Size for what runs at the same time. Tick every appliance you run together. The calculator works out the inverter size, the starting surge, the cable gauge, plus how fast the load drains your batteries. A microwave counts at its input watts, not the cooking watts on the box.
Tick the loads you run together. Every answer updates the result as you change each field.
Your AC appliances (through the inverter)
Your 12V loads (straight off the battery, no inverter)
Your battery bank
Cable run and parked hours
You need a 2,000W pure sine wave inverter.
2,000W pure sine wave, 4,000W surge rating.
Your loads total 1,260W running. Add 25 percent headroom and the next standard size up is 2,000W continuous, with a 4,000W surge rating that covers the 1,692W starting surge. At full load the inverter pulls 127.3 amps from the batteries.
The checks
| Check | Result | Detail |
|---|---|---|
| Inverter size | 2,000W | 1,260W running plus 25 percent headroom, rounded up to the next standard size. |
| Starting surge | 1,692W | Covered by the 4,000W surge rating of a 2,000W unit. |
| Waveform | Pure sine | At least one picked appliance needs pure sine wave power. A modified sine unit can damage it. |
| Battery at full load | 1.6 hours | Everything on empties the usable capacity in about an hour. Run big loads with the engine on. |
| 10-hour parked break | Survives | Overnight loads use 126 Ah of 200 Ah usable. |
| Cable and fuse | 1/0 AWG | 175A fuse at the battery. Copper cable, 3 percent maximum voltage drop. |
The figures
| Figure | Value | Note |
|---|---|---|
| Total running watts | 1,260W | All checked AC loads running at once. |
| Starting surge | 1,692W | Largest motor starting while the rest run. |
| Recommended inverter | 2,000W continuous | Running watts plus 25 percent headroom, next standard size up. |
| Surge rating | 4,000W | Standard surge rating is twice the continuous rating. |
| Battery draw at full load | 127.3A | AC watts divided by 12 volts divided by 0.85 efficiency, plus DC loads. |
| Battery draw per hour | 127.3 Ah | One hour at full load uses this many amp-hours. |
| Usable battery capacity | 200 Ah | 400 Ah nominal at 50 percent usable depth of discharge. |
| Runtime at full load | 1.6 hours | Usable capacity divided by full-load draw. |
| Overnight draw | 12.6A | Loads that run while you sleep. |
| 10-hour parked break | 126 Ah | Overnight draw times parked hours. |
| Cable gauge, battery to inverter | 1/0 AWG | Copper cable, 3 percent maximum voltage drop. |
| Fuse at the battery | 175A | 125 percent of maximum draw, next standard size up. |
What to do
- Buy pure sine wave. A modified sine unit can trip a CPAP, cook a microwave slowly, or damage sensitive electronics.
- Mount the inverter close to the batteries and run 1/0 AWG copper cable, fused at the battery with a 175A fuse.
- Run the microwave, kettle, or heater with the engine running. The alternator covers the draw and the batteries stay full.
Notes
- Microwave watts on the box are cooking watts. The input draw is about 1.5 times higher: a 700W microwave draws about 1,080W.
- Inverter efficiency is about 85 percent. That loss comes straight out of the batteries as extra amps.
- Usable capacity is 50 percent of the nominal rating. Draining lead acid deeper shortens its life fast.
This calculator sizes an inverter from the loads you pick, using input watts for microwaves, 85 percent inverter efficiency, plus 25 percent headroom. Check the label on each appliance and confirm the install with a qualified technician before you buy.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not professional electrical advice — have a qualified technician check the install before you rely on a result.
Quick answer: Most solo drivers need a 2,000W pure sine wave inverter. That covers a 700W microwave, a CPAP machine, plus a laptop running together. Add up the running watts of everything you use at the same time, add 25 percent headroom, then round up to the next standard size. Size the microwave on its input watts, about 1,080W for a 700W model, not the cooking watts on the box. This calculator does the full sum: running watts, starting surge, pure vs modified sine wave, cable gauge, fuse size, plus battery draw per hour.
What size inverter do I need for my truck?
