One model, several sizes. A Freightliner Cascadia can take a 36, 38, 39 or 42 inch mattress depending on the sleeper package. Pick your truck below to see the size that fits your sleeper, plus the thickness and sheets to match.
Pick your truck. Every answer updates the result as you change each field. If you already measured the bunk, enter the numbers at the bottom. A tape reading beats the model table every time.
Your truck
Measured your berth? (optional)
Your mattress size is 38 x 80 inches.
Freightliner Cascadia, 72 inch sleeper, lower bunk.
The 72 inch Cascadia most often takes a 38 x 80 mattress. Some take a 39 x 80, which is twin XL width. Confirm the platform measures 38 x 80 before you order.
The checks
| Check | Result | Detail |
|---|---|---|
| Mattress size | 38 x 80 | The common fit for this truck. |
| Berth width | 38 inches | Across the bunk platform. |
| Berth length | 80 inches | Head to foot along the platform. |
| Thickness | 7 to 8 inches | For the lower bunk at your weight. |
| Sheets | Twin XL sheets. | Match the sheets to the width. |
The figures
| Figure | Value | Note |
|---|---|---|
| Size to order | 38 x 80 | The common fit for this truck. |
| Alternate size | 39 x 80 | Fits some trucks of this model. Measure to choose. |
| Berth width | 38 inches | Across the bunk platform. |
| Berth length | 80 inches | Head to foot along the platform. |
| Recommended thickness | 7 to 8 inches | Memory foam or hybrid. |
| Sheets that fit | Twin XL sheets. | Check the pocket depth against the thickness. |
What to do
- Measure the platform before you order. The listed size is the common fit, not a guarantee.
- Pick a thickness in the 7 to 8 inches range. Measure the clearance above the bunk before going thicker than 8 inches.
- If the platform measures differently, the alternate size is 39 x 80. Order the size that matches the tape, not the model name.
Notes
- The 72 inch Cascadia most often takes a 38 x 80 mattress. Some take a 39 x 80, which is twin XL width.
- 2018 to 2024. Current generation for most models. The listed sizes apply.
- Federal law sets a minimum mattress thickness of 4 inches in a sleeper berth, 49 CFR 393.76. A 4 inch mattress meets the rule. Most drivers sleep better on 6 to 8 inches.
This finder matches your truck to the mattress sizes listed in the published fitment guides. Confirm the result against your own tape reading before you order.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice — measure your berth before you order, because mattress sizes vary by sleeper package.
Quick answer: Most semi truck sleeper berths take a mattress 80 inches long and 36 to 42 inches wide. The most common replacement size is 42 x 80 inches. The most common factory size is 38 x 80 inches, fitted to the Kenworth T680 plus the Peterbilt 579. The size that fits your truck depends on the make, the model, the sleeper package, plus the bunk position. Pick your truck in the finder above to see the size for your sleeper, the thickness that suits your weight, plus the sheets that fit.
What size mattress fits a semi truck?
A semi truck mattress is almost always 80 inches long. The width is the part that changes. Standard sleeper berth mattresses run 32 to 42 inches wide. The common widths are 36, 38, 39 and 42 inches. The 42 x 80 inch mattress is the most common replacement size in the United States. The 38 x 80 inch mattress is the most common factory size, fitted as standard to the Kenworth T680 plus the Peterbilt 579. Narrower sizes serve smaller sleepers plus upper bunks: 32 x 80 is the standard upper bunk size. Some short sleepers take a 35 or 36 inch mattress.
Length is simpler than width. Nearly every Class 8 sleeper bunk measures 80 inches from head to foot, which is why 80 inches is the standard mattress length. A few bunks break the pattern. The Volvo VNL 760 bunk measures 39 x 81 inches. The Volvo VNL 860 bunk measures 42 x 79 inches. The Peterbilt 579 UltraLoft lower bunk platform measures 85 x 42 inches, so a standard 42 x 80 mattress fits with room to spare. A mattress one inch shorter or longer than the platform still works. A mattress wider than the platform does not.
