Skip to main content

Trucking Mind

Two federal sources disagree on the 16 inch power limit. Section 393.209 says 4 1/4 inches. Part 396 Appendix A item 7 says 4 1/2 inches. This checker applies the stricter 4 1/4 inch figure and shows both figures whenever that wheel is checked.

Answer for one truck and one measurement. Every answer updates as you change each field.

Your wheel and your reading

Measure the diameter across the wheel through the center. Most heavy trucks run 18 to 20 inch wheels. The 16 inch row covers wheels 16 inches or smaller. Power steering lash is measured with the engine running.

Steering parts: check each defect you found

Leave every box unchecked when each part looks sound. Check a box only when you found the defect. A checked box is a violation on its own, even when lash passes.

Steering lash passes

Measured 3 in against a 5 1/4 in limit for a 20 in power wheel. The reading is 2 1/4 in inside the FMCSR limit and 4 7/8 in below the CVSA out-of-service line of 7 7/8 in. No steering part defect was checked.

The checks

CheckResultDetail
FMCSR limit (49 CFR 393.209)PassLimit 5 1/4 in for a 20 in power wheel. Measured 3 in. Margin 2 1/4 in.
CVSA out-of-service lineBelow the lineOut-of-service line 7 7/8 in. Measured 3 in. Distance to the line 4 7/8 in.
Engine runningYesPower steering lash is measured with the engine running. This reading was taken correctly.
Steering partsPassNo steering part defect was checked.

The two tiers

TierValueStatus
Your measured lash3 inYour reading
FMCSR limit, 49 CFR 393.2095 1/4 inPass, margin 2 1/4 in
CVSA out-of-service line7 7/8 in4 7/8 in below the line

Next steps

  • Record the reading in the vehicle file with the date and the wheel size.
  • Check lash again at the next pre-trip inspection if steering feel changes.
  • Keep the annual inspection current: Appendix A item 7 covers steering at each periodic inspection.

Notes

  • No extra notes for this result.

This checker applies 49 CFR 393.209, Part 396 Appendix A item 7 and the CVSA out-of-service steering thresholds to your answers. It is not legal advice. Confirm the reading with a second measurement before you rely on a result.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice โ€” check the current regulation and your company policy before you rely on a result.

Quick answer: Steering wheel play limits for a truck come from 49 CFR 393.209. On a 20 inch wheel the limit is 2 1/2 inches for manual steering and 5 1/4 inches for power steering, measured at the rim with the engine running on power steering. This checker compares your reading with the 393.209 limit for your wheel size and steering type, shows how far you sit from the CVSA out-of-service line and checks the steering parts an inspector examines beside lash.

Last reviewed: ยท Focus keyword: steering wheel play limits truck

What is steering wheel lash?

Steering wheel lash is the free play in the steering wheel: the distance the rim moves before the steer tires start to turn. A driver feels it as looseness at the center. The wheel moves, nothing happens, then the tires finally respond. Lash is measured at the rim in inches, or as rotation in degrees.

Some free play is normal. Gears, joints and linkages all have working clearance. The limit in the regulation is the line between normal clearance and worn parts. Past that line the truck wanders, the driver corrects constantly and the steering response gets vague.

Lash grows as parts wear. The gear box wears, tie rod ends loosen, the pitman arm works free on its shaft and U-joints develop play. Each worn part adds a little movement. The checker measures the total at the rim, which is what the inspector measures too.

Lash matters because steering is the one system with no backup. Brakes have two circuits. Tires have a spare. A steering failure leaves the driver with no way to guide the truck. That is why the regulation sets a hard limit and why inspectors treat steering defects seriously.

What are the steering wheel play limits for a truck?

The limits come from 49 CFR 393.209(b). The table gives a maximum rim movement for six wheel diameters, split by manual and power steering. Power steering gets a larger allowance because the hydraulic valve adds its own travel before the tires move.

