One scale ticket, two slides. This calculator works out how far to slide the trailer tandems or the fifth wheel to legalize axle weights. Sliding never fixes an overweight gross. Reweigh after every slide.
Enter the weights from the scale ticket once. Both tabs use the same ticket.
Your scale ticket
Copy the three weights from a certified scale ticket. The federal Interstate limits are 20,000 lb on a single axle, 34,000 lb on a tandem axle group and 80,000 lb gross.
Tandem slide settings
Enter the kingpin distance for the physics formula. Leave it blank and the calculator falls back to the rule of thumb. Measure the distance with a tape from the kingpin to the center of the rear axle group.
Slide the tandems forward 3 holes
The drive tandem is 800 lb over the 34,000 lb limit. Moving the tandems forward 3 holes shifts about 810 lb from the drives to the trailer tandems. Projected weights after the slide: drives 33,990 lb and trailer tandems 33,210 lb. Both groups land under the 34,000 lb limit.
| Check | Result | Detail |
|---|---|---|
| Gross weight | Pass | 78,200 lb. Under the 80,000 lb federal limit. |
| Drive tandem | Fail | 34,800 lb. Over the 34,000 lb tandem limit by 800 lb. |
| Trailer tandem | Pass | 32,400 lb. Under the 34,000 lb tandem limit. |
| Steer axle | Pass | 11,000 lb. Under the 20,000 lb federal single axle limit and inside the usual 12,000 to 12,500 lb planning range. |
| Slide plan | Pass | Slide forward 3 holes. Each hole moves about 270 lb. |
| Kingpin distance | Pass | 39 ft after the slide. Under the 40 ft California cap. Other states set their own limits, so check every state on the route. |
The figures
| Figure | Value | Note |
|---|---|---|
| Weight shifted per hole | 270 lb | Physics formula: trailer weight times hole spacing divided by kingpin distance |
| Holes to slide | 3 holes forward | Round up: a partial hole is not a setting |
| Projected drive weight | 33,990 lb | At or under the 34,000 lb limit |
| Projected trailer weight | 33,210 lb | At or under the 34,000 lb limit |
| Projected kingpin distance | 39 ft | California cap 40 ft |
| Gross weight | 78,200 lb | Under the 80,000 lb limit |
What to do
- Reweigh the rig after sliding. The per-hole figure is an estimate and the scale ticket is the only proof.
- Lock the slider pins and check that they seat fully before you roll.
- Check the new kingpin distance against every state on the route before you roll. California caps it at 40 ft.
Notes
- A tandem slide moves weight between the drive axles and the trailer axles only. In the real world a small amount also moves to or from the steer axle, which is one more reason to reweigh.
- The per-hole figure comes from the physics formula using your trailer weight, hole spacing and kingpin distance. It shifts slightly as weight moves, so treat it as an estimate.
- Sliding the tandems changes the kingpin to rear axle distance. A slide that fixes the weights can break a state kingpin limit.
Check the new kingpin distance for every state on your route with the Kingpin Law Checker.
This calculator applies 23 CFR 658.17 to your answers. It is not legal advice. Confirm the weights on a certified scale before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice โ check the current regulation and your company policy before you rely on a result.
Quick answer: A tandem slide moves weight between the drive axles and the trailer axles. Slide the tandems forward for heavy drives and back for heavy trailer tandems. Each hole moves about 250 lb at 4 in spacing and about 400 lb at 6 in spacing, but the true figure comes from the physics formula: trailer axle weight times hole spacing divided by the kingpin to rear axle distance. A fifth wheel slide moves weight between the steer axle and the drives at about 250 to 500 lb per notch. No slide fixes an overweight gross. Reweigh after every slide.
How many holes do you slide the tandems to fix overweight axles?
Take the overage on the heavy group and divide it by the weight moved per hole. Round up to the next whole hole. A partial hole is not a setting on the slider rail. The calculator does this division for you and checks that the other group has room for the weight that moves across.
