One rig at a time. This checker runs one set of rig dimensions against the legal size and weight limits in all 50 states plus the District of Columbia. Legal height is not a clearance guarantee. Check bridges, signs and wires on the route before you roll.
Enter the rig dimensions. Every answer updates as you change each field.
Your rig
Measure height from the ground to the highest point of the load, not to the top of the trailer. Leave overall length blank to skip that check. Only ten states set an overall combination limit, so the check is blank for the rest.
Weights
The federal baseline is 80,000 lb gross, 20,000 lb on a single axle and 34,000 lb on a tandem. Leave the axle fields blank to skip the axle checks. The bridge formula can still cap a legal-looking gross weight on short axle spacings.
Route and states
Route type matters in Louisiana and Missouri. Both allow 14 ft on the Interstate and 13 ft 6 in on other roads. Pick one state for a full check table, or all states for the 51-row verdict table.
Legal in 50 of 51 jurisdictions
Legal in 50 of 51 jurisdictions; over the limit in 1.
| State | Verdict | Over on |
|---|---|---|
| Alabama | Legal | Fits every limit checked. |
| Alaska | Legal | Fits every limit checked. |
| Alaska: 48 ft general; 53 ft on designated highways with kingpin to center of rear group 41 ft or less. | ||
| Arizona | Legal | Fits every limit checked. |
| Arkansas | Legal | Fits every limit checked. |
| California | Legal | Fits every limit checked. |
| California: 53 ft with 40 ft kingpin to rearmost axle (38 ft single axle). | ||
| Colorado | Legal | Fits every limit checked. |
| Connecticut | Legal | Fits every limit checked. |
| Delaware | Legal | Fits every limit checked. |
| District of Columbia | Legal | Fits every limit checked. |
| Florida | Legal | Fits every limit checked. |
| Florida: 48 ft standard; 49 to 57 ft with kingpin conditions (316.515(3)(b)2). | ||
| Georgia | Legal | Fits every limit checked. |
| Hawaii | Over | Semitrailer |
| Hawaii: 48 ft semitrailer; 65 ft overall (HRS 291-34(c)). | ||
| Idaho | Legal | Fits every limit checked. |
| Illinois | Legal | Fits every limit checked. |
| Indiana | Legal | Fits every limit checked. |
| Iowa | Legal | Fits every limit checked. |
| Kansas | Legal | Fits every limit checked. |
| Kentucky | Legal | Fits every limit checked. |
| Louisiana | Legal | Fits every limit checked. |
| Maine | Legal | Fits every limit checked. |
| Maryland | Legal | Fits every limit checked. |
| Massachusetts | Legal | Fits every limit checked. |
| Michigan | Legal | Fits every limit checked. |
| Minnesota | Legal | Fits every limit checked. |
| Mississippi | Legal | Fits every limit checked. |
| Missouri | Legal | Fits every limit checked. |
| Montana | Legal | Fits every limit checked. |
| Nebraska | Legal | Fits every limit checked. |
| Nebraska: Owners assume the risk of striking structures above 12 ft 6 in. | ||
| Nevada | Legal | Fits every limit checked. |
| New Hampshire | Legal | Fits every limit checked. |
| New Jersey | Legal | Fits every limit checked. |
| New Mexico | Legal | Fits every limit checked. |
| New York | Legal | Fits every limit checked. |
| New York: 53 ft on qualifying and access highways (kingpin to rear axle 43 ft or less); 65 ft combination on other highways. | ||
| North Carolina | Legal | Fits every limit checked. |
| North Carolina: Owner liable for damage to any structure above 12 ft 6 in (G.S. 20-116(c)). | ||
| North Dakota | Legal | Fits every limit checked. |
| Ohio | Legal | Fits every limit checked. |
| Oklahoma | Legal | Fits every limit checked. |
| Oregon | Legal | Fits every limit checked. |
| Pennsylvania | Legal | Fits every limit checked. |
| Rhode Island | Legal | Fits every limit checked. |
| South Carolina | Legal | Fits every limit checked. |
| South Dakota | Legal | Fits every limit checked. |
| Tennessee | Legal | Fits every limit checked. |
| Texas | Legal | Fits every limit checked. |
| Utah | Legal | Fits every limit checked. |
| Vermont | Legal | Fits every limit checked. |
| Virginia | Legal | Fits every limit checked. |
| Washington | Legal | Fits every limit checked. |
| West Virginia | Legal | Fits every limit checked. |
| Wisconsin | Legal | Fits every limit checked. |
| Wyoming | Legal | Fits every limit checked. |
Notes
Alaska has no Interstate weight limits. Gross and axle weights there follow the Alaska state formula in 17 AAC 25.013, so this checker does not score weights for Alaska.
