Skip to main content

Trucking Mind

4K eats cards fast. A 4K front plus 1080p rear setup writes about 27.9 GB an hour. A 512 GB card holds under two days of 8-hour driving before loop-over starts. Work out the size before you buy the card, not after the clip you need is gone.

Enter your setup. Every answer updates the result as you change each field.

Your camera

Rear, cabin, plus side channels usually record at 1080p. Pick 2K if yours record higher.

Your driving

Three to five days is a sensible target. A clip from Friday must survive the weekend.

Your card

If you have not bought a card yet, pick the size you are considering. Check the camera manual for the real limit. Many truck dash cams top out at 512 GB.

Most cameras keep 10 to 30 percent of the card for locked event files. Loop recording cannot use that space.

Parking mode

Parking mode needs a hardwire kit on most cameras. A 10-hour overnight break is the usual case for a trucker.

Too small: this card holds 1.8 days, not 3.

4K front, 2 channels, 8 driving hours a day.

Your setup writes 27.9 GB an hour, 223.2 GB a day. The 512 GB card keeps 404.7 GB usable after formatting plus the 15 percent event reserve, which covers 14.5 hours of driving, about 1.8 days. 3 days needs 847.1 GB of card space, so a 1 TB card is the smallest size that covers it.

The checks

CheckResultDetail
Card against targetToo smallThe card holds 1.8 days. The target is 3 days.
Camera card limitToo bigThe 1 TB card you need is bigger than the 512 GB your camera supports.
Three-day minimumUnder 3 daysThe card holds 1.8 days. Aim for 3 days at least, so a clip survives a weekend before loop-over.
Event-lock reserve15%15 percent of the card stays reserved for locked clips: 71.4 GB on this card. Loop recording cannot use it.

The figures

FigureValueNote
Total bitrate62 Mbps4K front at 50 Mbps plus 1 more channel at 12 Mbps each.
Storage per driving hour27.9 GBTotal bitrate x 0.45 GB per hour per Mbps.
Driving storage per day223.2 GB8 driving hours at 27.9 GB an hour.
Total storage per day223.2 GBDriving plus parking, every day the camera runs.
Usable space on the 512 GB card404.7 GBCard size x 0.93 for formatting, minus the 15 percent event reserve.
Hours of footage the card holds14.5 hoursUsable space divided by GB per driving hour.
Days before loop-over1.8 daysUsable space divided by GB per day.
Card size needed for 3 days847.1 GBGB per day x 3 days, grossed up for formatting plus the event reserve.
Recommended card1 TBSmallest standard size at or above the space needed.
Full-card rewrites per year159GB written per year divided by card size. Bigger cards rewrite less often, so they last longer.

What to do

  • Move to a 1 TB card. It is the smallest size that holds 3 days at these settings.
  • Switch the codec to H.265 if your camera offers it. The same 512 GB card then holds about 3.6 days.
  • Drop the front camera to 2K. The same 512 GB card then holds about 3 days.
  • Or keep the 512 GB card and pull any clip you need within 1 day, before loop-over erases it.
  • Your camera tops out at 512 GB, so a bigger card is not an option. The fix is a lower bitrate, not a bigger card.

Notes

  • Bitrates here are typical values from Nexar guidance for default quality at 30 fps. Real bitrate varies by camera, firmware, quality setting, plus scene. Check the manual for the exact bitrate, or measure it from file sizes: Mbps is about file size in MB x 8 divided by seconds.
  • H.265 cuts file sizes to about half at equal quality, per Nexar guidance. If your camera offers it, the H.265 setting doubles the days a card holds.
  • Locked event clips are never overwritten. If the event folder fills up, some cameras stop saving new events, others overwrite the oldest locked clip. Clear locked clips you no longer need.
  • Use a high-endurance microSD card rated for continuous recording, U3 plus V30 speed class. Format it in the camera every month or two. Standard cards wear out fast under loop recording.

This calculator uses typical bitrates from Nexar guidance for default quality at 30 fps. Check your camera manual for its exact bitrate plus largest supported card.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This calculator gives estimates from typical bitrates. Real file sizes vary by camera, firmware, plus settings — check your camera manual for its exact bitrate plus largest supported card.

Quick answer: A 4K front plus 1080p rear dash cam writes about 27.9 GB an hour at default quality, so a 512 GB card holds under two days of 8-hour driving before loop-over starts. A 1080p single camera writes 5.4 GB an hour, so the same card holds about nine days. The size you need comes from three numbers: total bitrate, driving hours a day, plus the days you want to keep. This calculator works out the card size plus the days before loop-over for 1080p, 2K, plus 4K setups with one to four channels.