The sleeper size number on the spec sheet is not the mattress size. A 72 inch sleeper is 72 inches long from the back of the cab to the rear wall. The mattress sits across the back of that space, so its width depends on the interior layout, not on the sleeper length. Two trucks with 72 inch sleepers can take different mattress widths. The table below lists the standard sizes. The finder above matches them to your truck.
| Size | Where it fits | Notes |
|---|---|---|
| 28 x 80 | Narrow upper bunks | T680 52 inch upper bunk. Needs custom sheets. |
| 32 x 80 | Upper bunks | The standard upper bunk size across most models. |
| 35 x 79 | Some short sleepers | Older Volvo plus International short sleepers. |
| 36 x 80 | Standard lower bunk | Small sleepers. The most common Cascadia factory size. |
| 38 x 80 | Factory standard | T680 plus 579 factory size. Same as a twin XL. |
| 39 x 80 | Twin XL width | VNL 760 replacement size. Some Cascadia packages. |
| 39 x 81 | Volvo VNL 760 | The VNL 760 bunk size. Order a 39 x 80 replacement. |
| 42 x 79 | Volvo VNL 860 | The VNL 860 bunk size. Order a 42 x 80 replacement. |
| 42 x 80 | Wide sleepers | The most common replacement size. Needs oversize sheets. |
What size mattress fits my truck?
The table below covers the eight most common sleeper models on American roads. Pick your make, model plus sleeper size in the finder above for the exact answer for your truck. Where the table shows a range, the size depends on the sleeper package. The finder tells you the most likely size plus what to measure.
| Truck | Sleepers | Lower bunk | Upper bunk | Notes |
|---|---|---|---|---|
| Freightliner Cascadia | 48, 60, 72, 82 inch | 36 to 42 x 80 | 32 to 36 x 80 | 72 inch most often 38 x 80. XT plus raised roof 42 x 80. |
| Kenworth T680 | 40, 52, 76 inch | 32 to 42 x 80 | 28 to 32 x 80 | 76 inch factory size 38 x 80. 52 inch sources disagree. |
| Kenworth W900 | 38, 62, 72, 86 inch | 36 to 42 x 80 | 32 x 80 | 72 inch AeroCab plus 86 inch Studio 42 x 80. |
| Peterbilt 579 | 44, 58, 72, 80 inch | 36 to 42 x 80 | 32 to 36 x 80 | 72 inch most often 38 x 80. UltraLoft 42 x 80. |
| Peterbilt 389 | 44, 58, 72, 78 inch | 36 to 42 x 80 | 32 x 80 | Larger Ultra sleepers 42 x 80. |
| Volvo VNL 760 | 61, 70 inch | 39 x 81 | 32 x 80 | Order a 39 x 80 replacement. |
| Volvo VNL 860 | 77 inch | 42 x 79 | 32 x 80 | Order a 42 x 80 replacement. |
| Mack Anthem | 48, 70 inch | 36 to 42 x 80 | 32 x 80 | Sources disagree on the 70 inch sleeper. Measure. |
| International LT | 56, 73 inch | 36 to 42 x 80 | 32 to 33.5 x 80 | 56 inch 36 x 80. 73 inch lower 42 x 80. |
Every size in this table comes from the published fitment guides listed in the sources section. No size here is a manufacturer specification, because the manufacturers do not publish mattress sizes in a single public table. The guides agree on most models. Where they disagree, this page says so and tells you to measure. A used truck can also differ from the table if a previous owner changed the interior, which is another reason the tape reading matters more than the model name.
Why does the same truck model take different mattress sizes?
The sleeper package decides the width. A Freightliner Cascadia comes in 48, 60, 72 and 82 inch sleepers. The bunk width grows with the package. The 48 inch sleeper takes a 36 inch mattress. The 72 inch sleeper most often takes a 38 inch mattress. The 72 inch XT plus the 82 inch raised roof take a 42 inch mattress. The model name alone cannot pin the size down. The sleeper size can, most of the time.