Legal height is not a clearance guarantee. Check bridges, signs and wires on the route; cities and counties post lower clearances.
Disclaimer: This tool is provided for general information only. It is not legal advice โ check the current state statute and your company policy before you rely on a result.
Quick answer: The most common legal truck height is 13 ft 6 in, in 26 states plus the District of Columbia. Nineteen states allow 14 ft, Colorado and Nebraska allow 14 ft 6 in and Alaska allows 15 ft. Louisiana and Missouri allow 14 ft on the Interstate and 13 ft 6 in on other roads. There is no federal height limit. Width is 102 in everywhere except Hawaii at 108 in. Gross weight is 80,000 lb everywhere except the grandfathered states, where Michigan reaches 164,000 lb on the Interstate.
What is the legal truck height in each state?
There is no federal truck height limit. The Federal Highway Administration sets no national maximum height, so each state sets its own. That is why a rig that is legal in Texas at 14 ft can be over height the moment it crosses into Oklahoma at 13 ft 6 in on a county road. The table below shows the split across all 50 states plus the District of Columbia, as verified from the state rules on November 19, 2026.
| Legal height | How many | States |
|---|---|---|
| 13 ft 6 in | 27 | 26 states plus the District of Columbia, including New York, Pennsylvania, Ohio, Illinois, Georgia, Florida and Michigan |
| 14 ft on the Interstate, 13 ft 6 in elsewhere | 2 | Louisiana and Missouri |
| 14 ft | 19 | Arkansas, Arizona, California, Hawaii, Idaho, Kansas, Maine with load, Montana, North Carolina, North Dakota, Nevada, New Mexico, Oklahoma, Oregon, South Dakota, Texas, Utah, Washington and Wyoming |
| 14 ft 6 in | 2 | Colorado and Nebraska |
| 15 ft | 1 | Alaska |
Two states change height with the road. Louisiana allows 14 ft only when the vehicle runs exclusively on the Interstate, under La. R.S. 32:381(A)(1). Missouri allows 14 ft on the Interstate and on designated highways and 13 ft 6 in on other highways, under RSMo 304.170.2. The checker asks for the route type for exactly this reason. Pick the wrong route type and a legal load looks over height, or worse, an over-height load looks legal.
Maine is the trickiest case in the table. The statute caps the vehicle structure at 13 ft 6 in and lets the load rise 6 in higher, so a loaded rig can reach 14 ft. The Maine Turnpike caps the whole vehicle at 13 ft 6 in. A 14 ft load is legal on Interstate 95 north of the turnpike and illegal on the turnpike itself. The checker scores Maine at 14 ft and the reference table carries the turnpike note.
Heights change. Old tables go stale. Arkansas raised its limit from 13 ft 6 in to 14 ft in 2021 under Act 871. Some Arkansas permit documents still show the old figure. North Carolina raised its limit from 13 ft 6 in to 14 ft after 2015. Older statute mirrors still show the old text. Arizona allows 14 ft under ARS 28-1094, but some published tables still list 13 ft 6 in. A few restricted routes in Arizona drop back to 13 ft 6 in under Table 4 of the state administrative code. Every height in this table was re-checked against the state rule at build time. The source for each state is listed in the sources section below.
How wide can a truck be without a permit?
The federal width limit is 102 in, or 8 ft 6 in, under 23 CFR 658.15. Every state except Hawaii uses that figure. Hawaii allows 108 in, or 9 ft. A 102 in wide trailer is legal in all 50 states plus the District of Columbia on width alone. A trailer wider than 102 in needs a permit everywhere except Hawaii, where the line sits at 108 in.
Width is measured across the widest part of the vehicle or load, not across the mirrors. Section 658.16 excludes safety devices and other non-property-carrying devices from the width measurement. Mirrors, turn signals, splash guards and similar fittings do not count toward the 102 in. A load that overhangs the side of the trailer does count. The load width, not the trailer width, decides the check.
Width rarely causes a surprise on its own. Standard dry vans, reefers and flatbeds all run at 102 in. The width check matters most for wide loads: construction equipment, manufactured housing components and machinery on a step deck. A load that measures 104 in is over width in 50 jurisdictions and legal in one. The permit rules change with it. The checker flags the width verdict first, before height and length, because a width failure usually means a different trailer or a permit, not a different route.