Last reviewed: · Focus keyword: dash cam storage calculator

How much storage does a dash cam need?

A dash cam needs enough card space to hold the footage you want to keep before loop-over erases the oldest clips. The size comes from three numbers: the total bitrate of every channel, the hours you drive each day, plus the days of footage you want to keep. Multiply those three, then gross the result up for formatting plus the space the camera keeps for locked event files. That grossed-up number is the card size to buy.

Take the most common truck setup: a 4K front camera plus a 1080p rear camera, the layout of the best-selling ROVE R2-4K Dual. The front channel runs about 50 Mbps at default quality, the rear about 12 Mbps, for a total of 62 Mbps. Each megabit per second uses about 0.45 GB an hour, so the pair writes 27.9 GB an hour. Eight hours of driving makes 223.2 GB a day. Three days makes 669.6 GB of footage. Formatting takes about 7 percent of a card, plus the camera keeps about 15 percent for locked event files, so the card you need is 847.1 GB. The smallest standard size that covers it is a 1 TB card.

Now take the same three days on a single 1080p front camera. One channel at 12 Mbps writes 5.4 GB an hour, 43.2 GB a day, 129.6 GB over three days. Grossed up the same way, the card you need is 163.9 GB, so a 256 GB card covers it with room to spare. Same three days, same driving hours, one quarter of the card. Resolution plus channel count decide the answer, not the brand on the box.

Most buyers guess wrong in the same direction: too small. The card in the box makes it worse. The ROVE R2-4K Dual ships with a 128 GB card, which sounds generous until the math lands: at 4K front plus 1080p rear it holds 3.6 hours of driving, less than half a working day. The included card gets the camera running on day one. It is not a storage plan. Run the numbers before you buy the card, not after the clip you need is gone.

The retention target matters as much as the setup. Three to five days is a sensible minimum. A clip from Friday must survive the weekend. A claim, a complaint, or a request for footage can surface days after the drive, not minutes. Dash cam footage is also the evidence that decides a crash dispute: the Crash Preventability Checker runs the challenge that video evidence supports. The Post-Accident Testing Decision Tool covers the testing steps that follow a crash. A card that loops every day can erase the clip before anyone asks for it.

SetupTotal bitrateGB per hourGB per 8-hour day
1080p front only12 Mbps5.443.2
1080p front plus rear24 Mbps10.886.4
2K front only25 Mbps11.390.0
2K front plus 1080p rear37 Mbps16.7133.2
4K front only50 Mbps22.5180.0
4K front plus 1080p rear62 Mbps27.9223.2
4K front plus 3 more at 1080p86 Mbps38.7309.6
4K front plus 3 more at 2K125 Mbps56.3450.0

H.264, 30 fps, default quality. Bitrates from Nexar guidance, verified 19 Nov 2026. H.265 halves these figures. 60 fps adds about 50 percent.

How many GB per hour does a dash cam use?

Bitrate decides file size, not resolution. A 4K camera recording at 20 Mbps writes smaller files than a 2K camera recording at 40 Mbps. The 2K footage looks better doing it, because each pixel gets more data. Dash cam maker Nexar makes the point bluntly: a 4K label on the box says nothing about how much detail the camera keeps. The bitrate does. Two cameras with the same resolution on the spec sheet can fill the same card at very different rates.

Nexar publishes minimum bitrates for clean footage at each resolution: 12 to 15 Mbps for 1080p, 25 to 30 Mbps for 1440p, 50 to 60 Mbps for 4K with H.264. Below 10 Mbps at 1080p, compression artifacts show under normal driving conditions. This calculator uses the low end of each Nexar range: 12, 25, plus 50 Mbps. Those are default-quality figures. A camera set to maximum quality runs higher. The VIOFO A229 Pro records its 4K front channel at 57 Mbps. The older A129 Pro tops out at 60.3 Mbps. A camera set to low quality runs lower. The footage shows it.

Channels add up. Each channel writes its own stream to the same card, so a dual camera writes roughly double a single camera at the same resolution. A four-channel setup writes roughly four times as much. A 4K front plus 1080p rear pair totals 62 Mbps. A four-channel rig with a 4K front plus three 2K channels totals 125 Mbps, which is 56.3 GB an hour. That is why multi-channel truck cameras, the growing segment for blind-spot coverage, need the biggest cards on the market.