A scale ticket shows drives at 34,800 lb and trailer tandems at 32,400 lb. The drives are 800 lb over the 34,000 lb limit. The trailer carries 32,400 lb on 4 in hole spacing at a 40 ft kingpin distance, so each hole moves 32,400 times 4 divided by 480, which is 270 lb. Divide 800 by 270 to get 2.96, then round up to 3 holes forward. After the slide the drives sit near 33,990 lb and the trailer tandems near 33,210 lb. Both groups land under the limit.
The same ticket can also be fixed from the fifth wheel tab when the steer axle has room. The drives are 800 lb over and the steer axle sits at 11,000 lb against a 12,000 lb limit. Two notches forward move about 1,000 lb from the drives to the steer axle. The steer lands at 12,000 lb and the drives at 33,800 lb. Two fixes exist for one ticket. The tandem slide is the usual first choice because it leaves the steer axle alone.
Some tickets have no slide fix. When both axle groups are over the limit, the two groups together carry more than 68,000 lb and no distribution between them can legalize both. When the gross weight is over 80,000 lb, no slide of any kind helps. The calculator says so plainly instead of inventing a hole count.
How much weight does one tandem hole move?
There is no fixed number. The weight moved per hole depends on how much weight already sits on the trailer axles, on the hole spacing of the slider rail and on the kingpin to rear axle distance. The physics formula is: weight shifted per hole equals the trailer axle weight times the hole spacing divided by the kingpin to rear axle distance. Use the same units on both sides: hole spacing in inches and kingpin distance in inches.
The table below works the formula at a 40 ft kingpin distance, which is the California cap and a common working setting for a 53 ft van. A light trailer moves far less per hole than a maxed-out trailer. Half the load means half the movement per hole.
| Weight on trailer tandems | 4 in hole spacing | 6 in hole spacing |
|---|---|---|
| 12,000 lb (light load) | 100 lb per hole | 150 lb per hole |
| 20,000 lb | 167 lb per hole | 250 lb per hole |
| 30,000 lb | 250 lb per hole | 375 lb per hole |
| 34,000 lb (maxed out) | 283 lb per hole | 425 lb per hole |
The rule of thumb comes from this table. At 4 in spacing the figure sits near 250 lb per hole on a well loaded trailer. At 6 in spacing it sits near 400 lb per hole. The rule is a starting point, not a measurement. A driver who learned 400 lb on a maxed-out van and applies it to a partial load slides about twice as far as needed.
The calculator uses the physics formula whenever you enter the kingpin distance. Leave that field blank and it falls back to the rule of thumb: 250 lb per hole at 4 in spacing and 400 lb per hole at 6 in spacing. Enter the kingpin distance for the better number. Measure it once with a tape and write it on the bulkhead.
A shorter kingpin distance moves more weight per hole. The lever arm is shorter, so each inch of slide carries more of the load. A trailer set at 36 ft moves about 300 lb per hole where the same trailer at 40 ft moves 270 lb. Hole spacing is a property of the trailer: measure it once and stop guessing.
Which way do you slide the tandems?
Slide toward the problem: drives heavy means tandems forward, trailer heavy means tandems back. The kingpin is the pivot for the whole trailer. The load creates a turning force about that pivot. The trailer axle group carries that force divided by its distance from the kingpin. Move the axle group and you change the split.
Sliding the tandems forward shortens the lever arm. The trailer axles pick up more of the load and the drives lighten. Sliding the tandems back lengthens the lever arm. The trailer axles carry less and the drives pick up the difference. The same amount of weight moves in both directions: what leaves one group lands on the other.
The rule feels backward in the cab because the tractor is what physically moves. You pull forward to slide the tandems back relative to the trailer. You back up to slide them forward. The tandem assembly sits still on the pavement while the trailer frame slides over it. Think about where the axles end up on the trailer, not about which pedal you pressed.
Set the trailer brakes before you move. Pull both slider pins, move slowly, then check that both pins seat fully in the rail holes before you roll. A pin that is only partly in holds at idle and walks out under load. Pull on each pin by hand. Never get under the trailer during the slide.
