Skip to main content

Trucking Mind

Federal equipment rules only. This checker applies 49 CFR 393.17, 393.71 plus 396.15 to the combination you describe. State size and weight limits, permits, escorts plus curfews are separate and are not covered here. Confirm them before the trip.

Describe the combination, the tow-bar, the saddle-mount, the lamps plus the Part 396 duties. Every answer updates the result as you change each field. Sections that do not apply to your combination show as Not applicable.

About the combination

The saddle-mount tables use the weight of the heaviest towed vehicle. For a single saddle-mount, the tables use the total weight of all the vehicles being towed, so enter that total here when you check a single saddle-mount.

Tow-bar

Skip this section when the combination has no tow-bar: the checks show as Not applicable. A ball-and-socket coupling counts toward the 1 device limit in the combination section above.

Tracking is the distance the towed vehicle deviates to one side of the path of the towing vehicle moving in a straight line, measured from the center of the towing vehicle. The limit is 3 in.

Saddle-mount

Skip this section when the combination has no saddle-mount. Check the front mount first: it carries the highest loads in every table. Diameters are entered in sixteenths of an inch: 8 is 1/2 in, 9 is 9/16 in, 10 is 5/8 in, 11 is 11/16 in, 12 is 3/4 in, 16 is 1 in, 24 is 1 1/2 in.

Lamps

Part 396 duties

Combination not legal: 1 problem to fix.

12 checks passed, 1 check failed, 2 checks not applicable.

Failed check: tow-bar marking. Fix every failed check before the combination moves. A roadside inspector cites each failed item separately under Part 393 or Part 396.

The checks

CheckResultDetail
Combination limits, section 393.71(a)Pass1 saddle-mount plus 1 tow-bar in a 3 vehicle combination. Within the limits of 3 saddle-mounts plus 1 tow-bar or ball-and-socket device.
Full-mounted vehicles, section 393.71(b) and (c)Not applicableNo vehicle is full-mounted on another vehicle in this combination.
Tow-bar strength, section 393.71(h)(1)PassLongitudinal strength 20,000 lb against 15,600 lb required. The beam test does not apply because the tow-bar is not subjected to a bending movement in normal operation.
Bumper tow-bar, section 393.71(d)PassThe tow-bar does not depend upon the bumpers to transmit forces between the vehicles.
Tow-bar marking, section 393.71(h)(9)FailEvery tow-bar acquired and used in driveaway-towaway operations must be plainly marked with the manufacturer certification or words of equivalent meaning.
Safety devices, section 393.71(h)(10)Pass2 safety chains or cables, crossed and attached near the bumper attachment points, with combined tensile strength 20,000 lb against 15,600 lb required.
Tracking, section 393.71(h)(7) and (m)(3)PassThe towed vehicle deviates 2 in, within the 3 in limit to either side of the path of the towing vehicle.
Saddle-mount U-bolts, section 393.71(j)(2) and (k)(1)PassUpper-half U-bolt diameter 0.625 in (5/8 in) against 0.5625 in (9/16 in) required. Lower-half U-bolt area 1.00 sq in against 1.00 sq in required.
Saddle-mount kingpin, section 393.71(l)PassKingpin diameter 1 in (1 in) against 1 in (1 in) required for a single saddle-mount in mild steel.
Lower-half strength and support height, section 393.71(k)PassLower-half test load 10,000 lb against 10,000 lb required. Support height 20 in against the 24 in limit.
Hardwood blocks, section 393.71(k)(4)Not applicableNo hardwood blocking is used to build up the height of the front end of the towed vehicle.
Saddle-mount marking, section 393.71(m)(8)PassThe upper half and the lower half are each marked with the manufacturer certification.
Front wheels and forward towing, section 393.71(e) and (f)PassFront wheels restrained where required, plus the vehicle towed front-end first or with the steering locked straight.
Lamp sets, section 393.17PassThe towing vehicle, the rearmost towed vehicle plus each intermediate towed vehicle carry the lamp sets section 393.17 requires.
Part 396 duties, section 396.15PassPre-trip inspection plus post-trip disassembly and inspection are done. The towed vehicles are part of the shipment being delivered, so section 396.3 records, the section 396.11 report plus the section 396.17 periodic inspection do not apply to them.

The figures

FigureValueNote
Vehicles in the combination31 towing vehicle plus 2 towed vehicles.
Required tow-bar longitudinal strength15,600 lb12,000 lb x 1.3 = 15,600 lb. The formula governs for a new tow-bar at 5,000 lb and above.
Required safety-device strength15,600 lbThe combined tensile strength of the safety chains or cables must at least equal the required tow-bar longitudinal strength.
Required upper U-bolt diameter0.5625 in (9/16 in)Position: single saddle-mount. Weight band: 12,000 lb, 5,000 lb and over.
Required kingpin diameter1 in (1 in)Position: single saddle-mount, mild steel. High-tensile steel means a minimum ultimate strength of 65,000 lb per sq in.
Required lower-half U-bolt area1.00 sq inTotal cross-sectional area of the lower-half U-bolts for a single saddle-mount.
Required lower-half test load10,000 lbThe lower half must support this load in test, mounted as normally operated, with the load applied through the upper half.
Support height limit24 inHighest point of support above the top of the frame of the towing vehicle. Entered: 20 in.
Part 396 exemptionsApplySection 396.3 records, the section 396.11 vehicle inspection report plus the section 396.17 periodic inspection do not apply to the vehicles that are part of the shipment being delivered.

