Skip to main content

Trucking Mind

One rig at a time. This checker runs one configuration against the federal size rules in 23 CFR Part 658 and 49 USC 31111 to 31114, plus the height limit in each state you pick. A result that needs a permit means the rig must not roll until the permit is in hand.

Pick the configuration, enter the dimensions, pick the states on the route. Every answer updates as you change each field.

The configuration

Length

Overall length is optional for a tractor-semitrailer or doubles combination: no federal overall limit applies there. It is required for the other configurations.

Width and height

Enter the height in decimal feet. A rig at 13 ft 6 in is 13.5. Measure at the tallest point, including the load and any roof equipment.

States on the route

The state picks set the height limit and, for a trailer over 53 ft, the grandfathered length. With no state picked, the height check uses the 13 ft 6 in figure that is legal in every state.

Legal with checks before you roll

The rig meets the federal size rules, with checks on Semitrailer length.

CheckResultDetail
Semitrailer lengthCheck53 ft. A 53 ft semitrailer runs on the National Network in every state except Hawaii, where the semitrailer limit is 48 ft (HRS 291-34). The federal floor is 48 ft (23 CFR 658.13(b)(1)).
Overall lengthInfo70 ft overall. No state may impose an overall length limit on a truck tractor-semitrailer combination (23 CFR 658.13(b)(3)).
WidthPass102 in. No state may impose a width limit of more or less than 102 in on the National Network (23 CFR 658.15(a)).
HeightPass13 ft 6 in. There is no federal height limit. At 13 ft 6 in or less the rig is legal in every state.
Kingpin-to-rear-axle distanceInfoA semitrailer over 48 ft must also meet each state kingpin-to-rear-axle limit. California allows 40 ft to the rearmost axle. Run the Kingpin Law Checker for the states on the route.

The figures

FigureValueNote
Semitrailer length53 ftFederal floor 48 ft. Kingpin limits apply
Overall length70 ftNo federal limit
Width102 inFederal limit 102 in
Height13 ft 6 inNo federal limit. Every state allows 13 ft 6 in

What to do

  • Slide the tandems to meet the tightest kingpin limit on the route before you cross a state line.

Notes

  • The federal size rules apply on the National Network: the Interstate System and designated Federal-aid Primary highways, plus reasonable access to terminals and services.
  • Devices listed in 23 CFR 658.16 do not count toward measured length or width. Each exclusion is specific and cannot be combined with another.

This checker applies 23 CFR Part 658 and 49 USC 31111 to 31114 to your answers, plus the height limit in each state you pick. It is not legal advice. Confirm the measurements with a tape before you rely on a result.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.

Quick answer: Federal law sets floors that every state must allow on the National Network: a 48 ft semitrailer, 28 ft twins, 102 in of width and no overall length limit on a tractor-semitrailer or doubles combination. There is no federal height limit at all. A 53 ft semitrailer is the standard rig on the National Network and 13 ft 6 in is legal in every state. This checker runs one configuration against those rules and the height limit in each state you pick.

Last reviewed: · Focus keyword: legal semi truck dimensions

What are the federal size limits for a semi truck?

Federal size law works by floors, not by ceilings. The Surface Transportation Assistance Act of 1982 and the rules that carry it out in 23 CFR Part 658 tell each state the minimum size it must allow on the National Network. A state may allow more. It may not allow less. The National Network is the Interstate System plus designated Federal-aid Primary highways, with reasonable access to terminals and services.

The floors are simple to state and easy to get wrong in practice. Length is measured on the trailer, not on the whole rig. Width is a hard number in both directions. Height is not a federal subject at all. The table below gives the headline numbers and the sections after it explain each one.