Steering wheel diameterManual steering limitPower steering limit
16 in or less2 in4 1/4 in
18 in2 1/4 in4 3/4 in
19 in2 3/8 in5 in
20 in2 1/2 in5 1/4 in
21 in2 5/8 in5 1/2 in
22 in2 3/4 in5 3/4 in

The 16 inch row covers wheels 16 inches or smaller. A 15 inch wheel uses the 16 inch limits. A 17 inch wheel is not in the table at all, so the degree rule applies to it. The degree rule is covered in the section below on unlisted diameters.

One row carries a warning. Part 396 Appendix A item 7 lists 4 1/2 inches for a 16 inch power wheel, while section 393.209 lists 4 1/4 inches. The two federal sources disagree. This checker applies the stricter 4 1/4 inch figure and shows the Appendix A figure beside it whenever that wheel is checked.

The limits are maximums, not targets. A reading exactly at the limit passes because the regulation says lash shall not exceed the table value. A reading past the limit by any amount fails, even by 1/8 inch. Measure twice before you trust a borderline reading.

Why do two federal sources disagree on the 16-inch power limit?

The short answer is that one source was updated and the other was not. Section 393.209 was amended in 2005 by 70 FR 48055. That amendment set the 16 inch power limit at 4 1/4 inches and added the 19 inch and 21 inch rows. Appendix A item 7 was never given the same update.

Appendix A still shows the older table. It lists 4 1/2 inches for a 16 inch power wheel and it has only four rows: 16, 18, 20 and 22 inches. It has no 19 inch row and no 21 inch row. It also has no degree rule for diameters outside the table. An inspector using only Appendix A would apply the looser figure to a 16 inch power wheel and would have no row at all for a 19 inch wheel.

Which figure governs? Section 393.209 is the equipment standard. Appendix A sets the minimum standards for the periodic inspection.

A truck that fails section 393.209 is in violation even when it would pass the older Appendix A table. That is why this checker applies the stricter 4 1/4 inch figure for the pass and fail verdict.

The disagreement is narrow but real. It touches only the 16 inch power row. Every other row matches between the two sources. The missing 19 inch and 21 inch rows matter more in practice, because many trucks run those wheel sizes. For those wheels section 393.209 is the only source with a row.

What is the difference between the FMCSR limit and the out-of-service line?

The FMCSR limit is the compliance line. Cross it and the truck is in violation. The out-of-service line is the parking line. Cross it and the inspector puts the truck out of service on the spot. The two lines sit far apart on steering. Confusing them is the most common mistake drivers make about lash.

On a 20 inch wheel with power steering, the FMCSR limit is 5 1/4 inches and the out-of-service line is 7 7/8 inches. A reading of 6 inches fails the regulation but does not park the truck. A reading of 7 7/8 inches parks it. The gap between the lines is the warning zone: legal trouble without a tow bill, but trouble all the same.

Tier, 20 inch wheelManual steeringPower steering
FMCSR limit, section 393.2092 1/2 in5 1/4 in
CVSA out-of-service line5 1/4 in7 7/8 in
Unlisted diameter, FMCSR limit14 degrees30 degrees
Unlisted diameter, out-of-service line30 degrees45 degrees

The wording differs too. Section 393.209 says lash shall not exceed the limit, so a reading exactly at the limit passes. The CVSA criteria say the vehicle is out of service when a value is met or exceeded, so a reading exactly at the out-of-service line parks the truck. The checker applies each rule the way its own source words it.

A violation below the out-of-service line still counts. It goes on the inspection report and it counts against the carrier safety record. It also goes on the driver vehicle inspection report as a defect to repair. Passing the out-of-service line is not the goal. Meeting the FMCSR limit is.

How do you measure steering wheel lash?

Park on level ground with the steer tires straight and the wheels chocked. Start the engine on a power steering truck and let it idle. Mark a reference point on the wheel rim and a fixed point on the column or dash. The measurement is the rim movement between the two points where the tires start to move.

Turn the wheel slowly to the left until the left steer tire just starts to move. Mark that point. Turn slowly to the right until the right steer tire just starts to move. Mark that point.

The distance between the two marks, measured along the rim, is the lash. A tape measure works. A second person watching the tires helps.