What to do

  • Use a tow-bar plainly marked with the manufacturer certification or words of equivalent meaning.

Lamp sets, exemptions and duties

  • Towing vehicle: 2 headlamps, 2 turn signals plus 2 clearance lamps on the front; 1 side-marker lamp on each side near the front; 2 tail lamps plus 2 stop lamps on the rear.
  • Rearmost towed vehicle: 1 side-marker lamp on each side near the rear; 2 tail lamps, 2 stop lamps, 2 turn signals, 2 clearance lamps plus 2 reflectors on the rear.
  • Each intermediate towed vehicle: 1 side-marker lamp on each side near the rear.
  • Exemption: the towed vehicles are part of the shipment being delivered, so section 396.3 records, the section 396.11 vehicle inspection report plus the section 396.17 periodic inspection do not apply to them. The towing vehicle keeps its full Part 396 duties.
  • Before the trip, section 396.15(b) requires a careful inspection and test: connections properly secured, parts working without cramping or binding, plus the towed vehicle following the path of the towing vehicle without whipping or swerving.
  • After the trip, section 396.15(c) requires the tow-bars and saddle-mounts to be disassembled and inspected for worn, bent, cracked, broken or missing parts before reuse, with defective parts repaired or replaced.

Notes

  • Trailers transported in a driveaway-towaway operation are excepted from the retroreflective sheeting and reflex reflector rules in section 393.13(a).
  • The saddle-mount tables overlap at exactly 5,000 lb: both the up to 5,000 lb row plus the 5,000 lb and over row read literally. This tool applies the stricter row at 5,000 lb and above.
  • State size and weight limits, permits, escorts plus curfews are separate from the federal equipment rules in this check.
  • A semi-trailer with an upper coupler assembly may be towed on a fifth-wheel meeting section 393.70 instead of a tow-bar or saddle-mount, under section 393.71(g).
  • This tool checks the federal rules only. A roadside inspector applies the same sections plus the CVSA out-of-service criteria.

This tool applies 49 CFR 393.17, 393.71 plus 396.15 to your inputs. Confirm the result against the regulation plus your equipment records before moving the combination.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is a planning estimate based on the published federal rules, not legal advice — confirm the combination with FMCSA guidance or your legal counsel before moving a load.

Quick answer: A driveaway-towaway operation moves an empty or unladen vehicle with one or more sets of wheels on the roadway, usually from a factory or dealer to a buyer. Federal law caps the combination at 3 saddle-mounts plus 1 tow-bar or ball-and-socket device. A tow-bar for a vehicle of 5,000 lb or more needs longitudinal strength of 1.3 times the towed weight, plus safety chains with the same combined strength. Saddle-mounts follow size tables for U-bolts, kingpins plus lower halves. Each position in the combination carries its own lamp set under section 393.17. Vehicles that are part of the shipment being delivered skip the section 396.3 records, the section 396.11 report plus the section 396.17 periodic inspection. This checker runs all 15 checks at once.

Last reviewed: · Focus keyword: driveaway towaway regulations

What is a driveaway-towaway operation?

A driveaway-towaway operation moves an empty or unladen motor vehicle with one or more sets of wheels on the surface of the roadway. That is the definition in section 390.5T. It covers six kinds of move: between vehicle manufacturer facilities; between a vehicle manufacturer and a dealership or purchaser; between a dealership, or other entity selling or leasing the vehicle, plus a purchaser or lessee; to a motor carrier terminal or repair facility for the repair of disabling damage following a crash; to a motor carrier terminal or repair facility for repairs associated with the failure of a vehicle component or system; or by means of a saddle-mount or tow-bar. The common thread is that the vehicle being moved rolls on its own wheels instead of riding on a trailer.

The most common driveaway-towaway move is new-vehicle delivery. A driveaway carrier picks up a new truck, bus, or recreational vehicle at the factory, couples it behind a towing vehicle with a tow-bar or a saddle-mount, plus delivers it to a dealer or a buyer. The same method moves a wrecked truck to a repair shop after a crash, or a truck with a failed engine to a terminal. In every case the towed vehicle is empty or unladen: it carries no freight, plus in most cases it carries no driver either. The towing vehicle supplies the power, the steering input through the coupling, plus the braking for the combination, except where the rules require brakes on the towed vehicle itself.

Two coupling methods dominate the work. A tow-bar connects the towing vehicle to the towed vehicle at frame or bumper level, with the towed vehicle rolling on all of its own wheels. A saddle-mount lifts the front end of the towed vehicle onto a mount fixed to the frame of the towing vehicle, so the towed vehicle rolls on its rear wheels only. Saddle-mounts stack: the first saddle-mounted vehicle can carry a second saddle-mounted vehicle on its own frame, plus the second can carry a third. That stacking is what makes the triple saddle-mount combination possible. It is why the saddle-mount tables grow stricter toward the front of the combination, where the loads are highest.