The answer depends on the biggest combination of appliances you run at the same time, not on the longest list of things you own. A driver who charges a phone plus a laptop needs a 300W inverter. A driver who heats a meal in the microwave while the CPAP waits for the night needs a 2,000W inverter. A team running two microwaves plus a cooktop needs a 5,000W inverter, or two separate inverters. The calculator on this page sizes the inverter from your own list, so the answer fits your cab instead of a generic chart.
Three rules drive every answer. First, size on running watts plus 25 percent headroom. An inverter run at its full rating all day runs hot plus dies early. Second, check the starting surge. Motors plus transformers pull extra power for a second at start. The inverter surge rating, usually twice the continuous rating, must cover it. Third, size the microwave on input watts. The number on the front of a microwave is cooking power. The power it pulls from the outlet is about 1.5 times higher.
The table below shows the usual answers for common cab setups. Standard inverter sizes run 300W, 500W, 1000W, 1500W, 2000W, 2500W, 3000W, 4000W, plus 5000W. Every row rounds up to the next standard size after the 25 percent headroom is added.
| What runs together | Running watts | Inverter size |
|---|---|---|
| Phone charging plus a laptop | 150W | 300W |
| CPAP plus laptop plus LED TV | 230W | 300W |
| CPAP plus laptop plus 700W microwave | 1,260W | 2,000W |
| CPAP plus laptop plus 1000W microwave | 1,720W | 2,500W |
| 700W microwave plus kettle plus CPAP | 2,170W | 3,000W |
| Team cab: two microwaves plus cooking | 3,500W | 5,000W |
The 2,000W to 3,000W range is the standard recommendation for sleeper cabs. The table shows why. A single microwave already pulls over 1,000W of input power. Add a CPAP plus a laptop and the total passes 1,200W, which needs a 2,000W unit after headroom. Drivers who cook with an induction cooktop or run a space heater should expect 3,000W or more. Drivers who only charge devices plus run a CPAP can save money with a 500W or 1000W unit, as long as nothing bigger ever joins the list.
One warning applies to every row: the surge rating on the box is not the size. A unit sold as 4,000W peak may only deliver 2,000W continuous. Size on the continuous rating, which is the smaller number in the listing. The calculator checks the surge rating separately, so a big starting surge can push the recommendation up even when the running watts look small.
How do you use the Inverter Size Calculator for Trucks?
The calculator works from the loads you pick, not from a guess about your cab. Tick the appliances you run together, tell it about your battery bank, then read the verdict. The steps below match the tool at the top of the page.
- Tick every AC appliance you run at the same time.
- Add any other AC appliance in the custom watts box.
- Tick your 12V loads, which run straight off the battery.
- Enter your battery bank: battery count, amp-hours each, plus battery type.
- Pick the cable run length plus the parked hours to check.
- Read the verdict, the cable gauge, the fuse size, plus the battery draw.
The result shows six checks: inverter size, starting surge, waveform, battery at full load, the parked break, plus cable and fuse. Below the checks, the figures table lists every number the calculator used, so you can see the running watts, the surge watts, the DC amps, the usable battery capacity, plus the overnight draw. The copy button saves the whole summary as text.
Two inputs change the answer most. The appliance list sets the inverter size. The battery bank sets the runtime verdict. If the parked break fails, the fix is usually a bigger bank, a lithium upgrade, or one less overnight load, not a bigger inverter. An inverter cannot fix a battery bank that is too small for the night.
Why does a 700W microwave need a 2000W inverter?
Because the 700W on the box is cooking power, not electrical draw. A microwave turns about 65 percent of the electricity it pulls into cooking energy. The rest becomes heat in the magnetron plus the transformer. Divide 700W by 0.65 and the real input draw is about 1,080W. That is the number the inverter must supply, before any other appliance joins in.
The gap surprises most buyers. Some guides make it worse by quoting the cooking watts as if they were the draw. One figure repeated in roundups puts a 700W to 1000W microwave at 60 to 85 amps at 12V. That arithmetic divides cooking watts by 12 volts, which skips both the input loss and the inverter loss. The true draw at 12V, with 85 percent inverter efficiency, is about 106 amps for a 700W microwave plus about 151 amps for a 1000W microwave. This calculator uses input watts throughout, so its battery figures run higher than the roundup numbers. They are the honest ones.
