Skip to main content

Trucking Mind

This checker answers one question: can this load legally be permitted? It runs the nondivisible test in 23 CFR 658.5 against your answers, then checks the statutory categories, the emergency relief route, plus grandfather rights. A load that fails every route is divisible, which means it must be split into legal loads. No standard overweight or oversize permit exists for it.

Answer each question for the load as it stands on the trailer. Every answer updates the result as you change each field. All weights are in pounds. All times are in work-hours.

The load

The federal gross cap on the Interstate is 80,000 pounds. A load can also exceed a length limit, an axle limit, or a bridge formula limit while the gross weight stays under the cap. Answer the first question yes when any limit is exceeded.

The three prong test, 23 CFR 658.5(1)

Only one prong has to pass. More than 8 work-hours to dismantle makes the load nondivisible on its own. Exactly 8 work-hours does not pass. The applicant bears the burden of proof on the number of work-hours, so a written estimate matters.

Special categories

The precast concrete panel rule is written for Colorado only. The milk rule applies everywhere. The emergency response, cask, plus military categories are discretionary: the state may treat them as nondivisible, but it is not required to.

Emergency relief, 23 USC 127(i)

The emergency permit route needs a major disaster declaration, not an emergency declaration. The permit expires not later than 120 days after the declaration date. The clock runs from the declaration, not from the permit application.

Grandfather rights

Grandfather rights cover weights that were legal under state law on July 1, 1956, plus axle group weights legal on January 4, 1975. They are specific to a weight on a route. If you are unsure, ask the state permit office before assuming either way.

Verdict: Divisible. Split the load into legal loads.

1 check passed, 4 checks failed, 4 not applicable.

The load fails the nondivisible test in 23 CFR 658.5(1): splitting it would not compromise its intended use, destroy its value, or take more than 8 work-hours. No statutory category applies. No discretionary category applies. No emergency window is open. No grandfather right applies. A standard overweight or oversize permit is not available for a divisible load. Split it into legal loads.

The checks

RequirementResultDetail
Over a legal length or weight limitYesThe load exceeds a legal limit, so the divisibility question decides whether a permit is possible. Gross weight entered: 90,000 lb.
Intended use, 23 CFR 658.5(1)(i)NoSplitting the load would not compromise its intended use. This prong does not help the permit.
Value, 23 CFR 658.5(1)(ii)NoSplitting the load would not destroy its value. This prong does not help the permit.
Dismantle time, 23 CFR 658.5(1)(iii)NoDismantling takes 2.0 work-hours, within the 8 work-hour line. This prong does not help the permit.
Burden of proof on hours, 23 CFR 658.5(1)(iii)N/AThe hours test is not relied on, so no proof of hours is needed for this application.
Statutory category, 23 USC 127(a)(6) and 127(a)(13)N/AThe load is not fluid milk products and is not a Colorado precast concrete panel vehicle, so no statutory category applies.
Discretionary category, 23 CFR 658.5(2)N/AThe load is not an emergency response vehicle, a spent nuclear fuel cask, or a marked military vehicle, so no discretionary category applies.
Emergency relief, 23 USC 127(i)N/AThe load is not relief supplies for a declared major disaster, so the emergency permit route does not apply.
Grandfather or congressional authorizationNoNo grandfather right or specific congressional authorization covers this load. Outside those rights, a divisible load cannot be permitted overweight.

The figures

FigureValueNote
Gross weight entered90,000 lbThe gross vehicle weight you entered for this move.
Federal gross cap, Interstate80,000 lb23 USC 127(a)(2) plus 23 CFR 658.17(b). The bridge formula can set a lower cap for a short axle group.
Amount over the cap10,000 lb overThe gross weight above the 80,000 lb federal cap. Axle and bridge formula limits still apply.
Dismantle time2.0 work-hoursWork-hours to dismantle the load using appropriate equipment. More than 8 work-hours makes the load nondivisible.
Against the 8 work-hour line6.0 work-hours under the lineThe load does not pass prong (iii) on hours alone.

What to do

  • Split the load into legal loads. Work out how many legal loads it takes: divide the gross weight by the legal limit for the axle group.
  • Do not apply for a standard overweight permit for this load. The state cannot issue one for a divisible load outside the exceptions in this checker.
  • If the shipper insists the load cannot be split, ask for the reason in writing and re-run this checker with the corrected answers.

