One container at a time. This checker tests one roll-off or hook-lift container against 49 CFR 393.134: front blocking, front restraint, the rear securement options and the 6 ft 7 in rear distance limit. A Fail result means the container must not move until the fix is in place.
Answer each question for the container on the truck now. Every answer updates as you change each field.
The container and the vehicle
Most roll-off and hook-lift trucks have no integral system. Section 393.134(b) applies to them in full. When in doubt, answer no.
The front of the container
The rear of the container
Enter the distance in decimal feet. A mechanism 6 ft 7 in from the rear enters as 6.58. Measure from the rearmost face of the container to the attachment point with a tape. Leave the field blank if the distance is not measured yet.
Ready to roll: the container meets 49 CFR 393.134
The container meets every part of 49 CFR 393.134(b). Keep the recheck schedule in the notes.
| Check | Result | Detail |
|---|---|---|
| Front blocking against forward movement | Pass | Blocked against forward movement by the lifting device and the front stops together (49 CFR 393.134(b)(1)). |
| Front restraint against lateral and vertical movement | Pass | Secured to the front of the vehicle against lateral and vertical movement by the lifting device (49 CFR 393.134(b)(2)). |
| Rear securement | Pass | Rear secured by option (iii): two hooks securing both sides of the container to the vehicle chassis (49 CFR 393.134(b)(3)(iii)). |
| Rear mechanism distance | Pass | 4 ft from the rear of the container. Inside the 6 ft 7 in limit in 49 CFR 393.134(b)(4). |
The figures
| Figure | Value | Note |
|---|---|---|
| Container type | Roll-off container | 49 CFR 393.134 applies |
| Front blocking | Lifting device and front stops | Section 393.134(b)(1) |
| Front restraint | Lifting device | Section 393.134(b)(2) |
| Rear securement | Option (iii): two hooks to the vehicle chassis | Section 393.134(b)(3) |
| Rear distance | 4 ft | Limit 6 ft 7 in (2 m) |
| Margin inside the limit | 2 ft 7 in | Inside the limit |
What to do
- Recheck the container and the securement devices within the first 50 miles and again at each duty status change, after 3 hours of driving or after 150 miles, whichever comes first (49 CFR 392.9(b)).
Notes
- Section 393.134 applies to roll-on/roll-off and hook-lift containers carried on a vehicle with no integral securement system.
- The 6 ft 7 in figure is the regulation rounding of two meters. Two meters is 78.74 in. The regulation parenthetical governs.
- The load inside the container needs its own securement. Section 392.9(a)(1) requires the cargo to be properly distributed and adequately secured.
- A damaged tiedown is a violation, not an out-of-service defect. It does not count toward the securement.
This checker applies 49 CFR 393.134 to your answers. Confirm the measurements with a tape before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.
Quick answer: A roll-off or hook-lift container with no integral securement system needs four things under 49 CFR 393.134: blocking against forward movement at the front, a restraint against lateral and vertical movement at the front, one of three rear securement options and rear mechanisms within 6 ft 7 in of the rear of the container. When a front stop or lifting device is missing, damaged or not compatible, manual tiedowns must replace it at the same level of securement. This checker tests one container against each part of that rule.
What does 49 CFR 393.134 require for a roll-off container?
The rule is short and specific. Section 393.134 is the commodity-specific rule for roll-on/roll-off and hook-lift containers. It applies to every roll-off or hook-lift container carried on a vehicle with no integral securement system. A container on a vehicle with an integral system sits outside paragraph (b) of the section. The checker asks about that first because the answer decides which rule governs the load.
For a container the rule covers, four requirements must all hold at the same time. The front must block forward movement. The front must restrain lateral and vertical movement. The rear must carry one of three securement options. The rear mechanisms must sit within 6 ft 7 in of the rear of the container. A fifth rule covers the failure case: when a front stop or lifting device is missing, damaged or not compatible, manual tiedowns must replace it at the same level of securement.
| Requirement | What the rule says | Section |
|---|---|---|
| Front blocking | Blocked against forward movement by the lifting device, stops, a combination of both or another suitable restraint mechanism | 393.134(b)(1) |
| Front restraint | Secured to the front of the vehicle against lateral and vertical movement by the lifting device or another suitable restraint | 393.134(b)(2) |
| Rear securement | At least one of three options: one tiedown chassis to chassis, two lengthwise tiedowns to the side rails or two hooks to the chassis | 393.134(b)(3) |
| Rear distance | Rear mechanisms no more than 2 m (6 ft 7 in) from the rear of the container | 393.134(b)(4) |
| Fallback tiedowns | When a front stop or lifting device is missing, damaged or not compatible, manual tiedowns must provide the same level of securement | 393.134(b)(5) |
The commodity-specific rule takes precedence over the general securement rules when it gives additional requirements for the commodity. That precedence comes from 49 CFR 393.106(a). Precedence does not switch the general rules off.