Trim level plus factory options add a second layer. A premium interior package can widen the bunk by a few inches. A double-bunk configuration changes the lower bunk width on some models, because the upper bunk hardware takes space. Model year matters less than most drivers expect: the Kenworth T680 has used the same 38 x 80 factory mattress across its trims since launch. The Volvo VNL 760 bunk has stayed 39 x 81 through the generation change. Older trucks vary more. A truck built before 2010 is more likely to differ from the published guides than a current model.
Fleet specs plus aftermarket work add a third layer. A fleet can order a non-standard bunk. A previous owner can swap the bunk platform, add insulation, or fit a custom base. That is why every fitment guide carries the same warning: measure the bunk before you order. The finder follows the same rule. It gives you the most likely size for your truck, then tells you to confirm it with a tape measure. The measure step takes two minutes. A wrong mattress costs a return shipment plus a week of bad sleep.
How do you measure a sleeper berth?
Measure the bunk platform, not the old mattress. A worn mattress sags plus shrinks, so it reads smaller than the space it sits in. The platform is the true size. Pull the old mattress off, clear the bunk, then measure with a tape measure, not a phone app. Bunk platforms are not always perfectly rectangular, so measure at more than one point.
- Pull the old mattress off the bunk platform.
- Measure the width at the head, the middle, plus the foot.
- Measure the length on both sides of the platform.
- Write down the smallest width plus the smallest length.
- Measure the clearance from the platform to the ceiling or upper bunk.
- Enter the numbers in the finder above to match a standard size.
Use the smallest reading on each side. A mattress that fits the narrowest point fits everywhere. A mattress cut to the widest point jams at the narrow end. Leave about half an inch of room around the edges for sheets plus bedding. If the platform measures wall to wall, order the mattress one inch smaller than the tape reading on each side. That half inch per side is the standard advice from the custom mattress makers. It stops the mattress from bunching against the cab walls.
If the numbers do not match a standard size, the finder tells you so. A berth that measures 44 inches wide or 76 inches long sits outside the standard range. A custom cut mattress is the fix. Memory foam trims cleanly with a long blade, so some drivers buy a larger foam mattress plus trim it down. That works for foam. It does not work for a hybrid or innerspring mattress, where cutting opens the coil unit.
How thick should a semi truck mattress be?
Six to eight inches is the sweet spot for most sleeper cabs. That range is thick enough for real pressure relief and thin enough to clear the cab fixtures plus the headroom above the bunk. Factory mattresses are typically four to five inches thick, which is one reason drivers complain about sleeping in the truck. Federal law sets the floor at four inches: 49 CFR 393.76 requires a mattress at least four inches thick in a sleeper berth. A four inch mattress meets the rule. Most drivers sleep better on six to eight inches.
Weight sets the thickness. Drivers under 180 lb sleep well on six to eight inches. Drivers between 180 and 220 lb do best on seven to eight inches. Drivers over 220 lb benefit from eight to ten inches for support, because a thin mattress bottoms out under more weight. The finder above works the thickness out from the weight you pick. Upper bunks are the exception: five to six inches is the right range up top, whatever the driver weighs, because the clearance to the ceiling is tight.
Density matters more than thickness. A thick mattress made from low-density foam sags within months. Look for high-density foam: at least 1.8 lb per cubic foot for polyfoam, three to five lb per cubic foot for memory foam. A seven inch high-density mattress outlasts a ten inch low-density mattress. Before going thicker than eight inches, measure the clearance from the platform to anything overhead: the ceiling, the upper bunk, or a cabinet. A mattress that leaves no room to sit up is a bad trade for an extra inch of foam.
| Thickness | Best for | Watch out |
|---|---|---|
| 4 to 5 inches | Factory standard, tight cabs | Too thin for nightly use. Meets the 4 inch rule only. |
| 6 inches | Upper bunks, drivers under 180 lb | Light support for heavier drivers. |
| 7 to 8 inches | Most drivers, lower bunks | Check overhead clearance before ordering. |
| 8 to 10 inches | Drivers over 220 lb, lower bunks | Can sit too tall in low-clearance cabs. |
Can you use a twin XL mattress in a semi truck?