Frame rate moves the number too. Going from 30 fps to 60 fps adds about 50 percent to storage. A 4K front plus 1080p rear setup jumps from 27.9 GB an hour to about 41.9 GB an hour. Sixty frames helps with fast-moving plates, but it costs half again as much card for the same retention. Most truckers are better served by 30 fps plus a bigger card than by 60 fps plus a card that loops every day.

The most accurate bitrate is your own camera, not a table. Copy a one-minute clip off the card and do the arithmetic: file size in MB times 8, divided by seconds, gives approximate Mbps. A one-minute 4K clip of about 300 MB works out to about 40 Mbps. A one-minute 1080p clip of about 63 MB works out to about 8 Mbps. Measure a few clips from different drives, because variable bitrate changes with the scene: a busy highway at dusk writes more data than an empty road at noon. Use the highest figure you measure for planning, not the average.

ResolutionNexar minimum (H.264)Engine valueH.265 equivalentGB per hour
1080p Full HD12 to 15 Mbps12 Mbps6 Mbps5.4
2K QHD (1440p)25 to 30 Mbps25 Mbps12.5 Mbps11.3
4K UHD (2160p)50 to 60 Mbps50 Mbps25 Mbps22.5

Nexar minimums published 2 Apr 2026. Engine values are the low end of each range at 30 fps, default quality. GB per hour is one channel at the engine value.

What size SD card do I need for a dash cam?

Start from the days you want to keep, not from the card sizes on the shelf. Three days of 8-hour driving is the worked example through this page. A single 1080p camera needs 163.9 GB of card space for three days, so a 256 GB card covers it. A 2K front plus 1080p rear setup needs 505.5 GB, so a 512 GB card covers it, barely. A 4K front plus 1080p rear setup needs 847.1 GB, so only a 1 TB card covers it. A four-channel 4K rig needs more than any card on the market for three days, which means the answer is a lower bitrate or a shorter target, not a bigger card.

The camera limit is the trap inside the answer. Many dash cams cap the card size they accept. A card above the cap either fails to format or formats down to a size the camera understands. The original ROVE R2-4K tops out at 512 GB. The newer R2-4K Dual takes cards up to 1 TB. BlackVue cameras support up to 512 GB. Check the manual for your exact model before you buy, because the limit varies by model, not by brand. This calculator asks for the largest card your camera supports and flags the result when the card you need is bigger than the card your camera takes.

Bigger cards also last longer, which matters more than it sounds. A card wears out by rewriting: every gigabyte written eats a little of the flash memory. A 4K dual setup writing 223.2 GB a day rewrites a 128 GB card about 636 times a year, a 256 GB card about 318 times, a 512 GB card about 159 times, plus a 1 TB card about 80 times. The same footage, the same camera, four times the life from the bigger card, because the wear spreads over four times as many memory cells. Buy the biggest card the camera supports if the budget allows. The calculator shows full-card rewrites per year for exactly this reason.

If no card fits the target, change the target or the bitrate. Switching the codec to H.265 halves the space a setup needs, so a 4K dual rig that needs 847.1 GB for three days needs 423.5 GB on H.265, which a 512 GB card covers. Dropping the front camera from 4K to 2K cuts the need from 847.1 GB to 505.5 GB, which a 512 GB card also covers. Shortening the target from three days to two cuts the need by a third. Any one of those moves turns an impossible card size into a card you can buy.

SetupCard space for 3 daysSmallest card
1080p front only163.9 GB256 GB
1080p front plus rear327.9 GB512 GB
2K front only341.6 GB512 GB
2K front plus 1080p rear505.5 GB512 GB
4K front only683.1 GB1 TB
4K front plus 1080p rear847.1 GB1 TB
4K front plus 3 more at 1080p1,175.0 GBOver 1 TB
4K front plus 3 more at 2K1,707.8 GBOver 1 TB

Eight driving hours a day, 15 percent event reserve, H.264 at 30 fps. Card space is grossed up for formatting plus the event reserve.

How long does a 128GB card last in a dash cam?

A 128 GB card is the size most often in the box. It is also the size most buyers already own. What it holds depends entirely on the setup. A single 1080p camera gets 18.7 hours from it, about two full driving days. A 2K front plus 1080p rear setup gets 6.1 hours, not even one driving day. A 4K front plus 1080p rear setup gets 3.6 hours, less than half a driving day. A four-channel 4K rig gets under two hours. The same card, the same 128 GB label, a tenfold spread in what it actually holds.