The tiedown standards in 49 CFR 393.104 still apply to every tiedown on the load: no damaged or weakened components, no knots, edge protection where a tiedown touches the container. The aggregate working load limit rule in 49 CFR 393.106(d) still applies to the tiedowns used as a fallback: the aggregate limit must reach at least one half the weight of the load. The driver inspection duties in 49 CFR 392.9 still apply to every trip. The checker names each of those rules where it matters.
The rule covers the container, not the load inside it. A roll-off box full of debris still needs its contents contained and the cargo inside still falls under the general securement rules. An open container also needs a cover where state or local law requires one. Check the state rule for the route before you roll with an open box.
A shipping container on a chassis follows a different section, 49 CFR 393.126, with corner castings and twist locks instead of the roll-off rules. Use the Intermodal Container Securement Calculator for that equipment. For the working load limit of the tiedowns on any load, use the Flatbed Calculator, which carries the full tiedown tables from 49 CFR 393.108.
What is the 6 foot 7 inch rule for the rear of a roll-off container?
Paragraph (b)(4) of 49 CFR 393.134 sets one distance limit for the whole rule: the mechanisms used to secure the rear end of the container must be installed no more than two meters from the rear of the container. The regulation gives the distance in both units and the parenthetical reads 6 ft 7 in. Two meters converts to 78.74 in, so the regulation rounds up by about one quarter of an inch. The regulation parenthetical governs. This checker passes a rear mechanism at 6 ft 7 in exactly.
The measurement runs from the rearmost face of the container to the point where the rear mechanism attaches. For a tiedown, measure to the tiedown attachment point on the container side or chassis. For a hook, measure to the hook. Measure along the length of the container with a tape, not by eye. A mechanism that looks close can sit past the limit by a foot on a long container.
The limit exists because a rear mechanism mounted far forward leaves the back of the container free. The rear end can swing sideways, lift off the rails or slide back on a stop. Six feet seven inches keeps the hold-down close to the end it holds. The front of the container has no matching distance limit: the front rule is about the blocking and restraint devices, not about where they sit.
The distance limit applies to all three rear options equally. It applies to the single chassis-to-chassis tiedown, to both of the lengthwise tiedowns and to both hooks. When a container uses two mechanisms, measure each one. Both must sit within the limit. One hook at 5 ft and one at 8 ft fails the rule.
What are the three ways to secure the rear of a roll-off container?
Paragraph (b)(3) gives three options and requires at least one of them. Picking one option is enough. Fitting two options is allowed and common on trucks that run heavy boxes, but the rule asks for one.
Option (i) is one tiedown attached to both the vehicle chassis and the container chassis. A single tiedown does the whole rear job, so its working load limit and its condition carry the full weight of the requirement. A frayed or knotted tiedown fails the tiedown standards in 49 CFR 393.104 and does not count.
Option (ii) is two tiedowns installed lengthwise, each securing one side of the container to one of the vehicle side rails. Each side gets its own tiedown. One tiedown on one side is not option (ii). Both tiedowns run lengthwise along the container.
Option (iii) is two hooks, or an equivalent mechanism, securing both sides of the container to the vehicle chassis. The hooks must hold at least as effectively as the tiedowns in the first two options. Most roll-off trucks carry rear hold-down hooks as standard equipment, which makes option (iii) the usual setup in the field. A hook that is bent, cracked or worn past its working limit is a damaged component and cannot be relied on.
The rear options say nothing about the front. A container with a perfect rear setup and no front blocking still fails the rule. The checker tests the front and the rear separately for that reason.
What happens when a front stop or lifting device is damaged?
