Skip to main content

Trucking Mind

The permit controls the move. This checker gives the general sign, flag and light rule for your load in each verified state. The permit can add signs, flags, lights or escorts for the route, the time of day, a bridge restriction or a construction zone. Read the permit before the wheels turn. No federal rule sets an OVERSIZE LOAD sign: each state writes its own.

Pick a state and enter the load size. Every answer updates as you change each field.

The state and the load

Measure the load at its widest, tallest and longest point, including any overhang. Width and height run to 30 ft. Length runs to 300 ft. Side overhang is the distance the load sticks out past the side of the vehicle. The width of the rear overhang decides whether 1 flag or 2 flags go at the rear.

Time of the move

Night means the hours when headlamps are required. At night, lamps replace flags on projections. Some states add their own lamp rules.

Signs plus flags in Florida

Signs front and rear, flags at the extremities.

Sign triggers: over 10 ft wide. Flag triggers: over 10 ft wide. Federal flags apply: 1 flag at the rear for a 5 ft overhang 2 ft wide.

The checks

CheckResultDetail
OVERSIZE LOAD signRequiredSign triggers: over 10 ft wide.
FlagsRequiredFlag triggers: over 10 ft wide. All four corners plus the extreme ends of protrusions.
Night lightsDay moveNo night lamps for a daylight move. Check the permit for any night restriction.
Federal baselineFlags apply49 CFR 393.87: 18 in red or orange fluorescent flags at the extremities of the projection.
Rule statusVerified primarySource: Fla. Admin. Code 14-26.012; FDOT Blanket Permit Movement Conditions, rev. 27 Jul 2026.

The figures

FigureValueNote
Sign size7 ft by 18 inLoad sign
Letter height12 inBrush stroke: 1.5 in
Sign wordingOVERSIZE LOADExact wording in the rule
Sign placementFront and rear, two signsMounting in the rule
Flag size18 in squareAll four corners plus the extreme ends of protrusions
Flags at the rear1Rear overhang 5 ft, 2 ft wide
State ruleFla. Admin. Code 14-26.012; FDOT Blanket Permit Movement Conditions, rev. 27 Jul 2026Verified 19 Nov 2026

What to do

  • Mount a 7 ft by 18 in OVERSIZE LOAD sign front and rear, two signs.
  • Mount flags: All four corners plus the extreme ends of protrusions.
  • Remove the signs and flags when the load is legal size again.

Documents and sources

  • Keep the permit in the cab. Its conditions govern the move.
  • Source: Fla. Admin. Code 14-26.012; FDOT Blanket Permit Movement Conditions, rev. 27 Jul 2026.
  • Federal baseline: 49 CFR 393.87 and 49 CFR 393.11.

Notes

  • No extra notes for this result.

All 50 states at these dimensions

StateSignFlagsRule status
AlabamaNot verifiedNot verifiedNot verified
AlaskaNot verifiedNot verifiedNot verified
ArizonaSignFlagsVerified primary
ArkansasNot verifiedNot verifiedNot verified
CaliforniaSignFlagsVerified primary
ColoradoSignFlagsVerified primary
ConnecticutNot verifiedNot verifiedNot verified
DelawareNot verifiedNot verifiedNot verified
District of ColumbiaNot verifiedNot verifiedNot verified
FloridaSignFlagsVerified primary
GeorgiaSignFlagsVerified primary
HawaiiNot verifiedNot verifiedNot verified
IdahoSignFlagsVerified primary
IllinoisSignFlagsVerified primary
IndianaNot verifiedNot verifiedNot verified
IowaSignFlagsVerified concordant
KansasSignFlagsVerified primary
KentuckyNot verifiedNot verifiedNot verified
LouisianaNot verifiedNot verifiedNot verified
MaineNot verifiedNot verifiedNot verified
MarylandNot verifiedNot verifiedNot verified
MassachusettsNot verifiedNot verifiedNot verified
MichiganSignFlagsVerified concordant
MinnesotaNo signFlagsVerified primary
MississippiNot verifiedNot verifiedNot verified
MissouriSignFlagsVerified primary
MontanaSignFederal onlyVerified primary
NebraskaSignFederal onlyVerified primary
NevadaSignFlagsVerified primary
New HampshireNot verifiedNot verifiedNot verified
New JerseyNot verifiedNot verifiedNot verified
New MexicoSignFlagsVerified primary
New YorkSignFlagsVerified primary
North CarolinaSignFlagsVerified primary
North DakotaNot verifiedNot verifiedNot verified
OhioSignFlagsVerified primary
OklahomaSignFlagsVerified primary
OregonSignFlagsVerified primary
PennsylvaniaSignFlagsVerified primary
Rhode IslandNot verifiedNot verifiedNot verified
South CarolinaNot verifiedNot verifiedNot verified
South DakotaNot verifiedNot verifiedNot verified
TennesseeNot verifiedNot verifiedNot verified
TexasEscort signFlagsVerified primary
UtahSignFlagsVerified primary
VermontNot verifiedNot verifiedNot verified
VirginiaNot verifiedNot verifiedNot verified
WashingtonSignFlagsVerified primary
West VirginiaNot verifiedNot verifiedNot verified
WisconsinSignFlagsVerified primary
WyomingSignFlagsVerified primary

