California is the strictest kingpin state at 40 ft, measured to the rearmost axle. A tandem set to 41 ft at the tandem center reads 43 ft to the rearmost axle and is 3 ft over in California. Measure to the point each state uses.
Answer for one trailer and one route. Every answer updates as you change each field.
The trailer
The setback is the distance from the front of the trailer to the kingpin, usually 36 in. The spread is the distance between the two rear axles, usually 48 in. The setback drives the Tennessee rule and the tandem position entry.
The kingpin distance
Enter the distance directly, or pick the tandem position entry and let the checker work it out from the trailer length, the setback and the distance from the tandem to the rear. Say whether the reading was taken to the center of the rear tandem or to the rearmost axle. California and Indiana use the rearmost axle.
The route
Pick every state on the route. The Illinois highway class, the California road type and the Tennessee load type change the limit, so set them to match the trip. The motorsports box applies the 46 ft federal floor in every kingpin state.
Over the kingpin limit in 1 state
California is over by 3 ft 0 in. Slide the tandems forward 3 ft 0 in to meet the 40 ft 0 in California limit.
| State | Result | Detail |
|---|---|---|
| Arizona | No limit | No kingpin limit in the Arizona length statute (A.R.S. 28-1095). The 57 ft 6 in semitrailer cap carries no kingpin condition. |
| California | Over | 43 ft 0 in to the rearmost axle against a 40 ft 0 in limit (CVC 35401.5(a)(1)). Over by 3 ft 0 in. |
| Colorado | No limit | No kingpin limit in the Colorado length statute (C.R.S. 42-4-504). The 57 ft 4 in semitrailer cap carries no kingpin condition. |
| Illinois | Legal | 41 ft 0 in to the center of the rear tandem against a 45 ft 6 in limit (625 ILCS 5/15-107). Class I and II highways. |
| Indiana | Legal | 43 ft 0 in to the rearmost axle against a 43 ft 0 in limit (IC 9-20-13-4). |
| Kansas | No limit | No kingpin limit in the Kansas length statute (K.S.A. 8-1904). The 59 ft 6 in semitrailer cap carries no kingpin condition. |
| Missouri | No limit | No kingpin limit in the Missouri length statute (RSMo 304.170). The 53 ft semitrailer cap carries no kingpin condition. |
| Nevada | No limit | No kingpin limit in the Nevada length statute (NRS 484D.615). The 53 ft semitrailer cap carries no kingpin condition. |
| New York | Legal | 41 ft 0 in to the center of the rear tandem against a 43 ft 0 in limit (VTL 385(3)(e)). |
| Ohio | No limit | No kingpin limit in the Ohio length statute (ORC 5577.05). The 53 ft semitrailer cap carries no kingpin condition. |
| Pennsylvania | Legal | 41 ft 0 in to the center of the rear tandem against a 41 ft 0 in limit (75 Pa.C.S. 4923(b.1)(1)). |
| Utah | No limit | No kingpin limit in the Utah length statute (Utah Code 72-7-402). The 53 ft semitrailer cap carries no kingpin condition. |
The figures
| Figure | Value | Note |
|---|---|---|
| Kingpin to tandem center | 41 ft 0 in | As entered |
| Kingpin to rearmost axle | 43 ft 0 in | Tandem spread 48 in |
| Tightest limit on route | 40 ft 0 in | California |
| Slide forward to comply | 3 ft 0 in | California is the binding state |
| Tandem holes at 4 in spacing | 9 holes | Round up to the next hole |
| Tandem holes at 6 in spacing | 6 holes | Round up to the next hole |
What to do
- Slide the tandems forward 3 ft 0 in before you enter California. That is 9 holes at 4 in spacing or 6 holes at 6 in spacing.
- Re-check the axle weights after sliding. Moving the tandems forward shifts weight onto the trailer axles.
Notes
- California and Indiana measure to the rearmost axle. Every other kingpin state measures to the center of the rear axle or tandem. This checker converts your entry to each state measurement point.
- No federal kingpin limit applies to a standard 53 ft semitrailer. The 41 ft figure in 23 CFR 658.19(i) is a reasonable access rule for state access reviews, not a driver limit.
- California cities and counties may set a 38 ft limit on local roads (CVC 35401(e)). On state highways the limit is 40 ft for two or more axles and 38 ft for a single axle.
- Sliding the tandems to fix the kingpin distance changes the axle weights. Sliding forward loads the trailer axles. Run the new weights through the Axle Weight Rebalance Calculator before you drive.
