Skip to main content

Trucking Mind

Plan from

Your weekly limit

Standard covers most property-carrying drivers. The 24-hour restarts apply only to the operations named in 49 CFR 395.1(d)(1), (l) and (m).

Times use your device clock. The restart counts 34 real hours, so a daylight saving change moves the completion clock time by one hour.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not professional advice โ€” verify figures from official sources before acting on them. Rates change often, so confirm the current rate with the official source before you rely on a figure.

Quick answer: A 34-hour restart is 34 or more consecutive hours off duty. When it ends, your 60-hour or 70-hour weekly limit resets to zero and a new 7-day or 8-day period begins. Enter the time you go off duty and this planner shows the exact minute your restart ends, how long is left, and confirms your full hours return. The restart is optional, and no 1 a.m. to 5 a.m. rule applies to it.

Last reviewed: ยท Focus keyword: 34 hour restart

What is a 34-hour restart?

A 34-hour restart is the reset button for the weekly hours-of-service limit. Property-carrying drivers may not drive after 60 hours on duty in 7 consecutive days, or after 70 hours on duty in 8 consecutive days, depending on whether their carrier operates every day of the week. Those limits sit in 49 CFR 395.3(b). When a driver takes 34 or more consecutive hours off duty, the 7-day or 8-day period ends and the count starts again from zero.

The rule itself is short. Section 395.3(c) says any period of 7 consecutive days may end with the beginning of an off-duty period of 34 or more consecutive hours, and the same for any period of 8 consecutive days. The clock starts the moment you go off duty, and it ends exactly 34 hours later. A driver who goes off duty at 6 p.m. on Friday may drive again at 4 a.m. on Sunday. To see where your hours stand right now, run the HOS Calculator before you plan the restart.

The restart covers the weekly limit only. It does not change the 11-hour driving limit, the 14-hour window, or the 30-minute break rule. Because 34 hours off duty is far longer than the 10 consecutive hours off duty that starts a fresh shift, a driver who finishes a restart also starts a fresh 14-hour window and a fresh 11-hour driving limit. The weekly reset is the point of the restart; the daily reset comes free with it.

How do you use the 34-Hour Restart Planner?

The planner works two ways. Plan forward from the time you go off duty, or plan backward from the time you need to roll again.

  1. Pick your cycle: 60 hours in 7 days, or 70 hours in 8 days.
  2. Pick your operation: standard, oilfield, ground water well drilling, or construction materials.
  3. If you picked a 24-hour operation, tick every eligibility box that applies to you.
  4. Enter the date and time your restart starts, or pick the time you need to roll again.
  5. Press Plan my restart to see your completion time and countdown.
  6. Stay off duty until the completion time. Any on-duty time in between restarts the count.

The countdown ticks down while the page is open, so you can check the remaining time at a glance. Your entries stay in this browser: nothing is sent to our servers, and there is no account to create. Use the copy button to save the plan as plain text.

What does a 34-hour restart reset?

A completed restart resets the weekly limit to zero. A driver on the 70-hour, 8-day cycle comes back with all 70 hours available. A driver on the 60-hour, 7-day cycle comes back with all 60 hours. The rolling window closes and a new 7-day or 8-day period opens at the start of the restart.

It also resets the daily clocks, because 34 hours off duty clears the 10 consecutive hours off duty that 395.3(a)(1) requires before a new shift. The driver starts a fresh 14-hour window and a fresh 11-hour driving limit on the first day back. Nothing else resets: the 30-minute break rule still applies after 8 hours of driving, and the restart does not change the 60-hour or 70-hour limit itself.

The restart does not erase the past week from your log. Your record of duty status still shows every hour you worked, and an inspector can still see them. What changes is the running total the rule measures you against. After a restart, the total is zero.

What breaks a 34-hour restart?

Any on-duty or driving time breaks the restart. The 34 hours must be consecutive and off duty from start to finish. If you go on duty for one hour to move the truck, fuel up, or do paperwork, the restart is broken and the 34-hour count starts over from the next time you go off duty.

Sleeper berth time counts as off-duty time for the restart, so part or all of the 34 hours can be spent in the berth. Personal conveyance, when your carrier allows it, is also off-duty time, so a short personal move does not break the restart. What matters is the duty status on your log, not where you spend the time. If you split your rest with the sleeper berth provision, the Sleeper Berth Split Calculator works out the split for you.

The common trap is small on-duty tasks that feel like nothing: a 15-minute yard move logged as on-duty not driving, a phone call that turns into dispatch work, or an inspection logged on duty. Each one breaks the restart. If you are not sure whether a task counts as on duty, check the on-duty time definition in 49 CFR 395.2 before you do it. Your ELD records the restart automatically; if you are not sure whether you need an ELD at all, the ELD Exemption Checker runs the decision tree.