Measure at the rim, not at the spokes. The limits are rim measurements. A reading taken halfway to the hub understates the play by half. Measure with the engine running on power steering, because the hydraulic valve changes the feel and the reading. A power reading taken with the engine off proves nothing.

Watch for the rock test on power steering. When wheel movement passes 45 degrees before the tires move, the inspector rocks the wheel between the points of power steering valve resistance. When that rocking motion passes 30 degrees, the vehicle is out of service. The test separates real wear from a valve designed to stay quiet while the truck stands still.

Repeat the measurement once. A single reading can mislead when the tires sit in a rut or the ground slopes. Two readings that agree within 1/4 inch are trustworthy. When they disagree, measure a third time and use the largest reading. The Pre-Trip Inspection Checklist covers the steering free play check beside the rest of the daily walk-around.

What if your steering wheel diameter is not in the table?

Use the degree rule. Section 393.209(b)(2) covers every diameter the table leaves out: lash shall not exceed 14 degrees of angular rotation for manual steering and 30 degrees for power steering. A 17 inch wheel, a 23 inch wheel and every size between the listed rows all use the degree rule.

Degrees measure rotation, not rim distance. A degree is the same angle on any wheel size, which is why the regulation switches to degrees outside the table. A protractor app on a phone gives a usable reading. Mark the wheel, turn to each tire movement point and read the angle between the marks.

The checker converts between inches and degrees when you mix them. An inch reading on an unlisted wheel converts to degrees through the arc formula, using your diameter. A degree reading on a listed wheel converts to inches the same way. The converted value is shown beside the original so the math stays visible.

The out-of-service line for unlisted diameters is 30 degrees manual and 45 degrees power. The same met or exceeded rule applies: a reading exactly at 30 or 45 degrees parks the truck. Note the overlap. The power degree limit under section 393.209 is 30 degrees, which is also the manual out-of-service line. The numbers look similar but they belong to different tiers.

What steering parts does the inspector check besides lash?

Lash is one item in a longer steering check. Section 393.209 covers the wheel, the column, the joints, the gear box, the pitman arm and the power steering system. Appendix A item 7 adds the front axle beam, tie rods, drag links and nuts. A truck can pass the lash test and still fail on a part.

  • Steering wheel: secured, with no spoke cracked through or missing.
  • Steering column: securely fastened, with U-bolts and positioning parts tight.
  • Universal joints and ball-and-socket joints: not worn, not faulty, never repaired by welding.
  • Steering gear box: mounting bolts tight and present, with no cracks in the gear box or brackets.
  • Pitman arm: not loose on the steering gear output shaft.
  • Full travel: wheels turn freely through the limit of travel in both directions.
  • Power steering: all parts operating, no loose or broken parts, belts sound, no leaks, fluid sufficient.
  • Ball and socket motion: more than 1/8 inch by hand is out of service at the roadside, while the annual inspection allows 1/4 inch.
  • Tie rods, drag links and nuts: clamps tight, no looseness in any threaded joint, no nut loose or missing.

The ball and socket numbers deserve a second look. Appendix A item 7(g)(2) fails a vehicle at the annual inspection when linkage motion passes 1/4 inch. The CVSA roadside line is 1/8 inch. The roadside line is tighter than the annual line, which is the reverse of the lash pattern. A joint that passes the annual inspection can still park the truck at the roadside.

Two more items sit in the CVSA steering section. A telescopic steering column must lock into position and a tilt column must lock in at least one position. An auxiliary power assist cylinder separated at either end, allowing more than 1 inch of movement in any direction, is out of service. Check both when the column adjusts or the truck carries an assist cylinder.

Can you drive with steering play over the limit?

No. Section 396.7 bars operating a motor vehicle in a condition likely to cause an accident or a breakdown. Steering play past the limit is exactly that kind of condition. The driver who finds it on a pre-trip inspection must report it and the carrier must repair it before the vehicle operates again.

The repair duty runs through the driver vehicle inspection report. Steering is one of the parts the driver checks before driving under section 392.7 and reports at the end of the day under section 396.11. A defect found on the report must be repaired and certified before the vehicle goes out again. Driving on with a known steering defect is a separate violation on top of the defect itself.