This checker applies the state rule plus the federal flag and lamp rules to your inputs. Confirm the result against the permit conditions before the move. The permit governs.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is a planning estimate based on state rules read on 19 Nov 2026, not legal advice — confirm the sign, flag and light requirements on the permit for the move before the wheels turn.

Quick answer: Oversize load sign requirements come from the states, not from the federal government. No federal rule sets an OVERSIZE LOAD sign. Each state writes its own sign, flag and light conditions into the oversize permit. Most states require a 7 ft by 18 in yellow sign with black letters on the front and rear of the load once the load passes a width, height or length trigger. The common width trigger is 10 ft. The common letter height is 10 in. Flags are different: the federal rule at 49 CFR 393.87 sets an 18 in square red or orange fluorescent flag for any load that sticks out more than 4 in past the side of the vehicle or more than 4 ft past the rear, in every state. This checker runs your dimensions against the verified state rule for each state on the route, plus the federal flag and lamp rules. It shows the sign size, the wording, the flag size and the placement for that state.

Last reviewed: · Focus keyword: oversize load sign requirements

What is the federal rule for oversize load signs?

There is none. No section of the Federal Motor Carrier Safety Regulations sets an OVERSIZE LOAD sign, its size, its wording or when it must be displayed. The federal rules cover lamps and flags on projections, not signs. Every sign requirement on an oversize move comes from the state that issued the permit. The conditions printed on that permit are the enforceable terms for the move. A driver who crosses five states on one move follows five different sign rules. The permit for each state names its own.

The federal floor still matters, because it applies in every state on top of the state rule. Section 393.87 of 49 CFR says a load that extends more than 4 in beyond the sides of the vehicle or more than 4 ft beyond the rear must have the extremities marked with red or orange fluorescent warning flags, each at least 18 in square. One flag goes at the extreme rear if the projection is 2 ft wide or less. Two flags go at the rear if the projection is wider. The flags must sit where they mark the maximum width of the projection. That rule covers every load in every state, permitted or not. No state rule can waive it.

At night the federal rule adds lamps. Table 1 of 49 CFR 393.11, footnotes 9 and 10, sets the lamps for projections during the hours when headlamps are required. A side projection over 4 in needs an amber lamp at the foremost edge, visible from the front and the side, plus a red lamp at the rearmost edge, visible from the rear and the side. A short projection, 3 ft or less from front to rear, needs a single amber lamp visible from the front, both sides and the rear, or a red lamp if it sits at or near the rear. A rear projection over 4 ft needs one red side marker lamp on each side showing the maximum overhang, plus two red lamps and two red reflectors on the rear, one at each side, showing the maximum width. The checker applies both federal rules to every result, in every state, including the states whose own rule is not verified.

The practical point is that the sign and the flag come from different authorities. The sign is a state permit condition, with a different trigger and a different size in each state. The flag is a federal safety rule with one size everywhere. A move can need a federal flag and no state sign, or a state sign and no federal flag, or both, or neither. The checker separates the two so the driver sees which authority requires what. Before planning the marking for a move, check whether the load is oversize at all with the Federal Size Limits Checker, which works out the federal legal size limits for the vehicle, plus the State Legal Limits Table, which lists the legal width, height and length limit in each state.

How big must an OVERSIZE LOAD sign be?

The most common size in the country is 7 ft long by 18 in high. That is the size Florida, Illinois, Missouri, Nebraska, New York, North Carolina, Ohio, Oregon, Pennsylvania, Utah, Washington and Wisconsin require. It is the size most sign makers stock. The letters on a 7 ft by 18 in sign are usually 10 in high, with a brush stroke around 1.41 in. A few states ask for more: Florida and Illinois require 12 in letters. Pennsylvania requires a 2 in brush stroke. New York allows a 2 in stroke when Series E Modified lettering is used. The sign is almost always black letters on a yellow background. The checker shows the exact size, letter height and stroke for the state selected.

