One vehicle at a time. This calculator checks one automobile, light truck or van against 49 CFR 393.128, plus the strength test in 49 CFR 393.106(d). A vehicle over 10,000 lb moves to 49 CFR 393.130.
Enter the vehicle, the tiedowns and the working load limit. Every answer updates as you change each field.
The vehicle
Use the scale weight where it exists, or the weight on the title and the door jamb label. The rule weighs each vehicle on its own.
The tiedowns
The strength test (optional)
Read the working load limit off the tiedown tag. A common 2-inch ratchet strap is marked 3,333 lb. Leave the field blank to skip the strength test. Each tiedown credits half its working load limit under 49 CFR 393.106(d).
Meets the rule with checks
Meets the rule, with checks on Wheel restraint directions.
| Check | Result | Detail |
|---|---|---|
| Rule that applies | Info | 49 CFR 393.128 covers this automobile: it weighs 4,000 lb, within the 10,000 lb limit in 393.128(a). |
| Tiedown count | Pass | 4 tiedowns. The rule needs at least 2 tiedowns, restraining the vehicle at the front and rear (49 CFR 393.128(b)(1)). |
| Front restraint | Pass | The front is restrained. The rule needs restraint at both the front and rear (49 CFR 393.128(b)(1)). |
| Rear restraint | Pass | The rear is restrained. The rule needs restraint at both the front and rear (49 CFR 393.128(b)(1)). |
| Wheel restraint directions | Check | Wheel-fit tiedowns must provide restraint in the lateral, longitudinal and vertical directions (49 CFR 393.128(b)(3)). Confirm each strap sits over the tire tread and holds the wheel against movement in all three directions. |
| Edge protection | Info | No edge protectors are needed where synthetic webbing touches the tires (49 CFR 393.128(b)(4)). Fit edge protection where the webbing touches a sharp edge anywhere else (49 CFR 393.104(f)(4)). |
| Aggregate working load limit | Pass | Credited aggregate working load limit 6,666 lb. The rule needs at least half the vehicle weight: 2,000 lb (49 CFR 393.106(d)). Each tiedown credits half its WLL: 4 tiedowns at 3,333 lb. |
The figures
| Figure | Value | Note |
|---|---|---|
| Vehicle weight | 4,000 lb | Limit for 49 CFR 393.128: 10,000 lb |
| Rule that applies | 49 CFR 393.128 | Automobiles, light trucks and vans |
| Minimum tiedowns | 2 | 49 CFR 393.128(b)(1) |
| Tiedowns entered | 4 | Meets the minimum |
| Required aggregate WLL | 2,000 lb | Half the vehicle weight (49 CFR 393.106(d)) |
| Credited aggregate WLL | 6,666 lb | Each tiedown credits half its WLL |
What to do
- Confirm each wheel strap holds the wheel against movement in every direction before the trip starts.
Notes
- Reinspect the load within the first 50 miles after the trip starts, then at every duty change, every 3 hours of driving or every 150 miles, whichever comes first (49 CFR 392.9(b)).
- A damaged tiedown does not count toward the total. Using a damaged tiedown is a violation (49 CFR 393.104(b)).
- The WLL of a tiedown is the lowest WLL of any of its parts, including the tensioner, or the WLL of the anchor points, whichever is less (49 CFR 393.108(a)). Read the number off the tag.
- The rule applies to each vehicle on its own. Every vehicle on the transporter needs its own tiedowns.
This checker applies 49 CFR 393.128 and 49 CFR 393.106(d) to your answers. Confirm the tiedowns by hand before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.
Quick answer: An automobile, light truck or van at 10,000 lb or less needs at least two tiedowns that restrain it at the front and rear against lateral, forward, rearward and vertical movement. That is 49 CFR 393.128. Above 10,000 lb the vehicle moves to 49 CFR 393.130, which needs at least four tiedowns. This calculator checks the count, the front and rear restraint, the tiedown type and the aggregate working load limit for one vehicle.
How many tiedowns does a car need on an auto transporter?
Two. Section 393.128(b)(1) of 49 CFR says automobiles, light trucks and vans must be restrained at both the front and rear to prevent lateral, forward, rearward and vertical movement using a minimum of two tiedowns. The number is a floor, not a target. Two tiedowns meet the rule when each end of the vehicle is held and the strength test in section 393.106(d) passes.
The count runs per vehicle, not per load. A transporter carrying nine cars needs at least two tiedowns on each car. One strap shared between two vehicles counts for neither. Each vehicle is its own article of cargo under the rule, so the check runs nine times on a nine-car load.