DimensionFederal rule on the National NetworkSource
Semitrailer lengthStates must allow at least 48 ft23 CFR 658.13(b)(1)
Twin trailer lengthStates must allow at least 28 ft each23 CFR 658.13(b)(2)
Overall length, tractor-semi or doublesNo federal limit23 CFR 658.13(b)(3)
Width102 in, no more and no less23 CFR 658.15(a)
HeightNo federal limitFHWA-HOP-04-022
Bus lengthStates must allow at least 45 ft23 CFR 658.13(d)
Auto transporter, traditionalStates must allow at least 65 ft23 CFR 658.13(e)(1)(i)
Auto transporter, stinger-steeredStates must allow at least 80 ft49 USC 31111(b)(1)(G)
Drive-away saddlemount97 ft23 CFR 658.13(e)(1)(iii)
Towaway trailer transporterStates must allow at least 82 ft49 USC 31111(b)(1)(H)

Two points trip people up. First, the federal rule protects the trailer length and the combination type, not the tractor. A state may set its own overall length limit off the National Network and it may set its own rules for a straight truck. Second, size and weight are separate subjects. A rig that is legal in size can still fail the axle weight limits or the bridge formula. Run the Bridge Formula Axle Weight Checker for the weight side of the same trip.

The checker on this page covers the federal size rules plus two state subjects that decide real trips: the height limit in each state you pick and the grandfathered semitrailer length for a trailer over 53 ft. It does not cover state length law beyond those two points. For the full state picture, use the State Legal Limits Table next to this checker.

Is there a federal height limit for trucks?

No. There is no federal height limit for commercial motor vehicles in the United States. The Federal Highway Administration states it plainly in its size regulations guide: there is no federal vehicle height requirement for commercial motor vehicles, so states may set their own height restrictions. Part 658 of Title 23 has sections for length, width and weight. It has no section for height.

Each state sets its own number. Most states cap height at 13 ft 6 in or 14 ft. Twenty states allow 14 ft on the main truck network, Colorado and Nebraska allow 14 ft 6 in and Alaska allows 15 ft. Twenty-seven states and the District of Columbia sit at 13 ft 6 in. The practical rule follows from those numbers: a rig at 13 ft 6 in or less is legal in every state and anything taller needs a state-by-state check.

Four states run two heights and the checker carries both. Arizona allows 14 ft generally and drops to 13 ft 6 in on routes restricted under its Table 4. Louisiana allows 14 ft only for a vehicle that operates exclusively on the Interstate and 13 ft 6 in everywhere else. Missouri allows 14 ft on the Interstate and designated routes and 13 ft 6 in on other highways. Oklahoma allows 14 ft and drops to 13 ft 6 in on county roads. Pick the states on the route and the checker shows the note for each one.

Legal height is not a clearance guarantee. A 14 ft rig that is legal in a 14 ft state still hits a bridge posted at 13 ft 6 in. North Carolina writes the point into its statute: the state owes no duty to raise a structure for a vehicle over 12 ft 6 in and the operator of a vehicle over that height is liable for the damage it causes.

Louisiana puts a matching duty on the operator of any vehicle over 13 ft 6 in to make sure it clears every structure in its path. Kansas recorded 377 bridge strikes in 2025, more than one every day. Measure the loaded rig, then route-check every bridge on the trip.

How long can a semitrailer be without a permit?

On the National Network, a semitrailer up to 48 ft long runs without a permit in every state. That is the federal floor in 23 CFR 658.13(b)(1): no state may impose a length limit of less than 48 ft on a semitrailer in a truck tractor-semitrailer combination. In practice the standard trailer is 53 ft long and a 53 ft semitrailer runs on the National Network in every state except Hawaii, where state law caps a semitrailer at 48 ft.

Above 53 ft the federal rule stops protecting the trailer and the 1982 grandfathered lengths take over. Appendix B to Part 658 lists the semitrailer length each state must still allow because it was in actual and lawful use there on December 1, 1982.

Louisiana and Oklahoma grandfather 59 ft 6 in, Texas grandfathers 59 ft, Arizona, Kansas and New Mexico grandfather 57 ft 6 in and Colorado and Wyoming grandfather 57 ft 4 in. Twenty-three states and the District of Columbia grandfather 48 ft only. The checker shows the grandfathered length for each state you pick when the trailer runs over 53 ft.