Driveaway-towaway operations sit under their own corner of the Federal Motor Carrier Safety Regulations. Section 393.71 sets the coupling and towing rules, section 393.17 sets the lamp sets for the combination, plus section 396.15 sets the inspection duties and the exemptions for vehicles that are part of the shipment being delivered. The general equipment rules of Part 393 still apply to the towing vehicle in the ordinary way. The driveaway-towaway sections add rules for the combination itself, plus they relax a few Part 396 duties for the vehicles being delivered as cargo. A carrier that runs driveaway work needs both sets in mind: the towing vehicle must be a legal truck on its own, plus the combination must meet the driveaway-towaway rules as a unit.

The checker above runs the driveaway-towaway rules as 15 checks. It does not check the towing vehicle against the general Part 393 equipment rules: tires, brakes, lights on the towing vehicle itself, plus the driver rules in Part 392 all sit outside it. Use the Tire Compliance Checker for the tire rules that apply to every vehicle in the combination, including the towed vehicles rolling on their own tires, plus the Lighting and Reflector Checker for the general lamp rules on the towing vehicle.

How many vehicles can a driveaway-towaway combination carry?

Section 393.71(a) sets two caps. No more than 3 saddle-mounts may be used in any combination. No more than 1 tow-bar or ball-and-socket type coupling device may be used in any combination. The caps are separate: a combination may use saddle-mounts plus a tow-bar together, up to 3 of the first plus 1 of the second. A single saddle-mount combination has 2 vehicles. A double saddle-mount combination has 3. A triple saddle-mount combination has 4. A tow-bar combination has 2. The largest combination the caps allow is 5 vehicles: 1 towing vehicle, 1 tow-bar-towed vehicle, plus 3 saddle-mounted vehicles.

The triple saddle-mount combination carries an extra brake rule. Section 393.71(a)(3) says that when motor vehicles are towed by means of triple saddle-mounts, all but the final towed vehicle must have brakes acting on all wheels in contact with the roadway. The final towed vehicle, the one at the back of the stack, is the only one excused. The rule exists because a triple stack puts three unpowered vehicles behind one towing vehicle. The towing vehicle brakes alone cannot stop that much weight safely. Each saddle-mounted vehicle except the last must contribute braking through its own wheels on the road. A carrier that runs triple saddle-mounts without working brakes on the middle vehicles is running an illegal combination, even if every coupling is sound.

The same brake logic appears in the full-mounting rules. A vehicle full-mounted on a tow-bar-towed vehicle is allowed only when the towed vehicle is equipped with brakes and means for effective application of brakes acting on all wheels, plus is towed on its own wheels. A vehicle full-mounted on a saddle-mounted vehicle is allowed only when the saddle-mounted vehicle has effective brakes acting on all wheels in contact with the roadway at all times while so loaded. The pattern is consistent: the more weight a towed vehicle carries, the more the rules insist that it brakes for itself.

Section 393.71(g) limits the means of towing. No motor vehicles or combination of motor vehicles may be towed in driveaway-towaway operations by means other than a tow-bar, a ball-and-socket type coupling device, saddle-mount connections which meet the requirements of the section, or, in the case of a semi-trailer equipped with an upper coupler assembly, a fifth-wheel meeting the requirements of section 393.70. A rope, a chain used as the primary coupling, or an improvised drawbar does not qualify. The fifth-wheel option matters for semi-trailers being delivered as part of a driveaway move: the trailer couples to the tractor fifth-wheel in the ordinary way, under the section 393.70 rules that the Coupling and Safety Chain Checker covers.

State size and weight limits sit on top of the federal combination caps. A 5 vehicle combination that passes section 393.71(a) may still exceed a state overall-length limit or a state weight limit on a given route. The federal caps decide whether the combination is legal as a driveaway-towaway operation. The state limits decide whether it may run on a particular highway. Check both before dispatch. A violation of either set draws its own citation, plus the FMCSA Fine Calculator works out the current federal penalty for a Part 393 violation.

How strong must a tow-bar be?

Section 393.71(h)(1) sets the tow-bar strength table. The required strength depends on the gross weight of the towed vehicle plus the age of the tow-bar. The table has three strength columns: longitudinal strength for all tow-bars, longitudinal strength for new tow-bars acquired and used after Sept. 30, 1948, plus strength as a beam. In practice every tow-bar in service today is a new tow-bar under the table, because the Sept. 30, 1948 cutoff is more than 75 years old. The old tow-bar column survives as a legacy rule for equipment that predates it.

Gross weight of towed vehicleLongitudinal strength, all tow-barsLongitudinal strength, new tow-barsStrength as a beam
Less than 5,000 lb3,000 lb6,500 lb3,000 lb
5,000 lb to less than 10,000 lb6,000 lbGross weight x 1.3Gross weight x 0.6
10,000 lb to less than 15,000 lb9,000 lbGross weight x 1.3Gross weight x 0.6
15,000 lb and overGross weight x 1.3Gross weight x 1.3Gross weight x 0.6

The formulas are the heart of the table. For a towed vehicle of 15,000 lb and over, every tow-bar needs longitudinal strength equal to the gross weight of the towed vehicle times 1.3, plus beam strength equal to the gross weight times 0.6. For a new tow-bar towing a vehicle of 5,000 lb and over, the same formulas apply. A new tow-bar towing a 12,000 lb truck needs 15,600 lb of longitudinal strength. A new tow-bar towing a 20,000 lb bus needs 26,000 lb of longitudinal strength plus 12,000 lb of beam strength. A new tow-bar towing a 4,000 lb car needs a flat 6,500 lb of longitudinal strength, because the formula does not apply below 5,000 lb for new tow-bars. The checker above runs this table from the weight plus the tow-bar age you enter.

