Skip to main content

Trucking Mind

This tool checks the combination against the frozen LCV table, not the axles. It tests triples, Rocky Mountain doubles, turnpike doubles, plus STAA twins against the state-by-state limits in 23 CFR Part 658 Appendix C: cargo length, overall length, gross weight, routes, plus permits. It does not check axle weights or the bridge formula. A combination that passes here can still fail on its axles.

Pick the configuration, enter the trailer lengths plus the weight, then pick every state on the route. Every answer updates the result as you change each field. All lengths are in feet. All weights are in pounds.

The combination

The third trailer length matters only for triples. Enter each trailer in feet, front to rear. The tractor length sets the overall length estimate: a conventional tractor runs about 19 ft, a cabover about 13 ft.

Measured lengths, when known

Leave either field blank to use the estimate. Cargo-carrying length is measured from the front of the first cargo unit to the rear of the last, including the gaps between units. The estimate adds 4 ft per coupling gap. Overall length is measured bumper to bumper. The estimate adds the tractor length to the cargo length, then subtracts 3 ft for the fifth-wheel overlap. Measure the rig when the estimate sits near a state limit.

Weight and load

The axle count matters for New York, where the weight limit turns on axles: 9 axles 143,000 lb, 8 axles 138,400 lb. Loaded or empty matters for Nebraska, where triples plus long doubles must travel empty over 65 ft of cargo.

States on the route

Pick every state the rig will enter. Hold Ctrl or Command to pick more than one state. For Missouri or Iowa, also pick the state the rig enters from: the limits there turn on the state of entry. A state left out of the list is a state left unchecked.

Legal in all 4 states checked.

4 legal, 0 not legal, 0 check across 4 states.

This triples combination at 93.5 ft cargo and 105,500 lb is legal in every state checked, on the routes and permits in the table below. The weight still has to satisfy the bridge formula on the axles actually run.

The checks

StateResultDetail
IdahoLegalLegal to 105,500 lb. Routes: All NN routes. Permit: Annual permit, fee charged. Same routes, permit and off-tracking rules as doubles.
MontanaLegalLegal to 131,060 lb. Routes: Interstate System routes. Permit: Special triple permit, annual or trip. 100 ft cargo and 110 ft overall with a conventional tractor; 95 ft and 105 ft with a cabover. 55 mph maximum. No travel in adverse weather. No Class A explosives. Driver must be company certified.
NevadaLegalLegal to 129,000 lb. Routes: All NN routes except US 93 from NV SR 500 to Arizona. Permit: LCV authority through the cab-card weight declaration (12-month LCV permit, NAC 706.156). Same conditions as doubles.
UtahLegalLegal to 129,000 lb. Routes: 85 ft or less: all NN. Over 85 ft: I-15, I-70, I-80, I-84, I-215, UT-201. Permit: LCV authority from the UDOT Motor Carrier Division. Triples follow the over-85 ft route list. Same LCV authority and weather rules as doubles.

The figures

FigureValueNote
ConfigurationTriplesSTAA twins, triples, Rocky Mountain double or turnpike double.
Trailer lengths28.5 ft, 28.5 ft, 28.5 ftEach trailer in feet, front to rear.
Cargo-carrying length93.5 ft (estimated)Front of the first cargo unit to rear of the last. Estimated as trailer lengths plus 4 ft per coupling gap unless a measured length was entered.
Overall length109.5 ft (estimated)Estimated as tractor length plus cargo length minus 3 ft of fifth-wheel overlap unless a measured length was entered.
Gross weight105,500 lbThe weight the state caps are tested against. Axle weights and the bridge formula still apply.
Axles in the combination9New York weight depends on axle count: 9 axles 143,000 lb, 8 axles 138,400 lb.
Lowest weight cap on this route105,500 lbThe lowest state maximum among the states where this configuration is legal. The rig must satisfy every state cap, not just the lowest.
States checked4Idaho, Montana, Nevada, Utah.

What to do

  • Get the permit for each legal state before you roll: Idaho, Montana, Nevada, Utah.
  • Carry the T endorsement (double/triple trailers) on the CDL plus the LCV driver-training certificate for this configuration.
  • Measure the cargo-carrying length: the estimate sits within 2 ft of a state limit.
  • Confirm the route with each state DOT or permit office before you roll. States may restrict LCV routes further without changing Appendix C.

Before you roll

  • CDL with the T endorsement (double/triple trailers). The endorsement needs a knowledge test only, under 49 CFR 383.93(c)(1).
  • LCV driver-training certificate for doubles or triples, under 49 CFR Part 380 Subpart B. The grandfathering window closed in 2005, so training is the only route for a new LCV driver.
  • State permits in the cab, plus the cab-card weight declaration where the state runs LCV authority that way (Nevada).
  • Measured cargo-carrying length and overall length, written on the trip sheet, when the rig sits near a state limit.
  • Axle weights from a scale ticket, checked against the bridge formula. A state maximum is a ceiling, not a promise that the axles are legal.

Notes

  • The 1991 freeze: an LCV configuration may operate only where state law authorized it and it was in actual lawful operation on or before June 1, 1991 (23 USC 127(d)). No state can add a new LCV configuration or route. States can only restrict further.
  • STAA twin 28s are legal on the National Network in all 50 states at 80,000 lb or less. The freeze does not touch them.
  • Cargo-carrying length is estimated as the trailer lengths plus 4 feet per coupling gap. Wyoming law counts the connecting mechanism inside its 81 ft limit. The estimate follows that reading. Measure the rig when the estimate sits near a limit.
  • Overall length is estimated as tractor length plus cargo length minus 3 feet of fifth-wheel overlap. Enter a measured overall length for an exact check.
  • State maximum weights sit under the federal bridge formula and the state axle limits. This tool does not check axle weights.
  • State table: 23 CFR Part 658 Appendix C, read 19 Nov 2026, plus current state DOT checks for Oregon, Utah, Nevada, Indiana, Massachusetts and Wyoming. Re-check the table at the next review, around 18 May 2027.