Before you apply for the permit

  • Keep the permit plus the route sheet plus any escort or signing conditions in the cab for the whole move.
  • Keep the evidence behind the verdict in the file: the shipper statement on use and value, the dismantle hours estimate, or the disaster declaration.
  • Keep this summary in the file with the load papers, so the next dispatcher can see why the load was permitted or split.

Notes

  • The divisibility test applies to a load or vehicle exceeding applicable length or weight limits. A legal load never reaches the test.
  • Only one prong has to pass. A load that passes on intended use alone is nondivisible, even when it could be dismantled in an hour.
  • The 8 work-hour line is strict: more than 8 work-hours. Exactly 8 work-hours does not pass.
  • A nondivisible verdict is not a permit. The State issues the permit plus sets the route. It may attach escort, signing, plus travel time conditions.
  • Divisible-load permits outside the emergency rule exist only through grandfather rights or a specific congressional authorization for a commodity or a route.

This tool applies 23 CFR 658.5 plus 23 USC 127 to your inputs. Confirm the result against the regulation text plus the state permit office before acting. An answer given wrong gives a wrong verdict, so check any answer that sits close to a line.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool applies the published text of 23 CFR 658.5 plus 23 USC 127 to your answers, not legal advice — confirm the result with the state permit office or your legal counsel before moving an overweight or oversize load.

Quick answer: A load over a legal length or weight limit can be permitted only when it is nondivisible. Under 23 CFR 658.5, a load is nondivisible when separating it would compromise its intended use, destroy its value, or take more than 8 work-hours to dismantle using appropriate equipment. Only one of the three tests has to pass. Congress also treats fluid milk products plus Colorado precast concrete panels as nondivisible by statute. A divisible load cannot get a standard overweight permit: it must be split into legal loads, unless an emergency relief permit, a grandfather right, or a specific congressional authorization covers it.

Last reviewed: · Focus keyword: divisible vs non-divisible load

What is a nondivisible load under federal law?

A nondivisible load is a load or vehicle over a legal length or weight limit that cannot be broken into smaller legal loads without ruining it. The definition sits in 23 CFR 658.5, the definitions section of the federal size and weight rules. It gives three separate tests. A load passes when separating it into smaller loads or vehicles would compromise its intended use, destroy its value, or require more than 8 work-hours to dismantle using appropriate equipment. Only one test has to pass. A load that passes on intended use alone is nondivisible, even when it could be dismantled in an hour.

The first test asks about function. The regulation explains it as making the vehicle unable to perform the function for which it was intended. A wind turbine blade cut in half cannot generate power. A bridge beam cut in half cannot span the gap. A transformer split open cannot step voltage down. The question is not whether the pieces could be moved separately. It is whether the thing still does its job after the split. When the answer is no, the load is nondivisible.

The second test asks about value. The regulation explains it as making the load or vehicle unusable for its intended purpose. The two tests overlap in practice, but they are not identical. A load can keep some scrap value after being cut apart while losing all of its working value. The test looks at value for the intended purpose, not at salvage value. A pre-stressed concrete girder sawn into sections keeps the value of its concrete plus steel, but it loses the value of a girder. It fails the value test.

The third test asks about time. When dismantling takes more than 8 work-hours using appropriate equipment, the load is nondivisible even when the parts would still work plus keep their value. The time test covers the machine that comes apart cleanly but slowly: a large press, a drilling rig, a piece of process equipment with hundreds of bolted connections. The applicant bears the burden of proof on the number of work-hours, so the hours claim needs evidence behind it.

The definition only matters once a load exceeds a limit. A load within legal length plus weight never reaches the test. The federal gross cap on the Interstate is 80,000 pounds under 23 USC 127(a)(2), with a single axle limit of 20,000 pounds plus a tandem axle limit of 34,000 pounds, plus the bridge formula setting the cap for each axle group. The Federal Size Limits Checker works out the federal length plus weight limits for a given combination. The Kingpin Law Checker covers the state kingpin to rear axle limits, which are a separate length test that varies by state.

The payoff for passing the test is a permit. Section 658.17(h) states that states may issue special permits without regard to the axle, gross, or Federal Bridge Formula requirements for nondivisible vehicles or loads. That sentence is the whole legal basis for the oversize and overweight permit system. Without it, no state could let an 80,000 pound plus load onto the Interstate. The permit still comes from the state, not from the federal government. The state sets the route, the travel times, plus any escort or signing conditions. The federal rule only opens the door.