One figure in the table is widely mislabeled in secondary summaries. Some summaries list the under 5,000 lb row as 3,000 lb longitudinal, 6,500 lb beam, plus 3,000 lb concentrated center load. That misreads the columns. The 6,500 lb figure is the longitudinal strength for a NEW tow-bar, not the beam strength. The beam strength for a towed vehicle under 5,000 lb is 3,000 lb, which is the same figure as the concentrated center load in the beam test. The distinction matters when a carrier buys a tow-bar: a bar rated at 3,000 lb longitudinal strength is legal only for an old tow-bar under 5,000 lb. A new tow-bar for the same car needs 6,500 lb.

The beam test applies only to tow-bars which are, in normal operation, subjected to a bending movement, such as tow-bars for house trailers. A straight tow-bar that transmits force along its longitudinal axis only does not need a beam rating. A tow-bar that bends in service needs both ratings. The test loads the bar at the center with the whole unit tested with all clamps, joints plus pins mounted as in actual operation. The checker asks whether the tow-bar bends in normal operation, plus it checks the beam rating only when the answer is yes.

Three more tow-bar rules sit in section 393.71(h). The tow-bar must be jointed so it freely permits motion in both horizontal plus vertical planes between the towed and towing vehicles, while transmitting stresses only along the longitudinal axis of the tongue. An adjustable tow-bar must fit tightly, with no slackness, plus the sag at the center under a 50 lb load must not exceed 0.25 in in any direction. The tow-bar must connect to the steering mechanism of the towed vehicle, where the towed vehicle has one, with enough angularity that the towed vehicle follows substantially in the path of the towing vehicle without cramping the tow-bar. A tow-bar that binds, sags, or fights the steering is a violation even when its strength ratings pass.

Bumper tow-bars carry their own ban. Section 393.71(d) says tow-bars of the type which depend upon the bumpers as a means of transmitting forces between the vehicles must not be used to tow a motor vehicle weighing more than 5,000 lb. A bumper tow-bar is legal for a light car. It is not legal for a 6,000 lb pickup, a box truck, or a bus. The bumper is not a frame member, plus it cannot carry the towing loads of a heavy vehicle. A carrier that tows heavy vehicles on bumper bars is risking a separation at highway speed. The checker flags any bumper tow-bar above the 5,000 lb line.

Every tow-bar must be plainly marked with the manufacturer certification, or words of equivalent meaning, under section 393.71(h)(9). The marking is the roadside proof that the bar meets the strength table: an inspector who cannot read a certification on the bar has no way to verify the rating, plus an unmarked bar draws a citation. The towing vehicle itself still needs its own USDOT number plus legal name marking under the vehicle marking rules, which the Vehicle Marking Checker covers.

What safety devices does a tow-bar combination need?

Section 393.71(h)(10) requires a safety device to prevent the towed vehicle from breaking loose if the tow-bar fails or becomes disconnected. When safety chains or cables are used as the safety device, at least 2 chains or cables are required. One chain is never enough, however strong it is. The rule wants redundancy: if one chain fails, the other still holds the towed vehicle behind the towing vehicle long enough for the driver to stop.

The strength rule ties the safety device to the tow-bar table. The tensile strength of the safety device plus the means of attachment to the vehicles must be at least equivalent to the corresponding longitudinal strength for tow-bars required in the table of paragraph (h)(1). When safety chains or cables are used, the required strength is the combined strength of the combination of chains and cables. Two chains rated at 8,000 lb each give 16,000 lb of combined strength, which passes for a tow-bar requirement of 15,600 lb. Two chains rated at 6,000 lb each give 12,000 lb, which fails the same requirement. The checker adds the combined strength you enter plus compares it with the required longitudinal strength from the table.

Installation matters as much as strength. Section 393.71(h)(10)(ii) says the chains or cables must be crossed and attached to the vehicles near the points of bumper attachment to the chassis of the vehicles. The length of chain used must be no more than necessary to permit free turning of the vehicles. The chains must be attached to the tow-bar at the point of crossing or as close to that point as is practicable. Crossed chains form a cradle under the tow-bar tongue: if the tow-bar disconnects, the tongue drops onto the crossed chains instead of dropping to the road, where it would dig in plus pole-vault the towed vehicle. Chains left long enough to drag, or run straight instead of crossed, fail the rule even when they are strong enough.

A safety device other than safety chains or cables must provide strength, security of attachment, plus directional stability equal to, or greater than, that provided by safety chains or cables installed as the rule describes. It must also be designed, constructed plus installed so that, if the tow-bar fails or becomes disconnected, the tow-bar will not drop to the ground. A cable system, a secondary coupling, or a manufactured safety device can qualify if it meets that standard. An improvised rope or a single strap cannot.

Safety chains for driveaway-towaway work are different from the safety chains on a full trailer under section 393.70. The section 393.70 rules set the chain strength at the gross weight of the towed vehicle, with their own attachment geometry plus a ban on attaching to a pintle hook. The section 393.71(h)(10) rules set the strength at the tow-bar longitudinal strength from the (h)(1) table, which is 1.3 times the towed weight for most modern tow-bars. A carrier that runs both kinds of work needs both standards in mind. The Coupling and Safety Chain Checker covers the section 393.70 side: fifth wheels, pintle hooks, plus safety chains for trailers.