Can sliding the tandems fix an overweight gross?
No. Sliding moves weight between axle groups. It never removes weight from the rig. A gross weight over 80,000 lb stays over 80,000 lb after any slide. The only fixes are to remove freight, reload the trailer or get an overweight permit. The federal gross limit comes from 23 CFR 658.17(b), while the bridge formula can set a lower gross limit on a short wheelbase.
The bridge formula is the second test that catches drivers out. The formula caps the weight on any group of axles by the distance between its outer axles: W equals 500 times the bracket L times N divided by N minus 1, plus 12N, plus 36. W is the maximum weight in pounds, L is the distance in feet between the outer axles of the group and N is the number of axles in the group. The result is rounded to the nearest 500 lb.
Sliding the tandems forward shrinks the distance between the drives and the trailer tandems, which lowers the weight the formula allows across that group. A rig can pass the axle scales and still fail bridge. The Bridge Formula Axle Weight Checker runs this test for any axle group before you roll.
The Federal Highway Administration gives a five axle example that shows the trap. The rig totals 80,000 lb with 12,000 lb on the steer axle and 34,000 lb on each tandem. The four axle group from the drives through the trailer tandems weighs 68,000 lb across 35 ft, where the formula allows only 65,500 lb. The rig is legal on every axle and illegal on the bridge.
Two consecutive tandem sets spaced 36 ft or more apart may each carry 34,000 lb under 23 USC 127(a)(2). That exception helps doubles and spread axle setups. It does not help a standard five axle van with an overweight gross. Check the gross first, then the groups, then the bridge formula.
What is the kingpin limit and why does a tandem slide break it?
Many states cap the distance from the trailer kingpin to the center of the rear axle group. The limit controls the wheelbase and the turning radius of the combination. California caps it at 40 ft on a two axle semitrailer under California Vehicle Code 35400. Other states set their own figures. A position that is legal in one state can be illegal two states later.
Every tandem slide changes this distance. Sliding back lengthens it. A slide that fixes the weights can push the kingpin distance past a state limit and earn a citation at the next scale. The calculator shows the new kingpin distance after every slide and flags it when it passes 40 ft. The figure is a warning, not a clearance: states set their own limits.
Check the new distance against every state on the route before you roll. The Kingpin Law Checker lists the limit for each state. The Federal Size Limits Checker covers the federal length rules that sit behind the state limits. The State Legal Limits Table puts the size and weight limits for all 50 states and DC in one place.
There is no federal 41 ft kingpin rule. The 41 ft figure comes from 23 CFR 658.19(i), the reasonable access provision. Semitrailers with a kingpin distance of 41 ft or less get general access without a request. That is an access rule, not a kingpin limit. The federal figures that let a 53 ft semitrailer run without a permit sit in 23 CFR 658.13.
How does a fifth wheel slide move weight?
The fifth wheel is the coupling plate on the tractor that the trailer kingpin locks into. On most tractors it sits on rails and slides fore and aft in notches. Sliding it forward moves weight from the drives onto the steer axle. Sliding it back moves weight from the steer axle onto the drives. The trailer axle weight does not change at all.
Each notch shifts about 250 to 500 lb between the steer axle and the drives. The exact figure depends on the tractor wheelbase, the notch spacing and the load distribution. A common rule is about 100 lb per inch of slide. The calculator lets you enter your own per-notch figure: use 500 lb when you do not know it, then reweigh and adjust the figure to match what the scale shows.
A scale ticket shows the steer axle at 12,600 lb and the drives at 33,000 lb. The steer limit is 12,000 lb from the axle rating, so the steer is 600 lb over. Two notches back at 500 lb per notch move about 1,000 lb from the steer to the drives. The steer lands at 11,600 lb and the drives at 34,000 lb, exactly at the tandem limit. The same ticket also shows the steer 250 lb over the combined tire rating of 12,350 lb, which is the more urgent number: the rubber fails first.