The narrow exception in section 396.7(b) does not help here. A vehicle found unsafe on the highway may continue only to the nearest place where repairs can safely be effected. That is allowed only when moving on is less hazardous than staying put. That covers a defect found on the road. It does not cover starting a trip with a known steering defect.

The cost of ignoring a failed reading goes past the repair bill. A violation on the inspection report counts against the carrier safety record and can feed a safety rating review. The FMCSA Fine Calculator shows the maximum civil penalty for a Part 393 violation. The DOT Record Retention Checker works out how long the inspection report and the repair records must stay on file.

When an inspector places the vehicle out of service, the duties sharpen. No person may operate the vehicle until every repair on the out-of-service notice is complete. The carrier must certify the repair within 15 days, return the completed form when the issuing state agency asks for it and keep a copy for 12 months. That is section 396.9.

How does steering lash show up on a roadside inspection?

Steering is item 10 of the CVSA vehicle inspection. A Level I inspection covers the full vehicle, including the steering mechanism. The inspector measures lash, checks the column, gear box, pitman arm, joints, tie rods and power steering, then records each defect on the Driver Vehicle Examination Report.

A lash reading past the FMCSR limit is recorded as a violation of section 393.209. A reading at or past the out-of-service line adds an out-of-service order: the truck stays put until the steering is repaired. A linkage joint moving more than 1/8 inch by hand is also an out-of-service condition, even when lash itself passes.

The violation counts against the carrier in the CSA Safety Measurement System. Each violation carries a severity weight inside its BASIC and the weight counts triple in its first six months. The CSA Violation Points Checker shows the weight for any code and the day it falls off the 24-month window. The Safety Rating Explainer shows how repeated violations feed a rating review.

Steering rarely tops the out-of-service counts. Brakes and tires park far more trucks. That is no comfort when the truck parked is yours. The same walk-around that catches lash catches the bigger categories too: the Brake Pushrod Stroke Checker covers chamber stroke and lining, while the Tire Compliance Checker covers tread depth and tire condition. The Brake Inspection Readiness Checker covers the 20 percent defective brake rule.

What causes excess steering play and how is it fixed?

Wear causes most excess lash. The steering gear box wears where the worm and sector meet. Tie rod ends and drag link ends wear at the ball studs. The pitman arm loosens on the output shaft splines. U-joints in the column develop play. Each worn part adds movement and the total shows at the rim.

Adjustment fixes some wear and hides the rest. Many gear boxes have a lash adjuster that takes up worm and sector play. An adjustment that removes play at the center but binds at full lock has gone too far. When adjustment cannot restore free movement through full travel, the gear box needs replacement.

Joints and linkages are replaced, not adjusted. A worn tie rod end gets a new end. A loose pitman arm gets reseated or replaced with its nut torqued to the manufacturer figure. A weld repaired joint is a violation in itself under section 393.209(d): welding a steering joint is never an acceptable repair.

After any steering repair, retest lash and check the alignment. A repair that changes tie rod length changes toe. Wrong toe wears steer tires fast. Road test at low speed first, then check lash again with the engine running. Record the new reading with the repair in the vehicle file.

How often should you check steering lash?

Check steering feel every day and measure lash whenever the feel changes. Section 392.7 lists steering among the parts the driver must inspect before driving. Section 396.13 requires the driver to be satisfied the vehicle is in safe operating condition before driving. A daily check takes two minutes: rock the wheel with the engine running and feel for new play.

Measure lash with a tape at least once a month on a working truck. Monthly readings build a trend. A reading that grows by 1/2 inch over three months points at a wearing part before it fails the limit. Record each reading with the date and the mileage so the trend is visible.

Measure before every annual inspection. Appendix A item 7 covers steering at each periodic inspection. A failed reading at the inspection means a second visit. A pre-check in the yard costs nothing and catches the failure early. Keep the periodic inspection current: every commercial motor vehicle needs one at least once every 12 months.