What are the saddle-mount requirements?

A saddle-mount has two halves. The upper half attaches to the frame or axle of the towed vehicle. The lower half attaches to the frame of the towing vehicle. A kingpin joins the two halves and lets the towed vehicle pivot behind the towing vehicle. Section 393.71 sets size tables for each part, with the sizes growing toward the front of the combination, where the loads are highest, plus growing again for heavier towed vehicles. The tables use two weight bands: up to 5,000 lb, plus 5,000 lb and over. The checker asks which mount position you are checking, then reads the right row of each table.

The upper-half U-bolt table sits in section 393.71(j)(2). U-bolts must be made of steel rod, free of defects, shaped to avoid a radius of less than 1 in at any point, unless the fabrication keeps the reduction in cross-sectional area at points of curvature to 5 percent or less, in which case the minimum radius is 1/16 in. The diameter table is as follows.

Weight of heaviest towed vehicleFront mountMiddle or front mountRear mountSingle saddle-mount
Up to 5,000 lb0.625 in (5/8 in)0.5625 in (9/16 in)0.500 in (1/2 in)0.500 in (1/2 in)
5,000 lb and over0.6875 in (11/16 in)0.625 in (5/8 in)0.5625 in (9/16 in)0.5625 in (9/16 in)

The distance between the most widely separated U-bolts must not be less than 9 in, plus the distance between the widely separated points where the upper half supports the towed vehicle must not be less than 9 in, except that saddle-mounts with ball and socket joints must clamp the axle of the towed vehicle through a length of not less than 5 in. Cradle-type upper halves need at least one bolt of 1/2 in diameter or equivalent means against relative vertical movement, with no more than 1/2 in of relative motion allowed. Towed vehicles with a straight axle or an axle with a drop of less than 3 in need chains or cables of at least 3/16 in diameter to restrain lateral motion, unless the mount is built to prevent lateral motion by design.

The lower-half tables sit in section 393.71(k). The U-bolt table gives total cross-sectional area, not diameter: the lower half is judged on the combined area of its U-bolts. The test-load table gives the load the lower half must support in test, mounted as normally operated, with the load applied through the upper half.

Weight of heaviest towed vehicleFront mountMiddle or front mountRear mountSingle saddle-mount
U-bolt area, up to 5,000 lb1.20 sq in1.00 sq in0.80 sq in0.80 sq in
U-bolt area, 5,000 lb and over1.40 sq in1.20 sq in1.00 sq in1.00 sq in
Test load, up to 5,000 lb15,000 lb10,000 lb5,000 lb5,000 lb
Test load, 5,000 lb and over30,000 lb20,000 lb10,000 lb10,000 lb

The lower half must also control shifting plus swaying. Tripod-type designs need hold-back chains or similar devices against shifting during rapid acceleration plus deceleration. Lower halves with separable cross-members need at least two bolts on each side fastening the cross-member to the vertical members, with the bolts at least equal in cross-sectional area to the U-bolts for the same mount, plus at least 3 in between the most widely separated points of support. The bearing surface on the frame of the towing vehicle must keep the pressure at or below 200 lb per sq in under any static loading. Hardwood blocks or blocks of other suitable material between the lower half plus the frame must be at least 1/2 in thick, 3 in wide, plus a combined length of 6 in.

The support-height rule is simple plus strict. Section 393.71(k)(3)(iii) says the highest point of support of the towed vehicle by the upper half must be no more than 24 in, measured vertically, above the top of the frame of the towing vehicle, measured at the point where the lower half rests on the towing vehicle. A mount that lifts the towed vehicle too high raises its center of gravity plus makes the combination unstable in a turn or a wind gust. The checker flags any support height above 24 in.

Hardwood blocking has its own limits in section 393.71(k)(4). Hardwood blocks of good quality may build up the height of the front end of the towed vehicle, provided the total height of the blocks does not exceed 8 in plus no more than 2 separate pieces are placed on each other. Up to 4 blocks to a total height of 14 in are allowed when the total cross-sectional area of the U-bolts used to attach the lower half is at least 50 percent greater than the table figure. Blocks must be at least 4 in wide, with planed surfaces between blocks, or between a block plus the lower or upper half, installed to minimize any tendency of the towed vehicle to sway or rock. The checker runs both blocking allowances from the height, the piece count, plus the U-bolt area you enter.

The kingpin table sits in section 393.71(l)(1). Kingpins must be steel suitable for the purpose, free of defects, with a diameter not less than the table figure. High-tensile steel, defined as steel with a minimum ultimate strength of 65,000 lb per sq in, allows a smaller diameter than mild steel at the same position plus weight.