One common misunderstanding is worth clearing up early. Nondivisible does not mean large. A 90,000 pound load of gravel is large plus heavy, but it is divisible: a loader can split it into two legal loads in minutes, with no loss of use or value. A 50,000 pound yacht on a trailer is lighter, but it is nondivisible: cutting it in half destroys it. Size is not the test. Separability is the test.

What is the 8 work-hour rule for oversize permits?

The 8 work-hour rule is the third prong of the nondivisible test. Section 658.5(1)(iii) treats a load as nondivisible when separating it would require more than 8 work-hours to dismantle using appropriate equipment. The line is strict: more than 8. Exactly 8 work-hours does not pass. A dismantle estimate of 8 hours plus 15 minutes passes. A dismantle estimate of 7 hours plus 59 minutes does not. The checker applies the line exactly that way.

Work-hours means labor time, not clock time. Two mechanics working 5 hours each on the same dismantle produce 10 work-hours, even though only 5 hours pass on the clock. The regulation does not spell out the crew size, so the honest reading is the total labor the job takes with the crew the job needs. A one person job that takes 9 hours passes. A four person job that takes 2 hours of clock time with 8 work-hours of labor does not pass, because the total is exactly 8. Keep the crew size plus the hours per person in the estimate, so the permit office can see the arithmetic.

Appropriate equipment is part of the test. The hours are measured with the equipment the job calls for, not with hand tools when a crane is the right tool. A state permit office will not accept an inflated estimate built on slow methods. The estimate should name the equipment: the crane capacity, the forklift, the torch set, the torque wrenches. A manufacturer teardown procedure is the strongest evidence, because it states the steps plus the time for each step with the specified tools.

The burden of proof sits on the applicant. The regulation says so in plain words: the applicant for a nondivisible load permit has the burden of proof as to the number of work-hours required to dismantle the load. The permit office does not have to disprove the claim. The applicant has to prove it. A bare number on the application form is weak evidence. A written estimate from the manufacturer, a prior teardown work log, or a signed statement from the rigging contractor is strong evidence. The checker asks whether the hours can be documented. It flags the gap when they cannot.

What counts as dismantling time is narrower than most applicants think. It covers taking the load apart into pieces that can travel legally. It does not cover loading time, securing time, or travel time. It does not cover reassembly at the far end, though a reassembly estimate can support the dismantle estimate when the two jobs mirror each other. It does not cover waiting for a crane to arrive. The honest figure is the wrench time with the right crew plus the right equipment.

LoadDismantle time, typicalPasses the hours test
Excavator, counterweight plus boom removed3 to 5 work-hoursNo, under the line
Large press, bolted frame plus hydraulics12 to 20 work-hoursYes, over the line
Drilling rig mast, pinned sections10 to 16 work-hoursYes, over the line
Modular building, single wide section4 to 6 work-hoursNo, under the line
Industrial boiler, refractory plus casing20 to 40 work-hoursYes, over the line

The table shows typical ranges, not legal findings. Every load is judged on its own dismantle procedure. A press with quick release couplings can come apart in 6 hours. A modular building with welded connections can take 12. The figure that matters is the one for the actual load, with the actual crew, plus the actual equipment. When the estimate sits close to the line, measure it twice: a permit granted on 9 hours can be challenged at the scale when the inspector sees a load that comes apart in 6.

A load that passes the hours test does not need to pass the other two tests. That is the point of the three prong structure. A machine that dismantles into working parts, each keeping its value, is still nondivisible when the dismantle takes more than 8 work-hours. The time test exists for exactly that load. Use it when the use test plus the value test both fail.

Can you get a permit for a divisible load?

As a general rule, no. A standard oversize or overweight permit is available only for a nondivisible load. Section 658.17(h) authorizes special permits for nondivisible vehicles or loads. It authorizes nothing for divisible ones. A state that issues an overweight permit for a load of gravel, lumber, or palletized freight has no federal basis for it on the Interstate. The load must be split into legal loads. That is the plain answer. It surprises drivers who assume a permit can cover any overweight move.