Many carriers run four tiedowns, one at each wheel, as company policy. Four straps spread the load, hold the vehicle square and leave margin when one strap loosens or fails on the road. The rule allows it: nothing in section 393.128 caps the tiedown count. A carrier policy of four is stricter than the federal floor. The stricter number governs on those trucks.
The count alone never settles the question. Two tiedowns on the front axle only leave the rear free to swing. The rule needs restraint at both ends. Two tiedowns with a low working load limit can fail the strength test even when the count passes. This calculator checks the count, the front and rear restraint and the strength test together.
What is the 10,000-pound line in the auto transport rule?
Section 393.128(a) draws the line at 4,536 kg, which is 10,000 lb. Automobiles, light trucks and vans that individually weigh 10,000 lb or less fall under section 393.128. A vehicle heavier than 10,000 lb must be secured under section 393.130, the heavy equipment rule, which needs at least four tiedowns. The weight is per vehicle: a 6,000 lb pickup on a transporter full of 6,000 lb pickups is still a 6,000 lb vehicle under the rule.
At exactly 10,000 lb both sections cover the vehicle. Section 393.128 reaches vehicles at 10,000 lb or less. Section 393.130 reaches vehicles at 10,000 lb or more. This calculator applies section 393.128 at exactly 10,000 lb, since that is the rule written for automobiles, light trucks and vans. A carrier may also secure a lighter vehicle under section 393.130. Section 393.130(a) allows it. The four-tiedown setup is never wrong for a car.
Weight means actual weight, not the number on a brochure. Use the scale weight where it exists, or the weight on the title and the door jamb label. Electric pickups carry heavy battery packs, so some sit close to the 10,000 lb line. A vehicle that looks like an ordinary pickup can cross the line once the battery pack and the options are counted. Weigh the vehicle when the answer is close.
When the vehicle crosses the line, the Heavy Equipment Securement Calculator takes over. It checks the four-tiedown minimum, the lowered accessories and the articulation restraint that section 393.130 requires. Flattened or crushed vehicles are a different commodity again: section 393.132 covers them, with its own containment and tiedown rules. The Crushed Vehicle Securement Calculator checks those.
The length of the transporter itself is a size question, not a securement question. A traditional automobile transporter runs to 65 ft overall. A stinger-steered transporter runs to 80 ft under the statute at 49 USC 31111(b)(1)(G). The Federal Size Limits Checker covers the length side of the same trip.
What is the difference between structure-designed and wheel-fit tiedowns?
Section 393.128 splits tiedowns into two kinds. Each kind carries its own rule. Structure-designed tiedowns attach to the frame or body of the vehicle. Wheel-fit tiedowns fit over or around the wheels. Most auto haulers use wheel straps, but both kinds meet the rule when they are used the way the regulation describes.
Structure-designed tiedowns must use the mounting points the maker designed for that purpose. That is section 393.128(b)(2). The points are the ones the vehicle maker put on the frame or body for securing the vehicle in transport. A tiedown hooked to a suspension arm, a steering part or a brake line does not meet the rule. Those parts can bend or break under load. Check the vehicle manual or the maker guide for the transport points before the first haul.
Wheel-fit tiedowns must provide restraint in the lateral, longitudinal and vertical directions. That is section 393.128(b)(3). A strap over the tire tread holds the wheel down. The same strap must also stop the wheel from sliding sideways and rolling forward or back. A loose strap over a tire holds nothing in any direction. Seat each strap flat on the tread, center it on the wheel and tension it until the suspension settles slightly.
A mixed setup uses both kinds: wheel straps on one axle and structure tiedowns on the other, or a wheel strap backed by a frame tiedown. The calculator checks each kind against its own rule. The mounting point question applies to the structure-designed tiedowns. The direction check applies to the wheel-fit tiedowns.
Do wheel straps need edge protectors?
Not where the webbing touches the tires. Section 393.128(b)(4) says edge protectors are not required for synthetic webbing at points where the webbing comes in contact with the tires. The tire is round and soft, so the webbing faces no cutting edge there. That exemption is the only one in the rule. It covers tire contact only.
Everywhere else, the general rule applies. Section 393.104(f)(4) says edge protection must be used whenever a tiedown would be subject to abrasion or cutting at the point where it touches an article of cargo. A webbing strap that crosses a sharp deck edge, a metal bracket or a damaged rim needs protection at that point. The protection must resist abrasion, cutting and crushing.