Weight of heaviest towed vehicleFront mountMiddle or front mountRear mountSingle saddle-mount
Mild steel, up to 5,000 lb1.125 in1.000 in0.875 in0.875 in
Mild steel, 5,000 lb and over1.500 in1.250 in1.000 in1.000 in
High-tensile steel, up to 5,000 lb1.000 in0.875 in0.750 in0.750 in
High-tensile steel, 5,000 lb and over1.125 in1.000 in0.875 in0.875 in

A ball and socket joint used in place of a kingpin needs a ball neck diameter at least equal to the diameter of the corresponding solid kingpin. A hollow kingpin needs metallic cross-sectional area at least equal to the cross-sectional area of the corresponding solid kingpin. The kingpin must fit snugly without binding, with smoothly machined contact surfaces plus a bearing surface not less in depth than the radius of the kingpin. New saddle-mounts need the kingpin snugly enclosed in a bushing along the length in moving contact with either half. The kingpin must restrain the upper half from moving vertically relative to the lower half.

The remaining saddle-mount rules sit in section 393.71(m). The bearing surface between the upper plus lower halves must be at least 16 sq in under any angularity between the vehicles, with a ball and socket joint limited to 800 lb per sq in of static bearing load on the projected area of the ball. The mount must provide for angularity from vertical highway curves without depending on looseness or deformation of the parts. The mount must not sit at a point to the rear of the frame of the towing vehicle. All nuts must be secured against accidental disconnection with cotter keys, lock washers, double nuts, safety nuts, or equivalent means, plus fully engaged. The mount must be designed so it can be disassembled with each part inspected for worn, bent, cracked, broken, or missing parts. Every new saddle-mount must have the upper half plus the lower half separately marked with the manufacturer certification or words of equivalent meaning.

One table detail deserves attention. The saddle-mount tables read “Up to 5,000” plus “5,000 and over”, so both rows read literally at exactly 5,000 lb. A towed vehicle of exactly 5,000 lb sits on the boundary. This checker applies the stricter row at 5,000 lb and above, which is the safe reading: the heavier row can never be wrong at the boundary, while the lighter row might be. A carrier checking a vehicle at exactly 5,000 lb should use the heavier row figures when buying or inspecting a mount.

What lamps does a driveaway-towaway combination need?

Section 393.17 sets a separate lamp set for each position in the combination: the towing vehicle, the rearmost towed vehicle, plus each intermediate towed vehicle. The sets differ because each position faces different traffic: the towing vehicle needs forward lamps plus rear lamps that the towed vehicles behind it may hide, the rearmost vehicle needs the full rear set that following traffic sees, plus the intermediate vehicles need only side-markers so their length is visible from the side.

PositionFrontEach sideRear
Towing vehicle2 headlamps, 2 turn signals, 2 clearance lamps1 side-marker lamp near the front2 tail lamps, 2 stop lamps
Rearmost towed vehicleNone required by section 393.171 side-marker lamp near the rear2 tail lamps, 2 stop lamps, 2 turn signals, 2 clearance lamps, 2 reflectors, plus 3 identification lamps when any vehicle is 80 in or more wide
Intermediate towed vehicleNone required by section 393.171 side-marker lamp near the rearNone required by section 393.17
Mobile structure trailer, daylight-only permitNone required by section 393.17None required by section 393.172 stop lamps, 2 tail lamps, 2 red reflex reflectors, 2 turn signals

The towing vehicle set in paragraph (a) is the full front set plus a rear set: at least 2 headlamps, an equal number at each side, 2 turn signals, one at each side, plus 2 clearance lamps, one at each side, on the front; at least 1 side-marker lamp on each side, located near the front; plus at least 2 tail lamps plus 2 stop lamps on the rear. The rear lamps on the towing vehicle matter because the towed vehicle behind it may hide the towing vehicle rear lamps from following traffic in some configurations, so the set is specified even though the rearmost vehicle carries its own rear lamps.

The rearmost towed vehicle set in paragraph (b) is the heaviest set in the section. It covers the towed vehicles of a tow-bar combination, the towed vehicle of a single saddle-mount combination, plus the rearmost towed vehicle of a double or triple saddle-mount combination. Where a vehicle is full-mounted on a saddle-mount vehicle, either the full-mounted vehicle or the rearmost saddle-mounted vehicle must carry the set. On each side there must be at least 1 side-marker lamp near the rear. On the rear there must be at least 2 tail lamps, 2 stop lamps, 2 turn signals, 2 clearance lamps, plus 2 reflectors, one of each type at each side. When any vehicle in the combination is 80 in or more in overall width, 3 identification lamps join the rear set. The width trigger looks at the whole combination, not just the rearmost vehicle: a wide towing vehicle triggers the identification lamps on the rear of the towed vehicle.

The intermediate set in paragraph (d) applies to a combination of more than 2 vehicles. The first saddle-mounted vehicle of a double saddle-mount combination is an intermediate vehicle. The first plus second saddle-mount vehicles of a triple saddle-mount combination are intermediate vehicles. Each intermediate vehicle needs 1 side-marker lamp on each side, located near the rear of the vehicle. A 2 vehicle combination has no intermediate vehicle, so the set does not apply. The checker works out whether an intermediate vehicle exists from the combination makeup you enter.

The mobile structure trailer rule in paragraph (c) is a special case. A mobile structure trailer means a trailer that has a roof plus walls, is at least 10 ft wide, plus can be used off road for dwelling or commercial purposes. When such a vehicle runs under a special permit that prohibits operation during the times when lighted lamps are required, it needs only the reduced rear set on the rear: 2 stop lamps, 2 tail lamps, 2 red reflex reflectors, plus 2 turn signals, each pair on either side of the vertical centerline, at the same height, plus as far apart as practicable. At all other times the vehicle must carry the full paragraph (b) set. The reduced set is a daylight-only privilege, not a general exemption.