Do you still need two 1 a.m. to 5 a.m. periods?

No. A 2013 rule added two conditions to the restart: it had to include two periods from 1 a.m. to 5 a.m., and a driver could use it only once every 168 hours. Congress suspended both conditions in December 2014 while the Department of Transportation studied whether they improved safety. The study, reported to Congress in March 2017, found no statistically significant benefit.

FMCSA then removed the suspended conditions from the rule in a final rule published and effective September 12, 2019 (84 FR 48081). The current text of 395.3(c) has no time-of-day requirement and no limit on how often you use the restart. A restart can start at any hour, on any day, as often as you need one.

Old guides and forum posts still repeat the 1 a.m. to 5 a.m. rule, and it still confuses drivers at roadside checks and in safety meetings. If someone tells you a restart does not count because it missed the overnight windows, they are working from a rule that stopped applying more than a decade ago.

Is the 34-hour restart required or optional?

The restart is optional. Nothing in Part 395 requires a driver to take one. A driver who reaches the 60-hour or 70-hour limit can simply wait for older hours to roll off the 7-day or 8-day window. Each midnight, the hours worked 7 or 8 days earlier drop off the total, and those hours become available again. That is the recap, and many drivers run on it for weeks without ever taking a restart.

The restart is a shortcut, not a requirement. It trades 34 hours off for a full week of hours at once. The recap trades nothing: you keep driving on the hours that roll back each day, but you never get a full week back in one step. Which one wins depends on how many hours you work each day and how the freight is timed.

One exception is worth knowing. The 16-hour short-haul exception in 395.1(o) can be used only once in 6 consecutive days, unless the driver has begun a new 7-day or 8-day period with a 34-hour restart. A restart resets that exception too. Check whether the exception covers you with the Short-Haul Exemption Checker.

34-hour restart vs recap: which is better?

A restart wins when you work long days. A driver who runs 10 hours a day on a 70-hour cycle hits the limit on day 7 and gains back only 10 hours a day after that. A 34-hour restart gives all 70 hours back at once, which is worth more than a week of 10-hour recaps.

The recap wins when you work short days or the freight is light. A driver who runs 7 hours a day never hits the 70-hour limit at all, so a restart buys nothing. A driver who runs 8 or 9 hours a day may gain more by keeping the wheels turning on recap hours than by parking for 34 hours.

Run the numbers before you decide. The 60/70-Hour Recap Calculator shows your hours available today, the hours that roll back at midnight for the next 3 days, and the restart-versus-recap comparison over the next 7 days. Use it with this planner: the recap calculator tells you what waiting earns, and this planner tells you what a restart earns.

Dispatch timing matters too. A restart that ends at 4 a.m. on a Sunday is worthless if the load picks up Monday morning and the recap would have covered it. A restart that ends Friday night before a busy weekend can be worth more than the hours it costs. Plan around the freight, not just the clock.

Who can use a 24-hour restart instead?

Three kinds of operation can reset the weekly limit with 24 consecutive hours off duty instead of 34. The oilfield 24-hour restart sits in 395.1(d)(1), the ground water well drilling restart in 395.1(l), and the construction materials restart in 395.1(m). Each one has its own eligibility test, and the planner checks it before it applies the shorter restart.

Oilfield drivers must drive a commercial motor vehicle used exclusively in the transportation of oilfield equipment, including the stringing and picking up of pipe used in pipelines, and servicing the field operations of the natural gas and oil industry. Note the word exclusively: a driver who hauls oilfield equipment one week and general freight the next does not qualify. The oilfield restart also ends an 8-day period only, so it does not apply on a 60-hour, 7-day cycle.

Ground water well drilling drivers must be used primarily in the transportation and operations of a ground water well drilling rig. Construction drivers must be used primarily in the transportation of construction materials and equipment, running to or from an active construction site within a 75 air-mile radius of their normal work reporting location. The construction restart does not cover placarded hazardous materials. A state may set a different radius between 50 and 75 air miles for trips that stay inside the state.

OperationRuleRestart lengthCycle
Standard395.3(c)34 hours7-day or 8-day
Oilfield395.1(d)(1)24 hours8-day only
Ground water well drilling395.1(l)24 hours7-day or 8-day
Construction materials and equipment395.1(m)24 hours7-day or 8-day

If you do not meet every condition, the planner falls back to the standard 34-hour restart and tells you which condition failed. Do not use the 24-hour restart on a guess: a restart that does not qualify leaves you over the weekly limit, and the violation shows up on your log.

Worked examples

Friday night restart. A driver on the 70-hour cycle finishes Friday at 6 p.m. with 68 hours on the clock. She goes off duty at 6 p.m. Friday. The restart ends Sunday at 4 a.m., 34 hours later. She starts Sunday with all 70 hours available and a fresh 14-hour window.