Use the fifth wheel for fine tuning after the tandems have done the heavy work. The tandem slide moves weight between the drives and the trailer in steps of about 250 to 400 lb per hole. The fifth wheel then trims the steer to drive split in steps of about 500 lb per notch. Never trade a drive axle violation for an overloaded steer axle, tire or front axle rating.
What is the steer axle weight limit?
There is no separate federal steer axle limit. The steer axle is a single axle, so the 20,000 lb single axle ceiling in 23 CFR 658.17(c) applies to it. In practice the steer axle is limited far below that by the equipment on it. The legal steer weight is the lowest of three numbers: the federal or state single axle limit, the steer axle rating on the door sticker and the combined load rating of the two steer tires.
The tire rating usually binds first. A standard 295/75R22.5 Load Range G steer tire is rated 6,175 lb, so two of them allow 12,350 lb on the axle. Many door stickers show a steer axle rating of 12,000 to 12,350 lb. That is why 12,000 lb is the planning number most drivers use, even though the federal ceiling is 20,000 lb. A steer axle at 13,100 lb on tires rated 12,350 lb together is over the rubber, even when it is under every other limit.
Federal Highway Administration guidance sets the floor for state enforcement: states may not limit steering axle weights to less than 20,000 lb or the axle rating set by the manufacturer, whichever is lower. The same guidance bars states from limiting tire loads to less than 500 lb per inch of tire width, except on steering axle tires. Some states also limit weight per inch of tire width on their own roads, so the state limit can bind below the tire rating.
The calculator works out the steer limit from the three numbers and names the one that binds. Enter the per-tire rating from the sidewall and the axle rating from the door sticker. Leave either blank to skip that check. The Tire Compliance Checker runs a full check on one tire, including tread depth, defects, load and cold pressure.
Why must you reweigh after every slide?
Every slide figure on this page is an estimate. The physics formula uses the trailer weight, the hole spacing and the kingpin distance, but the true shift also depends on where the load sits inside the trailer, on the fifth wheel position and on the fuel level. A load with weight near the front bulkhead transfers more per hole than a load spread evenly along the floor. The formula gives a starting point, not a guarantee.
The per-hole figure also shifts as weight moves. The formula uses the trailer weight before the slide. After three holes forward, the trailer carries more weight than it did before, so the fourth hole would move slightly more than the third. The calculator uses the starting weight for the whole slide. The difference is small on a short slide and grows on a long one.
A tandem slide also moves a small amount of weight to or from the steer axle in the real world. The calculator holds the steer axle steady, which matches the standard industry method. The steer shift is small, but it is one more reason the scale ticket after the slide is the only proof that counts. A reweigh fee is trivial next to an overweight citation.
Overweight fines vary by state and by how far over the limit the axle sits. The FMCSA Fine Calculator shows the maximum federal civil penalty for a weight violation. A citation also lands on the carrier record. The Pre-Trip Inspection Checklist covers the axle and suspension items a driver checks before the wheels turn.
How do you use the Axle Weight Rebalance Calculator?
- Weigh the rig on a certified scale and copy the steer, drive and trailer weights from the ticket into the three boxes at the top.
- Pick the Tandem Slide tab for a heavy drive or trailer tandem. Enter the hole spacing from the slider rail and the kingpin distance when you know it.
- Read the holes and the direction, then check the projected weights and the new kingpin distance in the figures table.
- Pick the Fifth Wheel Slide tab for a heavy steer axle or heavy drives. Enter the steer tire rating, the axle rating and the weight shifted per notch.
- Read the notches and the direction, then check the projected steer and drive weights and the tire rating row.
- Make the slide, lock the pins or jaws, then reweigh before you leave the scale. Copy the summary for the trip records, or reset the calculator to start over.
Frequently asked questions
How many holes do you slide the tandems to fix overweight drives?
Divide the overage by the weight moved per hole and round up. A drive tandem 800 lb over with 270 lb per hole needs 3 holes forward. The weight per hole comes from the physics formula: trailer axle weight times hole spacing divided by the kingpin to rear axle distance. At 4 in spacing the rule of thumb is about 250 lb per hole. Reweigh after sliding.