Yes, if your berth is 38 or 39 inches wide. A twin XL mattress measures 38 x 80 inches, which is exactly the factory size for the Kenworth T680 plus the Peterbilt 579. It is also the standard fit for the 72 inch Freightliner Cascadia. It also fits the Volvo VNL 760 with a small gap, because the VNL 760 bunk is 39 inches wide. Twin XL is the easiest truck mattress size to shop for, because every mattress seller stocks it.
A twin XL does not fit every truck. On a 42 inch berth it leaves a four inch gap down one side, which is enough to lose a pillow through. On a 36 inch berth it is two inches too wide, so it bunches against the cab wall. On a 32 inch upper bunk it does not fit at all. Check the width first, then decide. The finder above tells you whether a twin XL fits your truck.
Do not buy a regular twin mattress for a truck. A standard twin measures 38 x 75 inches, which is five inches shorter than the bunk. The gap at the foot end is uncomfortable. The mattress slides. Twin XL is the right home size for a truck. Anything shorter is a compromise that shows on the first night.
What size mattress fits an upper bunk?
The standard upper bunk mattress is 32 x 80 inches. That size fits the upper bunk on the T680, the W900, the 579, the 389, the VNL 760, the VNL 860, the Anthem, plus the International LT. A few upper bunks break the pattern: the T680 52 inch upper bunk is 28 inches wide, the 579 UltraLoft upper bunk is 36 inches wide. The LT 73 inch upper bunk is listed at 33.2 inches in one fitment guide. Team drivers sleep on the upper bunk while the truck rolls, so the fit matters as much as the lower bunk.
Thickness matters more up top than down below. Five to six inches is the right range for an upper bunk. A thicker mattress closes the gap to the ceiling and makes it hard to sit up, which matters when the driver on break needs to get dressed or reach a bag. The clearance check in the measure section above is the step that catches this. If the clearance is tight, drop to a five inch mattress rather than forcing a thicker one in.
Some sleepers have no upper bunk at all. The 48 inch Cascadia, the 40 inch T680, the 44 inch 579, the 44 inch 389, plus the 56 inch International LT are single-bunk sleepers. Pick the upper bunk in the finder for one of those trucks and the finder says so. Team drivers who run a split sleeper schedule need both bunks to work: the Sleeper Berth Split Calculator checks whether a 7/3 or 8/2 split is legal. The Team HOS Planner plans two-driver schedules across both bunks.
What sheets fit a semi truck mattress?
Twin XL sheets fit any truck mattress from 36 to 39 inches wide. That covers the T680, the 579, the 72 inch Cascadia, plus the VNL 760. The fitted sheet goes on snug at 38 inches and slightly loose at 36 inches. A 42 inch mattress needs oversize twin XL sheets or truck-specific sheet sets, because a standard twin XL fitted sheet is too narrow to stay on. A 32 inch upper bunk mattress takes truck bunk sheets, or a twin XL with the extra width tucked under.
Pocket depth matters as much as width. A fitted sheet made for a six inch home mattress will not stay on a ten inch truck mattress. Check the pocket depth on the sheet packaging against the mattress thickness before you buy. Deep-pocket twin XL sheets handle eight to ten inch mattresses. Standard pockets handle six to seven inches. If the sheet pops off at the corners on the first night, the pocket is too shallow, not the width.
Buy two sets. A truck mattress is harder to air out than a home mattress. The cab sees more dust plus road grime. A spare set means the bunk gets fresh sheets on a reset day without waiting for laundry. Waterproof mattress protectors in twin XL size fit the same range as the sheets. They protect the foam from spills plus sweat on long hauls.