Grandfathering is a floor, not the current state ceiling. Current state law often allows more than the 1982 figure and the checker says so wherever it shows a grandfathered number. A trailer over 53 ft needs a check of the current state rule in each state on the route, or a permit. The Oversize Permit Cost Calculator prices the permit side of that decision.

Trailer length is only half the question for a 53 ft box. Each state also sets a kingpin-to-rear-axle limit that controls where the tandems may sit and sliding the tandems to fix the weight can break the kingpin rule. California allows 40 ft to the rearmost axle. Check the state rule in the Kingpin Law Checker before you roll and use the Axle Weight Rebalance Calculator when a tandem slide is needed for weight.

What is the 102-inch width rule?

Width is the one dimension where the federal rule is a hard number in both directions. Section 658.15(a) says no state may impose a width limit of more or less than 102 inches on a vehicle operating on the National Network. Hawaii is the single exception: it keeps a 108-inch width maximum under section 416(a) of the Surface Transportation Assistance Act. Special mobile equipment sits outside the rule entirely.

Measured width includes the load. A machine on a flatbed that sits inside the deck edges is legal width. The same machine with a bucket or track hanging past the side is an oversize load the moment it passes 102 inches. Measure the loaded rig at the widest point, not the trailer deck. Mirrors, turn signal lamps, handholds, splash and spray devices and load-induced tire bulge do not count and the exclusions section below lists the rest.

Past 102 inches, the route runs on permits. A state may grant a special use permit to a vehicle wider than 102 inches and each state on the route issues its own. Wide loads often need escort vehicles as well and the trigger points differ by state and by load width. The Escort and Pilot Car Requirements Checker covers the escort side. For Texas moves, the Texas Permit Wizard walks through that state permit process.

Can a truck be longer than 65 feet overall?

Yes. There is no federal overall length limit on a truck tractor-semitrailer combination or a truck tractor-semitrailer-trailer combination. Section 658.13(b)(3) bars states from imposing an overall length limit on either combination on the National Network. A sleeper tractor pulling a 53 ft trailer runs about 70 to 75 ft bumper to bumper and that rig is legal on the National Network in every state.

The 65 ft figure that people quote comes from other rules and mixing them up causes real trouble. Sixty-five feet is the overall limit for a traditional automobile transporter, for a maxi-cube vehicle and for grandfathered 28 ft 6 in twins. None of those figures applies to a standard tractor-semitrailer. The checker treats each configuration under its own rule, so the overall length field is optional for a tractor-semitrailer or doubles combination and required for the specialized equipment that carries an overall limit.

Off the National Network, states may set overall length limits of their own and local roads can be tighter still. Federal law guarantees reasonable access between the National Network and terminals and facilities for food, fuel, repair and rest, including one road-mile of access on the most reasonable and practicable route. Past that access, the state and local rules govern. Plan the first mile and the last mile with the same care as the Interstate miles.

What are the size rules for auto transporters?

An automobile transporter is specialized equipment and its limits sit in a different part of the rule from a standard trailer. A traditional automobile transporter, with the fifth wheel on the tractor frame over the rear axle, runs to 65 ft overall. A stinger-steered automobile transporter runs to 80 ft overall under the statute at 49 USC 31111(b)(1)(G), which the FAST Act set in 2015. The regulation at 23 CFR 658.13(e)(1)(i) still says 75 ft. The regulation is stale, the statute governs and the checker applies 80 ft.

Overhangs are part of the deal. The 80 ft protection covers a stinger-steered transporter with a front overhang under 4 ft and a rear overhang under 6 ft. The regulation requires states to allow at least 3 ft of front overhang and 4 ft of rear overhang on any automobile transporter. Extendable ramps, known as flippers, are excluded from the length measurement while they support vehicles and they must be retracted when they do not. Enter both overhangs and the checker tests each one.