This checker applies the kingpin limit in each state code to your answers. It is not legal advice. Confirm the kingpin distance with a tape measure before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice โ check the current regulation and your company policy before you rely on a result.
Quick answer: Twenty states set a kingpin to rear axle limit. California is the strictest at 40 ft for two or more axles and 38 ft for a single axle, measured to the rearmost axle. Thirty one jurisdictions set no kingpin limit at all. Enter the trailer length and the kingpin distance above and pick the states on the route. The checker gives a legal or over verdict for each state plus the slide distance to comply.
What is the kingpin law by state?
A kingpin law caps the distance from the kingpin to the rear axle of a semitrailer. The limit protects bridges and keeps long trailers tracking safely through turns. Twenty states set a limit. The rest set none, so a tandem position that is legal in Ohio can draw a citation the moment the trailer crosses into Pennsylvania.
The limits run from 40 ft to 45 ft 6 in. California sets 40 ft for two or more axles and 38 ft for a single axle. Illinois sets 45 ft 6 in on Class I and II highways and 42 ft 6 in on Class III and other state highways. Maine sets 45 ft 6 in.
Connecticut, Indiana, Minnesota, New York and Wisconsin set 43 ft. Alabama, Florida, Maryland, New Hampshire, New Jersey, North Carolina, Pennsylvania, Rhode Island, South Carolina, Tennessee, Vermont and Virginia set 41 ft. Tennessee sets 44 ft for a trailer without a tandem.
Most limits apply only to semitrailers over 48 ft. Indiana and Rhode Island apply their rule only over 48 ft 6 in. Alabama applies its rule only over 53 ft 6 in. South Carolina applies its rule to 53 ft trailers. Tennessee applies its rule only when the towed vehicle is over 48 ft from the kingpin. Pennsylvania and Vermont apply their rule to any trailer, whatever its length.
| State | Limit | Measured to | Applies when | Law |
|---|---|---|---|---|
| Alabama | 41 ft | Center of tandem or rearmost axle | Over 53 ft 6 in | Ala. Code 32-9-20 |
| California | 40 ft tandem, 38 ft single | Rearmost axle | Over 48 ft | CVC 35401.5(a)(1) |
| Connecticut | 43 ft | Center of rearmost axle | Over 48 ft | Conn. Gen. Stat. 14-262(c) |
| Florida | 41 ft | Center of rear axle or group | Over 48 ft | Fla. Stat. 316.515(3)(b) |
| Illinois | 45 ft 6 in Class I and II, 42 ft 6 in Class III | Center of rear axle | Over 48 ft | 625 ILCS 5/15-107 |
| Indiana | 43 ft | Rearmost axle | Over 48 ft 6 in | IC 9-20-13-4 |
| Maine | 45 ft 6 in | Center of rearmost axle | Over 48 ft | 29-A MRSA 2390(1)(J) |
| Maryland | 41 ft | Center of rear tandem | Over 48 ft | Md. Code, Transp. 24-104.2(c)(1) |
| Minnesota | 43 ft | Centerline of rear axle group | Over 48 ft | Minn. Stat. 169.81 subd. 2(b) |
| New Hampshire | 41 ft | Centerline of rear axle or tandem midpoint | Over 48 ft | RSA 266:11(II)(a) |
| New Jersey | 41 ft | Centerline of rear axle or group | Over 48 ft | N.J.S.A. 39:3-84(a)(4) |
| New York | 43 ft | Centerline of rear axle | Over 48 ft | VTL 385(3)(e) |
| North Carolina | 41 ft | Rearmost axle or tandem midpoint | Over 48 ft | N.C.G.S. 20-115.1(b)(2)(a) |
| Pennsylvania | 41 ft | Centerline of rear axle or group | Any trailer | 75 Pa.C.S. 4923(b.1)(1) |
| Rhode Island | 41 ft | Center of rear axle | Over 48 ft 6 in | R.I.G.L. 31-25-6(c) |
| South Carolina | 41 ft | Center of rear axle or tandem | 53 ft trailers | S.C. Code 56-5-4070(A)(1) |
| Tennessee | 41 ft tandem, 44 ft single | Tandem midpoint or rearmost axle | Over 48 ft from kingpin | Tenn. Code 55-7-201(c) |
| Vermont | 41 ft | Center of rearmost axle group | Any trailer | 23 V.S.A. 1432(a) |
| Virginia | 41 ft | Rearmost axle or tandem midpoint | Over 48 ft | Va. Code 46.2-1112 |
| Wisconsin | 43 ft | Tandem midpoint or center of rearmost axle | Over 48 ft | Wis. Stat. 348.07(2)(gr) |
Three details in the table catch drivers out. First, California and Indiana measure to the rearmost axle while every other kingpin state measures to the center of the rear axle or tandem. Second, Illinois changes its limit with the highway class, so a legal setting on an Interstate can be over on a state highway. Third, Tennessee exempts loads of livestock, motor vehicle parts and motor vehicles. It also measures the 48 ft threshold from the kingpin rather than from the front of the trailer.