This tool applies 23 CFR Part 658 Appendix C plus 23 USC 127(d) to your inputs. Confirm the result against the state DOT or permit office before acting. A measurement taken wrong gives a wrong verdict, so re-measure any figure that sits close to a limit.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is a planning estimate based on the published text of 23 CFR Part 658 Appendix C plus 23 USC 127(d), not legal advice — confirm the route, the weight, plus any permit with each state DOT or permit office before you roll.

Quick answer: Seventeen states allow triples: Alaska, Arizona, Colorado, Idaho, Indiana, Iowa, Kansas, Missouri, Montana, Nebraska, Nevada, North Dakota, Ohio, Oklahoma, Oregon, South Dakota, plus Utah. Every one of them allows triples only because it authorized them before the federal freeze of June 1, 1991. Each state caps the length, the weight, plus the routes its triples may use. The heaviest triples run in Montana at 131,060 lb. The longest run in Colorado at 115.5 ft of cargo. Nebraska triples must travel empty, Iowa triples run only in the Sioux City zone. Missouri triples depend on the state of entry. STAA twin 28s are a different story: they are legal on the National Network in all 50 states at 80,000 lb or less. The 1991 freeze does not touch them. This checker tests any triples, Rocky Mountain double, turnpike double, or STAA twin combination against every state on the route, then names the routes, the weight caps, plus the permits for each state.

Last reviewed: · Focus keyword: states that allow triples

Which states allow triples?

Seventeen states allow triples. The list is fixed by federal law. It cannot grow. Each state on it authorized triples under state law plus had them in actual lawful operation on or before June 1, 1991, which is the test Congress set in 23 USC 127(d). A state that misses either part of that test cannot allow triples today, whatever its legislature might want. The seventeen are Alaska, Arizona, Colorado, Idaho, Indiana, Iowa, Kansas, Missouri, Montana, Nebraska, Nevada, North Dakota, Ohio, Oklahoma, Oregon, South Dakota, plus Utah.

The list needs three qualifications before it is useful. Nebraska triples must travel empty: the state allows three-trailer combinations only without cargo, on I-80 between the Wyoming line plus Exit 440, at 80,000 lb or less. Iowa triples run only in the Sioux City zone, entering from South Dakota, on I-29 plus I-129. Missouri triples depend on the state of entry: from Kansas the limit is 109 ft of cargo at 120,000 lb, while from Oklahoma it is 95 ft at 90,000 lb. A triples rig that is legal in one of these states can be illegal a few miles down the road, which is why the checker asks for every state on the route plus the state of entry for Missouri plus Iowa.

StateMax cargo lengthMax gross weightKey limit
Alaska110 ftNo Interstate capMay 1 to Sep 30, 400 hp, 10 years Alaska experience
Arizona95 ft123,000 lb129,000 lb on I-15 only
Colorado115.5 ft110,000 lbRush-hour bans in Denver, Colorado Springs, plus Pueblo
Idaho95 ft105,500 lbAll National Network routes, annual permit
Indiana104.5 ft127,400 lbIndiana Toll Road plus I-80 and I-90 segments
Iowa100 ft129,000 lbSioux City zone only, entering from South Dakota
Kansas109 ft120,000 lbKansas Turnpike; SVC triples I-70 Colorado to Goodland
Missouri109 ft120,000 lbFrom Kansas; from Oklahoma 95 ft at 90,000 lb
Montana100 ft131,060 lb110 ft overall conventional, 95 plus 105 ft cabover
Nebraska95 ft80,000 lbEmpty only, I-80 Wyoming to Exit 440, 105 ft overall
Nevada95 ft129,000 lbLCV authority through the cab-card weight declaration
North Dakota100 ft105,500 lbSingle-trip permit over 80,000 lb, LONG LOAD sign
Ohio95 ft115,000 lbOhio Turnpike plus the 1-mile SR 7 segment, 90 to 105 ft overall
Oklahoma95 ft90,000 lbEach trailer 29 ft or less
Oregon96 ft105,500 lb105 ft overall limit binds first for standard pups
South Dakota100 ft129,000 lbTrailers 45 ft or less at 81.5 ft cargo or less, 48 ft above
Utah95 ft129,000 lbInterstates plus freeways only, LCV authority required

The weight range across the seventeen is wide: 80,000 lb in Nebraska to 131,060 lb in Montana. The length range is wide too: 95 ft of cargo in most western states to 115.5 ft in Colorado. A triples rig built for Montana at 131,060 lb is overweight in every other triples state except South Dakota, Nevada, Utah, plus Iowa from South Dakota, all at 129,000 lb. A rig built for Colorado at 115.5 ft of cargo is over length everywhere else. The practical triples rig is a compromise: three 28.5 ft pups at 93.5 ft of cargo, which fits the cargo limit in every triples state, at a weight set by the lowest cap on the route.

Two cautions belong with any triples list found online. First, secondary tables disagree with each other by thousands of pounds plus several feet, because they mix the frozen Appendix C figures with current state program figures plus with overall length figures. The figures in this checker come from Appendix C itself, read in full, plus from current state DOT sources where a state program has moved since the appendix was last amended. Second, the Federal Highway Administration publishes a map with the caption 17 States that in fact lists 22 LCV states, because it counts the six doubles-only states alongside the sixteen triples states it names. Its triples list also includes Nebraska without noting that Nebraska triples travel empty only. Treat any single secondary list as a starting point, then verify against Appendix C plus the state DOT.