Lamp sets are a common roadside citation in driveaway work because the towed vehicles are often delivered with their lamps disconnected or unpowered. A driveaway carrier usually runs a temporary lamp bar or a wired lamp set on the rearmost vehicle, powered from the towing vehicle. That temporary set must meet the same counts as a permanent set: 2 of each rear lamp type, plus identification lamps when the width trigger applies. A single tail lamp or a missing turn signal on the rearmost vehicle is a citable defect. The Lighting and Reflector Checker covers the general lamp plus reflector rules that apply to the towing vehicle itself under sections 393.11 plus 393.13.

Which Part 396 rules do not apply to vehicles being delivered?

Section 396.15(a) gives driveaway-towaway operations a narrow but valuable exemption. Every motor carrier, with respect to motor vehicles engaged in driveaway-towaway operations, must comply with the requirements of Part 396, with one exception: maintenance records required by section 396.3, the vehicle inspection report required by section 396.11, plus the periodic inspection required by section 396.17 are not required for any vehicle which is part of the shipment being delivered. The exemption applies to the delivered vehicles only. The towing vehicle keeps every Part 396 duty in full.

Part 396 dutyTowing vehicleVehicle that is part of the shipment
Section 396.3 inspection, repair plus maintenance recordsRequiredNot required
Section 396.11 driver vehicle inspection reportRequiredNot required
Section 396.13 driver inspection before drivingRequiredRequired in the form of the section 396.15(b) pre-trip inspection
Section 396.15(b) pre-trip inspection of the connectionsRequiredRequired
Section 396.15(c) post-trip disassembly plus inspectionRequired for the tow-bars plus saddle-mountsRequired for the tow-bars plus saddle-mounts
Section 396.17 periodic inspectionRequired, at least once every 12 monthsNot required

The logic of the exemption is practical. A new truck being delivered from a factory to a dealer has no maintenance history to record, no driver to file a daily inspection report, plus no 12 month inspection cycle to keep. It is cargo that happens to roll. Requiring a full maintenance file for a vehicle that has never been in service would add paperwork without adding safety. The towing vehicle, by contrast, is in full service, so its records, its driver reports, plus its periodic inspection all stay in force.

The exemption has a hard edge: it covers only vehicles which are part of the shipment being delivered. A vehicle the carrier owns and uses as a towing vehicle, a vehicle being moved to the carrier own terminal for its own use, or a vehicle that has already been delivered plus is being moved again does not qualify. The carrier should be able to show, from the shipping papers or the delivery order, that each towed vehicle is part of the shipment. The checker asks the shipment question directly, plus it reports the exemption result as a figure, so the answer is on the record for the trip file.

The pre-trip inspection in paragraph (b) is not exempted. It is specific to driveaway-towaway work. Before the beginning of any driveaway-towaway operation of motor vehicles in combination, the motor carrier must make a careful inspection and test to ascertain that the tow-bar or saddle-mount connections are properly secured to the towed plus towing vehicle, that they function adequately without cramping or binding of any of the parts, plus that the towed motor vehicle follows substantially in the path of the towing vehicle without whipping or swerving. The third item is a road test, not a visual check: the driver must confirm the towed vehicle tracks true before the trip starts. A combination that whips or swerves on the test must not move until the cause is fixed.

The post-trip inspection in paragraph (c) is also specific to driveaway work. Motor carriers must maintain practices to ensure that following completion of any trip in driveaway-towaway operation of motor vehicles in combination, plus before they are used again, the tow-bars plus saddle-mounts are disassembled plus inspected for worn, bent, cracked, broken, or missing parts. Before reuse, suitable repair or replacement must be made of any defective parts, plus the devices must be properly reassembled. The rule treats the coupling hardware as consumable safety equipment: it is inspected after every trip, not once a year. A carrier that reuses a tow-bar or a saddle-mount without the post-trip disassembly is in violation even when the hardware looks sound from the outside.

The towing vehicle periodic inspection still needs its date tracked. The Annual Inspection Due-Date Tracker works out when the next section 396.17 inspection falls due for the towing vehicle, plus the DVIR Checker covers the daily driver vehicle inspection report the towing vehicle driver must file. The DOT Record Retention Checker works out how long each Part 396 record must be kept, including the maintenance records the towing vehicle generates on every driveaway trip.

What is the conspicuity exception for driveaway-towaway?

Section 393.13(a) excepts trailers transported in a driveaway-towaway operation from the retroreflective sheeting plus reflex reflector requirements for trailers manufactured before December 1, 1993. The section otherwise requires trailers 80 in or more wide with a gross vehicle weight rating of 10,001 lb or more to carry retroreflective sheeting or an array of reflex reflectors on the sides plus the rear. A trailer being delivered as part of a driveaway-towaway operation does not need that conspicuity treatment.

The exception is narrow in two ways. First, it applies to trailers, which is the class section 393.13 covers: a towed truck or bus is not a trailer, so the exception does not change anything for those vehicles. Second, it excepts the trailer from the retroreflective sheeting rules only. It does not except the trailer from the lamp sets in section 393.17. A trailer being delivered in a driveaway-towaway operation still needs the rearmost-vehicle lamp set, or the mobile structure set where that applies, plus the side-markers for its position. A carrier that reads the conspicuity exception as a general lamp exemption is misreading it.