The rule exists for a reason. The weight limits protect bridges plus pavement. Every overweight trip shortens the life of the road it runs on. Congress accepted that cost only for loads that cannot be divided, because those loads have no other way to move. A divisible load has another way: split it. The permit system is not a way to buy the right to run heavy. It is a way to move the loads that cannot be made legal any other way.

Three exceptions break the general rule. The first is the emergency relief permit under 23 USC 127(i), which covers divisible loads delivering relief supplies after a Presidential major disaster declaration, for up to 120 days. The second is grandfather rights, which preserve weights that were legal under state law on July 1, 1956, plus axle group weights legal on January 4, 1975. The third is a specific congressional authorization for a commodity or a route, such as the Louisiana sugarcane permit or the Idaho plus North Dakota 129,000 pound allowances. Outside those three exceptions, a divisible load has no permit route on the Interstate.

Before splitting, check whether the load is really over. A load that looks heavy may be legal with the axles set right. The Axle Weight Rebalance Calculator works out how shifting the load or the tandems changes the axle weights. A load over on one axle group can become legal by moving freight forward or back, without removing a single pound. The State Legal Limits Table lists the legal limits by state, because a load legal in one state can be over in the next. The permit question follows the strictest state on the route.

When the load is genuinely over plus genuinely divisible, the split is the answer. Work out how many legal loads it takes. A 120,000 pound load at an 80,000 pound cap needs two trips. A 170,000 pound load needs three. The arithmetic is simple, but the planning is not: each legal load needs its own trailer, its own driver, plus its own schedule. The cost of the extra trips is the cost of the weight limit. It is cheaper than the fine plus the offload at the scale.

One more option exists for some loads: a different trailer. A load over the bridge formula on a short axle group can become legal on a longer spread, because the formula allows more weight as the axle spacing grows. A load over on a tandem can become legal on a tridem. The trailer change does not make the load nondivisible. It makes the load legal, which removes the permit question entirely. The Federal Size Limits Checker shows the federal limits the new combination must meet.

State practice varies on non-Interstate roads. The federal limits in section 127 bind the Interstate System. State highways follow state law, which can be more generous for some commodities. A divisible load that cannot run overweight on the Interstate may be able to run overweight on a state route under a state permit. That is a state question, not a federal one. The answer changes by state plus by commodity. The checker answers the federal question. The state permit office answers the state question.

Which loads does Congress treat as nondivisible by statute?

Congress has written two loads into the nondivisible category by statute, so they never need the three prong test. The first is fluid milk products. Section 127(a)(13) states that a vehicle carrying fluid milk products shall be considered a load that cannot be easily dismantled or divided. The second is Colorado precast concrete panels. Section 127(a)(6) states that, with respect to the State of Colorado, vehicles designed to carry 2 or more precast concrete panels shall be considered a nondivisible load. In each case the statute settles the question. The permit office does not ask whether the milk could be split into two tankers. The statute says it cannot be easily divided. That ends the inquiry.

The milk rule applies everywhere. A milk tanker over the weight limit in any state is a nondivisible load under federal law. The state may issue a special permit for it. The rule covers fluid milk products: raw milk, pasteurized milk, cream, plus other liquid dairy products moving in bulk. It does not cover packaged dairy products on pallets, which are divisible freight like any other palletized load. The distinction is the liquid bulk form, which cannot be split without a second tanker plus a transfer operation.

The concrete panel rule applies in Colorado only. The statute names the state. A vehicle designed to carry 2 or more precast concrete panels is nondivisible in Colorado. The same vehicle crossing into Kansas, Nebraska, or Utah loses the statutory category at the state line. Outside Colorado the panels must pass the three prong test like any other load. In practice a precast panel usually passes the use test or the value test anyway, since a panel cut in half is not a panel. The Colorado statute removes the argument in the home state.

Congress has also written a set of commodity plus route authorizations that work like exceptions to the divisible load rule. These are not nondivisible findings. They are specific permissions for specific loads on specific roads. Louisiana may allow, by special permit, vehicles up to 100,000 pounds hauling sugarcane during the harvest season, for not more than 100 days each year. New Hampshire may allow a 6 axle truck-tractor plus dump trailer combination up to 99,000 pounds on Interstate Routes 89, 93, plus 95. Idaho plus North Dakota may allow vehicles up to 129,000 pounds that meet the axle plus bridge formula limits and are authorized under state law. Wisconsin may allow logging vehicles up to 98,000 pounds on a short segment of Interstate Route 39. Minnesota may allow logging vehicles up to 99,000 pounds on a short segment of Interstate Route 35.

