Enter the cargo and tare weight of each pup, then your scale weights for every axle group. The result shows the pup split, the gross weight check, the axle checks and the bridge checks.
Your pups
Pup tare defaults to 8,000 lb and dolly tare to 3,000 lb. Change any box to match your own rig.
A single-axle dolly is standard on most doubles. A tandem dolly adds a second axle and a second tandem check.
Your scale weights (optional)
Scale every axle group, including the dolly. Leave the boxes blank to check gross weight only.
Axle spacings
Defaults suit a standard doubles rig with two 28 ft pups. Measure your own rig for an exact bridge check.
Rate (optional)
Rate and diesel price are your numbers: the tool carries no rate or fuel figure of its own.
Enter your pups to see the split.
Scale the dolly too
A converter dolly adds an axle most drivers forget to scale. Weigh every group, including the dolly, before you trust a legal gross weight.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not professional advice — verify figures from official sources before acting on them. Scale every axle group, including the dolly, before you roll: a legal gross weight can hide an overweight group.
Quick answer: Enter each pup cargo and tare weight to see the split, the gross weight and every axle group check. The example loads 24,000 lb in the lead pup and 18,000 lb in the rear pup: the lead pup grosses 32,000 lb, the rear pup 26,000 lb, for a rig gross of 79,000 lb with 1,000 lb to spare.
How the pup split works
A standard doubles rig runs a tractor, a lead pup, a converter dolly and a rear pup: 8 axles with a single-axle dolly or 9 with a tandem dolly. The tool adds cargo plus tare for each pup, then adds the tractor and the dolly to reach the gross weight.
The example loads 24,000 lb of cargo in the lead pup and 18,000 lb in the rear pup, with each pup taring 8,000 lb. The lead pup grosses 32,000 lb and the rear pup 26,000 lb, so the lead pup carries 55.2 percent of the 58,000 lb of pup weight.
With an 18,000 lb tractor and a 3,000 lb dolly, the rig grosses 79,000 lb, leaving 1,000 lb under the 80,000 lb limit. The 42,000 lb of cargo sits inside the typical 40,000 to 44,000 lb payload band for standard doubles.
A Silver Eagle single-axle dolly weighs 2,680 lb, while a Max-Atlas tandem dolly tares 4,982 lb. The tool defaults dolly tare to 3,000 lb: change it to match your own dolly.
Put the heavier pup in front: Alaska and Indiana both write the rule into their LCV permits. A heavy rear pup makes the back trailer sway, so the tool warns you when the rear pup outweighs the lead pup.
Axle groups and the bridge formula
Gross weight is only half the check. Each axle group has its own limit: 20,000 lb for a single axle and 34,000 lb for a tandem under 23 CFR 658.17.
The bridge formula then caps groups of axles by their spacing. W equals 500 times the bracket of L times N over N minus 1, plus 12N, plus 36.
W is the weight in pounds. L is the distance in feet between the first and last axle of the group. N is the number of axles in the group.
The example scale ticket reads steer 11,000 lb, drives 21,400 lb, lead tandem 17,600 lb, dolly 14,700 lb and rear tandem 14,300 lb. The five groups add to 79,000 lb, matching the gross weight.
Drives plus lead tandem total 39,000 lb against a 59,500 lb bridge limit over 26 ft. Lead tandem plus dolly plus rear tandem total 46,600 lb against a 71,000 lb limit over 37 ft. The whole rig at 70 ft with 8 axles is capped by the 80,000 lb gross limit.
The tool checks the steer axle against a 12,000 lb practical ceiling from tire and axle ratings. Federal law allows 20,000 lb on the steer axle, but most steer tires and axles are rated well below that. Two consecutive tandems may each carry 34,000 lb when the first to last axle distance is 36 ft or more.

The Bridge Formula Axle Weight Checker linked below runs the same formula on any axle group with your own spacings.
The LCV freeze: doubles are free, triples are frozen
Standard doubles are legal on the National Network in every state. Under 23 CFR 658.23 a tractor with two trailers may run on the Network when each cargo unit is 28.5 ft or less. That carve-out is why two 28 ft pups are the standard doubles rig.
Longer combination vehicles are frozen in place. The 1991 ISTEA law barred states from opening new LCV routes, so triples and over-80,000 lb doubles may run only where they ran on 1 June 1991. No state has added a triples route since.