How long can a semitrailer be in each state?
Federal law sets a floor, not a ceiling, for semitrailer length. Section 658.13 bars any state from setting a semitrailer limit below 48 ft on the National Network. Most states go well past the floor. Forty-five states allow a 53 ft semitrailer, which is why 53 ft is the standard trailer length in the United States. The exceptions matter more than the rule.
Florida sets 48 ft as the standard semitrailer length and allows 49 ft to 57 ft only when the kingpin-to-rear-axle distance meets the conditions in Fla. Stat. 316.515(3)(b)2. A 53 ft trailer in Florida is legal only when the kingpin setting is right. Hawaii caps the semitrailer at 48 ft with no longer option. Hawaii also caps the overall combination at 65 ft. Texas allows a 59 ft semitrailer. Kansas allows 59 ft 6 in. Oklahoma allows 59 ft 6 in on the National Network. Arizona allows 57 ft 6 in. Alaska allows 48 ft generally and 53 ft on designated highways when the kingpin distance is 41 ft or less.
Length and kingpin distance work together. A long trailer with the tandems slid too far back can break the kingpin law even when the trailer length itself is legal. The Kingpin Law Checker runs the kingpin-to-rear-axle distance against the state rule, including the California 40 ft limit and the Florida conditions. Run both checks together before dispatch: this table for the trailer length, the kingpin checker for the axle position.
Overall combination length is a separate limit. Only ten states set one. Alaska caps the combination at 75 ft. California, Hawaii, Kansas, Maine, Nebraska, New York and Texas cap it at 65 ft, each with its own scope. Colorado caps it at 70 ft. Florida caps a truck-trailer combination at 68 ft. The federal rules bar states from setting an overall length limit for a tractor-semitrailer on the National Network, so most states set none at all. Enter the overall length in the checker when the load runs a truck-trailer combination or a double. Leave it blank for a standard tractor-semitrailer.
What is the maximum gross weight by state?
The federal gross weight limit is 80,000 lb under 23 CFR 658.17. That figure holds in most states on the Interstate. The single axle limit is 20,000 lb and the tandem limit is 34,000 lb. Those three numbers are the baseline for the whole table. Every state in the table starts from them. The grandfathered states add exceptions on top.
Gross weight alone does not make a load legal. The bridge formula in 23 USC 127 sets a separate limit based on the number of axles and the distance between them. A five-axle combination at 80,000 lb needs 51 ft between the first and last axle to carry the full weight. A shorter spacing caps the gross weight below 80,000 lb even when every axle is under its own limit. The Bridge Formula Axle Weight Checker runs the axle spacings against the formula. The Axle Weight Rebalance Calculator works out how far to slide the fifth wheel or the tandems when one axle group is heavy.
The grandfathered states break the 80,000 lb ceiling on specific roads. Michigan allows 164,000 lb on the Interstate and on designated state highways. Florida allows 147,000 lb on the Florida Turnpike only. Indiana allows 127,400 lb on the I-80/90 Toll Road. Maine allows 100,000 lb on all Interstate highways. New Hampshire allows 103,000 lb. New Mexico allows 86,400 lb. Hawaii allows 88,000 lb. New York allows 143,000 lb on the Thruway. The checker scores each of these as an exception, not as a pass, because the higher weight applies only on the named road and only with the axle configuration the state rule requires.
The Federal Size Limits Checker covers the federal floor that sits under all of these state rules: the 102 in width, the 48 ft semitrailer floor, the 80,000 lb gross weight and the axle limits. Use it when the question is what the federal rules allow. Use this table when the question is what one state allows, which is the stricter limit on most routes.
Why does Michigan allow 164,000 pounds but cap axles lower?
Michigan is the most misunderstood weight state in the country. The 164,000 lb figure is real: Michigan allows it on the Interstate and on designated state highways under a grandfathered right that predates the federal limits. The catch is in the axles. Michigan caps a single axle at 18,000 lb and a tandem at 32,000 lb, both lower than the federal 20,000 lb and 34,000 lb. A rig that carries 20,000 lb on a steer axle is legal everywhere else and over in Michigan.