An automobile transporter may also backhaul general freight, so long as it meets the weight limits for a truck tractor and semitrailer combination. That change came in the same 2015 FAST Act section that set the 80 ft limit. The backhaul rule matters for deadhead miles: a car hauler running home empty can legally carry freight on the return leg.

The other specialized combinations carry their own numbers. A boat transporter runs to 65 ft traditional and 75 ft stinger-steered under the regulation, with no statute bump to 80 ft. A drive-away saddlemount combination runs to 97 ft, with up to three saddlemounted vehicles plus one fullmount. A towaway trailer transporter combination runs to 82 ft, but only when the trailers are empty inventory property and the total weight stays at 26,000 lb or less.

A bus runs to 45 ft. A maxi-cube vehicle runs to 65 ft overall with 34 ft cargo boxes and 60 ft from the front of the first box to the rear of the second. The checker covers each configuration and the beverage semitrailer carries no overall limit at all.

What is the 41-foot kingpin myth?

There is no federal 41-foot kingpin rule. The 41 ft figure comes from 23 CFR 658.19(i), the reasonable-access rule. It says a state access review process may include a general provision allowing access, without a request, for commercial motor vehicles with semitrailers that have a kingpin distance of 41 ft or less. That is a rule about getting from the National Network to a terminal without filing a request. It is not a limit on where the tandems may sit and it never was.

The federal texts contain only three kingpin figures and none of them is a general limit. Section 658.13(g) and the statute behind it set 46 ft from the kingpin to the center of the rear axle for trailers used exclusively or primarily to transport vehicles for motorsports competition events. Appendix B carries three state footnotes: California allows a 53 ft semitrailer with a 38 ft kingpin-to-rearmost-axle distance, Indiana allows it at 40 ft 6 in and Wisconsin allows it at 41 ft measured to the center of the rear tandem assembly. Those footnotes are state-specific grandfathering, not a federal rule.

Kingpin limits are state law and they vary. California caps the distance at 40 ft to the rearmost axle on a 53 ft trailer and cities and counties there may restrict it further on specific routes. Florida allows 41 ft to the center of the rear axle or rear group of axles. Other states set no kingpin limit at all on the National Network.

Because the limit changes at the state line, the only safe check is state by state. Run the Kingpin Law Checker for the states on the route and remember that a tandem slide for weight changes the kingpin distance too. The Axle Weight Rebalance Calculator shows what a slide does to the axle weights.

What does not count toward truck length and width?

Section 658.16 lists the devices that do not count toward measured length or width and the list is narrower than most drivers expect. Rear view mirrors, turn signal lamps, handholds for cab entry and exit, splash and spray suppressant devices and load-induced tire bulge are excluded.

Non-property-carrying devices are excluded at the front of a semitrailer or trailer, when they extend no more than 3 inches beyond each side or the rear of the vehicle, or when they extend no more than 24 inches beyond the rear and are needed for loading or unloading. Devices listed in Appendix D to Part 658 are excluded as well.

Two more exclusions matter in practice. Resilient bumpers are excluded when they extend no more than 6 inches beyond the front or rear of the vehicle. Aerodynamic devices are excluded when they extend no more than 5 ft beyond the rear, provided they cannot damage a vehicle or injure a passenger in a vehicle that strikes the trailer from behind and provided they do not hide tail lamps, turn signals, marker lamps, identification lamps or other required safety devices such as placards or conspicuity markings.

Each exclusion is specific and cannot be combined with another. A bumper exclusion and an aerodynamic device exclusion do not stack into a longer allowance. Measurements run from a point on one side or end of the vehicle to the same point on the opposite side or end. Nothing in the list excludes the load itself, so cargo that sticks out past the trailer counts in full. Measure the loaded rig, then subtract only the listed devices.

How do state height limits differ?

State height limits fall into four groups. Twenty-seven states and the District of Columbia cap height at 13 ft 6 in. Twenty states allow 14 ft on the main truck network. Colorado and Nebraska allow 14 ft 6 in. Alaska allows 15 ft, the tallest legal height in the country. The 14 ft group runs mostly through the West and the Plains, with Arkansas, California, North Carolina, Oklahoma and Texas in the mix.