Five verified states use a smaller sign. A driver who carries only the standard 7 ft by 18 in sign can still be legal there, because every state rule sets a minimum size, not an exact size. Oklahoma requires at least 5 ft by 14 in, with 8 in letters and a 1.125 in brush stroke. New Mexico requires at least 5 ft by 12 in, with letters at least 10 in high by 1 in wide. Idaho requires a minimum of 5 ft by 12 in, with 8 in letters and a 1 in stroke, under the 2024 permit attachment. Arizona requires 6 ft by 1 ft with 6 in letters. Wyoming requires at least 60 in by 10 in, with 8 in letters and a 1 in brush stroke. Colorado allows either 5 ft by 10 in with 8 in letters or 7 ft by 18 in with 10 in letters, at the choice of the carrier. A 7 ft by 18 in sign with 10 in letters meets or beats every one of those minimums on size and letter height, which is why most carriers carry one size and use it everywhere.

Four verified states set no overall sign size at all. Montana sets only the letter height, 8 in, black on yellow. It leaves the sign dimensions to the carrier. Nevada sets the letter height at 10 in with a 1.625 in stroke and says the sign may be two pieces, but sets no overall size. Minnesota sets flashing amber lights plus reflective letters visible 500 ft. The provisions read set no sign dimensions. Michigan sets its signing requirements in numbered special provisions printed on the permit. The sources read state no sign size. In those states the permit governs. A standard 7 ft by 18 in sign is the safe choice.

Two states allow a split sign. North Carolina says the 7 ft banner may be two pieces totaling 7 ft. Nevada says the sign may be two pieces. That matters on a narrow load, where a single 7 ft sign will not fit across the front of the vehicle. The two pieces go side by side so the full legend reads across the width of the vehicle. New York sets a mounting height as well: the sign must sit at least 2 ft above the surface of the road and not more than 5 ft, placed so it can be read from at least 400 ft behind the vehicle. California sets a minimum mounting height of 18 in above the road. Most states set no mounting height. The rule is simply that the sign must be clearly visible.

What must an oversize load sign say?

OVERSIZE LOAD is the standard wording in most states. It is the wording the checker shows unless the state rule says otherwise. The sign reads the same on the front and on the rear of the load. The letters are black on a yellow background in every verified state that names colors. Georgia is the one exception on wording that catches drivers out: the Georgia rule spells the sign OVERSIZED LOAD, with a D. A sign that reads OVERSIZE LOAD does not match the Georgia rule as written. A driver running Georgia with a standard sign should know the difference before the move, not at the scale.

New Mexico uses a different set of words entirely. The New Mexico rule says the load sign must read OVERSIZE, OVERWIDTH, OVERLENGTH or OVERHEIGHT, matching the dimension that makes the load oversize. The words OVERSIZE LOAD belong to the escort vehicle sign in New Mexico, not to the load sign. California uses OVERSIZE on the standard sign and LONG LOAD on a load over 100 ft long. It allows WIDE LOAD, LONG LOAD, OVERSIZE LOAD, EXCESSIVE FRONT OVERHANG or EXCESSIVE REAR OVERHANG as substitutes. Oregon allows WIDE LOAD on an overwidth load under 80 ft long and LONG LOAD on a load over 80 ft long that is not over 8 ft 6 in wide. Colorado lets the carrier pick the wording that fits the load: Wide Load, Wide, Long Load, Long, Oversize Load or Oversize. Montana accepts OVERSIZE LOAD or similar wording. Nevada accepts OVERSIZE LOAD or OVERSIZE. Missouri accepts OVERSIZE LOAD or WIDE LOAD. Texas puts OVERSIZE LOAD or WIDE LOAD on the escort vehicle. No sign goes on the load itself.

The wording matters because an inspector reads the sign against the permit conditions. A sign that says the wrong thing is the same as a sign that is the wrong size: the permit condition is not met. The checker shows the exact wording from the rule for the state selected, including the Georgia D and the New Mexico word set, so the driver can check the sign on the truck against the rule before the move. For a Texas leg, the Texas Oversize Sign and Flag Requirements tool covers the Texas escort sign rules in full. The Texas Overweight Permit Wizard walks through the Texas permit itself.

One more wording rule is easy to miss: several states require the sign to be removed when the load is legal size again. Kansas says the signs must be removed when the vehicle is within legal limits. Nevada requires the signs and flags only when necessary and says to remove them promptly on arrival. Montana says the signs must be removed after the movement. A sign left up on an empty return trip can draw a stop, because it tells every inspector on the road that the vehicle is running oversize when it is not.

When are flags required on an oversize load?

Flags are required in two different ways. The checker keeps them separate. The federal rule at 49 CFR 393.87 requires flags on any projection: a load that sticks out more than 4 in past the side of the vehicle, or more than 4 ft past the rear, needs red or orange fluorescent flags at the extremities of the projection, in every state, day or night. That rule applies whether the load has a permit or not. A legal width load with a long rear overhang needs federal flags even though it needs no sign and no permit.