Which way do you slide the tandems when the drives are overweight?
Forward, toward the nose. Sliding the tandems forward shortens the lever arm from the kingpin, so the trailer axles pick up more of the load and the drives lighten. Slide toward the problem: drives heavy means tandems forward, trailer heavy means tandems back.
How much weight does one tandem hole move?
It depends on the load. At a 40 ft kingpin distance with 4 in hole spacing, a trailer carrying 12,000 lb moves about 100 lb per hole, a trailer carrying 30,000 lb moves about 250 lb per hole and a maxed-out trailer at 34,000 lb moves about 283 lb per hole. With 6 in spacing the figures are about 150, 375 and 425 lb. The rule of thumb is 250 lb per hole at 4 in spacing and 400 lb per hole at 6 in spacing.
Can sliding the tandems fix an overweight gross weight?
No. Sliding moves weight between axle groups and never changes the gross weight. A rig over 80,000 lb stays over after any slide. Remove freight, reload the trailer or get an overweight permit. The bridge formula can also set a gross limit below 80,000 lb on a short wheelbase.
How much weight does sliding the fifth wheel move?
About 250 to 500 lb per notch between the steer axle and the drive axles. Sliding forward moves weight onto the steer axle. Sliding back moves weight onto the drives. The trailer axle weight does not change. A common rule is about 100 lb per inch of slide. Reweigh after every move.
What is the maximum weight on a steer axle?
The federal single axle ceiling is 20,000 lb, but the practical limit is the lowest of the axle rating on the door sticker and the combined rating of the two steer tires. A standard Load Range G steer tire pair allows 12,350 lb. Most drivers plan the steer axle at about 12,000 lb. FHWA guidance bars states from setting a steer limit below the manufacturer axle rating or 20,000 lb, whichever is lower.
Related tools
- Kingpin Law Checker: check the new kingpin distance against every state on the route after a tandem slide.
- Bridge Formula Axle Weight Checker: test every axle group against the bridge formula, not just the 34,000 lb tandem cap.
- Federal Size Limits Checker: check length, width and height limits for your configuration on the National Network.
- State Legal Limits Table: compare legal size and weight limits across all 50 states and DC in one table.
- Tire Compliance Checker: run a steer tire against the tread depth, defect, load and pressure rules.
- Pre-Trip Inspection Checklist: walk the full pre-trip inspection, including axles, suspension and slider pins.
- Trucking Tools: browse every free calculator on Trucking Mind.
Sources
- 23 CFR 658.17, Weight. ecfr.gov/current/title-23/section-658.17 Accessed November 19, 2026.
- 23 USC 127, Vehicle weight limitations. law.cornell.edu/uscode/text/23/127 Accessed November 19, 2026.
- Federal Highway Administration, Oversize/Overweight Load Permits. ops.fhwa.dot.gov/Freight/sw/permit_report/index.htm Accessed November 19, 2026.
- J.J. Keller Compliance Network, Size and Weight Limits. jjkellercompliancenetwork.com/institute/introduction-2656888101 Accessed November 19, 2026.
- AltitudeCraft, How to Slide Tandems: Which Way, How Far and 7 Steps. altitudecraft.com/blogs/insights/how-to-slide-tandem-axles-complete-trucker-guide Accessed November 19, 2026.
- ScaleRight, How to Slide Tandems to Fix Overweight Axles. scalerightapp.com/how-to-slide-tandems/ Accessed November 19, 2026.
- Blue Ink Tech, Adjusting Truck Weight by Sliding the 5th Wheel or Trailer Tandem Axle. blueinktech.com/blog/adjusting-truck-loads-by-sliding-the-5th-wheel-and-trailer-tandem-axle Accessed November 19, 2026.
- EngineerFix, How Much Weight Does Sliding the 5th Wheel Move? engineerfix.com/how-much-weight-does-sliding-the-5th-wheel-move/ Accessed November 19, 2026.