The states that do not allow triples are the other thirty-three plus the District of Columbia. That includes the whole East Coast south of New York, the whole Southeast, plus Texas, California, plus Illinois. A triples rig heading east must break down before the first non-triples state line. The usual break-down points are the staging areas on the edge of the triples region: eastern Kansas, eastern Nebraska, eastern South Dakota, plus the Ohio Turnpike gates. The checker names the first not-legal state on the route so the break-down point can be planned before the trip starts.

What is a longer combination vehicle?

A longer combination vehicle, an LCV, is defined by statute, not by habit. Under 23 USC 127(d)(4), an LCV is a truck tractor plus two or more trailers or semitrailers operating on the Interstate System at a gross vehicle weight over 80,000 lb. Three parts of that definition matter. The combination must have a tractor plus at least two trailing units. It must operate on the Interstate System. Its gross weight must exceed 80,000 lb. A tractor plus two trailers at 80,000 lb or less is not an LCV under the definition, even though it looks like one. A tractor plus two trailers on a non-Interstate highway is not an LCV under the definition either, even at 120,000 lb, though state law still governs it.

Three common LCV forms cover nearly every combination on the road. Triples are a tractor plus three trailers, usually three 28.5 ft pups, which is the standard triples rig across the West. A Rocky Mountain double is a tractor plus a long lead semitrailer, typically 40 to 48 ft, plus a short pup, typically 26 to 28.5 ft. A turnpike double is a tractor plus two long trailers, typically 40 to 48 ft each, named for the turnpikes where it usually runs. The Doubles Calculator works out the length plus weight figures for a two-trailer combination before it is checked here.

Two lengths govern every LCV. Confusing them is the most common error in route planning. Cargo-carrying length is the measure Appendix C uses for most states: the distance from the front of the first cargo unit to the rear of the last, including the gaps between the units. Overall length is the distance from the front bumper to the rear bumper of the whole combination, which adds the tractor plus the fifth-wheel overlap. A triples rig with three 28.5 ft pups carries 93.5 ft of cargo (85.5 ft of trailers plus 8 ft of coupling gaps) but measures about 109.5 ft overall behind a 19 ft conventional tractor. Oregon shows why both matter: its triples cargo limit is 96 ft, which the standard rig passes, but its overall limit is 105 ft, which the same rig fails.

The checker estimates both lengths from the trailer lengths plus the tractor length, then lets a measured figure override either estimate. The cargo estimate adds 4 ft per coupling gap: one gap for a double, two for a triple. The overall estimate adds the tractor length to the cargo length, then subtracts 3 ft for the fifth-wheel overlap, which is the part of the lead trailer that sits over the tractor. Wyoming law confirms the gap-inclusive reading: its 81 ft limit expressly includes the connecting mechanism. When the estimate sits within 2 ft of a state limit, the checker says so, because a tape measure is the only honest answer that close to the line.

Weight is the third limit. It sits under two more rules that this checker does not test. The state maximum in Appendix C is a ceiling on gross weight, but the federal bridge formula plus the state axle limits govern how that weight may sit on the axles. A rig at the Montana maximum of 131,060 lb still needs its axles spaced plus loaded to satisfy Formula B, with no single axle over 20,000 lb plus no tandem over 34,000 lb on the Interstate. The Bridge Formula Axle Weight Checker tests the axle side. The Federal Size Limits Checker tests the federal size floor that every state must allow. Run all three before a heavy LCV trip.

What is the 1991 freeze that stops any new state joining?

The freeze is the Intermodal Surface Transportation Efficiency Act of 1991, known as ISTEA, which Congress wrote into 23 USC 127(d). Before ISTEA, a state could authorize longer or heavier combinations on its own. After ISTEA, the door closed. Section 127(d)(1)(A) allows an LCV to operate only when the configuration was authorized by state law plus in actual lawful operation on or before June 1, 1991. Both parts must be true. A state that authorized triples in 1990 but had none running by June 1, 1991 fails the test. A state where triples ran in 1990 without a state law authorizing them fails it too. The two-part test is why the list of triples states has not changed in thirty-five years.

Section 127(d)(1)(B) freezes the limits as well as the list. An LCV operating under the freeze stays subject to the state limits in force on June 1, 1991, for its length, its weight, plus its routes, with only minor adjustments allowed for a temporary or emergency situation. A state cannot raise its triples weight cap, lengthen its triples routes, or add a new LCV configuration. It can only hold the line or restrict further. That is why Appendix C still governs: it is the frozen record of what each state allowed on the freeze date, published as an appendix to 23 CFR Part 658.

Congress wrote four narrow exceptions into the freeze. Each one is worth knowing by name. Wyoming got its own paragraph, section 127(d)(1)(C): configurations authorized by Wyoming state law by November 3, 1992, within the limits of section 127(a), at 117,000 lb or less. Ohio got a one-mile segment, section 127(d)(1)(D): triples of three 28.5 ft trailers on the one mile of State Route 7 south of Ohio Turnpike exit 16. Alaska got its own date, section 127(d)(1)(E): LCVs in actual operation prior to July 5, 1991. Iowa got two highway segments, section 127(d)(1)(F): I-29 from Sioux City to the South Dakota border plus I-129 from Sioux City to the Nebraska border. Every other LCV operation in the country traces to the June 1, 1991 test.

The Alaska dates deserve a precise note, because the statute plus the appendix differ by one day. The statute says LCVs in actual operation prior to July 5, 1991. The Appendix C introduction says the Alaska values are frozen as of July 6, 1991. Both dates describe the same freeze: the statute sets the operation test at July 5, while the appendix records the values as they stood on July 6. The checker states both dates exactly as each source gives them, rather than smoothing the difference away.