The state flag rules sit on top of the federal rule and usually fire at a lower threshold than the state sign rule, or at the same threshold. Arizona requires flags on overwidth or overlength vehicles and loads, which means any load over 8 ft 6 in wide or over 65 ft long. North Carolina requires flags on all sides at the widest point for any load over 8 ft 6 in wide, while its sign trigger is 10 ft. Minnesota requires flags when the load is over 9 ft wide or 75 ft long, while its sign trigger is 12 ft 6 in wide or 95 ft long. Nebraska is the reverse: its sign trigger is 10 ft wide, but its flag trigger is 12 ft wide, so a load 11 ft wide needs signs but no state flags. The checker shows both triggers for the state selected, so the split is visible before the move.

Several states tie the flag rule to the same trigger as the sign rule. Florida, Iowa and Illinois require flags on the same loads that require signs. Pennsylvania and Nevada require flags on all permitted oversize vehicles, the same population that requires signs. New Mexico requires every oversize vehicle, combination and load to be properly flagged at all times. Ohio requires flags on all overdimensional vehicles and loads. Kansas requires flags on each side of the widest part of an overwidth load plus the rear of an overlength load. Montana is the one verified state where the rule read sets no flag rule at all, so the federal flag rule is the only flag rule in Montana. The checker says so.

Rear overhang has its own flag trigger in most states. The number matters. The federal rule sets it at more than 4 ft. Idaho, Michigan, Oregon and Wyoming set it at 4 ft or more, which is a lower line: a rear overhang of exactly 4 ft needs a flag in those states and not under the federal rule. Utah and Minnesota set it at more than 4 ft, matching the federal line. New Mexico flags a rear overhang of 4 ft or more, plus a front overhang of 3 ft or more on a single vehicle or 2 ft or more on a combination. Utah flags a front overhang over 3 ft. The checker applies the state line where the state sets one, plus the federal line everywhere. It shows which one fired.

What size flags does the law require?

The federal flag is 18 in square. That size is the safe choice in every state. Section 393.87 requires each flag to be at least 18 in square, red or orange fluorescent. Every verified state that sets a flag size sets 18 in, with three exceptions that set a smaller minimum. Kansas requires flags at least 12 in square. Texas requires flags at least 12 in square. Wyoming requires 12 in square flags under the concordant permit guides. In all three states an 18 in flag satisfies the minimum, because the rule sets a floor, not an exact size. A driver who carries 18 in flags is legal on flag size in every verified state.

Four verified states set no flag size in the rule text read. California sets the flag requirement in the permit guides but the Caltrans FAQ read states no flag size. Colorado sets the flag placement but no flag size in the rule text read. Montana sets no flag rule at all in the rule read. Washington sets the flag placement in the rule but no flag size in the excerpt read. In those states the federal 18 in flag is the practical answer. The checker says the size is not stated in the rule and to use 18 in flags. The checker never invents a size where the rule is silent.

The color rule is consistent across the country. Flags must be red, orange, fluorescent red or fluorescent orange. New Mexico allows red, fluorescent red or fluorescent orange, square or rectangular, at least 18 in on any one side. Illinois requires clean bright red flags. Wisconsin requires solid red or orange flags. Nevada requires solid red or fluorescent orange flags. The word clean matters in practice: a faded flag, a torn flag or a flag caked in road dirt does not meet a rule that says clean and bright. An inspector can cite it. Flags are cheap. Replace them when the color fades.

Flag material is set in only a few rules. Arizona says the flags must be cloth or plastic. New York requires the flags on staffs, mounted so they stand out from the load and stay visible. Most states say nothing about material. The usual practice is a cloth or vinyl flag on a staff or a magnetic mount, fixed so it cannot fold back against the load at speed. A flag that folds flat against the load marks nothing. The rule in every state is about marking the extremity, not about carrying a flag somewhere on the truck.

Where do the flags go?

The short answer is the corners and the widest points. The long answer depends on the shape of the load. The federal rule says the flags must be located to indicate the maximum width of the projection, which means the flag goes at the point that sticks out farthest, not at a convenient point. On a rectangular load the widest points are the four corners. Most state rules say so directly: Florida, Nebraska, New Mexico, New York, Ohio and Wyoming all require flags at the four corners, or at the corners of the load where the load is wider than the vehicle. Nevada says the flags go at each front and rear corner of the vehicle. If the load is wider than the vehicle, at each corner of the load plus anywhere else needed to mark the maximum width.

A load that is wider in the middle than at the ends needs extra flags. Wisconsin says a flag goes at the widest point if any part of the load is over 4 in wider than the front or rear width. Michigan says a flag goes at the widest point on each side if it extends beyond the corner flags. North Carolina says the flags go on all sides at the widest point, mounted so as not to increase the overall width. That last point matters: a flag staff that sticks out past the load adds width to the load. In North Carolina the rule says not to do it. Mount the flag so the cloth marks the edge without the staff adding to the width.