Three more steps turn 1,080W into a 2,000W recommendation. First, the microwave surges at start. A 700W cooking microwave pulls about 1,400W for a second while the transformer magnetizes. Second, add 25 percent headroom: 1,080W times 1.25 is 1,350W, which rounds up to a 1,500W inverter for the microwave alone. Third, add anything else running at the same time. A CPAP at 90W plus a laptop at 90W bring the total to 1,260W. 1,260W times 1.25 is 1,575W, which rounds up to 2,000W. That is why the 2,000W unit is the usual pairing for a cab with a microwave.
| Microwave cooking watts | Input draw | DC amps at 12V | Inverter, microwave alone |
|---|---|---|---|
| 600W | 920W | 90A | 1,500W |
| 700W | 1,080W | 106A | 1,500W |
| 1000W | 1,540W | 151A | 2,000W |
| 1200W | 1,850W | 181A | 2,500W |
The label on the back of the microwave beats every estimate here. It lists input watts or input amps. If it lists amps, multiply by 120 to get watts. A compact truck microwave rated 700W cooking often lists about 1,050W to 1,150W of input power, which matches the table. If your label reads higher, type the label figure into the custom watts box and let the calculator size from the real number.
Pure sine wave vs modified sine wave: which appliances need pure sine?
A pure sine wave inverter copies the smooth wave of grid power. A modified sine wave inverter builds a blocky stepped wave that approximates it. Simple heating loads do not care about the difference. Motors, compressors, medical devices, plus sensitive electronics do. On a stepped wave they run hotter, hum louder, lose efficiency, or refuse to start at all.
The quality gap is measurable. A good pure sine inverter holds total harmonic distortion under 3 percent, on par with utility power. A modified sine inverter typically runs 20 to 45 percent distortion, which means a large share of the delivered energy sits in harmonics the appliance never expected. That extra energy turns into heat in motor windings plus transformer cores, which shortens the life of the appliance even when it seems to work.
The rule for a truck cab is simple: if any appliance on your list needs pure sine, buy pure sine. The price gap over modified sine is small at truck sizes. One damaged CPAP machine costs far more than the difference. The calculator flags the waveform for every appliance you tick, so the verdict follows your own list.
| Appliance | Modified sine wave | Verdict |
|---|---|---|
| CPAP machine, medical devices | Not recommended | Pure sine required |
| Microwave oven | Unreliable, cooks slowly | Pure sine required |
| Induction cooktop | May not start | Pure sine required |
| Compressor fridge, variable speed motors | Runs hot, shortens life | Pure sine required |
| Laptop, TV, game console, chargers | Usually works, runs warm | Pure sine recommended |
| Kettle, coffee maker, heater, blanket | Runs fine | Modified sine is fine |
Two cases deserve a closer look. A CPAP machine with a heated humidifier is the most sensitive load in a cab: the power supply can trip, the pressure can drift, plus the humidifier control can go unstable on a stepped wave. Sleep apnea treatment is not the place to test a cheap inverter. A microwave is the other one: on modified sine it cooks slowly, buzzes loudly, plus risks magnetron damage over time. Since a microwave is the reason most drivers buy a big inverter, the waveform decision is usually made the moment the microwave goes on the list.
Resistive loads are the exception that proves the rule. A kettle, a drip coffee maker, a space heater, plus an electric blanket turn electricity into heat through a simple element. The wave shape does not matter to an element. If your whole list is resistive, a modified sine inverter saves money with no real penalty. The moment one electronic or motor load joins the list, pure sine becomes the right buy.
What cable size do I need for my inverter?
Cable size follows the DC amps, not the AC watts. A 2,000W inverter pulls about 196 amps from a 12V bank at full load, because the same power at one tenth of the voltage needs ten times the current, plus the inverter loses about 15 percent in conversion. That current needs thick copper cable. Thin cable overheats, drops voltage, plus can melt its insulation. The cable run between the battery plus the inverter is the most dangerous part of the install, which is why the calculator sizes it from your own numbers.