Paragraph (b)(5) covers the failure case. When one or more of the front stops or lifting devices are missing, damaged or not compatible, additional manually installed tiedowns must be used to secure the container to the vehicle. The tiedowns must provide the same level of securement as the missing, damaged or incompatible components.
Same level of securement means the tiedowns must do the job the failed component did. If the lifting device blocked forward movement, the tiedowns must block forward movement. If it restrained the front against lateral and vertical movement, the tiedowns must restrain the front against lateral and vertical movement. A single light strap across the front does not replace a steel stop.
The fallback is a fix for the load, not a permanent repair. A damaged lifting device or stop stays damaged. Section 393.104(b) bars damaged or weakened securement components from service, so the damaged part cannot go back into use until it is repaired or replaced. The checker flags the repair as an action whenever the fallback is in use.
Fallback tiedowns must meet the general tiedown rules. The aggregate working load limit of the tiedowns must reach at least one half the weight of the container and its contents under 49 CFR 393.106(d). Tiedowns must carry no knots and no damage. Edge protection is required wherever a tiedown touches a sharp edge of the container. The Flatbed Calculator carries the working load limit tables for chain, webbing, wire rope and steel strapping, so a driver can check whether the tiedowns on hand reach the required aggregate limit.
Incompatible is the case drivers miss. A container that does not match the truck stops or lifting device is incompatible even when nothing is broken. A box built for a different hoist, a rail spacing that does not line up or a lifting bar at the wrong height all trigger paragraph (b)(5). When the equipment does not match, the tiedowns go on before the truck moves.
Does a hook-lift container follow the same rule as a roll-off container?
Yes. Section 393.134 names both types in its title and in paragraph (a): the rules apply to the transportation of roll-on/roll-off or hook lift containers. The same four requirements and the same fallback rule govern both. The checker covers both types and the only difference in the result is the container name.
The equipment differs. A roll-off truck uses a cable hoist that pulls the container onto the bed over a rear roller. A hook-lift truck uses a hydraulic hook arm that picks the container up by a lifting bar at the front and rolls it onto the frame. The lifting device in paragraphs (b)(1) and (b)(2) is the cable hoist on one truck and the hook arm on the other.
The practical difference sits at the front. On a hook-lift truck the hook arm holds the front of the container through the lifting bar. The arm position is part of the securement. On a roll-off truck the cable hoist and the front stops share the job. Either way the front must block forward movement and restrain lateral and vertical movement. Either way a failed front device triggers the tiedown fallback in paragraph (b)(5).
Container sizes do not change the rule. A 10 yard box and a 40 yard box follow the same section. The 6 ft 7 in rear limit is the same on both. What changes with size is the weight. Weight drives the aggregate working load limit for any tiedowns in use.
What is an integral securement system?
Paragraph (b) opens with a scope limit: it covers each container carried on a vehicle which is not equipped with an integral securement system. A vehicle with an integral system sits outside the paragraph. The checker asks about the system first for that reason.
The regulation does not define the term. In practice an integral securement system is securement built into the vehicle and the container as a matched pair, such as a locking frame or a twist-lock setup designed into the truck bed. The system holds the container as part of the vehicle design rather than through add-on tiedowns or hooks.
Most roll-off and hook-lift trucks on the road do not carry an integral system. The container rides on rails and the lifting device, stops and rear hooks do the securing. That is the equipment paragraph (b) was written for. A driver who is unsure whether a truck has an integral system should apply paragraph (b) in full. Treating a standard rail truck as an integral-system truck leaves the container unsecured under the rule.
An integral system that is broken, disengaged or bypassed is not doing the securing. The general rules still require the cargo to be firmly immobilized or secured under 49 CFR 393.106(b). The driver inspection duties in 49 CFR 392.9 still apply. The checker returns a scope result for an integral-system vehicle and names the general rules to follow.
When must a driver recheck a roll-off load on the road?
Section 392.9 sets the recheck schedule for every cargo load. A roll-off container is no exception. The driver must confirm the load is properly distributed and adequately secured before driving. Within the first 50 miles after beginning a trip, the driver must inspect the cargo and the securement devices and adjust them as necessary, adding more securement devices where needed.