The rear overhang has its own placement rule. It turns on the width of the overhang. The federal rule says one flag at the extreme rear if the projection is 2 ft wide or less. Two flags go at the extreme rear if it is wider. Idaho, Minnesota, Ohio, Wisconsin and Wyoming follow the same 2 ft line. Nevada puts one flag at the center of a rear overhang 2 ft wide or less. Nevada puts one flag at each rear corner if it is wider. New Mexico puts a flag on each corner of the overhang, or one flag if the overhang is under 2 ft wide. The checker asks for the width of the rear overhang and works out whether the rear needs 1 flag or 2. A driver who guesses the count can end up with one flag where the rule requires two, which is the most common flag error at a scale.

Front overhang is flagged in fewer states, but the rule is the same shape where it exists. New Mexico flags a front overhang of 3 ft or more on a single vehicle and 2 ft or more on a combination. Utah flags a front overhang over 3 ft. Minnesota flags an overhang over 4 ft at either end. California allows an overhang of up to 10 ft before the flag rule in the permit guides fires. Where no state rule covers a front overhang, the federal side projection rule may still apply if the overhang sticks out past the side of the vehicle. The checker asks for the front overhang and applies the state rule where one exists.

What changes at night?

At night, lamps replace flags on projections. The federal lamp rule is the floor in every state. Section 393.11 Table 1 requires lamps on a side projection over 4 in and on a rear projection over 4 ft during the hours when headlamps are required. An amber lamp marks the foremost edge of a side projection, visible from the front and the side. A red lamp marks the rearmost edge, visible from the rear and the side. A rear projection over 4 ft needs a red side marker lamp on each side showing the maximum overhang, plus two red lamps and two red reflectors on the rear, one at each side, showing the maximum width. The lamps must be visible at the distances the regulation sets. A dead lamp is the same as no lamp.

Several states add their own night rules on top of the federal lamps. New York requires amber lights on the forward corners and red lights on the rear corners of an overwidth load at night, plus red lights on the rear corners and amber lights at least every 6 ft along the side of an overhang portion over 2 ft long. The New York sign face must be high intensity reflective material for a night move. Minnesota requires steady lights at the widest points, at the end of an overhang over 4 ft, plus every 20 ft along the outside of the load. Missouri requires the signs to be lighted or reflectorized at night, with amber lights standing in place of flags. Oregon requires the signs to be reflectorized from one half hour after sunset to one half hour before sunrise. Washington requires lights where flags are required at night. Michigan requires a red light or lantern at the end of a rear overhang 4 ft or more at night. North Carolina allows a red or amber light visible 200 ft at the end of a rear overhang over 4 ft at night, in place of the daytime flag.

Warning lights on the vehicle are a separate requirement from the projection lamps. They apply in daylight too in several states. Illinois requires an amber rotating or flashing light on every oversize or overweight permit load, visible 500 ft, with a second light within 10 ft of the rear on a load over 80 ft long. Florida requires Class 2 amber warning lights at the same triggers as the sign, visible 500 ft. Montana requires flashing amber lights at each end of the sign on the power unit, at least 5 in in diameter, 50 candlepower, 60 to 90 flashes per minute, visible 360 degrees, flashing at all times when moving. Iowa requires an amber revolving light at least 7 in high or in diameter when the length is over 85 ft, the front overhang is over 25 ft, the rear overhang is over 10 ft, or the weight is over 80,000 lb. Wyoming requires a revolving amber light, a strobe, or two 2-way flashing amber lights at least 4 in in diameter at night. The checker shows the state light rule where one was read, plus the federal lamp rule everywhere.

Night moves are also restricted by time in many states. A lamp that is legal at 9 pm may not matter if the permit forbids movement after dark. The checker covers signs, flags and lights only. For the hours a load may move, use the Oversize Curfew and Holiday Checker, which covers the curfew and holiday travel windows by state. For the escort rules that often change at night, use the Escort and Pilot Car Checker, which works out how many pilot cars a load needs in each state.

Do you need a sign when the load is only overweight?

In most states, no. A load that is overweight but within the legal width, height and length limits usually needs no OVERSIZE LOAD sign, because the sign marks a load that is too big, not a load that is too heavy. Washington, Colorado and Idaho each say so directly: no sign or flag is required for an overweight only load. The permit still applies. The permit may still require warning lights or escorts for the weight, but the sign itself is tied to dimensions, not to weight. Illinois is the exception on lights: its amber rotating or flashing light is required on every oversize or overweight permit load, so an overweight only load in Illinois needs the light even though it needs no sign.