Loop recording is what makes those hours a window, not a limit. When the card fills, the camera overwrites the oldest unprotected footage first and keeps recording. Recording never stops for a full card. The hours in the table are how far back the window reaches: a 4K dual camera on a 128 GB card always holds the last 3.6 hours of driving, no more. Footage older than that is gone, whether anyone looked at it or not.

That window is the number that decides whether a clip survives. A morning incident on a 4K dual camera with a 128 GB card is overwritten by the early afternoon if the truck keeps rolling. The same incident on a 1080p single camera survives into the day after tomorrow. The fix is not complicated: pull any clip you need the same day, or buy the card the retention target actually needs. A clip saved to a phone or a laptop is safe from loop-over forever.

After a crash, the window matters most. Save the footage before the truck moves again, because every mile of driving after the incident pushes the oldest footage closer to erasure. The Post-Accident Testing Decision Tool covers the testing steps that follow a crash. The DataQs Challenge Helper covers challenging a violation with the video evidence the camera kept. Both jobs need the clip. A card that loops in hours can lose it before the paperwork starts.

SetupHours on 128 GBDays at 8 hours a day
1080p front only18.72.3
1080p front plus rear9.41.2
2K front only9.01.1
2K front plus 1080p rear6.10.8
4K front only4.50.6
4K front plus 1080p rear3.60.5
4K front plus 3 more at 1080p2.60.3
4K front plus 3 more at 2K1.80.2

H.264, 30 fps, default quality, 15 percent event reserve. Usable space on a 128 GB card is about 101.2 GB.

How does parking mode affect dash cam storage?

Parking mode keeps the camera watching while the truck is parked. A 10-hour overnight break can add more footage than the driving day. How much it adds depends on the mode. Time-lapse records one frame per second and plays it back fast. Low bitrate records continuously at a reduced bitrate. Motion detection records at full rate whenever motion triggers it. The three modes differ by a factor of ten in storage, so the mode matters as much as the hours.

Time-lapse is the storage-friendly option. It records about 5 percent of the data of full-rate recording, because one frame per second carries far less information than thirty. BlackVue rates its dual-channel time-lapse at about 110 hours on a 64 GB card at the highest quality setting, which works out to about 0.5 GB an hour. A 10-hour night at that rate uses about 5 GB on a dual 1080p setup, or about 14 GB on a 4K dual setup. The trade-off is detail: one frame per second catches a person walking up to the truck, but it can miss a fast event between frames. Most cameras switch to full-rate recording the moment the G-sensor feels an impact, so the impact itself is still caught at full quality.

Low bitrate parking records continuously at about a quarter of the driving rate. A 10-hour night uses about 14 GB on a 1080p single camera, or about 70 GB on a 4K dual setup. The footage is continuous, so nothing falls between frames, but the picture is softer than driving footage. It is the middle option: more storage than time-lapse, more complete coverage than motion detection.

Motion detection is the unpredictable option. It records at full rate whenever the camera sees motion. It records nothing when the scene is still. In a quiet lot it uses almost nothing. In a busy truck stop, where trucks, reefers, plus people move all night, it can run near the full driving rate for hours. This calculator plans motion detection at half the driving rate, which is a planning assumption, not a promise. A night in a packed lot can use far more. If the retention math is tight, time-lapse is the predictable choice.

Parking mode has a power cost as well as a storage cost. Most cameras need a hardwire kit to run parking mode. The kit draws on the truck batteries all night. A camera plus a fridge plus an inverter sharing one battery bank during a 10-hour break is a power budget, not a single device. The Inverter Size Calculator for Trucks sizes the inverter plus cable for the whole cab load, the Truck Fridge Power Calculator works out whether the battery survives the break with a fridge running. The Jump Starter Size Checker covers the backup for a morning when the batteries went flat overnight.

Parking modeRate vs drivingGB per 10-hour night, 1080p singleGB per 10-hour night, 4K dual
Time-lapse 1 fpsAbout 5 percent2.714.0
Low bitrateAbout 25 percent13.569.8
Motion detectionAbout 50 percent27.0139.5
Full rate, for comparison100 percent54.0279.0

Parking factors are planning assumptions. Motion detection varies with how busy the parking spot is. Time-lapse at 5 percent reproduces the BlackVue published figure of about 110 hours on a 64 GB card for a dual 1080p setup.

Why do event-locked clips eat your card space?