The practical consequence of the freeze is that LCV route planning is a historical exercise. The question is never what a state wants to allow today. It is what the state allowed plus had running on June 1, 1991. That is also why the figures in this checker are stable: the appendix was last amended on August 22, 2019, at 84 FR 43688. The amendment did not add a state or a configuration. What changes is state administration around the frozen figures: permit offices, route designations, plus program rules. The checker tracks those through current state DOT sources, with the review date shown at the top of this page.

What is a Rocky Mountain double?

A Rocky Mountain double is a tractor plus a long lead semitrailer plus a short pup trailer. The lead trailer typically runs 40 to 48 ft. The pup typically runs 26 to 28.5 ft. The combination takes its name from the mountain states where it grew up: the long lead trailer carries the bulk of the freight, while the pup adds capacity without the handling penalty of a second long trailer on mountain grades plus in winter wind. A standard Rocky Mountain double with a 48 ft lead plus a 28.5 ft pup measures 80.5 ft of cargo, which fits the cargo limit in every doubles state except Oregon plus Washington, where the doubles cargo limit is 68 ft.

Every one of the 27 Appendix C states allows some form of double, so the Rocky Mountain double has the widest legal footprint of any LCV. The limits vary sharply by state. Wyoming allows 81 ft of cargo at 117,000 lb, with the 81 ft expressly including the connecting mechanism under W.S. 31-18-802, the lead semitrailer capped at 48 ft plus the rear trailer at 40 ft. Montana allows 93 ft at 131,060 lb. Utah plus Nevada allow 95 ft at 129,000 lb. Idaho allows 95 ft at 105,500 lb on all National Network routes. At the short end, Oregon plus Washington allow only 68 ft of cargo at 105,500 lb, which fits a 40 ft lead plus a 24 ft pup but not the standard 48 ft plus 28.5 ft rig.

Several states add per-trailer limits that bind before the cargo limit does. Nevada caps each trailer at 48 ft, plus when one trailer is 48 ft the other may not exceed 42 ft, so a 48 ft plus 43 ft rig fails even though its 95 ft of cargo fits the state limit. South Dakota caps each trailer at 45 ft when the cargo runs 81.5 ft or less, rising to 48 ft above 81.5 ft of cargo. Oregon caps the lead trailer at 40 ft plus the second trailer at 35 ft. The checker tests every per-trailer limit in Appendix C before it tests the cargo length, so a rig that fails on one trailer gets the exact reason named.

Two states need special care with a Rocky Mountain double. Nebraska caps loaded doubles at 65 ft of cargo, with a 71.5 ft allowance for seasonal harvest loads, while empty doubles may run to 95 ft of cargo on I-80 between the Wyoming line plus Exit 440. Over 65 ft to 85 ft of cargo, the rear trailer must be 26 ft to 28 ft. Over 85 ft of cargo, the trailers must be about equal in length. Missouri sets its doubles limits by the state of entry: from Kansas 109 ft at 120,000 lb, from Oklahoma 110 ft at 90,000 lb, from Nebraska 65 ft loaded or 95 ft empty at 95,000 lb. Pick the entry state in the checker, or the Missouri result reads as a check rather than a verdict.

The Rocky Mountain double is also the configuration most often confused with a turnpike double. The difference is the rear trailer: a pup makes it a Rocky Mountain double, while a second long trailer makes it a turnpike double. Some states treat them identically, but several do not. Indiana, Ohio, plus New York set their longest doubles limits for two long trailers, while Oregon plus Washington cap both forms at the same short 68 ft. Pick the configuration that matches the rig actually coupled, not the one with the friendlier limit.

What is a turnpike double?

A turnpike double is a tractor plus two long trailers, typically 40 to 48 ft each. The name comes from the toll roads where the combination grew up: the turnpikes were built wide plus straight enough for two long trailers, while ordinary highways were not. A standard turnpike double with two 48 ft trailers measures 100 ft of cargo, which fits the longest doubles states but fails in most of the West. The turnpike double is the heaviest two-trailer combination on the road, reaching 143,000 lb on the New York Thruway with 9 axles plus 164,000 lb in Michigan on 11 axles.

The turnpike double states form an eastern plus midwestern band. New York allows 102 ft of cargo on the Thruway at 143,000 lb for 9 axles plus 138,400 lb for 8 axles, with a 127,000 lb figure for B-trains. Massachusetts allows 104 ft at 127,400 lb on the Turnpike, with a 92 ft minimum axle spacing for the top weight plus a tunnel ban. Indiana sets its weight by formula: 90,000 lb plus 1,070 lb for each foot of overall length over 60 ft, capped at 127,400 lb, which means a rig needs about 95 ft overall before the formula reaches the cap. Ohio sets weight bands by overall length: 90,000 lb at 90 ft overall or less, 127,400 lb from over 90 ft to under 112 ft, with a minimum cargo length of 80 ft. South Dakota allows 100 ft at 129,000 lb. Kansas allows 109 ft at 120,000 lb on the Turnpike. Oklahoma allows 110 ft at 90,000 lb. Colorado allows 111 ft at 110,000 lb.

Florida runs a turnpike double program that the checker treats with care. Appendix C allows Florida doubles of 106 ft of cargo on the Turnpike, but it sets no maximum weight for them, so the checker returns a check result rather than a legal verdict for any Florida turnpike double over 80,000 lb. The weight limit must come from the Florida Turnpike Authority. A Florida turnpike double at 80,000 lb or less reads as legal, because the length fits plus no weight rule is broken.

