Skip to main content

Trucking Mind

One load at a time. This checker runs one crushed car load against 49 CFR 393.132: the tiedown count for the wall setup, the synthetic webbing ban and the leak and loose-part containment rules. A failing result means the load must not roll until the fix is in place.

Pick the wall setup, enter the tiedowns and the webbing use, then answer the containment questions. Every answer updates as you change each field.

The vehicle

The tiedowns

Containment

The two containment questions apply only when the load needs tiedowns. With four-side walls they do not apply, so the fields hide.

Strength check (optional)

Use the marked working load limit on the tiedown. The limit is the lowest rating of any part of the tiedown, including the tensioner, or the anchor point, whichever is less (49 CFR 393.108).

Meets 49 CFR 393.132

This configuration meets the rules for flattened or crushed vehicles in 49 CFR 393.132.

CheckResultDetail
Synthetic webbingPassNo synthetic webbing is in use. Section 393.132(b) prohibits webbing to secure crushed vehicles, so chain or wire rope is the safe choice.
Containment wallsPassWalls on the front and rear to the full height of the load block forward and rearward movement. Paragraph (c)(3) requires at least 3 tiedowns per vehicle stack plus the leak and loose-part containment in paragraph (c)(5).
Tiedowns per stackPass3 tiedowns per stack count against the 3 required by paragraph (c)(3).
Tiedown conditionPassAll tiedowns are undamaged and free of knots, as section 393.104(b) requires. Every tiedown on the load counts toward the tiedown count.
Liquid leak containmentPassA means to prevent liquid leaks from the bottom of the vehicle is fitted, as paragraph (c)(5)(i) requires.
Loose-part containmentPassLoose parts are contained from the bottom and all four sides to the full height of the cargo, as paragraph (c)(5)(i) requires. Synthetic material is permitted for this containment under paragraph (c)(5)(iii).
Aggregate working load limitInfoNot checked. Enter the stack weight and the working load limit per tiedown to run the strength check in section 393.106(d).

The figures

FigureValueNote
Tiedowns required per stack349 CFR 393.132(c)(3)
Tiedowns that count per stack3Damaged tiedowns do not count
Minimum tiedowns for the load33 per stack across 1 stack
Tiedowns you have on the load33 counting tiedowns per stack

What to do

  • Inspect the cargo and the tiedowns within the first 50 miles, then at each duty status change, after 3 hours of driving or after 150 miles, whichever comes first (49 CFR 392.9).

Notes

  • Section 393.106(d) also applies to crushed vehicles: the aggregate working load limit of the tiedowns on a stack must reach at least one-half of the stack weight.
  • A damaged tiedown is a violation under section 393.104(b), not an out-of-service condition. It does not count toward the tiedown count or the aggregate working load limit.
  • The commodity rule in section 393.132 takes precedence over the general tiedown count in section 393.110 for crushed vehicles (section 393.106(a)).
  • State rules can add requirements on top of the federal rule. Check the rules in each state on the route.

This checker applies 49 CFR 393.132, 393.104, 393.106 and 392.9 to your answers. It is general information. Confirm the measurements and the tiedown ratings before you rely on a result.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.

Quick answer: Crushed cars travel under their own rule, 49 CFR 393.132. Synthetic webbing is banned for securing them, except as a connector between chain or wire rope and an anchor point that never touches the cars. The tiedown count depends on the walls: four-side walls need none, three-side walls need 2 per stack, front and rear walls need 3 per stack and no walls need 4 per stack. Every option except four-side walls also needs leak containment at the bottom plus loose-part containment on the bottom and all four sides to the full height of the cargo.

Last reviewed: · Focus keyword: crushed car securement

Can you use ratchet straps on crushed cars?

No. Section 393.132(b) prohibits synthetic webbing to secure flattened or crushed vehicles. A ratchet strap is synthetic webbing, so it cannot hold a crushed car down, whatever its rating. The ban exists because crushed metal has torn edges that cut webbing under load.

The rule allows exactly one use for webbing: as a connector between wire rope or chain and an anchor point on the vehicle. The webbing must stay clear of the cars themselves. The regulation says so in plain terms: the webbing, regardless of whether edge protection is used, must not come into contact with the flattened or crushed cars. Edge protection does not make a webbing tiedown legal on this load.

Chain or wire rope does the holding on a crushed car load. Pick the tiedown from its marked working load limit and check the rating of every part, including the binder and the anchor point. The Flatbed Calculator carries the full working load limit tables from 49 CFR 393.108, including the chain grades most scrap haulers use.

The webbing ban is specific to crushed vehicles. Whole vehicles on an auto transporter use webbing over the tires under a different section, 49 CFR 393.128. The Auto Transport Securement Calculator covers that load. Do not carry the auto transport habit onto a crushed car load: the two rules point in opposite directions on webbing.

How many tiedowns does a stack of crushed cars need?

The count depends on the walls of the transport vehicle, not on the weight or the length of the stack. Section 393.132(c) gives four options and the carrier picks one. More walls mean fewer tiedowns. No walls mean the most tiedowns.