The table below gives the minimum copper gauge for a short run, under 5 feet one way, at a 3 percent maximum voltage drop. Longer runs need thicker cable: a 5 to 10 foot run goes one size up, a 10 to 15 foot run goes two sizes up. Measure the run one way, from the battery to the inverter. Remember the current travels both ways, so the round trip is twice that distance.
| Maximum DC amps | Cable gauge, short run | Typical inverter |
|---|---|---|
| 30A | 8 AWG | 300W |
| 50A | 6 AWG | 500W |
| 100A | 2 AWG | 1000W |
| 150A | 1/0 AWG | 1500W |
| 200A | 2/0 AWG | 2000W |
| 300A | 4/0 AWG | 3000W |
| Over 300A | Dual 2/0 AWG runs | 4000W plus |
Worked example: a 2,000W inverter at full load draws 2,000 divided by 12 divided by 0.85, which is 196 amps. That lands in the 200A row, so the cable is 2/0 AWG copper on a short run. The fuse is 125 percent of 196 amps, which is 245 amps, rounded up to the next standard size, a 250A fuse. The fuse sits at the battery end of the positive cable, within a short distance of the terminal, so a short anywhere along the run blows the fuse instead of starting a fire.
Three cable mistakes repeat in truck installs. First, the cable supplied in the box is often too thin for a 2,000W or bigger unit. Check the gauge printed on the jacket against the table. Replace the supplied cable if it falls short. Second, copper clad aluminum cable looks like copper but carries less current for the same gauge. Buy pure copper cable, marked OFC or bare copper, from a known supplier. Third, loose or corroded terminals heat up under load even when the cable itself is right. Check the connections during your pre-trip inspection. Look for discoloration or melted insulation at the lugs.
Mount the inverter as close to the batteries as the install allows. Every extra foot of cable adds resistance plus voltage drop, which is why the long-run column in the calculator pushes the gauge up so fast. A short, thick run with a fuse at the battery is the safest install shape. It is also the cheapest, because thick copper cable is priced by the foot.
How fast will an inverter drain my truck batteries?
Faster than most drivers expect. The math is simple: battery draw in amps equals AC watts divided by 12 volts divided by 0.85 efficiency. A 1,000W load pulls about 98 amps. A 2,000W load pulls about 196 amps. A typical Class 8 bank holds four Group 31 batteries at 100 amp-hours each, which is 400 amp-hours nominal, but only about 200 amp-hours is usable, because draining lead acid below half its charge shortens its life fast.
The table below shows full-load runtime on that standard bank: four Group 31 batteries, 400 amp-hours nominal, 200 amp-hours usable. Runtime is usable capacity divided by draw. Real driving mixes heavy loads with light ones, so a microwave used for five minutes costs far less than an hour at full load. The table shows the worst case, everything on, engine off.
| AC load | Battery draw | Runtime, 200 Ah usable |
|---|---|---|
| 300W | 29A | 6.8 hours |
| 1000W | 98A | 2.0 hours |
| 1,260W | 127A | 1.6 hours |
| 2000W | 196A | 1.0 hours |
| 3000W | 294A | 0.7 hours |
Two battery facts matter more than the headline capacity. First, usable capacity depends on chemistry. Flooded plus AGM lead acid give about 50 percent of the nominal rating before damage starts. Lithium iron phosphate gives about 80 percent, so a 400 amp-hour lithium bank offers 320 usable amp-hours against 200 for lead acid. That is why the calculator asks for battery type. Second, starter batteries are built to crank, not to cycle. Deep discharges wear them out in months. A separate deep-cycle house bank, isolated from the starter bank, is the proper setup for heavy overnight inverter use.
The overnight question is the one that strands drivers. A CPAP plus a 12V fridge draw about 12.6 amps together, which is 126 amp-hours over a 10-hour break. That fits inside a 200 amp-hour usable bank with room to spare. Add an electric blanket plus a mini fridge on AC and the overnight draw climbs to about 37 amps, which is 371 amp-hours over 10 hours, far beyond the bank. The calculator checks the parked break from your own overnight loads, so a flat battery in the morning does not come as a surprise. If the break fails, the honest fixes are a bigger bank, a lithium upgrade, one less overnight load, or running the engine partway through the break.