Turnpike doubles are usually restricted to the named toll road plus short access segments. The New York Thruway, the Massachusetts Turnpike, the Indiana Toll Road, the Ohio Turnpike, the Kansas Turnpike, the Pennsylvania Turnpike, plus the Florida Turnpike each carry their own permit plus access rules. A turnpike double that leaves its toll road for an ordinary Interstate is outside its authorization. The checker names the routes for each state in the per-state table. The State Legal Limits Table lists the standard length plus weight limits for every state alongside the LCV figures here.

One more turnpike double caution: overall length limits bind on some routes even when the cargo fits. Ohio turnpike doubles must stay under 112 ft overall. Indiana has no separate overall cap, but the weight formula turns on overall length, so a shorter rig gets a lower weight cap. Montana allows 110 ft overall for a conventional tractor plus a 95 ft plus 105 ft split for a cabover. Enter a measured overall length when the rig is close to any of these figures.

Are STAA twin 28s legal in all 50 states?

Yes. STAA twin 28s are legal on the National Network in all 50 states at 80,000 lb or less. The Surface Transportation Assistance Act of 1982, plus the federal size rules that followed it, set twin trailers of 28.5 ft each as a national standard that no state may refuse on the National Network. The 1991 freeze does not touch STAA twins, because the freeze covers longer combination vehicles, which the statute defines as combinations over 80,000 lb on the Interstate. A pair of 28.5 ft trailers at 80,000 lb or less is outside that definition entirely.

The distinction matters at the state line. A triples rig crossing from Utah into Colorado stays legal, because both states allow triples. The same rig crossing from Colorado into Kansas stays legal on the Turnpike. But a triples rig crossing from Kansas into Missouri needs the Kansas entry variant. A triples rig crossing from Missouri into Illinois must break down, because Illinois has no LCV authorization at all. The fallback everywhere is the same: break the combination down to STAA twin 28s at 80,000 lb or less, which run on the National Network in every state. The checker says this in its reason text whenever a configuration cannot run in a checked state.

STAA twins over 80,000 lb are a different question. The answer turns on state grandfathered weight. New York allows STAA twins to 100,000 lb. New Mexico allows 86,400 lb. Pennsylvania allows 100,000 lb on the Turnpike system. Michigan allows 164,000 lb under its axle-based system. In the LCV states, STAA twins over 80,000 lb use the state doubles cap: 129,000 lb in Nevada, Utah, plus South Dakota, 131,060 lb in Montana, 105,500 lb in Idaho, Oregon, Washington, plus North Dakota. In a state with no grandfathered weight exception, the cap stays at 80,000 lb. An STAA twin over that weight is not legal there. The checker applies each state cap in its STAA mode.

The STAA twin standard also sets the floor for the tool length checks. A trailer over 28.5 ft is not an STAA twin, so the checker refuses an STAA check with a longer trailer plus points to the Rocky Mountain double or turnpike double configuration instead. The 28.5 ft figure is the federal standard trailer length for twins: the original STAA figure was 28 ft, raised to 28.5 ft by ISTEA in 1991. Trailers built to the older 28 ft standard still run as STAA twins everywhere.

One boundary deserves emphasis: STAA twin legality applies on the National Network, which covers the Interstate System plus designated federal-aid highways. Off the Network, state plus local rules govern. A twin combination legal on the Interstate may be restricted on a state highway or a city street. Terminal access is part of the federal scheme: reasonable access to terminals, plus to food, fuel, rest, plus repair, is protected. The Kingpin Law Checker covers the state kingpin-to-rear-axle limits that can restrict a twin combination on state routes even when the federal length is legal.

What weight can each LCV state allow?

The full table below lists all 27 Appendix C states with their doubles plus triples limits, read from the appendix on November 19, 2026. Cargo length is in feet, gross weight in pounds. A dash means the state has no authorization for that configuration. Where a state sets its limit by formula, by axle count, or by the state of entry, the table shows the headline figure plus a note naming the rule. The checker applies the full rule for each state, not the headline alone.

StateDoubles cargoDoubles weightTriples cargoTriples weightNote
Alaska95 ftNo Interstate cap110 ftNo Interstate capTriples May 1 to Sep 30
Arizona95 ft129,000 lb95 ft123,000 lbTriples 129,000 lb on I-15
Colorado111 ft110,000 lb115.5 ft110,000 lbRush-hour bans in three cities
Florida106 ftNo cap stated––Turnpike only, weight unlisted
Hawaii65 ft80,000 lb––Not an LCV above 80,000 lb
Idaho95 ft105,500 lb95 ft105,500 lbAll NN routes, annual permit
Indiana106 ft127,400 lb104.5 ft127,400 lbDoubles weight by formula
Iowa100 ft129,000 lb100 ft129,000 lbSioux City zone, entry-dependent
Kansas109 ft120,000 lb109 ft120,000 lbTurnpike plus SVC corridor
Massachusetts104 ft127,400 lb––Turnpike only, tunnel ban
Michigan58 ft span164,000 lb––Axle-based, no limit at twin 28.5s
Mississippi65 ft80,000 lb––Each trailer 30 ft or less
Missouri110 ft120,000 lb109 ft120,000 lbEntry-dependent, see text
Montana93 ft131,060 lb100 ft131,060 lbB-train 137,800 lb on I-15
Nebraska95 ft95,000 lb95 ft80,000 lbEmpty only over 65 ft cargo
Nevada95 ft129,000 lb95 ft129,000 lbCab-card LCV authority
New MexicoSTAA twins86,400 lb––STAA twins only
New York102 ft143,000 lb––9 axles; 8 axles 138,400 lb
North Dakota100 ft105,500 lb100 ft105,500 lbSingle-trip permit over 80,000 lb
Ohio102 ft127,400 lb95 ft115,000 lbDoubles weight by overall band
Oklahoma110 ft90,000 lb95 ft90,000 lbEach triples trailer 29 ft or less
Oregon68 ft105,500 lb96 ft105,500 lb105 ft overall limit binds
Pennsylvania57 ft total100,000 lb––STAA twins only, Turnpike system
South Dakota100 ft129,000 lb100 ft129,000 lbPer-trailer limits by cargo length
Utah95 ft129,000 lb95 ft129,000 lbInterstates plus freeways only
Washington68 ft105,500 lb––Annual overlength permit over 60 ft
Wyoming81 ft117,000 lb––81 ft includes the coupling