Containment wallsTiedowns per stackExtra containmentParagraph
Four sides, full height0None(c)(1)
Three sides, full height2Leak plus loose-part(c)(2)
Two sides, front and rear, full height3Leak plus loose-part(c)(3)
No qualifying walls4Leak plus loose-part(c)(4)

The count is per vehicle stack, not per load. A trailer with three stacks under the front-and-rear-wall option needs 3 tiedowns on each stack, 9 in total. Count each stack on its own and never share tiedowns between stacks.

The general tiedown count in 49 CFR 393.110 does not decide this load. Section 393.106(a) says the commodity-specific rules take precedence over the general requirements where they give additional requirements for a commodity. For crushed vehicles the commodity rule is 393.132 and its count governs.

Damaged tiedowns do not count. Section 393.104(b) prohibits the use of damaged securement devices, so a chain with a cracked link or a wire rope with broken strands is out of the count entirely. Enter damaged tiedowns in the checker and it removes them from the total before it compares the count with the rule.

What is a vehicle stack under 49 CFR 393.132?

A vehicle stack is a pile of flattened or crushed vehicles loaded as one unit. The regulation counts tiedowns per stack, so each stack is secured on its own. Two stacks side by side on one trailer are two stacks for the tiedown count, even if they touch.

Flattened vehicles are cars pressed flat at the crusher. Crushed vehicles are cars compacted into a cube or a bale. Both fall under section 393.132, which applies to automobiles, light trucks and vans that have been flattened or crushed. Whole vehicles that still roll fall under a different section, 49 CFR 393.128. Machinery over 10,000 lb falls under 49 CFR 393.130 and the Heavy Equipment Securement Calculator covers that load.

Other commodities have their own specific rules. Large boulders take chain-only tiedowns under 49 CFR 393.136. The Large Boulder Securement Calculator covers that load. Never borrow the count from another commodity: each specific rule sets its own numbers.

Stack height decides the wall test. The walls must reach the full height of the load, so the tallest stack on the trailer sets the height the walls must reach. A trailer with one tall stack and two short stacks needs walls tall enough for the tall one.

What counts as a containment wall under 49 CFR 393.132?

A containment wall must extend to the full height of the load and block movement of the cargo in the direction it faces. A wall that stops below the top of the load is not a containment wall under this section, whatever it is made of. The regulation also allows comparable means: a structure that does the same job as a wall counts, even if it is not a flat panel.

The two-side option is specific about direction. Paragraph (c)(3) needs walls that block forward and rearward movement, which means front and rear walls. Walls on the left and right only do not meet that paragraph. A load with side walls only falls back to paragraph (c)(4) and needs 4 tiedowns per stack.

Four-side walls are the only option that needs no tiedowns at all. The walls must block movement forward, rearward and sideways. A container or a sided body that meets that test carries the load without a single tiedown. The same option also drops the separate leak and loose-part containment in paragraph (c)(5), because that paragraph applies only to options (c)(2), (c)(3) and (c)(4).

Measure the walls against the loaded height, not the empty height. A stack that settles or a taller car on top can push the load above a wall that looked tall enough at the yard. Check the height again after loading, before the tiedowns go on.

What stops liquids and loose parts falling from a crushed car load?

Paragraph (c)(5) answers that question. It applies to every option except four-side walls. The vehicle must have a means to prevent liquids from leaking from the bottom, plus a means to prevent loose parts from falling from the bottom and all four sides to the full height of the cargo. Crushed cars still hold oil, fuel, coolant and washer fluid. Loose trim, glass and small metal parts shake free on the road.

The means can be structural walls, sides or sideboards, or suitable covering material, alone or in combinations. A sealed floor pan or tray handles the leak side. Sideboards, mesh or a tarp that reaches the full height of the cargo handles the loose-part side. What matters is the result: nothing leaks out of the bottom and nothing falls from any side.

Here is the one place synthetic material is welcome on this load. Paragraph (c)(5)(iii) permits synthetic material for the containment of loose parts. A synthetic tarp or mesh that contains loose parts is legal. The same material used as a tiedown against the cars is not. The line is the job the material does: containment is permitted, securement is prohibited.

An inspector checks containment from the ground. Walk the trailer before departure and look for gaps at the floor edge, at the corners and at the top of the sideboards. A gap that a loose part can pass through is a gap the rule does not allow.

Does the aggregate working load limit rule apply to crushed cars?

Yes. Section 393.106(d) applies to every article of cargo, including the commodities covered by the specific rules in sections 393.116 to 393.136. The aggregate working load limit of the tiedowns on a stack must reach at least one-half of the stack weight. The tiedown count in 393.132 and the strength test in 393.106(d) are two separate tests. A load must pass both.

How a tiedown counts depends on how it is rigged. A tiedown that goes over the load to an anchor point on the opposite side counts at its full working load limit. A tiedown that runs direct from the vehicle to the cargo, or over the cargo back to the same side, counts at one-half of its working load limit. The checker applies that split when you enter the rigging style.