AuthorizationCommodity or vehicleLimit
23 USC 127(a)(9), LouisianaSugarcane, harvest season100,000 lb, 100 days a year
23 USC 127(a)(10), New Hampshire6 axle dump trailer combination99,000 lb, I-89, I-93, I-95
23 USC 127(o), WisconsinLogging vehicles, I-3998,000 lb, 6 axles or more
23 USC 127(q), MinnesotaLogging vehicles, I-3599,000 lb, 6 axles or more
23 USC 127(t), IdahoVehicles authorized under state law129,000 lb
23 USC 127(u), North DakotaVehicles authorized under state law129,000 lb

The table shows a sample, not the full list. Section 127 carries more than twenty such provisions, covering Maine, Vermont, Mississippi, West Virginia, Kentucky, Texas, Arkansas, North Carolina, plus others. Each one is narrow: a named commodity, a named route, a named weight. None of them is a general right to run heavy. A carrier hauling sugarcane in Louisiana cannot use the Louisiana provision in Texas. A carrier hauling logs in Wisconsin cannot use the Wisconsin provision on a different segment of Interstate Route 39.

The checker treats these authorizations as a single question: does a grandfather right or a specific congressional authorization cover this commodity or route? A yes answer does not grant the permit. It points the carrier to the state permit office with the specific authorization in hand. The permit office confirms the provision, checks the route, plus issues the permit on the terms the statute sets.

Which vehicles may a state treat as nondivisible?

Section 658.5(2) gives states a discretionary power over three kinds of vehicle. A state may treat as nondivisible loads or vehicles: emergency response vehicles, casks designed for the transport of spent nuclear materials, plus military vehicles transporting marked military equipment or materiel. The word is may. The state is not required to treat any of them as nondivisible. The state decides. A carrier moving one of these vehicles must confirm the treatment with the state permit office before counting on it.

The emergency response vehicle category is narrower than the name suggests. The regulation describes vehicles loaded with salt, sand, chemicals or a combination thereof, with or without a plow or blade attached in front, used for the purpose of spreading the material on highways that are or may become slick or icy. The picture is a winter maintenance truck: a spreader truck loaded with salt, running ahead of a storm, with a plow on the front. The category covers that vehicle. It is not a blanket category for every vehicle with emergency lights. A fire truck or an ambulance is an emergency vehicle in ordinary language, but the regulation text points at the spreading operation. The checker asks the question in the broader form, then leaves the state decision to the state.

Emergency vehicles also have a separate protection in the statute. Section 127(r) states that a state shall not enforce against an emergency vehicle a vehicle weight limit, up to a maximum gross vehicle weight of 86,000 pounds, of less than 24,000 pounds on a single steering axle, 33,500 pounds on a single drive axle, 62,000 pounds on a tandem axle, or 52,000 pounds on a tandem rear drive steer axle. The subsection defines an emergency vehicle as a vehicle designed to be used under emergency conditions to transport personnel plus equipment, plus to support the suppression of fires plus the mitigation of other hazardous situations. This is a floor, not a permit: the state may not enforce a lower limit against such a vehicle. It is a different provision from the discretionary treatment in section 658.5(2). Do not confuse the two.

The spent nuclear fuel cask category covers the heavy shielded casks that carry used reactor fuel. A loaded cask is a single indivisible object by design: the shielding is the container. The container cannot be split. The category exists so that states can permit the move without forcing the carrier through the three prong test on a load that obviously passes it. Cask moves also carry security plus routing conditions that go far beyond an ordinary oversize permit.

The military category covers military vehicles transporting marked military equipment or materiel. The marking matters: the equipment must be marked as military equipment or materiel. An unmarked commercial truck hauling military freight under a defense contract is not automatically in the category. A military vehicle moving marked equipment is. The category covers the movement of tanks, armored vehicles, artillery, plus other heavy equipment that cannot be broken down for transport.

All three categories share one feature: the state decides. A state that declines to treat a vehicle as nondivisible leaves the carrier with the three prong test. Most of these vehicles pass that test anyway. A fire truck cannot be split without destroying its use. A cask cannot be split at all. A tank cannot be split without destroying its value. The discretionary category is a shortcut, not the only route. When the state says no, run the three prong test before giving up on the permit.

