamber size.
The message for drivers is simple. A tire check takes minutes. A tire out-of-service order takes hours and costs a load. The pre-trip inspection is the cheapest tire program a carrier can run.
How do you use the Tire Compliance Checker?
- Pick the tire position and the vehicle type. Enter the tread depth at the lowest point in 32nds of an inch.
- Answer the two out-of-service questions: two adjacent grooves below 2/32 in for a steer tire, three separate spots below 1/32 in for other tires.
- Check every defect you can see: exposed ply or belt cord, separation, a flat tire or leak, a cut, a Not for Highway Use marking and the annual inspection extras.
- Pick the tire type and say whether the vehicle runs solely in urban or suburban service. Enter the load and the sidewall rating when you know them.
- Enter the measured pressure and say whether the tire was cold or warm. Add the average speed, the required cold pressure and the sidewall maximum when you know them.
- Read the verdict, the check table, the figures and the notes. Copy the summary for the vehicle file, or reset the checker to start over.
Frequently asked questions
What is the minimum tread depth for a truck steer tire?
4/32 in at any point on a major tread groove. Section 393.75(b) sets that line for the front wheels of a bus, truck or truck-tractor. The depth is never measured at tie bars, humps or fillets. A steer tire below 4/32 in fails the federal rule.
What is the out-of-service tread depth for a steer tire?
Below 2/32 in in two adjacent major grooves at the same spot. That is the CVSA out-of-service line, not 4/32 in. Four thirty-seconds is the FMCSR legal minimum. A steer tire at 3/32 in is a violation but not out of service.
Can you run retreaded tires on the steer axle?
On a truck or truck-tractor, yes. Section 393.75(e) bans only regrooved tires rated 4,920 lb or more on truck and truck-tractor front wheels. Recapped and retreaded tires are allowed. On a bus, no regrooved, recapped or retreaded tire is allowed on a front wheel. The annual inspection standard also fails any regrooved tire on a steering axle, except on a vehicle used solely in urban or suburban service.
How do you estimate cold tire pressure from a warm reading?
Subtract the Table 1 heat buildup from the measured pressure. Table 1 has one row only: 41-55 mph average speed in the previous hour. Subtract 5 psi for a tire rated 4,000 lb or less and 15 psi for a tire rated over 4,000 lb. Outside 41-55 mph the regulation gives no correction, so measure the tire cold.
What pressure puts a tire out of service?
A tire at 50 percent or less of the maximum inflation pressure marked on the sidewall is out of service at any position. A tire with a 120 psi sidewall maximum is out of service at 60 psi or below. Cold pressure below the pressure specified for the load is a violation, not an out-of-service condition, unless it also crosses the 50 percent line.
Are tire violations serious for a CSA score?
Yes. Most tire violations carry a severity weight of 8 in the Vehicle Maintenance BASIC. An out-of-service order adds 2. Time weights multiply the result by 3 in the first 6 months, by 2 in months 6 to 12 and by 1 in months 12 to 24. A violation falls off after 24 months.
Related tools
- Pre-Trip Inspection Checklist: check every tire, wheel and brake item before the wheels turn.
- Brake Inspection Readiness Checker: run a brake system against the inspection standard before Roadcheck season.
- CSA Violation Points Checker: see the severity weight, the BASIC, the time weight and the day a violation falls off the 24-month window.
- Steering Lash Checker: measure steering lash against the limit for your wheel diameter.
- Brake Pushrod Stroke Checker: measure pushrod stroke against the readjustment limit for each chamber size.
- DataQs Challenge Helper: challenge a wrong tire violation through the three-stage DataQs review.
- Trucking Tools: browse every free calculator on Trucking Mind.
Sources
- 49 CFR 393.75, Tires. ecfr.gov/current/title-49/section-393.75 Accessed November 19, 2026.
- 49 CFR Part 396, Appendix A to Part 396, Minimum Periodic Inspection Standards, item 10. ecfr.gov/current/title-49/appendix-Appendix A to Part 396 Accessed November 19, 2026.
- 49 CFR 396.9, Inspection of motor vehicles in operation. ecfr.gov/current/title-49/section-396.9 Accessed November 19, 2026.
- CVSA, 2026 Roadcheck Results. cvsa.org/news/2026-roadcheck-results Accessed November 19, 2026.
- CVSA, Issue 21-016-VEH, Out-of-Service Criteria. cvsa.org/issues/21-016-VEH Accessed November 19, 2026.
- FleetOwner, FMCSA, CVSA and tread depth. fleetowner.com/equipment/article/21682772/fmcsa-cvsa-and-tread-depth Accessed November 19, 2026.
- GoDataQs, DOT tire violations under 49 CFR 393.75. godataq.com/guides/dot-tire-violations-393-75 Accessed November 19, 2026.