A worked example shows why the rigging matters. A 6,000 lb stack needs 3,000 lb of aggregate working load limit. Three 3/8-in Grade 70 chains rated at 6,600 lb each, run over the load to the opposite side, credit 19,800 lb. The same three chains run direct credit 9,900 lb. Both pass here, but on a heavier stack the direct rigging can fail while the cross-vehicle rigging passes.

The working load limit of a tiedown is the lowest rating of any part of it, including the tensioner, or the rating of the anchor point, whichever is less. A 6,600 lb chain on a 5,400 lb binder is a 5,400 lb tiedown. Unmarked chain is treated as Grade 30, which rates far lower than Grade 70. Use the marked rating where one exists and the tables in 49 CFR 393.108 where it does not. The Flatbed Calculator lists the full tables.

Weight is the figure most drivers guess. A crushed car keeps most of its original weight: fluids and the battery come out at the crusher, but the steel stays. Weigh the stack where you can. Where you cannot, use a conservative figure and check the result against the checker before the load rolls. Weight also decides the axle limits, so run the Bridge Formula Axle Weight Checker for the weight side of the same trip.

How do you check a crushed car load on the road?

Section 392.9 puts the duty on the driver. Before the trip, the driver must confirm that the cargo is properly distributed and adequately secured. Within the first 50 miles, the driver must inspect the cargo and the securement devices and adjust them as needed, including adding more securement devices. After that, reexamination is required at each duty status change, after 3 hours of driving or after 150 miles, whichever comes first.

Crushed loads settle early. Stacks shift as the first miles shake them down. A chain that was tight at the yard can go slack by the 50-mile check. That first stop is the most important one on the trip. Check every tiedown, look for new gaps in the containment and check the floor for fresh leaks.

A damaged tiedown found on the road is a violation under section 393.104(b), not an out-of-service condition. It still has to come out of service: it does not count toward the tiedown count or the aggregate working load limit. Running with it risks a citation at the next inspection. Carry a spare chain and binder for exactly this moment.

Build the load check into the pre-trip routine. The Pre-Trip Inspection Checklist covers cargo securement alongside the vehicle inspection. The DVIR Checker covers the daily inspection report. A load that passes the checker at the yard still needs the driver checks on the road.

How do you use the Crushed Vehicle Securement Calculator?

  1. Pick the containment walls on the transport vehicle: four sides, three sides, front and rear, side walls only, one side or none, or walls below the full height of the load.
  2. Enter the number of vehicle stacks on the load and the tiedowns per stack, then enter how many tiedowns per stack are damaged or knotted.
  3. Pick the synthetic webbing use: none, connector only between chain or wire rope and anchor points, or webbing that touches the cars.
  4. Answer the two containment questions: liquid leak prevention at the bottom and loose-part containment on the bottom and all four sides to the full height of the cargo.
  5. Optional: enter the weight of one stack and the working load limit per tiedown, then pick the rigging style to run the strength check in section 393.106(d).
  6. Read the verdict, the check table, the figures and the notes. Copy the summary for the trip records, or reset the checker to start over.

Frequently asked questions

Can you use ratchet straps to secure crushed cars?

No. Section 393.132(b) prohibits synthetic webbing to secure flattened or crushed vehicles. A ratchet strap is synthetic webbing. Webbing may only connect wire rope or chain to anchor points. It must not touch the cars, even with edge protection. Use chain or wire rope against the load.

How many tiedowns are required for crushed cars with no walls?

At least 4 tiedowns per vehicle stack, under paragraph (c)(4) of 49 CFR 393.132. The load also needs a means to prevent liquid leaks from the bottom and a means to prevent loose parts falling from the bottom and all four sides to the full height of the cargo. The count is per stack, so three stacks need 12 tiedowns in total.

Do four-side walls mean no tiedowns are needed?

Yes, when the walls extend to the full height of the load and block movement forward, rearward and sideways. Paragraph (c)(1) of 49 CFR 393.132 requires no tiedowns for that setup. The separate leak and loose-part containment in paragraph (c)(5) does not apply either. Walls below the full height of the load do not count.

Can synthetic material be used anywhere on a crushed car load?

Yes, for containment only. Paragraph (c)(5)(iii) permits synthetic material for the containment of loose parts, so a synthetic tarp or mesh that keeps parts from falling is legal. The same material used as a tiedown against the cars is prohibited by section 393.132(b). The job the material does decides which rule applies.

What happens if a tiedown is damaged on a crushed car load?

Section 393.104(b) prohibits the use of damaged securement devices, so the tiedown must come out of service. It does not count toward the tiedown count or the aggregate working load limit. A damaged tiedown is a violation, not an out-of-service condition, but running with it risks a citation at the next inspection.

How often must a driver inspect a crushed car load?

Under 49 CFR 392.9, the driver inspects the cargo and the securement devices within the first 50 miles of the trip, then reexamines them at each duty status change, after 3 hours of driving or after 150 miles, whichever comes first. Crushed loads settle early, so the 50-mile check is the most important stop on the trip.

Related tools

Sources

Follow on WhatsApp Ask by Voice