Midnight crossing. A driver goes off duty at 11:45 p.m. on a Tuesday. The restart ends at 9:45 a.m. on Thursday. The date changes twice during the restart, but the count is 34 elapsed hours, not two calendar days. The planner counts real hours, so daylight saving time changes are handled the same way: the restart is 34 hours of real time, and the clock time it ends at shifts by an hour across a spring or fall time change.

Planning backward. A driver needs to roll again at 6 a.m. on Monday for a 7 a.m. pickup. Working backward 34 hours, the restart must start by 8 p.m. on Saturday. Starting later than that means the restart is still running at 6 a.m. Monday, and driving before it ends breaks it. Once you know when you roll again, the Trip Time Estimator works out your arrival time.

Oilfield 24-hour restart. An oilfield driver on the 70-hour cycle goes off duty at 7 p.m. on Wednesday and meets the oilfield test. The restart ends at 7 p.m. on Thursday, 24 hours later, and all 70 hours return.

What are the most common 34-hour restart mistakes?

  1. Counting calendar days instead of hours. A restart is 34 elapsed hours, not two days off. Going off duty at 8 p.m. and coming back at 8 p.m. two days later is 48 hours, which is fine, but going off duty at 8 p.m. and coming back at 6 a.m. two days later is only 34 hours if the dates line up exactly. Count the hours, not the days.
  2. Going on duty for a quick task. A 10-minute inspection, a fuel stop logged on duty, or a phone call that becomes dispatch work all break the restart. The count starts over from the next off-duty minute.
  3. Trusting the old 1 a.m. to 5 a.m. rule. Some drivers still plan restarts around two overnight windows that have not applied since 2014. That wastes hours and can push a restart past the time the freight needs.
  4. Assuming the restart covers passenger-carrying driving. The restart is in 395.3(c), which covers property-carrying drivers only. Passenger-carrying drivers work under 395.5, which has no restart provision. Their hours return only as older days roll off the window.
  5. Forgetting the restart is optional. Some drivers take a restart every week out of habit, even when the recap would have kept them rolling. Check the recap before you park for 34 hours.

Frequently asked questions

Does a 34-hour restart reset the 14-hour clock?

Yes. A 34-hour restart is 34 consecutive hours off duty, which is far longer than the 10 consecutive hours off duty that 395.3(a)(1) requires before a new shift. When you come back on duty after a restart, you start a fresh 14-hour window and a fresh 11-hour driving limit, as well as a fresh 60-hour or 70-hour weekly limit.

Can I split a 34-hour restart into two breaks?

No. The 34 hours must be consecutive. Any on-duty or driving time in the middle breaks the restart, and the 34-hour count starts over from the next time you go off duty. Sleeper berth time counts, and you may mix off-duty and sleeper berth time, but the period itself cannot be split.

Does sleeper berth time count toward a 34-hour restart?

Yes. Time in the sleeper berth counts as off-duty time for the restart, so part or all of the 34 hours can be spent in the berth. What matters is that the full 34 hours are consecutive and free of on-duty or driving time.

How often can I take a 34-hour restart?

As often as you want. The old once-per-week limit was suspended by Congress in December 2014 and formally removed from the rule in September 2019. There is no limit on how many restarts you take, and no minimum gap between them.

Do I still need two 1 a.m. to 5 a.m. periods in a restart?

No. That requirement was added in 2013, suspended by Congress in December 2014, and removed from 49 CFR 395.3(c) by a final rule effective September 12, 2019 (84 FR 48081). A restart can start at any time of day and does not need to cover any particular overnight hours.

Can a passenger-carrying driver use a 34-hour restart?

No. The restart is in 395.3(c), which covers property-carrying drivers only. Passenger-carrying drivers work under 395.5, which sets a 60-hour/7-day or 70-hour/8-day limit with no restart provision, so their hours return only as older days roll off the 7-day or 8-day window.

Related tools

Sources

  1. 49 CFR 395.3, Maximum driving time for property-carrying vehicles. law.cornell.edu/cfr/text/49/395.3 Accessed November 19, 2026.
  2. 49 CFR 395.1, Scope of rules in this part. law.cornell.edu/cfr/text/49/395.1 Accessed November 19, 2026.
  3. 49 CFR 395.2, Definitions. law.cornell.edu/cfr/text/49/395.2 Accessed November 19, 2026.
  4. 49 CFR 395.5, Maximum driving time for passenger-carrying vehicles. law.cornell.edu/cfr/text/49/395.5 Accessed November 19, 2026.
  5. FMCSA, Summary of Hours of Service Regulations. fmcsa.dot.gov/regulations/hours-service/summary-hours-service-regulations Accessed November 19, 2026.
  6. FMCSA final rule removing the suspended restart provisions, 84 FR 48081, September 12, 2019.
Follow on WhatsApp Ask by Voice