The combination works because Michigan spreads the weight across more axles. A Michigan train runs 11 axles: a tractor with a short trailer, a dolly and a second trailer, or a straight truck with multiple lift axles. Each axle carries less than the federal limit. The total adds up to 164,000 lb. The federal axle limits still cap any single axle at 20,000 lb, so the Michigan 18,000 lb cap is the binding limit on a Michigan road. The checker applies the Michigan axle caps when Michigan is the selected state. It warns whenever a single axle passes 18,000 lb or a tandem passes 32,000 lb there.
Michigan is not the only state with axle limits that differ from the federal figures. Connecticut allows 22,400 lb on a single axle and 36,000 lb on a tandem while keeping the 80,000 lb gross weight. The District of Columbia allows 22,000 lb on a single axle and 38,000 lb on a tandem. Georgia allows 20,340 lb on a single axle. Maryland allows 22,400 lb on a single axle when the registered gross vehicle weight is under 73,000 lb. Rhode Island allows 22,400 lb on a single axle and 44,800 lb on a tandem. Vermont allows 22,400 lb on a single axle and 36,000 lb on a tandem. Each of these is a grandfathered axle exception. Each appears in the reference table below.
Which states let you run heavier on a turnpike or toll road?
Several states keep their heavy weights on one road only. The exception follows the toll road, not the state line. A rig that is legal on the turnpike is over weight the moment it leaves the turnpike for a state highway. The checker marks the state as an exception rather than a pass for exactly that reason.
Florida allows 147,000 lb on the Florida Turnpike, with a single axle cap of 22,000 lb and a tandem cap of 44,000 lb. Indiana allows 127,400 lb on the I-80/90 Toll Road, with a single axle cap of 22,400 lb and a tandem cap of 36,000 lb. Ohio allows 127,400 lb on the Ohio Turnpike and 115,000 lb on other designated routes, with a single axle cap of 21,000 lb. New York allows 143,000 lb on the Thruway. Massachusetts allows 127,400 lb on the Massachusetts Turnpike. Kansas allows 120,000 lb on the Kansas Turnpike. Missouri allows 120,000 lb in a 20-mile band along the Kansas and Oklahoma borders and 90,000 lb elsewhere on designated routes.
The western longer-combination-vehicle states run heavier on the Interstate itself, not on a toll road. Arizona allows 129,000 lb on Interstate 15. Nevada, South Dakota and Utah allow 129,000 lb. Idaho, North Dakota, Oregon and Washington allow 105,500 lb. Montana allows 131,060 lb and 137,800 lb under the Montana-Alberta memorandum of understanding. Wyoming allows 117,000 lb. Colorado allows 110,000 lb. Nebraska allows 95,000 lb. These are grandfathered longer combination vehicle rights under 23 CFR Part 658 Appendix C. They apply to doubles and triples with the axle counts the state rule sets.
Turnpike weights never travel. A Florida Turnpike permit does not cover the last ten miles on a state road to the delivery dock. Plan the exit: the heavy leg ends where the turnpike ends. The final miles run at the state limit unless a separate permit covers them.
What are grandfathered truck weight exceptions?
Grandfathered weight exceptions are state weight limits that predate the federal limits and survived them. The federal weight limits in 23 USC 127 set 80,000 lb gross, 20,000 lb on a single axle and 34,000 lb on a tandem. States that allowed heavier weights on the dates Congress set, in 1956 for the Interstate system and in 1974 for the current axle limits, kept the right to allow those weights on the Interstate. The Federal Highway Administration lists them in the Compilation of Existing State Truck Size and Weight Limit Laws, Appendix B.
Some exceptions raise the gross weight. Michigan at 164,000 lb, Florida at 147,000 lb on the Turnpike, Indiana at 127,400 lb on the Toll Road, Maine at 100,000 lb on the Interstate, New Hampshire at 103,000 lb, Hawaii at 88,000 lb and New Mexico at 86,400 lb all sit above the 80,000 lb federal ceiling. Others raise only an axle limit while the gross weight stays at 80,000 lb. Connecticut, Vermont and New Jersey allow 22,400 lb on a single axle. Rhode Island allows 44,800 lb on a tandem. North Carolina allows 38,000 lb on a tandem. South Carolina allows 35,200 lb on a tandem. Georgia allows 20,340 lb on a single axle.
Grandfathered rights are narrow. They apply to the roads the state rule names, to the vehicle configurations the state rule names and to the axle counts the state rule names. A grandfathered gross weight does not waive the bridge formula. It does not waive the axle limits. Michigan proves the point in the other direction: the highest gross weight in the country sits next to the lowest axle caps in the country. The checker scores every grandfathered weight as an exception. The reference table names the road for each one.