Three figures in the table need a longer note than the table allows. Arizona triples carry an internal inconsistency inside Appendix C itself: the summary table says 129,000 lb, the narrative headline says 123,000 lb with 129,000 lb on I-15, plus one paragraph of the narrative says 123,500 lb. The checker uses 123,000 lb as the general triples cap plus 129,000 lb on I-15, which follows the narrative headline. It flags the 123,500 lb figure as unresolved. Until the appendix is corrected, a triples rig between 123,000 lb plus 123,500 lb in Arizona should confirm the limit with the state DOT before rolling.

Missouri plus Iowa are the two entry-dependent states. Their headline figures in the table are the most generous variant, not a single limit. Missouri doubles run 109 ft at 120,000 lb from Kansas, 110 ft at 90,000 lb from Oklahoma, plus 65 ft loaded or 95 ft empty at 95,000 lb from Nebraska. Missouri triples run 109 ft at 120,000 lb from Kansas plus 95 ft at 90,000 lb from Oklahoma. Iowa doubles plus triples run 100 ft at 129,000 lb from South Dakota plus 65 ft at 95,000 lb from Nebraska, in the Sioux City zone only. The checker applies the variant for the entry state picked, or returns a check result when no entry state is picked.

The highest weights in the table come with their own conditions. Michigan 164,000 lb is axle-based: the gross weight is determined by the state axle plus axle group limits, with 11 axles maximum, 18,000 lb per single axle, plus a 400 to 1 weight-to-horsepower ratio. New York 143,000 lb needs 9 axles; an 8-axle rig is capped at 138,400 lb, plus a rig with fewer axles gets no Appendix C figure at all, so the checker returns a check result. Montana 131,060 lb is the highest flat triples cap in the country, with a B-train memorandum figure of 137,800 lb on I-15 between Canada plus Shelby. Indiana 127,400 lb is a formula ceiling, reached only at about 95 ft of overall length.

Below the state cap, two more rules always apply. The federal bridge formula caps gross weight by axle count plus axle spacing. The state axle limits cap each axle plus each axle group. A rig at a state maximum still fails when its axles are too close together or too heavily loaded. The Superload Threshold Checker covers the point where a load crosses from a routine overweight permit into superload territory, which matters for the heaviest LCV states. The Weight Distance Tax Checker covers the per-mile taxes that Oregon, New Mexico, New York, plus Kentucky charge by weight plus distance.

What routes can LCVs use?

An LCV may run only on the routes its state lists in Appendix C, plus reasonable access to terminals, food, fuel, rest, plus repair. The route lists vary from the whole National Network to a single toll road. Idaho allows LCVs on all National Network routes. Nevada allows all National Network routes except US 93 from Nevada State Route 500 to Arizona. Utah allows Interstates plus freeways only, under R909-2 effective March 16, 2026, with LCV authority required for any tractor plus two or three trailers over 81 ft of cargo, up to four routes per authority, plus a maximum of one traveled mile off or onto the listed route. Oregon restricts LCVs to designated routes published by the state DOT. The checker names the routes for each state in the per-state table, but the route list is the part of LCV law that changes most often, so confirm it with the state DOT before the trip.

The turnpike states restrict LCVs to their toll roads plus short connectors. New York LCVs run the Thruway: I-87, I-90, I-190, plus the Berkshire Spur. Massachusetts LCVs run the Turnpike from the New York line to Exit 18 in Boston, with a tunnel ban that keeps them out of the Boston tunnels. Indiana LCVs run the Toll Road plus the I-80 plus I-90 segments the program lists. Ohio LCVs run the Turnpike plus the one-mile SR 7 segment south of exit 16 for triples. Kansas LCVs run the Turnpike plus the SVC triples corridor on I-70 from the Colorado line to Goodland. Pennsylvania LCVs run the Turnpike system only. Florida turnpike doubles run the Turnpike only. A turnpike double that leaves its toll road for an ordinary Interstate is outside its authorization, even when the weight plus length fit.

Access rules decide the last mile. Most states allow reasonable access from the listed route to a terminal, plus to food, fuel, rest, plus repair. Some states set a hard number: Utah allows one traveled mile. Nebraska limits access to designated staging areas within six miles of I-80 between the Wyoming line plus Exit 440. A Nebraska LCV that exits I-80 may not reenter it except for weather, emergency, or repair. Alaska allows LCVs on the listed routes plus terminal access within the commercial zones. The checker names the access rule where Appendix C states one. Where it does not, the state DOT or permit office is the authority.

Time-of-day plus weather restrictions sit on top of the route lists. Colorado bans LCVs during rush hours in Denver, Colorado Springs, plus Pueblo. Nebraska bans length-permit movement on Saturdays, Sundays, plus holidays, when ground wind speed exceeds 25 miles per hour, when visibility falls under 800 ft, or when steady rain, snow, sleet, ice, or other conditions cause slippery pavement. North Dakota requires a LONG LOAD sign on the rear of a long combination. The Oversize Curfew Holiday Checker covers the curfew plus holiday rules that apply to overlength loads state by state. The Oversize Sign Flag Checker covers the signs, flags, plus lights an overlength combination must carry. The Escort Pilot Car Checker covers the escort rules that apply when a load crosses into oversize territory.