How much does a semi truck mattress cost?
Budget memory foam truck mattresses run $100 to $125. Mid-range seven to ten inch memory foam or hybrid mattresses run $145 to $190. Premium builds with cooling gel, a 120-night trial, plus a ten-year warranty run $190 and up. Those bands come from Amazon roundup prices as reported on November 17 to 18, 2026, in the research behind this page. They are dated static bands, not live prices. Prices change with sales plus stock, so check the current listing before you buy.
Thickness plus density drive the price more than the brand name. A seven inch high-density memory foam mattress costs more than a ten inch low-density mattress. It lasts longer. Cooling covers, gel-infused foam, plus hybrid coil builds add cost. A 120-night trial plus a ten-year warranty are worth paying for on a mattress you sleep on 250 nights a year. Divide the price by the nights you will sleep on it: a $180 mattress over two years of full-time driving costs about 36 cents a night.
If the mattress is part of a first-truck setup, budget it with the rest of the gear. The New Trucker Gear Cost Estimator totals the starter kit, mattress included, across budget, mid-range, plus premium tiers. A mattress is one of the cheaper items on that list. It is the one you use every single night.
Memory foam or hybrid: which mattress type suits a sleeper cab?
Memory foam dominates truck mattresses, for good reason. It conforms to the body, relieves pressure points, plus isolates vibration from the engine plus the road. It folds for stowage, which matters in a cab where the bunk sometimes doubles as a seat or a work surface. It trims cleanly with a long blade, so a driver with a non-standard berth can cut a larger foam mattress down to size. The drawback is heat: standard memory foam sleeps warm, which is a problem on southern routes or in a cab with the engine off.
Hybrid mattresses pair a pocket coil base with a foam top. They sleep cooler than all-foam builds, because air moves through the coil layer. They feel more like a home mattress, with more bounce plus easier movement. The trade-offs are weight plus size: a hybrid is heavier to carry into the cab. It cannot be trimmed to fit a non-standard berth. Cutting a hybrid opens the coil unit. For a standard 42 x 80 berth, a hybrid is a strong choice. For an odd-size berth, foam is the safer pick.
Innerspring mattresses are the budget option. They show it. They are thin, they wear fast under nightly use, plus they transfer vibration more than foam. Gel-infused foam splits the difference: it keeps the foam feel with a cooler sleep surface. Whatever type you pick, check the foam density before the brand name. High-density foam at 1.8 lb per cubic foot for the base layer, plus three to five lb per cubic foot for the memory foam layer, is the mark of a mattress built for nightly use rather than a weekend camper.
What other tools help life on the road?
A mattress is one part of a sleeper cab that works. The rest of the cab gear decides whether the nights are comfortable: cold food, power for cooking, security while parked, plus a cab that stays warm or cool without burning fuel all night. These tools cover the rest of the setup.
- Truck Fridge Power Calculator: work out whether the battery survives the 10-hour break with the fridge running.
- Inverter Size Calculator for Trucks: size the inverter for a microwave, a heated mattress pad, plus the rest of the cab load.
- Dash Cam Storage Calculator: size the SD card so the camera keeps the footage that matters.
- Jump Starter Size Checker: check whether a consumer jump pack can turn a Class 8 diesel on a cold morning.
- Semi Truck Tire Pressure Calculator: set the pressure for the load on each tire, from the load-inflation tables.
- Truck Idle Cost Calculator: work out what overnight idling for heat or air conditioning costs per year.
- Truck GPS Cost Comparison Calculator: compare a Garmin dezl against a phone app over one, three, plus five years.
- LED Light Bar Legal Checker: check whether an auxiliary light bar is street-legal in your state.
- New Trucker Gear Cost Estimator: budget the full starter kit, mattress included, across budget, mid-range, plus premium tiers.
Good sleep starts with the right mattress size, then the cab around it. A fridge that runs all night without killing the battery, an inverter sized for the real load, plus a fair idea of what overnight idling costs will do more for rest quality than any mattress upgrade alone.