State law changes and height law changes with it. North Carolina raised its limit from 13 ft 6 in to 14 ft on December 1, 2023, under Session Law 2023-137. Older tables and older habits still show the old figure and the same staleness can hit any state. The checker carries the current figure for each state with the date it was verified and the last reviewed line at the top of this page shows when the table was last checked.

Height is the dimension where a route check matters most, because the legal limit and the real clearance are two different numbers. A state limit of 14 ft does not raise a bridge posted at 13 ft 6 in and a posted clearance below the rig height stops the move even where the height is legal. For the full state table with length and weight beside height, use the State Legal Limits Table. For a move that is over height in a state on the route, the Oversize Permit Cost Calculator prices the permit.

How do you use the Federal Size Limits Checker?

  1. Pick the configuration from the list: tractor-semitrailer, doubles, B-train, automobile or boat transporter, saddlemount, towaway, bus or maxi-cube.
  2. Enter the lengths for that configuration: the semitrailer length for a tractor-semitrailer, both trailer lengths for doubles, the overall length plus both overhangs for transporters.
  3. Enter the width in inches and the height in decimal feet, measured on the loaded rig at the widest and tallest points. A rig at 13 ft 6 in is 13.5.
  4. Pick up to three states on the route. The state picks set the height limit and, for a trailer over 53 ft, the grandfathered length.
  5. Read the verdict, the check table, the figures and the notes. A Check result names the rule to confirm. A Permit result names the dimension that needs a permit or a change.
  6. Copy the summary for the trip records, or reset the checker to start over.

Frequently asked questions

How long can a semitrailer be without a permit?

On the National Network, a semitrailer up to 48 ft long runs without a permit in every state and a 53 ft semitrailer runs in every state except Hawaii, where state law caps a semitrailer at 48 ft. Above 53 ft, the 1982 grandfathered lengths in Appendix B to 23 CFR Part 658 apply and current state law often allows more. Check the state rule in each state on the route, or get a permit.

Is there a federal height limit for trucks?

No. There is no federal height limit for commercial motor vehicles. Each state sets its own limit, from 13 ft 6 in in 27 states and the District of Columbia to 15 ft in Alaska. A rig at 13 ft 6 in or less is legal in every state. Legal height is not a clearance guarantee: the operator must still clear every bridge and structure on the route.

How wide can a truck be without a permit?

A truck may be 102 inches wide on the National Network without a permit and no state may set a limit of more or less than 102 inches. Hawaii allows 108 inches. Measured width includes the load, so cargo that sticks out past the trailer counts in full. Past 102 inches, each state on the route issues its own special use permit.

Is there a federal 41-foot kingpin rule?

No. The 41 ft figure comes from 23 CFR 658.19(i), the reasonable-access rule, which lets states allow access to terminals without a request for semitrailers with a kingpin distance of 41 ft or less. It is not a limit on where the tandems may sit. Kingpin limits are state law: California caps the distance at 40 ft to the rearmost axle and Florida allows 41 ft to the center of the rear axle or rear group of axles.

How long can an automobile transporter be?

A traditional automobile transporter runs to 65 ft overall. A stinger-steered automobile transporter runs to 80 ft overall under the statute at 49 USC 31111(b)(1)(G), with a front overhang under 4 ft and a rear overhang under 6 ft. The regulation at 23 CFR 658.13(e)(1)(i) still says 75 ft, but the regulation is stale and the statute governs. Boat transporters stay at 65 ft traditional and 75 ft stinger-steered.

Is a 53-foot trailer legal in every state?

On the National Network, yes, with one exception: Hawaii caps a semitrailer at 48 ft under HRS 291-34. Every other state allows a 53 ft semitrailer on the National Network. A 53 ft trailer must also meet each state kingpin-to-rear-axle limit, which controls where the tandems may sit. California allows 40 ft to the rearmost axle.

Related tools

Sources

Follow on WhatsApp Ask by Voice