Running the engine changes the picture completely. A Class 8 alternator delivers 160 to 220 amps, with 80 to 190 amps available at idle depending on the model. That covers a 2,000W inverter load outright, so the batteries stay full while the engine runs. The cost is fuel plus engine wear, which is why many drivers compare idling against a power station or an auxiliary power unit. Our Truck Idle Cost Calculator works out the annual cost of idling, so you can weigh it against the battery route. And if the batteries do go flat, the Jump Starter Size Checker tells you whether a consumer jump pack can start a Class 8 engine, plus what size you actually need.
What size inverter do I need for a CPAP machine?
A CPAP machine alone needs a small inverter: 300W covers it with room to spare. A CPAP without the heated humidifier draws about 40W. With the humidifier running it draws about 90W. Add 25 percent headroom and the requirement is 50W to 113W, which rounds up to the smallest standard size, 300W. The inverter size is not the hard part of CPAP power. The waveform plus the overnight battery draw are.
Waveform comes first. A CPAP machine is a medical device with a sensitive power supply plus pressure sensors. Modified sine wave power can trip the supply, drift the pressure, or shut the humidifier down mid-sleep. Every major guide lists CPAP machines as pure sine wave required, with no exceptions for budget. Buy a pure sine wave inverter for any cab that runs a CPAP, even if the wattage is tiny.
Overnight draw comes second. A 90W CPAP with humidifier pulls about 8.8 amps through the inverter, which is 88 amp-hours over a 10-hour break. A 40W CPAP without humidifier pulls about 3.9 amps, which is 39 amp-hours over the same break. Both fit inside a standard 200 amp-hour usable bank on their own. The trouble starts when the CPAP shares the night with a fridge, a blanket, plus a mini fridge, which is why the calculator totals the overnight loads separately from the daytime peak.
One cheaper option skips the inverter entirely. Most CPAP makers sell a 12V DC adapter that plugs straight into the truck power socket. Running direct DC saves the 15 percent the inverter loses in conversion, which stretches the same battery bank further through the night. The tradeoff is the humidifier: some DC adapters run the humidifier at reduced power. Some do not run it at all. Check the adapter specs for your own machine before you count on it.
Can I run a fridge, microwave, plus CPAP on one inverter?
Yes, on a 2,000W pure sine wave inverter, as long as the fridge runs on 12V direct instead of through the inverter. That is the standard solo cab setup. It is the default the calculator loads with: a 700W microwave at 1,080W input, a CPAP with humidifier at 90W, a laptop at 90W, plus a 12V compressor fridge at 45W direct. The AC total is 1,260W. Add 25 percent headroom and the next standard size is 2,000W continuous, with a 4,000W surge rating that covers the 1,692W starting surge.
The overnight side of the same setup is what makes it work. While you sleep, only the CPAP plus the fridge draw power: 90W through the inverter plus 45W direct, which is 12.6 amps together, or 126 amp-hours over a 10-hour break. A standard bank of four Group 31 batteries offers 200 usable amp-hours, so the break ends with about 74 amp-hours still in reserve. The truck starts in the morning. The microwave only runs for minutes at a time, so its heavy draw never touches the overnight budget.
Two choices keep this setup honest. First, run the fridge on 12V direct. A compressor fridge draws about 45W running and about 1 amp-hour per hour on average. It skips the 15 percent inverter loss entirely. A dorm mini fridge on AC power draws more, surges to 450W at compressor start, plus pays the conversion loss on every watt. Our Truck Fridge Power Calculator works out the runtime for your own fridge, battery bank, plus parked hours, so you can see whether the fridge alone survives the break. Second, cook with 12V loads where they fit. A lunch box warmer at 100W plus a slow cooker at 60W run straight off the battery, cost nothing in inverter capacity, plus turn a rest break into a hot meal. Cooking in the cab instead of eating at the truck stop is also one of the biggest savings a driver can make: our Cook vs Eat Out Calculator puts a number on it.
For drivers who want to skip the truck batteries entirely, a portable power station is the other route: a battery plus inverter in one box, charged from the truck while driving or from solar while parked. A station sized for a fridge overnight needs roughly 400 to 700 watt-hours per night for the fridge alone, plus whatever the CPAP adds. A dedicated power station runtime calculator is planned for Trucking Mind and will cover that sizing in detail. Until it ships, the inverter math on this page still applies: watts divided by 12 volts divided by 0.85 efficiency gives the amps. Amps times hours gives the amp-hours the station must hold.