A dash cam locks a clip when the G-sensor feels a bump, or when the driver presses the event button. Locked clips go into a protected folder that loop recording cannot touch. That protection is the point: the clip from a hard brake or a collision survives even when the card fills and loops. It is also a cost. Every locked clip sits on the card permanently, taking space the loop can never reuse.

Most cameras set aside 10 to 30 percent of the card for locked event files. That space is not available for loop recording. This calculator defaults to 15 percent. On a 512 GB card, 15 percent is about 71 GB reserved for locked clips, on top of the 7 percent formatting takes. The usable space left for loop recording is about 404.7 GB, not 512 GB. The gap between the label and the usable space surprises buyers who did the math on the full number.

Rough roads fill the folder fast. A G-sensor set too sensitive locks a clip for every pothole, every dock bump, plus every rough stretch of interstate. A truck that runs rough lanes can fill the event folder in weeks, all with clips nobody will ever watch. Turn the G-sensor sensitivity down a notch. Check the event folder when you check the card. Delete locked clips you no longer need. The space comes back for loop recording the moment they are gone.

When the event folder fills up, the protection fails quietly. Some cameras stop saving new events. Others overwrite the oldest locked clip, which defeats the purpose of locking it. Either way the driver gets no warning worth the name. The habit that prevents it is simple: clear the event folder every month, at the same time you format the card. Keep the clips that matter on a phone or a laptop, where loop-over cannot reach them.

The reserve is also why two identical cards can hold different amounts of driving. A camera with the event reserve set to 30 percent holds noticeably less loop footage than the same camera set to 10 percent. The calculator lets you set the reserve so the days it shows match what the card actually holds. If the manual does not state the reserve, 15 percent is the middle of the usual range.

Does H.265 really halve dash cam file sizes?

On paper, yes. Dash cam maker Nexar says 4K footage needs 50 to 60 Mbps with H.264, but only about 25 to 30 Mbps with H.265, for the same quality. That is about half the bitrate, which means about half the storage. This calculator counts H.265 at half the H.264 bitrate, following that guidance. The payoff is large: a 4K front plus 1080p rear setup on a 512 GB card goes from 1.8 days of retention to 3.6 days, just by switching the codec.

In practice, the saving is often smaller. Measured dash cam tests show H.265 saving less than half on real cameras. The VIOFO A129 Pro at its maximum setting records the 4K front channel at 60.3 Mbps in H.264, against 52.4 Mbps in H.265, a saving of about 13 percent. At the medium setting the saving is about a quarter: 30.3 Mbps against 22.4 Mbps. The codec is more efficient, but the camera firmware does not always spend that efficiency on smaller files. It often spends it on better quality at a similar file size.

The gap comes from how makers set bitrates. A codec setting is a target, not a guarantee. Firmware caps differ between models. One camera H.265 mode may run at half the H.264 bitrate. Another may run at 90 percent of it with visibly better detail. The manual rarely states the H.265 bitrate at all, which is why the honest answer is a range, not a single number. This calculator treats the H.265 result as the optimistic end. If the camera saves less, the card holds fewer days than the H.265 result shows.

Compatibility is the other check before switching. Most current phones, computers, plus players handle H.265 files without trouble. Older players and older phones may struggle or refuse to open them. Check that the devices you use to review footage can play H.265 before you switch the camera over, or the first time you need a clip in a hurry is the wrong time to discover the player cannot open it.

The decision is simple either way. If the camera offers H.265 and the playback devices handle it, switch it on. The storage saving is real even at the measured end. The retention gain is the cheapest card upgrade available: no new card, no new camera, just a setting. If the camera does not offer H.265, the setting does not exist. The card size has to do the work instead.

What SD card should I buy for a dash cam?

Buy a high-endurance card, not a standard one. A dash cam writes to its card every second it runs, then overwrites the same card again and again as the loop turns. That workload wears standard flash memory out fast. High-endurance cards use tougher NAND flash plus wear-leveling that spreads writes across the memory cells. They carry ratings for continuous recording. The Samsung PRO Endurance 256 GB card is maker-rated to 140,160 hours of recording on a looped 1080p lab workload. The SanDisk Max Endurance 256 GB card is maker-rated to 120,000 hours. Both are rated to run from minus 25 C to plus 85 C, which matters on a windshield in summer.