How do you check a rig against state limits before dispatch?
Start with the rig, not the route. Measure the height from the ground to the highest point of the load. Measure the width across the widest part of the load. Read the semitrailer length from the trailer plate. Weigh the rig or read the scale ticket for the gross weight and the heaviest axle groups. Guessing any of these numbers makes the check worthless.
Enter the numbers in the checker and pick the route type. Interstate and designated highways is the default. It is the right pick for most long-haul runs. Pick other roads when the route leaves the Interstate for state highways or county roads, because Louisiana and Missouri drop to 13 ft 6 in off the Interstate and Oklahoma drops to 13 ft 6 in on county roads. Pick one state for a full seven-row check table, or all states for the 51-row verdict table.
A worked example shows the pattern. A standard rig at 102 in wide, 13 ft 6 in high, with a 53 ft semitrailer and 80,000 lb gross weight is legal in 50 of the 51 jurisdictions. The one exception is Hawaii, where the semitrailer limit is 48 ft and the 53 ft trailer is over by 5 ft. The same rig at 14 ft high is legal in 23 jurisdictions on the Interstate and over in 28, because 13 ft 6 in is still the limit in most states. The same rig at 14 ft 6 in is legal in three jurisdictions only: Colorado, Nebraska and Alaska.
A second example shows the weight side. A Michigan train at 120,000 lb gross weight, with 18,000 lb on the heaviest single axle and 32,000 lb on the heaviest tandem, is legal in Michigan under the grandfathered exception. The same train with 20,000 lb on a single axle and 34,000 lb on a tandem is over in Michigan, because the Michigan axle caps sit below the federal figures. The gross weight passes and the axles fail. That is why the checker scores axles separately from gross weight.
What happens if a load is over the legal limit in one state?
An over-limit load is not a dead end. It is a permit load. Every state issues oversize and overweight permits for loads that exceed the legal limits. Most states issue them online for a single trip or for a set period. The permit names the route, the dates and the conditions. A load that runs outside the permit conditions runs without a permit. Divisible loads, like bulk grain or palletized freight, generally cannot get an overweight permit: the load must be split to the legal weight. Non-divisible loads, like a single piece of machinery, can.
Permit rules change at every state line. A permit from one state covers that state only. A five-state run needs five permits, each with its own route, its own hours and its own escort rules. Some states ban weekend travel for oversize loads. Some ban night travel. Some require escort vehicles above a set width or length. The Escort and Pilot Car Checker works out when an escort vehicle is required and how many the state wants. The Oversize Permit Cost Calculator estimates the permit fees for a multi-state run.
Running over without a permit costs more than the permit. Fines scale with the overweight amount. An overweight stop can mean offloading at the scale until the rig is legal. An over-height strike on a bridge is worse: bridge damage, a closed road and a liability claim. The cheapest permit is the one bought before the wheels turn. Check the rig against every state on the route. Buy the permits for the states that fail and keep the permit paperwork in the cab.
Is legal height the same as bridge clearance?
No. Legal height is what the state allows on the road. Bridge clearance is what the bridge allows under it. The two numbers come from different authorities. The lower one wins. A 14 ft rig is legal in Texas and still too tall for a 13 ft 6 in bridge on a Texas farm road. The checker scores the legal limit only. It cannot know the clearance of every bridge on the route.
Several states put the clearance duty on the driver in plain words. Texas requires the driver to verify the clearance before passing under a structure above 13 ft 6 in, under Tex. Transp. Code 621.207(b). California allows 14 ft only on highways the owner deems safe for that height. North Carolina makes the owner liable for damage to a structure when the vehicle is over 12 ft 6 in. Nebraska posts lower clearances on specific routes. Cities and counties post their own clearances on local bridges. Those postings override the state limit on that road.
Use a truck routing tool that carries bridge heights. Read the signs. Posted clearance signs show the actual clearance. The posted number already includes a safety margin in most states. Never trust a clearance from memory. A repaved road sits higher than the old surface. The clearance under the bridge drops by the thickness of the new pavement. When the clearance is close, stop and measure rather than guess.
What are the truck size and weight limits in every state?