Seventeen states allow triples today, all grandfathered under the freeze. The table below lists them with their cargo length and gross weight limits, as published in 23 CFR Part 658 Appendix C. Check the state permit office before you roll: routes, seasons and driver rules vary.
| State | Length | Max gross | Notes |
|---|---|---|---|
| Alaska | 110 ft | State law governs | May 1 to Sep 30 only. 10 yrs AK experience. |
| Arizona | 95 ft | 123,000 lb | 129,000 lb on I-15. |
| Colorado | 115.5 ft | 110,000 lb | |
| Idaho | 95 ft | 105,500 lb | |
| Indiana | 104.5 ft | 127,400 lb | Toll Road only. |
| Iowa | 100 ft | 129,000 lb | Sioux City only. |
| Kansas | 109 ft | 120,000 lb | Turnpike plus permit routes. |
| Missouri | 109 ft | 120,000 lb | 90,000 lb from Oklahoma. 20-mile band from the state line. |
| Montana | 100 ft | 131,060 lb | |
| Nebraska | 95 ft | Empty only | Must travel empty. I-80 Wyoming to Exit 440. |
| Nevada | 95 ft | 129,000 lb | |
| North Dakota | 100 ft | 105,500 lb | |
| Ohio | 95 ft | 115,000 lb | Turnpike only. Triples 90 to 105 ft overall. |
| Oklahoma | 95 ft | 90,000 lb | |
| Oregon | 96 ft | 105,500 lb | |
| South Dakota | 100 ft | 129,000 lb | |
| Utah | 95 ft | 129,000 lb |
Source: 23 CFR Part 658 Appendix C, as published in the CFR-2025 edition. Figures checked 17 Nov 2026.
Seven more states allow heavier doubles without triples. Washington allows 105,500 lb doubles, Wyoming 117,000 lb, New York 143,000 lb, Massachusetts 127,400 lb, Michigan 164,000 lb, New Mexico 86,400 lb and Pennsylvania 100,000 lb.
Florida, Mississippi and Hawaii run tandem trailers under state law, with no federal weight cap in Appendix C.
License: Class A plus the T endorsement
Doubles work needs a Class A CDL with a T endorsement. A combination vehicle with a gross combination weight rating of 26,001 lb or more, with the towed unit over 10,000 lb, is a Group A vehicle under 49 CFR 383.91(a)(1). A standard doubles rig clears both numbers.

The T endorsement covers double and triple trailers under 49 CFR 383.93(b)(1). It needs a knowledge test only, with no skills test, under 49 CFR 383.93(c)(1). The endorsement code T appears on the license under 49 CFR 383.153(a)(9)(i).


What the rate math covers
Enter your loaded miles, deadhead miles, rate per loaded mile, diesel price and MPG to see the money side of the run. The tool shows gross revenue, fuel cost, net per loaded mile, net per total mile and the deadhead share of your miles.
As an example only, take 600 loaded miles plus 80 deadhead miles at a $3.25 rate, $4.75 diesel and 7.0 MPG. The load grosses $1,950.00 and burns 97.1 gallons of fuel for $461.43, leaving $1,488.57 after fuel: $2.48 per loaded mile and $2.19 per total mile, with deadhead at 11.8 percent of miles.
The tool carries no rate or diesel figure of its own: both are your numbers. Fuel is the only cost it counts, so add maintenance, insurance and fixed costs to find your true cost per mile.
How to use this calculator
Six steps and one result. No account and no email needed.
- Enter the cargo and tare weight of each pup, plus the dolly and tractor tares.
- Choose 1 or 2 dolly axles to match your converter dolly.
- Enter your scale weights for every axle group, including the dolly.
- Check the spacings against your own rig, or keep the standard defaults.
- Read the verdict: the pup split, the axle checks and the bridge checks.
- Enter your miles, rate, diesel price and MPG to see the rate math.
Doubles calculator questions
How many axles does a doubles rig have?
A standard doubles rig has 8 axles: 3 on the tractor, 2 on the lead pup tandem, 1 on the converter dolly and 2 on the rear pup tandem. A tandem dolly adds a ninth axle, for 9 axles in total. The tool lets you choose 1 or 2 dolly axles to match your rig.
Which pup should be heavier?
The lead pup should be heavier. Alaska and Indiana both require the heavier trailer in front on their LCV permits. A heavy rear pup makes the back trailer sway, so the tool warns you when the rear pup outweighs the lead pup.
Do I need a special endorsement to pull doubles?
Yes. You need a Class A CDL with a T endorsement for double and triple trailers. The T endorsement needs a knowledge test only, with no skills test, under 49 CFR 383.93.
Can I run doubles in any state?
Standard doubles with two 28.5 ft pups or shorter may run on the National Network in every state. Triples are different: only 17 states allow them, all grandfathered under the 1991 LCV freeze. Over-80,000 lb doubles need a state permit and run only on grandfathered routes.
Why does the tool ask for my scale weights?
Cargo weights alone cannot tell you what each axle carries. The tool checks each axle group and the bridge formula from the scale weights you enter. Weigh every group, including the dolly, before you trust a legal gross weight.
What is the bridge formula?
The bridge formula caps the weight on a group of axles by the distance between the first and last axle. W equals 500 times the bracket of L times N over N minus 1, plus 12N, plus 36, where W is the weight in pounds. Spread your axles further apart to carry more weight on the group.
Related tools and guides
- Tanker Load Calculator: work out tanker load weight, axle weights and the most you can legally load
- Step Deck Fit Calculator: check freight fit on both step deck levels plus payload
- Bridge Formula Axle Weight Checker: check any axle group against the bridge formula with your own spacings
- Hotshot Axle Weight Checker: check a hotshot load against ratings based axle limits
- Cost Per Mile Calculator: put maintenance and repair costs beside fuel and insurance in your full cost per mile
- All Trucking Mind tools: free calculators and checkers for drivers and carriers
This calculator follows the weight limits in 23 CFR 658.17, the LCV rules in 23 CFR 658.23 and the endorsement rules in 49 CFR 383.93. It is guidance only.
Weight limits and size rules change. Confirm your figures with the current rule text before you rely on a single number.
Your inputs stay in your browser. Nothing is sent to our servers.