Two limits catch haulers out. First, the tire-contact exemption covers synthetic webbing only. A chain or a wire rope gets no exemption. The contact points still need checking. Second, the exemption lives in section 393.128, so it does not apply above 10,000 lb. A vehicle secured under section 393.130 needs edge protection wherever the tiedown faces abrasion or cutting, tires included.
In practice, inspect every contact point when the vehicle is loaded. Run a hand along the webbing where it leaves the tire and crosses the deck. A frayed edge on a strap is a damaged tiedown. A damaged tiedown must not be used at all.
How strong must the tiedowns be?
Strong enough that the aggregate working load limit reaches at least half the vehicle weight. That is section 393.106(d). It applies on top of the tiedown count in section 393.128. A 4,000 lb car needs an aggregate working load limit of at least 2,000 lb. A 9,000 lb van needs at least 4,500 lb. The count test and the strength test both have to pass.
The aggregate is not a simple sum. Section 393.106(d) credits each tiedown by its routing. A tiedown that runs from an anchor point on the trailer to an anchor point on the vehicle credits half its working load limit. A tiedown that passes over or around the vehicle and anchors on the same side also credits half. Only a tiedown that crosses to an anchor point on the other side credits its full working load limit. Auto-transport tiedowns almost always credit at half. A frame tiedown is a direct anchor-to-anchor tiedown, while a wheel strap anchors on the deck on the same side of the wheel.
Worked example: a 4,000 lb car with two 2-inch ratchet straps marked 3,333 lb working load limit each. Each strap credits half its limit, so the aggregate is 3,333 lb against a required 2,000 lb. The strength test passes with room to spare. The same car with two unmarked 2-inch straps credits 2,000 lb each under the table in section 393.108, so the aggregate is 2,000 lb against a required 2,000 lb. It passes exactly, with no margin at all.
Use the working load limit, never the breaking strength. The breaking strength printed on some tags is about three times the working load limit. The regulation counts the working load limit only. Read the number off the tag. Where the tag is missing or unreadable, the tables in section 393.108 set the value: unmarked synthetic webbing runs 1,750 lb at 1 and 3/4 inches, 2,000 lb at 2 inches, 3,000 lb at 3 inches and 4,000 lb at 4 inches.
The working load limit of a tiedown is the lowest limit of any of its parts, including the tensioner, or the limit of the anchor points, whichever is less. That is section 393.108(a). A 3,333 lb strap on a 1,000 lb anchor point is a 1,000 lb tiedown. Check the anchor points as well as the straps. The full tables sit in the Flatbed Calculator, which carries the complete section 393.108 tiedown tables.
How often must a car hauler recheck the load?
Before the trip, within the first 50 miles, then at every duty change, every 3 hours of driving or every 150 miles, whichever comes first. That is section 392.9(b). It covers every truck and truck tractor hauling cargo. The driver must be satisfied the load is secure before driving. The driver must inspect the cargo and the securement devices within the first 50 miles after the trip starts, then reexamine them on the schedule above.
The 50-mile check matters most for car haulers. Vehicle suspension settles under the straps during the first miles. A strap that was tight at the dock can go slack by mile 20. Walk the load at the first safe stop, tension any strap that has loosened and add a tiedown where one is needed. The rule allows adding securement devices at any inspection.
A duty change restarts the clock. Returning from a break, a fuel stop or a meal means another look at the load before the wheels turn again. The same goes for the 3-hour and 150-mile marks: whichever comes first triggers the reexamination. Log the checks with the trip records. The Pre-Trip Inspection Checklist covers the pre-trip side of the same duty.
What happens when a tiedown is damaged?
It stops counting. Using it is a violation. Section 393.104(b) says all tiedowns and securement parts must be in proper working order when used, with no damaged or weakened components, including cracks or cuts that reduce the working load limit. A cut strap, a cracked hook or a bent ratchet is out of service until it is repaired or replaced.
A damaged tiedown does not count toward the tiedown count or the aggregate working load limit. A car held by two straps, one of which is cut, has one tiedown under the rule. The fix is a replacement strap, not a knot: section 393.104(f)(1) says tiedowns and securing devices must not contain knots. Section 393.104(f)(2) says a repaired tiedown must be repaired to the standard or the maker instructions.
A damaged tiedown is a violation, not an out-of-service condition on its own. The distinction matters at a roadside inspection: the inspector cites the violation and the driver fixes it, but the vehicle is not placed out of service for the damaged tiedown alone. That changes when the remaining securement cannot hold the load. A vehicle that is not secured at all is a different problem. The inspector can hold the vehicle until it is secured.