The reference table below lists the legal limits for all 50 states plus the District of Columbia, as verified on November 19, 2026. Width is in inches. Height is in feet and inches. Semitrailer and overall length are in feet. Weights are in pounds. The exception column names the grandfathered rule for the state, with the road it applies to. A dash means the state sets no limit of that kind or the federal baseline applies. Use the checker above to score a specific rig against this table.
| State | Width | Height | Semitrailer | Overall | Gross | Single | Tandem | Grandfathered exception |
|---|---|---|---|---|---|---|---|---|
| Alabama | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Alaska | 102 in | 15 ft | 53 ft | 75 ft | – | – | – | No Interstate weight limits; all weights set by the Alaska state formula (17 AAC 25.013). |
| Arizona | 102 in | 14 ft | 57.5 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 129,000 lb LCV on I-15 and listed routes (US-89, US-160, US-163). |
| Arkansas | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| California | 102 in | 14 ft | 53 ft | 65 ft | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Colorado | 102 in | 14 ft 6 in | 53 ft | 70 ft | 80,000 lb | 20,000 lb | 34,000 lb | 110,000 lb LCV on I-25, I-70, I-76, I-225, I-270; tandem 36,000 lb. |
| Connecticut | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 22,400 lb | 36,000 lb | Single 22,400 lb, tandem 36,000 lb (grandfathered). |
| Delaware | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| District of Columbia | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 22,000 lb | 38,000 lb | Single 22,000 lb, tandem 38,000 lb (grandfather right 1974). |
| Florida | 102 in | 13 ft 6 in | 57 ft | 68 ft | 80,000 lb | 20,000 lb | 34,000 lb | 147,000 lb on the Florida Turnpike only (single 22,000 lb, tandem 44,000 lb). |
| Georgia | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,340 lb | 34,000 lb | Single 20,340 lb (grandfather right 1974). |
| Hawaii | 108 in | 14 ft | 48 ft | 65 ft | 88,000 lb | 22,500 lb | 34,000 lb | 88,000 lb gross; single 22,500 lb (all NN routes except HI-95 H-1 to Barbers Point Harbor). |
| Idaho | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 105,500 lb LCV on all NN routes. |
| Illinois | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Indiana | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 127,400 lb on the I-80/90 Toll Road (single 22,400 lb, tandem 36,000 lb). |
| Iowa | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 129,000 lb LCV entering Sioux City from South Dakota; 95,000 lb from Nebraska. |
| Kansas | 102 in | 14 ft | 59.5 ft | 65 ft | 80,000 lb | 20,000 lb | 34,000 lb | 120,000 lb LCV on the Kansas Turnpike (single 22,000 lb). |
| Kentucky | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Louisiana | 102 in | 13 ft 6 in (14 ft Interstate) | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Maine | 102 in | 14 ft | 53 ft | 65 ft | 100,000 lb | 22,400 lb | 41,000 lb | 100,000 lb on all Interstate highways (single 22,400 lb, tandem 41,000 lb); limits vary by configuration. |
| Maryland | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 22,400 lb | 34,000 lb | Single 22,400 lb only if registered GVW is under 73,000 lb. |
| Massachusetts | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 127,400 lb on the Mass Pike, I-90 (single 22,400 lb, tandem 36,000 lb). |
| Michigan | 102 in | 13 ft 6 in | 53 ft | – | 164,000 lb | 18,000 lb | 32,000 lb | 164,000 lb max gross under the Michigan axle formula; single 18,000 lb, tandem 32,000 lb (all Interstate + designated state highways). |
| Minnesota | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Mississippi | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Missouri | 102 in | 13 ft 6 in (14 ft Interstate) | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 120,000 lb LCV entering from Kansas, 90,000 lb from Oklahoma (20-mile band of the KS/OK borders). |
| Montana | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 131,060 lb LCV (137,800 lb under the Montana/Alberta MOU, I-15 border to Shelby). |
| Nebraska | 102 in | 14 ft 6 in | 53 ft | 65 ft | 80,000 lb | 20,000 lb | 34,000 lb | 95,000 lb LCV (Conditional Interstate Use Permit for divisible loads). |
| Nevada | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 129,000 lb LCV on all NN routes (except US-93 from SR 500 to Arizona). |
| New Hampshire | 102 in | 13 ft 6 in | 53 ft | – | 103,000 lb | 22,400 lb | 36,000 lb | 103,000 lb gross; single 22,400 lb, tandem 36,000 lb (grandfather right 1974). |
| New Jersey | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 22,400 lb | 34,000 lb | Single 22,400 lb (grandfather right 1974). |