Kansas is the one state where the sources conflict. The checker flags the conflict rather than picking a side. The regulation at K.A.R. 36-1-36(s)(2) requires signs on oversize and overweight loads. A summary of the statute at K.S.A. 8-1911(l) says a load within legal width and length must not display the sign. Those two readings cannot both be right for the same move. The checker tells the driver to read the permit for an overweight only move in Kansas. The permit conditions for the specific move are the authority that resolves the conflict. No general tool can resolve it in advance.

The same logic applies to the federal flag rule. A load that is overweight but not overhanging needs no federal flag, because section 393.87 turns on projections, not on weight. A load that is overweight and overhanging needs the federal flag for the overhang, regardless of the weight. The checker asks for dimensions and overhangs, not for weight, because weight does not change the sign or flag answer in any verified state except through the Kansas conflict and the Illinois light rule, both of which the checker notes where they apply.

Weight does change the permit, the escorts and the route, even when it does not change the sign. A heavy load may need a superload permit, a route survey or a bridge review that a light oversize load does not need. The Superload Threshold Checker works out whether a load counts as a superload in each state. The Trip Permit Checker covers the temporary trip permit for a move into a state where the carrier is not registered. The Oversize Cost Calculator works out the cost of an oversize move, including permits, escorts and pilot cars.

Oversize sign and flag rules by state

The table below lists the sign trigger, the sign size and the flag size for every state, plus the District of Columbia, as verified on 19 Nov 2026. Primary means the rule text was read from the state code, the DOT rule or the DOT permit attachment. Concordant means two or more independent secondary permit guides agree and no primary text was read. Not verified means no primary source was read and the secondaries conflict or are absent: the checker shows the federal flag rule for those states and tells the driver to follow the permit. The table is a summary. The checker above gives the full rule for the state selected, including the wording, the placement and the light rules.

StateSign triggerSign sizeFlag sizeStatus
AlabamaNot verifiedNot verifiedNot verifiedNot verified
AlaskaNot verifiedNot verifiedNot verifiedNot verified
Arizona9 ft wide or more6 ft by 1 ft18 inPrimary
ArkansasNot verifiedNot verifiedNot verifiedNot verified
CaliforniaOver 8 ft 6 in wide or over 80 ft longNot statedNot statedPrimary
ColoradoAny oversize load5 ft by 10 in or 7 ft by 18 inNot statedPrimary
ConnecticutNot verifiedNot verifiedNot verifiedNot verified
DelawareNot verifiedNot verifiedNot verifiedNot verified
District of ColumbiaNot verifiedNot verifiedNot verifiedNot verified
FloridaOver 10 ft wide, over 80 ft long, or over 14 ft 6 in high7 ft by 18 in18 inPrimary
GeorgiaOver 8 ft 6 in wide, over 13 ft 6 in high, or over 100 ft long6 ft by 1 ft18 inPrimary
HawaiiNot verifiedNot verifiedNot verifiedNot verified
IdahoOver 8 ft 6 in wide5 ft by 12 in18 inPrimary
IllinoisOver 10 ft wide, over 14 ft 6 in high, or over 75 ft long7 ft by 18 in18 inPrimary
IndianaNot verifiedNot verifiedNot verifiedNot verified
IowaOver 8 ft 6 in wide, over 14 ft 4 in high, or over 75 ft long7 ft by 18 in18 inConcordant
KansasAny oversize or overweight load7 ft by 18 in12 inPrimary
KentuckyNot verifiedNot verifiedNot verifiedNot verified
LouisianaNot verifiedNot verifiedNot verifiedNot verified
MaineNot verifiedNot verifiedNot verifiedNot verified
MarylandNot verifiedNot verifiedNot verifiedNot verified
MassachusettsNot verifiedNot verifiedNot verifiedNot verified
MichiganAny overdimensional loadNot stated18 inConcordant
MinnesotaOver 12 ft 6 in wide or over 95 ft longNot stated18 inPrimary
MississippiNot verifiedNot verifiedNot verifiedNot verified
MissouriOver 10 ft 6 in wide, or over 110 ft long (rear sign)7 ft by 18 in18 inPrimary
MontanaOver 10 ft wideNot statedNot statedPrimary
NebraskaOver 10 ft wide7 ft by 18 in18 inPrimary
NevadaAny oversized vehicleNot stated18 inPrimary
New HampshireNot verifiedNot verifiedNot verifiedNot verified
New JerseyNot verifiedNot verifiedNot verifiedNot verified
New MexicoAny oversize vehicle, combination or load5 ft by 12 in18 inPrimary
New YorkOver 8 ft 6 in wide or over 65 ft long7 ft by 18 in18 inPrimary
North CarolinaOver 10 ft wide7 ft by 18 in18 inPrimary
North DakotaNot verifiedNot verifiedNot verifiedNot verified
OhioOver 10 ft wide, over 14 ft 6 in high, or over legal length7 ft by 18 in18 inPrimary
OklahomaAny oversize vehicle or load under permit5 ft by 14 in18 inPrimary
OregonOverwidth or overlength7 ft by 18 in18 inPrimary
PennsylvaniaAny permitted oversize vehicle7 ft by 18 in18 inPrimary
Rhode IslandNot verifiedNot verifiedNot verifiedNot verified
South CarolinaNot verifiedNot verifiedNot verifiedNot verified
South DakotaNot verifiedNot verifiedNot verifiedNot verified
TennesseeNot verifiedNot verifiedNot verifiedNot verified
TexasNo sign on the load; sign on the escort vehicle only5 to 7 ft by 12 to 18 in (escort)12 inPrimary
UtahOver 10 ft wide, over 14 ft 6 in high, or over 105 ft long7 ft by 18 inNot statedPrimary
VermontNot verifiedNot verifiedNot verifiedNot verified
VirginiaNot verifiedNot verifiedNot verifiedNot verified
WashingtonAny oversize load7 ft by 18 inNot statedPrimary
West VirginiaNot verifiedNot verifiedNot verifiedNot verified
WisconsinOver 10 ft wide or overlength7 ft by 18 in18 inPrimary
WyomingAny oversize load60 in by 10 in12 inPrimary