Frequently asked questions
What is the most common semi truck mattress size?
The most common semi truck mattress size is 42 x 80 inches. It is the standard replacement size for wide sleepers, including the Peterbilt 579 UltraLoft, the Kenworth W900 Studio, plus the Freightliner Cascadia XT. The most common factory size is 38 x 80 inches, fitted as standard to the Kenworth T680 plus the Peterbilt 579.
What size mattress fits a Freightliner Cascadia?
It depends on the sleeper package. The 48 and 60 inch sleepers take a 36 x 80 mattress. The 72 inch sleeper most often takes a 38 x 80 mattress, with some taking a 39 x 80. The 72 inch XT plus the 82 inch raised roof take a 42 x 80 mattress. The factory mattress is most often 36 x 80. Measure the bunk platform before you order.
Will a twin XL mattress fit in a semi truck?
Yes, if the berth is 38 or 39 inches wide. A twin XL mattress measures 38 x 80 inches, which matches the factory size for the Kenworth T680 plus the Peterbilt 579. It does not fit a 42 inch berth, where it leaves a four inch gap, or a 36 inch berth, where it is two inches too wide. A regular twin at 38 x 75 inches is too short for a truck bunk.
How thick should a semi truck mattress be?
Six to eight inches suits most drivers on a lower bunk. Drivers under 180 lb sleep well on six to eight inches. Drivers between 180 and 220 lb do best on seven to eight inches. Drivers over 220 lb benefit from eight to ten inches. Upper bunks need five to six inches for clearance. Federal law sets the minimum at four inches in 49 CFR 393.76. Measure the clearance above the bunk before going thicker than eight inches.
What size mattress fits a Kenworth T680?
The 76 inch T680 takes a 38 x 80 mattress, which is the factory size in every trim. Some 76 inch trims take a 39 or 42 inch mattress. The 52 inch sleeper takes a 36 x 80 mattress, although the published guides disagree: one lists a 32 inch standard lower bunk with a 38 inch option. The 40 inch sleeper takes a 36 x 80 mattress with a single bunk only. Measure the platform before you order.
How do I measure my sleeper berth for a mattress?
Pull the old mattress off the bunk platform, then measure the platform itself, not the mattress. Measure the width at the head, the middle, plus the foot. Measure the length on both sides. Use the smallest reading on each side, then leave about half an inch of room around the edges for sheets. Enter the numbers in the finder above to match a standard size.
Related tools
- Sleeper Berth Split Calculator: check whether a 7/3 or 8/2 split is legal before you plan the sleep around it.
- Team HOS Planner: plan two-driver schedules across both bunks.
- 34-Hour Restart Planner: plan a restart around real rest, not just the clock.
- HOS Calculator: work out driving time plus rest time under the hours of service rules.
Sources
- SleepDog: The Best Semi Truck Mattress for Your Over the Road Sleeper (mattress sizes by truck model, read Nov 19, 2026)
- SleepDog: What Size Bed is in a Tractor Trailer? (VNL, Mack, International, LT bunk sizes, read Nov 19, 2026)
- 4 State Trucks: Semi-Truck Mattress Sizes, Fitment Chart and Buying Guide (fitment chart by model plus sleeper, read Nov 19, 2026)
- Estee Bedding: Semi Truck Mattress Size Guide by Model (size reference by make plus model, read Nov 19, 2026)
- O Trucking: Sleeper Cab Sizes Chart 2026 (sleeper options by model, updated Sep 30, 2026, read Nov 19, 2026)
- Absolute Mattress: How To Size A Replacement Semi Truck Mattress (sizes by brand, updated Jul 26, 2025, read Nov 19, 2026)
- Banner Mattress: Best Semi-Truck Mattresses for 2026 (thickness guidance, read Nov 19, 2026)
- 49 CFR 393.76: Sleeper berths (Cornell LII, 4 inch minimum mattress thickness, read Nov 19, 2026)