What are emergency divisible-load permits?

Section 127(i) is the one route that lets a divisible load run overweight on the Interstate. It is narrow, temporary, plus tied to disaster relief. A state may issue special permits during an emergency to overweight vehicles plus loads that can easily be dismantled or divided, when three conditions are all met. The President must have declared the emergency to be a major disaster under the Robert T. Stafford Disaster Relief and Emergency Assistance Act. The permits must be issued in accordance with state law. The permits must be issued exclusively to vehicles plus loads that are delivering relief supplies. All three conditions must hold at the same time. A missing condition closes the route.

The first condition is the one most people get wrong. It needs a major disaster declaration, not an emergency declaration. The Stafford Act gives the President two different declaration powers. An emergency declaration under section 501 covers a smaller event with limited federal help. A major disaster declaration under section 401 covers a larger event with full federal help. Section 127(i)(1)(A) names the major disaster declaration. An emergency declaration alone does not open the permit route. The distinction matters in practice, because the President issues emergency declarations far more often than major disaster declarations.

The second condition is state law. The federal statute permits the state to issue the permits. It does not require the state to issue them. It does not issue them itself. The state permit office runs the program under its own law, with its own application form, its own route review, plus its own conditions. A carrier seeking an emergency permit applies to the state, not to FEMA or to the Federal Highway Administration.

The third condition limits the permits to relief supplies. The statute says exclusively. A truck hauling bottled water, food, medicine, generators, or building materials into the disaster area qualifies. A truck hauling ordinary commercial freight through the disaster area does not qualify, even when the freight is urgently needed. The load must be relief supplies. The carrier should be ready to prove it: a bill of lading naming the relief cargo, a letter from the relief organization, or a FEMA mission assignment.

The permit expires not later than 120 days after the date of the declaration. The clock runs from the declaration date, not from the permit issue date. A permit issued on day 119 expires on day 120. A carrier that applies late gets a short permit. The checker works out the remaining window from the days since the declaration, so the carrier can see how much time is left before applying. When the window has closed, the divisible load goes back to the general rule: split it into legal loads.

The emergency permit route is separate from the hours of service emergency relief exemption. That exemption, in 49 CFR 390.23, relieves drivers from parts of the hours rules during a declared emergency. It does not change the weight limits. A driver can be exempt from the hours rules plus still overweight. The two exemptions answer different questions. A carrier needs each one separately.

What are grandfather rights for overweight loads?

Grandfather rights preserve weight limits that were legal before the federal limits took effect. Section 127(a)(2) lets a state keep the maximum weights permitted for vehicles using its public highways under laws or regulations in effect on July 1, 1956. Section 658.17(i) states the same rule in regulation form: the axle plus gross weight provisions do not apply to weights legally authorized under state law on July 1, 1956. The axle group requirement does not apply to vehicles legally grandfathered under state groups of axles tables or formulas on January 4, 1975. The rights are vested on the dates Congress named. They remain available to a state even when the state adopts a lower limit for a time.

The dates matter. July 1, 1956 is the date the Interstate System was authorized. A state that allowed 90,000 pound gross weights on its highways on that date may still allow them on the Interstate. January 4, 1975 is the date of the Federal-Aid Highway Amendments of 1974, which set the bridge formula. A state with an axle group table or formula in effect on that date may still use it. The two dates cover different things: the 1956 date covers axle plus gross weights, while the 1975 date covers axle group weights.

Grandfather rights are specific. They cover a weight on a route, not a general right to run heavy. A state that allowed 90,000 pounds on a particular highway in 1956 can allow 90,000 pounds on that highway now. It cannot use the 1956 law to allow 90,000 pounds on a highway that carried a lower limit in 1956. The right follows the old law, road by road, weight by weight. A carrier claiming a grandfather right needs to know the old state law for the exact route.

In practice, grandfather rights matter most in a handful of states with generous pre-1956 weight laws. Michigan is the best known example: its 1956 laws allowed heavy multi-axle combinations. The state still allows them under the grandfather clause, with its own axle weight table. Other states carry narrower rights, covering a single commodity or a single corridor. Most states have no grandfather right above the federal limits, because their 1956 laws matched or fell below the federal figures.