How much does a truck inverter cost?
Street prices for reputable pure sine wave units, as reported in September 2026, run about 180 to 320 dollars for 1500W, 220 to 450 dollars for 2000W, plus 350 to 750 dollars for 3000W. Those are unit prices for the inverter alone. The full install costs more: heavy copper cable, a fuse plus holder, lugs, plus mounting hardware bring the all-in figure to roughly 450 to 950 dollars for a 2000W install plus 650 to 1,400 dollars for a 3000W install. A professional install adds labor on top. Prices move with the market, so treat these bands as planning figures from September 2026, not as quotes.
Three spending rules keep the budget honest. First, buy pure sine wave unless every load is resistive. The premium over modified sine is small. It protects the CPAP plus the microwave, which are the two most expensive things the inverter feeds. Second, do not save money on cable. A 2/0 AWG copper run plus a proper fuse cost real money, but thin cable is a fire risk, not a saving. Third, size once. An inverter bought too small gets replaced within a year. The second purchase costs more than the difference between the right size plus the cheap one.
The inverter is one line in a bigger setup budget. A new owner-operator kitting out a cab needs a fridge, an inverter, a dash cam, a jump starter, straps, chains, plus a headset. The total runs into four figures fast. Our New Trucker Gear Cost Estimator totals the starter kit across budget, mid-range, plus premium tiers. For the monthly view, the Road-Living Budget Planner covers life on the road, while the Cost Per Mile Calculator shows what the truck itself costs to run.
What are the most common inverter mistakes?
The first mistake is sizing on cooking watts. A driver buys a 1000W inverter for a 1000W microwave, then wonders why it shuts down on overload. The microwave draws about 1,540W of input power, so the 1000W unit never had a chance. Size on input watts, add 25 percent headroom, then round up. The calculator does exactly that, which is why its answers run bigger than the box number.
The second mistake is thin cable. A 2,000W inverter on 4 AWG cable is a common sight in cabs. It is undersized by two full gauges on a short run. The cable heats up, the voltage at the inverter sags, the inverter alarms on low voltage, plus the driver blames the inverter. The fix is 2/0 AWG copper plus a 250A fuse at the battery. If the supplied cable looks thin next to the table in this guide, replace it before the first trip.
The third mistake is skipping the fuse, or fusing at the inverter end. The fuse protects the cable, not the inverter, so it sits at the battery, within a short distance of the positive terminal. A short in an unfused cable run can dump thousands of amps from a four-battery bank into the fault. That is a fire, not a blown fuse. Every inverter install needs a fuse at the battery, sized at 125 percent of maximum draw.
The fourth mistake is modified sine wave for a CPAP or a microwave. The unit costs less, the box claims the same watts, plus the driver finds out at 2 a.m. that the CPAP alarms or the microwave barely warms the food. Pure sine wave is the default recommendation for any cab with medical or motor loads. The calculator flags it whenever one appears on the list.
The fifth mistake is draining the starter batteries overnight. A space heater at 1,500W pulls about 147 amps, which empties a 200 amp-hour usable bank in about 80 minutes. A driver who runs a heater all night wakes up to a truck that will not start, plus a jump start bill. Heaters plus kettles are engine-on loads. The overnight loads are the CPAP, the fridge, plus the phone charger. The calculator checks that set on its own.
Frequently asked questions
What size inverter do I need for my truck?
Most solo drivers need a 2,000W pure sine wave inverter. That covers a 700W microwave at 1,080W input, a CPAP machine at 90W, plus a laptop at 90W running together, with 25 percent headroom. Drivers who only charge devices plus run a CPAP can use a 300W to 500W unit. Teams running two microwaves plus cooking need 3,000W to 5,000W. Add up the running watts of everything you use at the same time, add 25 percent headroom, then round up to the next standard size.
Can a 2000W inverter run a microwave?
Yes. A 1000W cooking microwave draws about 1,540W of input power. A 700W cooking microwave draws about 1,080W. A 2,000W continuous inverter covers either one with headroom. Its 4,000W surge rating covers the starting surge. The microwave must be a pure sine wave load: on modified sine it cooks slowly plus risks magnetron damage. Run the microwave with the engine on when you can, because it pulls 106 to 151 amps from the batteries while it runs.