| New Mexico | 102 in | 14 ft | 53 ft | – | 86,400 lb | 21,600 lb | 34,200 lb | 86,400 lb gross; single 21,600 lb, tandem 34,200 lb (all Interstate highways). |
| New York | 102 in | 13 ft 6 in | 53 ft | 65 ft | 80,000 lb | 20,000 lb | 34,000 lb | 143,000 lb on the NY Thruway (I-87, I-90, I-190, NY-912M). |
| North Carolina | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 38,000 lb | Tandem 38,000 lb (grandfather 1956). |
| North Dakota | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 105,500 lb LCV on all NN routes. |
| Ohio | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 127,400 lb LCV (two trailers) or 115,000 lb (three trailers) on the Ohio Turnpike; single 21,000 lb. |
| Oklahoma | 102 in | 14 ft | 59.5 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 90,000 lb LCV (doubles). |
| Oregon | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 105,500 lb LCV (two trailing units all NN routes; three units on listed segments). |
| Pennsylvania | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | Axle weights vary by configuration on I-99 (Bedford to Bald Eagle). |
| Rhode Island | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 22,400 lb | 44,800 lb | Single 22,400 lb, tandem 44,800 lb. |
| South Carolina | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 35,200 lb | Tandem 35,200 lb. |
| South Dakota | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 129,000 lb LCV on listed routes (US-14, US-85, US-281, SD-50). |
| Tennessee | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Texas | 102 in | 14 ft | 59 ft | 65 ft | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Utah | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 129,000 lb LCV on I-15, I-70, I-80, I-84, I-215, UT-201. |
| Vermont | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 22,400 lb | 36,000 lb | Single 22,400 lb, tandem 36,000 lb (state limits can apply to the Interstate System). |
| Virginia | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Washington | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | 105,500 lb LCV on all NN routes (except SR 410 and SR 123 near Mt. Rainier). |
| West Virginia | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | – |
| Wisconsin | 102 in | 13 ft 6 in | 53 ft | – | 80,000 lb | 20,000 lb | 34,000 lb | Gross and axle limits vary by commodity on I-39 (Portage to Wausau); see the state profile. |
| Wyoming | 102 in | 14 ft | 53 ft | – | 80,000 lb | 20,000 lb | 36,000 lb | 117,000 lb LCV; tandem 36,000 lb (all NN routes). |
Height notes: Louisiana and Missouri allow 14 ft on the Interstate and 13 ft 6 in on other roads. Maine allows 14 ft with load and caps the Maine Turnpike at 13 ft 6 in. Arizona drops to 13 ft 6 in on Table 4 restricted routes. Oklahoma drops to 13 ft 6 in on county roads. Alaska allows 17 ft on the Dalton and Elliott highways between the Fox Weigh Station and Prudhoe Bay. Semitrailer notes: Florida allows 49 ft to 57 ft with kingpin conditions. Alaska allows 53 ft on designated highways with a kingpin distance of 41 ft or less. Overall length: only ten states set a limit; the federal rules bar an overall limit for a tractor-semitrailer on the National Network.
How do you use the State Legal Limits Checker?
- Enter the width in inches, the height in feet and inches, the semitrailer length in feet and the overall combination length when the rig has one.
- Enter the gross vehicle weight in pounds and the heaviest single axle and tandem axle group when the scale ticket shows them.
- Pick the route type and pick one state or all 50 states plus the District of Columbia.
- Read the verdict, the check table and the per-state verdicts. Over means the rig breaks that state limit. Exception means a grandfathered rule may cover it on the named road.
- Read the notes. Michigan axle caps, the bridge formula and the Alaska state formula all appear as notes when they apply.
- Copy the summary for the dispatch file, or reset the checker to start over.
Frequently asked questions
What is the legal truck height in most states?
13 ft 6 in. That is the limit in 26 states plus the District of Columbia. Nineteen states allow 14 ft, Colorado and Nebraska allow 14 ft 6 in and Alaska allows 15 ft. Louisiana and Missouri allow 14 ft on the Interstate and 13 ft 6 in on other roads. There is no federal height limit.
Which states allow 14 ft truck height?
Arkansas, Arizona, California, Hawaii, Idaho, Kansas, Maine with load, Montana, North Carolina, North Dakota, Nevada, New Mexico, Oklahoma, Oregon, South Dakota, Texas, Utah, Washington and Wyoming. Louisiana and Missouri also allow 14 ft, but only on the Interstate. Arkansas raised its limit to 14 ft in 2021 and North Carolina raised its limit after 2015, so older tables may still show 13 ft 6 in for both.
How wide can a truck be in Hawaii?