Which states have no kingpin limit?
Thirty one jurisdictions set no kingpin to rear axle limit. They are Alaska, Arizona, Arkansas, Colorado, Delaware, the District of Columbia, Georgia, Hawaii, Idaho, Iowa, Kansas, Kentucky, Louisiana, Massachusetts, Michigan, Mississippi, Missouri, Montana, Nebraska, Nevada, New Mexico, North Dakota, Ohio, Oklahoma, Oregon, South Dakota, Texas, Utah, Washington, West Virginia and Wyoming. Each state caps the semitrailer length. None of those length laws carries a kingpin condition.
Three of these surprise drivers. Michigan had a kingpin wheelbase rule until 2018, when the state repealed it (2018 PA 35). Older tables still list a Michigan limit. Those tables are out of date. Georgia and Utah appear in some secondary tables with a 41 ft limit, but neither state code contains a kingpin rule. Ohio appears in one table at 45 ft 6 in, but the Ohio length statute sets no kingpin condition at all.
West Virginia needs a separate note. It sets no kingpin limit, but it allows a 53 ft semitrailer on the National Network only when the axle spacing from the rear axle of the tractor to the front axle of the semitrailer is 37 ft or less (W. Va. Code 17C-17-4(f)). That 37 ft figure is a tractor to trailer axle spacing rule, not a kingpin measurement. This checker never presents it as one.
A state with no kingpin limit can still stop a trailer for length. Hawaii caps semitrailers at 48 ft, so a 53 ft trailer is over the Hawaii length limit even though Hawaii sets no kingpin limit. The District of Columbia caps a semitrailer combination at 55 ft overall. Check the trailer length limit for each state on the route, not only the kingpin limit. The State Legal Limits Table lists the length, width and weight limit for every state.
How do you measure the kingpin to rear axle distance?
Measure from the center of the kingpin to the measurement point the state uses. California and Indiana use the rearmost axle. Every other kingpin state uses the center of the rear axle or the center of the tandem.
On a tandem with a 48 in spread, the rearmost axle sits 24 in behind the tandem center, so the two readings differ by 2 ft. A trailer that reads 41 ft to the tandem center reads 43 ft to the rearmost axle. That 2 ft gap is the most common reason drivers get a California citation they did not expect.
Measure with the trailer loaded and the tandems locked. Hook a tape at the center of the kingpin and run it straight back along the trailer centerline. Read it at the center of the rear axle or at the rearmost axle, whichever the state uses. Measure on level ground with the trailer brakes set. A tape pulled at an angle reads long. A reading taken with the tandems sliding reads whatever the tandems happen to be doing.
Tandem slider holes set the step size. Most sliders move the tandem 4 in per hole. Some move 6 in per hole. The checker reports the slide in feet and inches and in holes at both spacings, rounded up to the next hole. Sliding forward shortens the kingpin distance. Sliding back lengthens it.
If the kingpin distance is unknown, work it out from the tandem position. Take the trailer length and subtract the kingpin setback from the front of the trailer. Then subtract the distance from the center of the rear tandem to the rear of the trailer. On a 53 ft trailer with a 36 in setback and the tandem center 10 ft from the rear, the kingpin distance is 40 ft. The checker does this math when the tandem position entry is used.
Check the tire tread and pressure while the tape is out. The Tire Compliance Checker covers the federal tire rules for the same trailer.
What is the California kingpin law?
California sets the strictest kingpin limit in the country. A semitrailer over 48 ft may run up to 53 ft only when the kingpin to rearmost axle distance is 40 ft or less with two or more axles, or 38 ft or less with a single axle (CVC 35401.5(a)(1)). The measurement point is the rearmost axle, not the center of the tandem. A driver who sets the tandems to 40 ft at the tandem center is 2 ft over in California on a standard 48 in spread.