Measure after any steering work, any front end impact and any time the truck pulls, wanders or shudders. A curb strike can bend a tie rod without leaving a mark. A new gear box can arrive out of adjustment. The post-repair reading is the proof the work fixed the problem.

How do you use the Steering Lash Checker?

  1. Enter your steering wheel diameter in inches and pick manual or power steering.
  2. Enter your measured lash at the rim in inches or degrees.
  3. Say whether the engine was running for the reading.
  4. Check each steering part defect you found, or leave every box unchecked when each part looks sound.
  5. Read the verdict, the check table, the two tier table and the next steps.
  6. Copy the summary for the vehicle file, or reset the checker to start over.

Frequently asked questions

How much steering wheel play is allowed on a truck?

On a 20 inch wheel, 2 1/2 inches for manual steering and 5 1/4 inches for power steering, measured at the rim under 49 CFR 393.209. The limit moves with wheel size: 2 inches manual and 4 1/4 inches power on a 16 inch wheel, up to 2 3/4 inches manual and 5 3/4 inches power on a 22 inch wheel. Diameters outside the table use 14 degrees manual and 30 degrees power.

What is the out-of-service limit for steering wheel play?

On a 20 inch wheel, 5 1/4 inches for manual steering and 7 7/8 inches for power steering. A reading at or past the line puts the vehicle out of service under the CVSA criteria. For diameters outside the table the line is 30 degrees manual and 45 degrees power. The out-of-service line is looser than the 393.209 limit, so a truck can fail the regulation without being parked.

Why does Appendix A list 4 1/2 inches for a 16-inch power wheel?

Appendix A item 7 was never updated after section 393.209 was amended in 2005. The amendment set the 16 inch power limit at 4 1/4 inches and added the 19 inch and 21 inch rows. Appendix A still shows the older 4 1/2 inch figure with only four rows. This checker applies the stricter 4 1/4 inch figure and shows the Appendix A figure beside it.

Do you measure power steering play with the engine running?

Yes. Appendix A item 7(a) and the CVSA criteria both require the engine running for a power steering lash reading. A power reading taken with the engine off is not valid. Manual steering has no engine-running rule.

What if my steering wheel is 17 inches?

A 17 inch wheel is not in the 393.209 table, so the degree rule applies: 14 degrees for manual steering and 30 degrees for power steering. Measure the rotation in degrees, or enter an inch reading and let the checker convert it. The out-of-service line for unlisted diameters is 30 degrees manual and 45 degrees power.

Can I drive with steering play over the limit?

No. Section 396.7 bars operating a vehicle in a condition likely to cause an accident or a breakdown. Report the defect on the driver vehicle inspection report and have it repaired before the next trip. A reading at or past the CVSA out-of-service line parks the vehicle until the repair is complete.

Related tools

Sources

  1. 49 CFR 393.209, Steering wheel systems. ecfr.gov/current/title-49/section-393.209 Accessed November 19, 2026.
  2. 49 CFR Part 396, Appendix A, Minimum Periodic Inspection Standards. ecfr.gov/current/title-49/part-396/appendix-A Accessed November 19, 2026.
  3. 49 CFR 396.9, Inspection of motor vehicles and intermodal equipment in operation. ecfr.gov/current/title-49/section-396.9 Accessed November 19, 2026.
  4. 49 CFR 396.13, Driver inspection. ecfr.gov/current/title-49/section-396.13 Accessed November 19, 2026.
  5. CVSA North American Standard Out-of-Service Criteria, 2004 edition, Part II item 10, Steering Mechanisms. law.resource.org/pub/us/cfr/ibr/003/cvsa.out-of-service.2004.pdf Incorporated by reference at 49 CFR 385.415(b)(1). Accessed November 19, 2026.
  6. FleetOwner, CVSA updates out-of-service criteria to improve safety and compliance, April 3, 2026. fleetowner.com/safety/news/55368417/cvsa-updates-out-of-service-criteria-to-improve-safety-and-compliance Accessed November 19, 2026.
Follow on WhatsApp Ask by Voice