108 in, or 9 ft. Hawaii is the only state above the federal 102 in width limit under 23 CFR 658.15. A trailer at 108 in is legal in Hawaii and over width in the other 49 states plus the District of Columbia. Width is measured across the widest part of the load, not across the mirrors.
Can a truck run at 164,000 lb in Michigan?
Yes, on the Interstate and on designated state highways, under a grandfathered right that predates the federal limits. The catch is in the axles: Michigan caps a single axle at 18,000 lb and a tandem at 32,000 lb, both lower than the federal figures. A Michigan train spreads the weight across 11 axles. A rig with a 20,000 lb single axle is over in Michigan even when the gross weight is legal.
Does the federal government set a truck height limit?
No. The Federal Highway Administration sets no national maximum height. Height is a state rule, which is why the limit runs from 13 ft 6 in in most states to 15 ft in Alaska. The federal rules do set a width limit of 102 in, a semitrailer floor of 48 ft and a gross weight limit of 80,000 lb.
What is a grandfathered truck weight exception?
A state weight limit that predates the federal limits and survived them. States that allowed heavier weights on the dates Congress set kept the right to allow those weights on the Interstate. The Federal Highway Administration lists them in the Compilation of Existing State Truck Size and Weight Limit Laws, Appendix B. The exceptions apply only on the roads and vehicle configurations the state rule names.
Related tools
- Federal Size Limits Checker: check a rig against the federal floor: 102 in width, the 48 ft semitrailer floor, 80,000 lb gross weight and the axle limits.
- Kingpin Law Checker: check the kingpin-to-rear-axle distance against the state rule, including the California 40 ft limit and the Florida conditions.
- Axle Weight Rebalance Calculator: work out how far to slide the fifth wheel or the tandems when one axle group is heavy.
- Bridge Formula Axle Weight Checker: run the axle spacings against the bridge formula in 23 USC 127.
- Escort and Pilot Car Checker: work out when an escort vehicle is required and how many the state wants.
- Oversize Permit Cost Calculator: estimate the permit fees for a multi-state oversize run.
- Trucking Tools: browse every free calculator on Trucking Mind.
Sources
- 23 CFR 658.13, 658.15, 658.17 and Part 658 Appendix C. ecfr.gov/current/title-23/part-658 Accessed November 19, 2026.
- Federal Highway Administration, Compilation of Existing State Truck Size and Weight Limit Laws, Appendix B (May 2015, laws as of October 1, 2012). ops.fhwa.dot.gov/publications/fhwahop15029/index.htm Accessed November 19, 2026.
- Alaska Administrative Code, 17 AAC 25.012 and 17 AAC 25.013. dot.state.ak.us/cvlp Accessed November 19, 2026.
- Arkansas Code 27-35-207, as amended by Act 871 of 2021. arkleg.state.ar.us Accessed November 19, 2026.
- Arizona Revised Statutes 28-1094 and 28-1095; Ariz. Admin. Code R17-6-102 Table 1. azleg.gov/ars/28/01094.htm Accessed November 19, 2026.
- California Vehicle Code 35250. leginfo.legislature.ca.gov Accessed November 19, 2026.
- Colorado Revised Statutes 42-4-504. leg.colorado.gov/colorado-revised-statutes Accessed November 19, 2026.
- Florida Statutes 316.515. leg.state.fl.us Accessed November 19, 2026.
- Kansas Statutes 8-1904. kslegislature.gov Accessed November 19, 2026.
- Louisiana Revised Statutes 32:381. legis.la.gov Accessed November 19, 2026.
- Maine Revised Statutes Title 29-A, 2380. legislature.maine.gov Accessed November 19, 2026.
- Missouri Revised Statutes 304.170. revisor.mo.gov Accessed November 19, 2026.
- North Carolina General Statutes 20-116. ncleg.gov Accessed November 19, 2026.
- Nebraska Department of Transportation, Legal Sizes and Weights. dot.nebraska.gov/business-center/trucking Accessed November 19, 2026.
- New York Vehicle and Traffic Law 385. nysenate.gov/legislation/laws/VAT/385 Accessed November 19, 2026.
- Texas Transportation Code 621.207. statutes.capitol.texas.gov Accessed November 19, 2026.
- Haul Handbook, Legal Truck Size Limits. haulhandbook.com/legal-truck-size-limits Accessed November 19, 2026.
- ATS, State Truck Size and Weight Limits. atsinc.com/resources/state-truck-size-and-weight-limits Accessed November 19, 2026.