The longer combination vehicle freeze works on a similar idea with a different date. Under section 127(d), a longer combination vehicle may operate only when the configuration was authorized by state law plus in actual lawful operation on or before June 1, 1991. The freeze preserves the LCV operations that existed in 1991 and bars new ones. The LCV Training Requirement Checker covers the driver training rule for longer combination vehicles. The freeze is not a grandfather right in the weight sense, but it shows the same congressional habit: preserve what existed, bar what did not.

How do you find out whether a grandfather right covers a load? Ask the state permit office. The old state laws are public records, but they are hard to read without the state code as it stood in 1956. The permit office knows which rights its state holds. The checker treats the question as a yes, no, or unsure answer. An unsure answer is honest: most carriers do not know the 1956 law for their route. The permit office does.

How do you prove a load is nondivisible?

Proof starts with the prong. A load that passes on intended use needs a statement from the shipper or the manufacturer explaining what the load does plus why splitting it breaks the function. A load that passes on value needs a statement explaining what the load is worth whole plus what the parts are worth after a split. A load that passes on hours needs a written dismantle estimate with the crew size, the hours per person, plus the equipment. Each prong has its own evidence. The permit application should name the prong plus attach the matching evidence.

The manufacturer is the best source for the use test plus the hours test. The manufacturer designed the load, knows how it works, plus knows how it comes apart. A teardown procedure from the manufacturer manual, with the steps plus the time for each step, is the strongest hours evidence available. A letter from the manufacturer stating that the load cannot be divided without destroying its function is the strongest use evidence available. Ask for both before the move is scheduled, because a manufacturer letter can take days to arrive.

The shipper is the best source for the value test. The shipper knows the purchase price, the replacement cost, plus the resale value of the parts. A written statement from the shipper giving the whole value plus the parts value, with the arithmetic shown, answers the value question directly. A statement that says only that the load is valuable is weak. A statement that says the load is worth 400,000 dollars whole plus 30,000 dollars in parts is strong.

Photographs help every prong. A photo of the load on the trailer shows the size plus the shape. A photo of the connection points shows how the load comes apart. A photo of the manufacturer plate shows the model plus the serial number, which lets the permit office look up the specifications. Keep the photos in the file with the written statements. A permit application with photos plus a written estimate is far stronger than a bare form.

The permit application itself goes to the state permit office, not to a federal agency. There is no federal oversize permit issuer. Each state runs its own program, with its own form, its own fee, plus its own processing time. The Permit Type Finder works out which permit family fits the move: single trip, multi-trip, annual, or superload. The Permit Lead-Time Checker works out how far ahead to apply, based on the load class plus the state. Apply early: a superload permit can take weeks. A denied application takes longer.

Expect conditions on the permit. The state may set the route, restrict travel to daylight hours, require escort vehicles, require oversize signs plus flags, or ban travel on weekends plus holidays. The Escort and Pilot Car Checker works out whether the move needs an escort in each state on the route. The Oversize Sign and Flag Checker covers the signing rules. The Oversize Curfew and Holiday Checker covers the travel time limits. Read every condition on the permit before moving. A violated condition voids the permit, which leaves the load overweight without a permit.

What happens if you haul a divisible load overweight without a permit?

The first stop is the scale. A divisible load over the limit without a permit is an overweight violation, found at the first weigh station or portable scale on the route. The officer weighs the combination, compares it against the legal limits plus any permit in hand, then cites the violation. The citation names the excess weight plus the statute. The driver cannot fix it by promising to split the load at the next town. The violation is complete the moment the overweight vehicle uses the highway.

The fine follows the state schedule. Overweight fines vary widely by state: some states charge a few cents per pound over the limit, others charge a flat amount plus a per pound rate that rises with the excess. A small excess costs a small fine. A large excess costs a large fine, plus the fine grows fast once the excess passes the state thresholds. The FMCSA Fine Calculator works out the current federal penalty for a given violation. The state fine is separate from any federal penalty. The two can stack.

The officer can also order the load offloaded or the vehicle held until the excess weight is removed. An offload order at a scale means finding a second truck, transferring freight at the roadside, plus paying for the extra handling. A hold order means the truck sits until the problem is fixed. Either outcome costs more than the split would have cost at the origin. The Superload Threshold Checker shows when a load crosses into superload territory in each state, where the permit conditions plus the enforcement attention both increase.