States may restrict LCV routes further without changing Appendix C, which is the most important route fact on this page. The appendix records the frozen maximum: what the state allowed on June 1, 1991. A state DOT may close a route, shorten a corridor, or add a restriction at any time. The appendix does not update to match. The checker reads the appendix plus current state DOT sources at each review, but a route closure issued last week will not appear here. Confirm every route with the state DOT or permit office before the rig rolls.

What permit does each state require?

Permit requirements run from none to an annual program permit. The checker names the permit for each state in the per-state table. Five states require no permit for the LCV itself: Alaska, Hawaii, Mississippi, New Mexico, plus Wyoming. In those states the combination runs on its registration plus the driver credentials, though an overweight permit may still apply for the weight. Washington requires an annual overlength permit when the cargo exceeds 60 ft. Idaho requires an annual permit. North Dakota requires a single-trip permit over 80,000 lb. Nebraska requires a weight permit over 80,000 lb plus a length permit over 65 ft of cargo, with the length permit carrying weekend, holiday, wind, plus visibility conditions.

Nevada runs LCV authority through the cab card. Under AB320, the LCV weight declaration on the cab card (80,001 lb to 129,000 lb) carries the authority. No other permit is required for the weight. NAC 706.156, revised in October 2026, still provides a 12-month LCV permit as the program document. A Nevada LCV driver should carry both the cab card showing the declared weight plus the permit, because an inspector may ask for either. The checker states the cab-card route plus the 12-month permit together, so neither document is missed.

Indiana runs a formal LCV program through the state DOT, with driver permits plus tractor permits issued under the LCV manual M-233T for 2026 to 2027. Manual tractor permits stopped being accepted on July 1, 2026, plus manual driver permits on August 1, 2026: both now run through the online system. New York requires a Tandem Trailer Permit from the Thruway Authority at no fee, plus a Thruway Authority driver permit, plus a DOT overweight permit on I-84 plus I-287. Ohio requires a Turnpike permit. Massachusetts requires a Turnpike permit. The Trip Permit Checker covers the temporary registration plus fuel permits a carrier needs when entering a state without full IRP plus IFTA credentials.

Permit fees change, so this checker does not print fee figures. A fee printed here would be stale within a year, plus a stale fee is worse than no fee, because a driver who budgets on it arrives short. The permit office for each state publishes the current fee schedule. What the checker does print is the permit type, the issuing office, plus the conditions that matter for planning: annual versus single-trip, weekend bans, wind limits, plus the documents to carry. Check the fee with the issuing office when the permit is ordered.

One permit fact surprises new LCV operators: the permit follows the combination, not the tractor alone. A tractor permitted for LCV operation in Idaho cannot pull a triples combination in Oregon on the Idaho permit. Each state issues its own authority for its own roads. The driver carries the permits for every state on the route. The checker action list names every state on the route where a permit is required, so the permit packet can be assembled before the trip starts.

What license and training does an LCV driver need?

An LCV driver needs two credentials beyond the Class A CDL: the T endorsement plus the LCV driver-training certificate. The T endorsement, formally the Double or Triple Trailers endorsement, is a knowledge test only under 49 CFR 383.93(b)(1) plus (c)(1). No skills test is required for the endorsement itself. The driver studies the doubles plus triples material, passes the written test at the licensing office, plus the T endorsement is added to the CDL. The CDL Endorsement Checker lists every CDL endorsement plus what each one requires. The CDL Class Checker works out which CDL class a combination needs.

The training certificate is the heavier requirement. Under 49 CFR Part 380 Subpart B, a driver must complete an LCV driver-training program before operating a longer combination vehicle. Section 380.107 sets the training standard by reference to Appendix F of Part 380, plus requires a certificate on completion. Section 380.109 sets the pass standard: 80 percent on the knowledge test, a skills test covering all maneuvers, with an automatic fail for a traffic law violation or a preventable crash during the test. Section 380.113 bars a carrier from allowing a driver without the certificate to operate an LCV. Sections 380.203 plus 380.205 set the preconditions: six months of qualifying experience, including a Class A CDL with the double or triple endorsement.

The grandfathering window is closed. This is the most common misunderstanding in LCV licensing. Section 380.111(e) allowed grandfathering only during the year following June 1, 2004. A driver who qualified under that window kept the credential. A driver who did not qualify by June 1, 2005 cannot grandfather in now: training is the only route. Any advice that an experienced doubles driver can skip LCV training on the strength of years behind the wheel is out of date by twenty years. The LCV Training Requirement Checker tests any driver against the Part 380 rules plus states exactly which training applies.

Several states add their own driver conditions on top of the federal rules. Nevada requires the LCV driver to be 25 or older, plus sets a 500 ft following distance for LCVs. New York requires a Thruway Authority driver permit, with a minimum age of 26 plus five years of experience, plus annual equipment certification. Nebraska requires the driver of a combination over 65 ft of cargo to meet all state plus federal requirements, plus to have had no accidents while operating such vehicles. Alaska requires 10 years of Alaska driving experience for triples. The checker names the state driver condition in the per-state note where Appendix C states one.

The carrier holds duties too. Under section 380.113, a motor carrier must not allow a driver to operate an LCV without the training certificate, plus must keep the training records. A carrier that dispatches an uncertified driver to pull triples faces the same violation as the driver, plus a negligent entrustment exposure if the combination is involved in a crash. Check the certificate before dispatch, not after the inspection. The FMCSA Fine Calculator works out the current inflation-adjusted penalty for a given FMCSA violation.