Indiana is the one state where the secondary sources disagree with each other and no primary text was read. One guide reproduces the Illinois text for Indiana. Another says the sign reads OVER-SIZE LOAD, 18 in by 6 to 8 ft, with 12 in letters and a 2 in stroke. A third says 6 to 7 ft by 18 in with 10 in letters. A fourth says signs on all permitted vehicles and loads with 18 in flags at the corners plus the widest point. With four different answers and no primary source, the honest entry is not verified. The driver should follow the Indiana permit conditions for the move.

How do you check signs and flags for a multi-state move?

Check every state on the route, one at a time, before the load is marked. The checker covers one state per run. The compare table in the results shows all 50 states at the same dimensions, so the full route is visible in one view. Start with the state where the load is widest relative to its trigger, because that state usually sets the strictest marking. Then work through the rest of the route in order. The sign that satisfies the strictest state on the route satisfies every state on the route for size, because every size rule is a minimum. The wording is the part that does not transfer: a sign that reads OVERSIZE LOAD does not match the Georgia rule. A sign that reads OVERSIZE LOAD does not match the New Mexico load sign rule either.

Carry the kit that covers the route. A 7 ft by 18 in OVERSIZE LOAD sign with 10 in letters covers the size rule in every verified state. Add a second sign with the Georgia OVERSIZED LOAD wording for a Georgia leg, plus a New Mexico OVERSIZE sign for a New Mexico leg. Carry 18 in flags: they satisfy the 12 in minimums in Kansas, Texas and Wyoming. They are the federal size everywhere. Carry staffs for New York, where the flags must be on staffs. Carry amber and red lamps for a night leg, plus spare bulbs. Carry a reflective sign face or a lighted sign for a night move in New York, Missouri or Oregon. The cost of the kit is small next to the cost of a stop at a scale.

Check the permit conditions against the checker result, not instead of it. The permit can add marking for a specific route, a bridge, a construction zone or a time of day. The permit conditions govern the move. If the permit and the checker disagree, the permit wins. If the permit is silent on a point the checker covers, the checker result is the general rule for that state. If the state is marked not verified, the permit is the only source. The driver should read it line by line before the move. The Kingpin Law Checker covers the kingpin to rear axle limits that affect how far a load can overhang on the trailer, which is often the reason a rear overhang flag is needed in the first place.

Plan the marking with the rest of the move, not after it. The escort rules, the curfew windows and the superload thresholds all change with the same dimensions that set the sign and flag rules. A load that needs signs in one state may need a pilot car in the next. A load that may move at noon may not move at midnight. Run the Escort and Pilot Car Checker for the pilot car count, the Oversize Curfew and Holiday Checker for the travel windows, plus the Superload Threshold Checker for the superload line, with the same dimensions used here. The four tools together give the full picture for the move.

What happens if the signs are wrong?

A wrong sign is a permit violation. The usual result is a stop at the scale or at the roadside. The inspector reads the sign against the permit conditions: the size, the wording, the placement and the flags. A sign that is too small, a sign that reads the wrong words, a missing rear sign, or a missing flag at the widest point are all the same kind of defect. The inspector can hold the vehicle until the marking is fixed. A hold at a scale costs the hours the move cannot spare. On a curfew move it can cost the whole travel window.