Cities and counties may set their own limit on local roads, down to 38 ft (CVC 35401(e)). A trailer that is legal on a state highway at 40 ft can be over on a city street in a locality that adopted the 38 ft limit. The checker flags this whenever California local roads are selected and the distance sits between 38 ft and 40 ft.
California also restricts 38 ft to 40 ft kingpin distances on local highways to places where the operator judges it safe (CVC 35401.1). The practical advice is simple. Set the tandems to 40 ft to the rearmost axle before entering California. Set them to 38 ft when the route runs on city or county roads.
The California rule is the reason most 53 ft trailers carry a 40 ft mark on the side. That mark is measured to the rearmost axle. Trust the tape rather than the mark when the trailer or the slider has been modified. A California citation written on a wrong measurement can be challenged through DataQs. The DataQs Challenge Helper walks through the challenge when the inspection record is wrong.
What is the federal kingpin rule?
There is no federal kingpin limit for a standard 53 ft semitrailer. No federal rule tells a driver what kingpin distance to run. The federal rules set a floor under state limits for one narrow class of trailer and set a process for access roads. Everything else is state law.
The one federal floor covers motorsports trailers. Federal law bars any state from setting a kingpin limit below 46 ft for a trailer used exclusively or primarily to transport vehicles for motorsports competition events (23 CFR 658.13(g)). Five states write the same 46 ft figure into their own law for motorsports trailers: Florida, Indiana, North Carolina, Pennsylvania and South Carolina.
The 41 ft figure that appears in many tables is not a federal kingpin limit. It comes from 23 CFR 658.19(i)(2)(i)(C), which tells states to run an access review process that may allow access without a request for semitrailers with a kingpin distance of 41 ft or less. That rule governs state access reviews, not drivers. It does not make 41 ft legal everywhere. California still limits the same trailer to 40 ft.
Older federal tables add to the confusion. The footnotes to 23 CFR Part 658 Appendix B still list grandfathered figures of 38 ft for California, 40 ft 6 in for Indiana and 41 ft for Wisconsin. Those figures are grandfathering history. The current state statutes set 40 ft for California, 43 ft for Indiana and 43 ft for Wisconsin. The current statute governs. This checker uses the current state code for every state.
How far do you slide the tandems to fix a kingpin violation?
Slide the tandems forward by the overage. If the kingpin distance is 43 ft to the rearmost axle and the California limit is 40 ft, slide forward 3 ft. The checker reports the slide for the tightest state on the route, so one slide fixes every state on the route at once.
Convert the slide to holes before touching the slider. Divide the slide in inches by the hole spacing and round up to the next hole. A 3 ft slide is 9 holes at 4 in spacing or 6 holes at 6 in spacing. Rounding up matters: 8 holes at 4 in spacing moves the tandem only 32 in, which leaves the trailer 4 in over.
Check the slider travel before sliding. Some trailers run out of rail before the tandem reaches the legal position. A trailer that cannot reach the limit cannot run legally in that state at that kingpin setting. Measure again after sliding and confirm the new reading against the limit. A hole count is a plan. The tape is the proof.
Plan the slide before the state line. The legal place to slide is a rest area or a truck stop, not the shoulder past the sign. The checker result can be copied to the clipboard for the log or for dispatch. A slider that will not move is a pre-trip failure. The Pre-Trip Inspection Checklist covers the slider, the tires and the brakes before the wheels turn.
Does sliding the tandems change the axle weights?
Yes. Sliding the tandems forward shifts weight onto the trailer axles and off the drive axles. Sliding back does the reverse. A slide that fixes a kingpin violation can push a trailer axle group over the 34,000 lb tandem limit.
A slide that fixes a weight problem can push the kingpin distance over the state limit. The two problems trade against each other. California is where the trade bites hardest because its kingpin limit is the strictest.
Re-weigh or re-calculate after every slide. The Axle Weight Rebalance Calculator works out the new axle weights from the slide distance, so the kingpin fix and the weight fix can be checked together. Never assume a slide that fixes one problem leaves the other alone.
When the kingpin limit and the weight limit cannot both be met, the load has to move or the route has to change. Shifting freight forward or back inside the trailer changes the weight split without touching the tandems. A different route through states with a longer kingpin limit can also solve it. The Federal Size Limits Checker and the State Legal Limits Table give the length and weight limits for the same combination.
How do you use the Kingpin Law Checker?
- Enter the trailer length in feet and the kingpin setback in inches. The setback is the distance from the front of the trailer to the kingpin, usually 36 in.