The violation also lands on the carrier record. An overweight citation counts in the Safety Measurement System under the Vehicle Maintenance BASIC, where it joins every other vehicle violation. A single overweight citation will not sink a carrier record, but a pattern of weight violations draws FMCSA attention plus raises the carrier score. A high score brings more inspections, which find more violations. The cycle starts with one overweight trip.

The driver faces consequences too. An overweight citation goes on the driver record in most states. A driver with a pattern of weight violations is a hiring risk for the next carrier. A driver who knowingly hauls a divisible load overweight without a permit, after the dispatcher told them to split it, has a harder conversation at the next job interview than a driver who refused the load.

The fix is simple. It is the point of this checker. Split the load before it leaves the yard. The split costs a second trip. The fine plus the offload plus the record cost more. Run the checker on every load that looks heavy, before the truck rolls, not after the scale light turns red.

How do you use the Divisible-Load Checker?

Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the verdict change.

  1. Answer whether the load exceeds a legal length or weight limit, then enter the gross vehicle weight.
  2. Answer the three prong questions: intended use, value, plus dismantle hours.
  3. Say whether the dismantle hours can be documented with a written estimate.
  4. Pick any special category that fits, plus say whether the move is in Colorado.
  5. Answer the emergency relief questions when the load carries relief supplies.
  6. Read the verdict plus the per-check table, then follow the action list.

Use answers from the load, not from habit. A load that looks like last week load may differ in one detail that changes the verdict. A dismantle estimate from the manufacturer beats a guess from memory. A shipper statement on value beats an assumption. The checker is only as good as the answers behind it.

Read the figures table before the action list. It shows the gross weight against the 80,000 pound cap, the dismantle hours against the 8 work-hour line, plus the emergency window when one applies. The figures show which line the load sits closest to, even when the verdict is clear. A load that passes the hours test by 15 minutes is a different risk from a load that passes by 10 hours.

Questions drivers ask

What is a nondivisible load?

A load or vehicle over a legal length or weight limit that cannot be separated into smaller loads without compromising its intended use, destroying its value, or taking more than 8 work-hours to dismantle using appropriate equipment. The definition is in 23 CFR 658.5. Only one of the three tests has to pass.

Can I get a permit for a divisible load?

As a general rule, no. A standard overweight or oversize permit is available only for a nondivisible load. The exceptions are emergency relief permits under 23 USC 127(i), grandfather rights for weights legal in 1956, plus specific congressional authorizations for a commodity or a route. Outside those exceptions, a divisible load must be split into legal loads.

What is the 8 hour rule for oversize permits?

When dismantling a load takes more than 8 work-hours using appropriate equipment, the load is nondivisible under 23 CFR 658.5(1)(iii), even when the parts would still work plus keep their value. Exactly 8 work-hours does not pass. The applicant bears the burden of proof on the number of work-hours.

Is a load of milk nondivisible?

Yes. Under 23 USC 127(a)(13), a vehicle carrying fluid milk products is considered a load that cannot be easily dismantled or divided. The statute settles it, so no prong test is needed. The rule covers fluid milk products in bulk, not packaged dairy products on pallets.

How long does an emergency divisible-load permit last?

Not longer than 120 days after the date of the Presidential major disaster declaration under the Stafford Act. The clock runs from the declaration date, not from the permit issue date. A permit issued on day 119 expires on day 120.

Do I still need a state permit when the load is nondivisible?

Yes. A nondivisible verdict is not a permit. The state issues the permit, sets the route, plus may attach escort, signing, plus travel time conditions. There is no federal oversize permit issuer. Apply to the permit office in each state on the route.

Related tools

Sources

  • 23 CFR 658.5, Definitions (eCFR, read verbatim Nov 19, 2026; nondivisible load or vehicle, origin 49 FR 23315, June 5, 1984)
  • 23 CFR 658.17, Weight (eCFR, read verbatim Nov 19, 2026; 80,000 pound cap at paragraph (b), special permits for nondivisible loads at paragraph (h), grandfather rights at paragraph (i))
  • 23 USC 127, Vehicle weight limitations, Interstate System (Cornell LII, read verbatim Nov 19, 2026; 80,000 pound cap at (a)(2), Colorado panels at (a)(6), milk at (a)(13), emergency permits at (i), emergency vehicles at (r))
Follow on WhatsApp Ask by Voice