The more serious risk is the crash. Signs and flags exist so other drivers can judge the size of the load and give it room. A load that looks legal but is 12 ft wide will surprise a driver in the next lane. A rear overhang with no flag at the end is invisible in the dark. The flag and lamp rules are written around that risk. The federal rule is explicit that the flags must mark the maximum width and the maximum overhang. A flag mounted in the wrong place marks nothing. The rule is not met even though a flag is on the truck.

There is no single penalty figure for a wrong sign, because each state sets its own enforcement for a permit violation. The checker does not publish penalty figures without a source and a date. The practical cost is the delay, the re-marking at the roadside, plus the record of the violation on the carrier file. The cheapest fix is to check the marking before the wheels turn, with the permit in hand and the checker result printed or copied to the phone. The copy button on the checker puts the summary in the clipboard, ready to paste into a message to the driver or the pilot car.

How do you use the Oversize Sign and Flag Requirements Checker?

Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the verdict change.

  1. Pick the state for the leg of the move.
  2. Enter the load width, height and overall length in feet.
  3. Enter the side overhang in inches plus the front and rear overhangs in feet.
  4. Enter the width of the rear overhang, then pick daylight or night.
  5. Read the sign size, the wording, the flag size and the placement for that state.
  6. Copy the summary, then check the permit conditions before the move.

Measure the load before you start. The best input is a tape measure on the loaded vehicle: the widest point of the load, the tallest point, the overall length from the front of the power unit to the end of the load, plus the overhangs past the front and the rear of the trailer. The width of the rear overhang decides whether the rear needs 1 flag or 2, so measure that too. Guessing a dimension produces a guess. When a dimension is uncertain, run the tool twice: once with the low figure, once with the high figure. Read the range of results the two runs produce. The range tells you how much the uncertain figure matters.

Read the compare table after the single state result. It shows all 50 states at the same dimensions, so a multi-state route is visible in one view. A state marked not verified in the table needs the permit conditions read line by line, because the checker has no verified rule for it. A state marked Primary or Concordant shows the sign and flag answer from the rule text. The federal flag rule applies in every row of the table, including the not verified rows.

Questions drivers ask

Do all states require OVERSIZE LOAD signs?

No. There is no federal sign rule. Each state writes its own. Most states require a sign once the load passes a width, height or length trigger. The trigger differs by state. Texas puts no sign on the load itself: the sign rides on the escort vehicle. A few states require a sign on every permitted oversize load, whatever the dimensions. The checker shows the rule for the state selected.

How big is a standard OVERSIZE LOAD sign?

The most common size is 7 ft long by 18 in high, with 10 in black letters on a yellow background. Florida and Illinois require 12 in letters. Oklahoma requires 5 ft by 14 in, New Mexico and Idaho require 5 ft by 12 in, Arizona requires 6 ft by 1 ft. Wyoming requires 60 in by 10 in. A 7 ft by 18 in sign meets or beats every minimum size in the verified states.

How many flags do I need at the rear of an overhang?

One flag if the overhang is 2 ft wide or less, two flags if it is wider, under 49 CFR 393.87. Each flag must be at least 18 in square, red or orange fluorescent. The same 2 ft line applies in Idaho, Minnesota, Ohio, Wisconsin and Wyoming. Nevada puts one flag at the center of a narrow overhang and one at each rear corner of a wide one. The checker works out the count from the width you enter.

Do I need flags at night?

At night, lamps replace flags on projections under 49 CFR 393.11. A side projection over 4 in needs an amber lamp at the foremost edge and a red lamp at the rearmost edge. A rear projection over 4 ft needs red side marker lamps plus two red lamps and two red reflectors on the rear. Several states add their own night rules: New York requires amber lights on the forward corners and red lights on the rear corners of an overwidth load. The sign face must be high intensity reflective.

Do I need a sign if my load is only overweight?

In most states, no. The sign marks a load that is too big, not a load that is too heavy. Washington, Colorado and Idaho say so directly. Illinois still requires the amber warning light on an overweight only load. Kansas is the one state where the sources conflict: the regulation requires the sign on overweight loads, while a summary of the statute says the sign must not be displayed. Check the permit for an overweight only move in Kansas.

Where do I mount the OVERSIZE LOAD signs?

On the front and the rear of the load, where other drivers can read them. Most states say front and rear without more detail. North Carolina mounts the signs on the front and rear bumpers. New York requires the sign 2 to 5 ft above the road, readable from 400 ft behind the vehicle. California requires the sign at least 18 in above the road. Arizona allows the front sign on the roof of the power unit. The sign must not block lights, plates or required equipment.

Related tools

Sources

Follow on WhatsApp Ask by Voice