After the first 50 miles the driver must reexamine the cargo and the securement devices whenever one of three triggers comes first: a change of duty status, 3 hours of driving or 150 miles driven. The reexamination is a real inspection, not a glance in the mirror. Hooks can work loose, tiedowns can stretch and a container can settle on the rails after the first miles.
The sealed vehicle exception in paragraph (b)(4) does not cover an open roll-off box. It covers a driver ordered not to open a sealed vehicle and a vehicle loaded in a way that makes inspection impracticable. A roll-off container is open to inspection from the ground, so the schedule applies in full.
Keep the recheck with the trip records. The checker summary copies the result and the recheck action for that purpose. The Pre-Trip Inspection Checklist covers the wider vehicle inspection that runs alongside the cargo check.
How do you use the Roll-Off Container Securement Calculator?
- Pick the container type: roll-off or hook-lift.
- Answer whether the vehicle carries an integral securement system. A yes answer ends the check with a scope result.
- Pick how the front blocks forward movement and how it restrains lateral and vertical movement, then state the condition of the front stops and lifting device.
- When a front device is missing, damaged or not compatible, answer whether manual fallback tiedowns are installed.
- Pick the rear securement option and enter the distance from the rear mechanism to the rear of the container in decimal feet, or leave the distance blank if it is not measured yet.
- Read the verdict, the check table, the figures and the notes. A Fail result names the fix. A Fallback result names the repair. Copy the summary for the trip records.
Frequently asked questions
How far from the rear of the container can the rear securement be?
No more than 6 ft 7 in. Paragraph (b)(4) of 49 CFR 393.134 sets the limit at two meters. The regulation parenthetical reads 6 ft 7 in. Measure from the rearmost face of the container to the attachment point of the rear mechanism. The limit applies to all three rear options and to each mechanism when two are fitted.
Do I need tiedowns on a roll-off container?
It depends on the rear option and the front hardware. The rear needs one of three options: one tiedown chassis to chassis, two lengthwise tiedowns to the side rails or two hooks. Only the hook option uses no tiedown. The front normally needs no tiedown when the lifting device and stops are sound. When a front stop or lifting device is missing, damaged or not compatible, manual tiedowns must replace it at the same level of securement.
What is the difference between a roll-off container and a hook-lift container?
The loading equipment. A roll-off truck pulls the container on with a cable hoist over a rear roller. A hook-lift truck lifts it with a hydraulic hook arm that grabs a lifting bar at the front of the container. The securement rule is the same for both: 49 CFR 393.134 covers roll-on/roll-off and hook-lift containers in one section.
What counts as an integral securement system?
Securement built into the vehicle and the container as a matched pair, such as a locking frame or a twist-lock setup designed into the truck bed. The regulation does not define the term. Most roll-off and hook-lift trucks do not carry one: the container rides on rails and the lifting device, stops and rear hooks do the securing. When in doubt, apply paragraph (b) of 49 CFR 393.134 in full.
Can a damaged tiedown still count toward securement?
No. Section 393.104(b) bars tiedowns and securement components with damage or weakness that affects their performance, including any damage that reduces the working load limit. A damaged tiedown is a violation and it does not count toward the securement. Replace it before the truck moves.
Does the 6 ft 7 in limit apply to the front of the container?
No. The distance limit in paragraph (b)(4) covers the mechanisms used to secure the rear end of the container only. The front has no distance limit. The front rule is about the devices: blocking against forward movement and restraint against lateral and vertical movement.
Related tools
- Intermodal Container Securement Calculator: shipping containers on a chassis under 49 CFR 393.126.
- Flatbed Calculator: tiedown working load limit tables from 49 CFR 393.108 for the fallback tiedowns.
- Pre-Trip Inspection Checklist: the wider vehicle inspection that runs alongside the cargo check.
- Axle Weight Rebalance Calculator: a loaded roll-off box is heavy. A tandem slide changes the axle weights.
Sources
- 49 CFR 393.134: Specific securement requirements for roll-on/roll-off and hook lift containers (Cornell LII, read Nov 19, 2026)
- 49 CFR 393.104: Standards for cargo securement devices and systems (Cornell LII, read Nov 19, 2026)
- 49 CFR 393.106: General requirements for securing articles of cargo (Cornell LII, read Nov 19, 2026)
- 49 CFR 392.9: Inspection of cargo, cargo securement devices and systems (Cornell LII, read Nov 19, 2026)