Will an inverter drain my truck battery?
Yes, fast at high loads. A 1,000W load pulls about 98 amps, so a standard bank of four Group 31 batteries with 200 usable amp-hours lasts about 2 hours at that rate. A 2,000W load pulls about 196 amps and lasts about 1 hour. Overnight loads are much smaller: a CPAP plus a 12V fridge draw about 12.6 amps together, which is 126 amp-hours over a 10-hour break and fits inside the usable capacity. Run big loads with the engine on so the alternator covers the draw.
Do I need a pure sine wave inverter for a CPAP machine?
Yes. A CPAP machine is a medical device with a sensitive power supply plus pressure sensors. Modified sine wave power can trip the supply, drift the pressure, or shut the humidifier down mid-sleep. Every major guide lists CPAP machines as pure sine wave required. A 300W pure sine wave inverter covers a CPAP on its own, but most drivers buy 2,000W so the same unit also runs the microwave.
What size cable do I need for a 2000W inverter?
Use 2/0 AWG pure copper cable on a short run under 5 feet, with a 250A fuse at the battery. A 2,000W inverter pulls about 196 amps at full load, which needs 2/0 AWG at a 3 percent maximum voltage drop. A 5 to 10 foot run goes one size up to 3/0 AWG. A 10 to 15 foot run goes two sizes up to 4/0 AWG. Check the cable supplied in the box against this table: supplied cable is often too thin for a 2,000W unit.
Can I run a 12V fridge without an inverter?
Yes. That is the efficient way to run it. A 12V compressor fridge plugs straight into the truck 12V system and draws about 45W running, about 1 amp-hour per hour on average. Skipping the inverter saves the 15 percent conversion loss. A dorm mini fridge on AC power is the opposite: it needs the inverter, draws more, surges to 450W at compressor start, plus pays the conversion loss on every watt. Buy a 12V compressor fridge for the cab when you can.
Related tools
- Truck Fridge Power Calculator: work out how long your battery bank runs a 12V fridge over a parked break.
- Truck Idle Cost Calculator: work out what idling costs per year, plus the payback on an inverter or power station.
- Jump Starter Size Checker: find the jump starter rating your diesel engine needs, plus whether a consumer pack can start a Class 8 truck.
- New Trucker Gear Cost Estimator: total the starter kit for a new cab, inverter included, across budget, mid-range, plus premium tiers.
- Dash Cam Storage Calculator: size the SD card for your dash cam by resolution, channels, plus driving hours.
- Semi Truck Tire Pressure Calculator: find the right PSI for your tire size plus load per tire.
- Truck GPS Cost Comparison Calculator: compare a Garmin dezl against phone apps over one, three, plus five years.
- LED Light Bar Legal Checker: check whether auxiliary LED bars are street legal in your state.
- Sleeper Mattress Size Finder: find the mattress size that fits your truck sleeper berth.
- Cook vs Eat Out Calculator: put a number on cooking in the cab instead of eating at truck stops.
- Road-Living Budget Planner: plan the monthly cost of life on the road.
- Cost Per Mile Calculator: work out what your truck costs to run per mile.
- Pre-Trip Inspection Checklist: check battery cables, terminals, plus connections before you roll.
Sources
- Best Truck Inverters for Sleepers 2026 (otrucking, published Sep 14, 2026, read Nov 19, 2026)
- Power Inverter Size: How Big Do You Need? (bestpowerinverter, read Nov 19, 2026)
- Can a Power Station Run a Microwave? (greencommuteguide, updated Aug 12, 2026, read Nov 19, 2026)
- What Size Cable for Lithium Battery? (batteryskills, read Nov 19, 2026)
- What Is Depth of Discharge for Batteries? (EcoFlow, read Nov 19, 2026)
- How Many Batteries Are in a Semi Truck? (engineerfix, read Nov 19, 2026)
- Understanding Batteries: lithium ion vs lead acid (Spirit Energy, read Nov 19, 2026)
- 7 Pure Sine Wave vs Modified Sine Wave Inverter Facts (Victron Guy blog, updated Nov 2, 2026, read Nov 19, 2026)