Check every strap before it goes on a vehicle. Look for cuts along the edge, fraying at the hook, stitching that has pulled loose and ratchets that slip under tension. Pull damaged gear out of the box so nobody grabs it in a hurry at the next load.
How do you use the Auto Transport Securement Calculator?
- Pick the vehicle type: automobile, light truck or van. The rule is the same for all three. The type labels the result.
- Enter the weight of the vehicle in pounds. Use the scale weight where it exists, or the weight on the title and the door jamb label. Above 10,000 lb the calculator switches to 49 CFR 393.130.
- Pick the tiedown type: wheel-fit straps over the tires, structure-designed tiedowns on the frame, or a mix of both. Pick the tiedown material as well.
- Enter the number of tiedowns on the vehicle, then say whether the front and the rear are restrained. For structure-designed tiedowns, say whether they use the mounting points the maker designed.
- Enter the working load limit printed on the tiedown tag, in pounds, to check the strength test. Leave it blank to skip the strength test.
- Read the verdict, the check table, the figures and the notes. Copy the summary for the trip records, or reset the calculator to start over.
Frequently asked questions
How many tiedowns are required to secure a car on a transporter?
At least two, under 49 CFR 393.128(b)(1). The two tiedowns must restrain the car at the front and rear against lateral, forward, rearward and vertical movement. The count runs per vehicle, so each car on the transporter needs its own two tiedowns. Many carriers run four tiedowns, one at each wheel, as company policy.
Does a pickup truck over 10,000 lb use a different rule?
Yes. A vehicle heavier than 10,000 lb leaves 49 CFR 393.128 and moves to 49 CFR 393.130, the heavy equipment rule. That rule needs at least four tiedowns, affixed as close as practicable to the front and rear or at designed mounting points. Accessory equipment must be lowered and secured. Articulated vehicles must be restrained against articulation.
Do wheel straps need edge protectors on tires?
No. Section 393.128(b)(4) says edge protectors are not required for synthetic webbing where the webbing touches the tires. The exemption covers tire contact only. Where the webbing touches a sharp edge anywhere else, section 393.104(f)(4) requires edge protection. Above 10,000 lb the tire-contact exemption does not apply at all.
What is the working load limit rule for car haulers?
The aggregate working load limit of the tiedowns must reach at least half the vehicle weight, under 49 CFR 393.106(d). Each auto-transport tiedown credits half its working load limit, so a 4,000 lb car needs 2,000 lb of credited limit. Two straps marked 3,333 lb credit 3,333 lb between them and pass. Use the working load limit from the tag, never the breaking strength.
Can I secure a car with two tiedowns?
Yes, when the two tiedowns restrain the car at the front and rear and the aggregate working load limit reaches half the car weight. Two tiedowns meet the federal floor in 49 CFR 393.128(b)(1). Many carriers still run four tiedowns as company policy. The stricter number governs on those trucks.
How often must I check the straps on a car hauler?
Before the trip starts, within the first 50 miles, then at every duty change, every 3 hours of driving or every 150 miles, whichever comes first. That is the schedule in 49 CFR 392.9(b). Vehicle suspension settles in the first miles, so the 50-mile check catches straps that have gone slack.
Related tools
- Heavy Equipment Securement Calculator: the 49 CFR 393.130 check for vehicles over 10,000 lb.
- Crushed Vehicle Securement Calculator: the 49 CFR 393.132 check for flattened or crushed vehicles.
- Flatbed Calculator: the full section 393.108 tiedown working load limit tables.
- Pre-Trip Inspection Checklist: the pre-trip inspection behind the 49 CFR 392.9 duty.
- Federal Size Limits Checker: the length side of the same trip, including the 65 ft and 80 ft auto transporter limits.
Sources
- 49 CFR 393.128: Securement requirements for automobiles, light trucks and vans (Cornell LII, read Nov 19, 2026)
- 49 CFR 393.130: Securement requirements for heavy vehicles, equipment and machinery (Cornell LII, read Nov 19, 2026)
- 49 CFR 393.106: General requirements for securing articles of cargo (Cornell LII, read Nov 19, 2026)
- 49 CFR 393.104: Standards for cargo securement devices and systems (Cornell LII, read Nov 19, 2026)
- 49 CFR 393.108: Determining the working load limit of a tiedown (Cornell LII, read Nov 19, 2026)
- 49 CFR 392.9: Inspection of cargo, cargo securement devices and systems (Cornell LII, read Nov 19, 2026)
- 67 FR 61225: Development of a North American Standard for Protection Against Shifting and Falling Cargo, final rule (govinfo, read Nov 19, 2026)