- Pick the rear axle setup and the tandem spread in inches. The spread is the distance between the two rear axles, usually 48 in.
- Enter the kingpin distance directly, or pick the tandem position entry and enter the distance from the center of the rear tandem to the rear of the trailer.
- Pick the states on the route. The Illinois highway class, the California road type and the Tennessee load type change the limit, so set them to match the trip.
- Read the verdict for each state. A state marked Over shows how far over it is. The figures below show the slide distance and the hole count.
- Copy the summary for the log or for dispatch. Re-check the axle weights after sliding with the Axle Weight Rebalance Calculator.
Frequently asked questions
What is the kingpin law in California?
California limits the kingpin to rearmost axle distance to 40 ft for two or more axles and 38 ft for a single axle (CVC 35401.5(a)(1)). The limit applies to semitrailers over 48 ft. Cities and counties may set a 38 ft limit on local roads (CVC 35401(e)).
Which states have a kingpin law?
Twenty states set a kingpin limit: Alabama, California, Connecticut, Florida, Illinois, Indiana, Maine, Maryland, Minnesota, New Hampshire, New Jersey, New York, North Carolina, Pennsylvania, Rhode Island, South Carolina, Tennessee, Vermont, Virginia and Wisconsin. The other thirty one jurisdictions set no kingpin limit.
Is there a federal kingpin law?
No. There is no federal kingpin limit for a standard 53 ft semitrailer. Federal law only bars states from setting a limit below 46 ft for motorsports trailers (23 CFR 658.13(g)). The 41 ft figure in 23 CFR 658.19(i) is a reasonable access rule for state access reviews, not a driver limit.
How is the kingpin distance measured?
Measure from the center of the kingpin to the center of the rear axle or tandem, except in California and Indiana, which measure to the rearmost axle. On a tandem with a 48 in spread, the rearmost axle sits 2 ft behind the tandem center, so the two readings differ by 2 ft.
How many holes do I slide the tandems to fix a kingpin violation?
Divide the overage in inches by the hole spacing and round up to the next hole. A 3 ft overage is 9 holes at 4 in spacing or 6 holes at 6 in spacing. The checker reports the hole count for the tightest state on the route.
Does Michigan have a kingpin law?
No. Michigan repealed its kingpin wheelbase rule in 2018 (2018 PA 35). Older tables that list a Michigan kingpin limit are out of date. Michigan caps semitrailers at 53 ft with no kingpin condition.
Related tools
- Axle Weight Rebalance Calculator: rebalance the axle weights after sliding the tandems.
- Federal Size Limits Checker: check the federal length, width and weight limits for the same combination.
- State Legal Limits Table: see every state length, width and weight limit in one table.
- Pre-Trip Inspection Checklist: check every tire, wheel and brake item before the wheels turn.
- Tire Compliance Checker: check tire tread depth and pressure before the same trip.
- DataQs Challenge Helper: challenge a roadside inspection record when the measurement was wrong.
- Trucking Tools: browse every free calculator on Trucking Mind.
Sources
- 23 CFR 658.13, Length. Motorsports kingpin floor of 46 ft. law.cornell.edu/cfr/text/23/658.13 Accessed November 19, 2026.
- 23 CFR Part 658, Appendix B, Grandfathered Semitrailer Lengths. law.cornell.edu/cfr/text/23/part-658/appendix-B Accessed November 19, 2026.
- 23 CFR 658.19, Reasonable Access. law.cornell.edu/cfr/text/23/658.19 Accessed November 19, 2026.
- California Department of Transportation, Vehicle Lengths. dot.ca.gov/programs/traffic-operations/legal-truck-access/vehicle-lengths Accessed November 19, 2026.
- California Vehicle Code 35401.5, Semitrailer Length and Kingpin Distance. Accessed November 19, 2026.
- Indiana Code 9-20-13-4, Semitrailer Length and Kingpin Distance. Accessed November 19, 2026.
- Wisconsin Statutes 348.07, Length of Vehicles. Accessed November 19, 2026.
- Maine Revised Statutes Annotated, Title 29-A, Section 2390, Length of Vehicles. Accessed November 19, 2026.
- Michigan Public Act 35 of 2018, Repeal of the Kingpin Wheelbase Rule. Accessed November 19, 2026.
- Arkansas Code 27-35-208, Length of Vehicles. law.justia.com/codes/arkansas/title-27/subtitle-3/chapter-35/subchapter-2/section-27-35-208 Accessed November 19, 2026.