Speed class matters next. Look for U3 plus V30 on the label, which guarantees sustained writes of 30 MB per second. A 4K front plus 1080p rear setup averages about 8 MB per second, so V30 gives comfortable headroom over the average plus room for peak writes when the scene gets busy. A slower card can drop frames or corrupt clips when the camera writes faster than the card accepts. The card is not the place to save money. A dropped clip is a missing clip.

Capacity is endurance, as the rewrites figure shows. A bigger card spreads the same daily writes over more memory cells, so each cell rewrites less often and the card lasts longer. A 512 GB card in a 4K dual setup rewrites about 159 times a year. A 128 GB card in the same setup rewrites about 636 times a year. The bigger card costs more once and lasts far longer. Buy the biggest card the camera supports if the budget allows.

Format the card in the camera, not on a computer. In-camera formatting sets the file system plus folder layout the camera expects. It clears the file allocation table so the controller can reallocate weak memory blocks. Format a new card before first use, then format again every month or two. Copy any clips you want to keep before formatting, because formatting erases everything, including locked event files.

Buy from a seller you trust. Counterfeit cards are common online. A fake card fails exactly where a dash cam stresses it hardest: sustained writes, heat, plus constant overwriting. A card that tests fine on a first write can corrupt footage weeks later. If the price looks too good for the capacity, it usually is. A dash cam is only as reliable as the card inside it.

A dash cam is one item in a new driver setup, not the whole list. The New Trucker Gear Cost Estimator prices the full starter kit, dash cam plus fridge plus inverter plus straps plus chains plus the rest, in budget, mid, plus premium tiers, so the card size decision sits inside the real total.

How do you use the Dash Cam Storage Calculator?

Work through the fields in order. The calculator updates with every change, so you can fix an answer and watch the verdict change.

  1. Pick the front camera resolution plus the number of channels.
  2. Pick the codec plus frame rate your camera uses.
  3. Enter driving hours per day plus the days of footage to keep.
  4. Pick the card size you own or plan to buy.
  5. Pick the largest card your camera supports.
  6. Add parking mode plus hours if the camera records while parked, then read the verdict, the card size, plus the days before loop-over.

Before you buy a card on a result, check the camera manual for its exact bitrate plus largest supported card. The calculator uses typical bitrates for default quality. A camera set to maximum quality writes more. The manual states the limit the calculator can only ask you to enter.

Frequently asked questions

How much storage does a 4K dash cam need?

A 4K front plus 1080p rear dash cam writes about 27.9 GB an hour at default quality, so three days of 8-hour driving needs about 847 GB of card space. A 1 TB card is the smallest size that covers it. A 4K front-only camera needs about 683 GB for the same three days, so it also needs a 1 TB card. Switching the codec to H.265 halves both numbers.

How many hours of footage does a 128GB card hold?

It depends on the setup. A single 1080p camera gets about 18.7 hours from a 128 GB card. A 2K front plus 1080p rear setup gets about 6.1 hours. A 4K front plus 1080p rear setup gets about 3.6 hours. A four-channel 4K rig gets under two hours. All figures assume H.264 at 30 fps with a 15 percent event reserve.

What does loop recording mean?

Loop recording means the camera overwrites the oldest unprotected footage when the card fills, so recording never stops. The card holds a window of recent driving, not an archive. Locked event clips are protected from overwriting and stay on the card until deleted. The window length is the usable card space divided by the GB written per day.

Does parking mode use a lot of storage?

It depends on the mode. Time-lapse at 1 fps uses about 5 percent of the driving rate, so a 10-hour night costs about 14 GB on a 4K dual setup. Low bitrate parking uses about a quarter of the driving rate, about 70 GB for the same night. Motion detection uses about half the driving rate on average, about 140 GB, but in a busy truck stop it can run near the full rate all night.

Why does my dash cam say the card is full?

The usual cause is locked event files. The G-sensor locks a clip after every bump. Locked clips sit in a protected folder that loop recording cannot touch. When the folder fills, the camera reports the card as full even though loop footage keeps turning over. Turn the G-sensor sensitivity down, delete locked clips you no longer need, plus format the card in the camera every month or two.

Should I use H.265 on my dash cam?

Yes, if the camera offers it and the devices you use to review footage can play H.265 files. Nexar guidance puts H.265 at about half the bitrate of H.264 for equal quality, so a 512 GB card on a 4K dual setup holds about 3.6 days instead of 1.8. Measured savings on some cameras are smaller, about a quarter at medium settings, so treat the H.265 result as the optimistic end.

Related tools

Sources

Follow on WhatsApp Ask by Voice