How does the bridge formula limit LCV weight?

The federal bridge formula, Formula B, caps gross weight by the number of axles plus the distance between the first plus the last axle of any group. The formula is W equals 500 times the bracket L times N divided by N minus 1, plus 12 times N, plus 36, where W is the gross weight in pounds, L is the distance in feet between the first plus the last axle of the group, plus N is the number of axles in the group. The formula exists to protect bridges: it spreads the load over length, so a heavy rig needs its axles spread out. A short heavy rig fails the formula even when its gross weight fits the state maximum.

The bridge formula is the rule that most often cuts an LCV weight below the state cap. Take a 9-axle triples rig at the Montana maximum of 131,060 lb. On a 100 ft axle spread, the formula allows about 131,500 lb, so the rig passes. On an 85 ft spread, the formula allows about 122,000 lb, so the same rig at the same gross weight fails by 9,000 lb. The state cap is a ceiling, not a promise: the formula decides what the axles as spaced can actually carry. Shorten the spread by coupling the trailers closer, or shift weight forward, plus the formula result changes.

The axle limits sit beside the formula. On the Interstate, no single axle may exceed 20,000 lb plus no tandem axle group may exceed 34,000 lb, under 23 USC 127(a). Some states set lower axle limits for LCVs: Michigan caps single axles at 18,000 lb for axles spaced 9 ft or more apart, plus 13,000 lb for axles spaced between 3.5 ft plus 9 ft apart, with tandem limits of 16,000 lb per axle for the first tandem plus 13,000 lb per axle for later tandems. Seasonal load reductions cut these figures further at thaw: 25 percent on rigid pavements plus 35 percent on flexible pavements in Michigan. Scale the axles, then test the formula, then compare against the state cap. All three must pass.

The checker does not test axle weights or the bridge formula, because it does not ask for axle spacing plus axle loads. That is a deliberate scope limit, not an omission: axle data belongs on the scale ticket, not in a route checker. After this checker confirms the route, the Bridge Formula Axle Weight Checker tests the axle figures from the scale ticket against Formula B plus the federal axle limits. Run the route check first, then the axle check, then confirm the permits. A rig that passes all three is ready to roll.

How do you use the LCV Route Checker?

Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the verdict change.

  1. Pick the configuration: STAA twins, triples, Rocky Mountain double, or turnpike double.
  2. Enter each trailer length in feet, plus the tractor length.
  3. Enter the gross weight in pounds, the axle count, plus loaded or empty.
  4. Pick every state on the route. Add the entry state for Missouri or Iowa.
  5. Read the verdict plus the per-state table for routes, weights, plus permits.
  6. Measure the rig when the estimate sits near a limit, then confirm with each state DOT.

Use measurements from the rig, not from a brochure. A manufacturer specification sheet gives the design figures, which may differ from the combination as coupled plus as worn. A dolly changed since the last trip changes the coupling gap. A tractor swapped for a cabover changes the overall length by several feet. The checker is only as good as the tape measure behind it.

Read the figures table before the action list. It shows the configuration, the trailer lengths, the cargo length plus the overall length with each marked estimated or measured, the gross weight, the axle count, the lowest weight cap on the route, plus the states checked, so you can see which figure is closest to failing even when the combination passes. A rig that passes with a weight margin of zero will fail the next time the load shifts. The figures table is where that risk shows.

Questions drivers ask

Which states allow triples?

Seventeen states allow triples: Alaska, Arizona, Colorado, Idaho, Indiana, Iowa, Kansas, Missouri, Montana, Nebraska, Nevada, North Dakota, Ohio, Oklahoma, Oregon, South Dakota, plus Utah. Nebraska triples must travel empty. Iowa triples run only in the Sioux City zone. Missouri triples depend on the state of entry. The list is fixed by the 1991 freeze in 23 USC 127(d): no state can join it.

Can triples run in Texas?

No. Texas has no LCV authorization in 23 CFR Part 658 Appendix C, so triples cannot run there at any weight. The same applies to California, Illinois, plus every southeastern state. A triples rig heading into Texas must break down to STAA twin 28s at 80,000 lb or less before the state line.

Do I need a special endorsement to pull triples?

Yes, two credentials: the T endorsement for double or triple trailers on the CDL, plus the LCV driver-training certificate under 49 CFR Part 380 Subpart B. The endorsement needs a knowledge test only. The training needs a Part 380 program plus a certificate, because the grandfathering window closed in 2005.

What is the maximum weight for triples?

It depends on the state. Montana allows 131,060 lb, the highest flat triples cap. South Dakota, Nevada, Utah, plus Iowa from South Dakota allow 129,000 lb. Idaho, Oregon, plus North Dakota allow 105,500 lb. Arizona allows 123,000 lb generally plus 129,000 lb on I-15. Nebraska triples are capped at 80,000 lb, empty only. The bridge formula plus the axle limits apply below every state cap.

Are twin 28s legal in every state?

Yes, at 80,000 lb or less on the National Network. STAA twin 28.5 ft trailers are a federal standard that no state may refuse on the Network, plus the 1991 freeze does not touch them. Over 80,000 lb, STAA twins need a state grandfathered weight exception: 100,000 lb in New York plus Pennsylvania, 86,400 lb in New Mexico, 164,000 lb in Michigan.

Why can no new state allow triples?

Congress froze LCV operations in the ISTEA law of 1991, written into 23 USC 127(d). An LCV configuration may operate only where state law authorized it plus it was in actual lawful operation on or before June 1, 1991. A state that misses that test cannot add triples, raise a weight cap, or open a new LCV route. States can only restrict further.

Related tools

Sources

Follow on WhatsApp Ask by Voice