The exception also does not cover the towing vehicle. The towing vehicle is not being transported in a driveaway-towaway operation: it is doing the transporting. Its conspicuity duties, where they apply, stay in force. In practice the towing vehicle is usually a truck tractor, which is not a trailer under section 393.13, so the section rarely touches it. The point stands for any trailer the carrier tows in ordinary service alongside its driveaway work.

Can a vehicle be full-mounted on another vehicle?

Yes, with conditions that depend on where the vehicle is mounted. Section 393.71(b) covers full-mounting on the towing vehicle. A motor vehicle or motor vehicles may be full-mounted on the structure of a towing vehicle engaged in any driveaway-towaway operation when adequately plus securely attached by means equivalent in security to the upper-half attachment rules in paragraph (j)(2). No vehicle may be full-mounted on a towing vehicle unless the relationship of the full-mounted vehicles to the rear axle or axles results in proper distribution of the total gross weight of the vehicles plus does not unduly interfere with the steering, braking, or maneuvering of the towing vehicle, or otherwise contribute to the unsafe operation of the vehicles in the combination.

Section 393.71(c) covers full-mounting on a towed vehicle. It is stricter. A vehicle may be full-mounted on the structure of a towed vehicle when adequately plus securely attached by the same standard. But no vehicle may be full-mounted on a vehicle towed by means of a tow-bar unless the towed vehicle is equipped with brakes plus is provided with means for effective application of brakes acting on all wheels, plus is towed on its own wheels. The tow-bar-towed vehicle carries the full-mounted load on its own wheels, so it must brake for the added weight.

Full-mounting on a saddle-mounted vehicle carries two more conditions. The center line of the kingpin or equivalent attachment of the towed vehicle must be so located on the towing vehicle that the relationship to the rear axle or axles results in proper distribution of the total gross weight plus does not unduly interfere with steering, braking, or maneuvering. In addition, a perpendicular to the ground from the center of gravity of the full-mounted vehicles must lie forward of the center line of the rear axle of the saddle-mounted vehicle. If the full-mounted load sits too far back, its weight lifts the front of the saddle-mounted vehicle plus unloads the kingpin, which is the failure the rule guards against. Finally, a saddle-mounted vehicle carrying a full-mounted vehicle must at all times while so loaded have effective brakes acting on all wheels in contact with the roadway.

The lamp rules follow the load. Section 393.17(b) says that where a vehicle is full-mounted on a saddle-mount vehicle, either the full-mounted vehicle or the rearmost saddle-mounted vehicle must carry the rearmost lamp set. The carrier picks which vehicle carries the set, but one of them must. A full-mounted vehicle that hides the rear lamps of the vehicle under it needs its own lamps, or the combination runs without a visible rear set.

What is the 3-inch tracking rule?

The tracking rule appears twice in section 393.71, once for tow-bars plus once for saddle-mounts, in the same words. Section 393.71(h)(7) says the tow-bar must be so designed, constructed, maintained, plus mounted as to cause the towed vehicle to follow substantially in the path of the towing vehicle. Tow-bars of such design or in such condition as to permit the towed vehicle to deviate more than 3 in to either side of the path of a towing vehicle moving in a straight line as measured from the center of the towing vehicle are prohibited. Section 393.71(m)(3) applies the same 3 in limit to saddle-mounts: towed vehicles must not deviate more than 3 in to either side of the path of the towing vehicle when moving in a straight line.

The measurement is a straight-line test. The towing vehicle drives straight, plus the towed vehicle path is measured against the center of the towing vehicle. A deviation of 3 in or less passes. A deviation of more than 3 in fails, on either side. The test does not ask whether the combination feels stable in a turn: it asks whether the towed vehicle follows the towing vehicle in a straight line. A combination that tracks true in a straight line but whips in a turn has a different problem, which the pre-trip test in section 396.15(b) catches when it requires the towed vehicle to follow without whipping or swerving.

Tracking fails for mechanical reasons. A bent tow-bar, a worn kingpin bushing, a loose U-bolt, a saddle-mount with play in the halves, or a towed vehicle with a steering fault can each push the deviation past 3 in. Tire condition on the towed vehicle matters too: a towed vehicle rolls on its own tires, plus an underinflated or damaged tire on one side pulls the vehicle off line. The Tire Compliance Checker covers the tire rules for every vehicle in the combination. A tracking failure found on the pre-trip test must be fixed before the trip, not noted for later: the section 396.15(b) test is a go or no-go check on the combination.

Tracking is also the most visible driveaway defect on the road. A towed vehicle running a foot off the path of the towing vehicle is obvious to any inspector, any motorist, plus any camera. It signals a worn coupling, a bent bar, or a loose mount, plus it invites a full inspection of the combination. A carrier that checks tracking on every pre-trip test, plus fixes the cause at the first sign of drift, avoids the citation plus the roadside delay that follows it.

How do you use the Driveaway-Towaway Compliance Checker?

Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the verdict change.

  1. Describe the combination: saddle-mounts, tow-bars, plus the heaviest towed vehicle.
  2. Enter the tow-bar rating, the safety chains, plus the tracking deviation.
  3. Enter the saddle-mount figures: U-bolt diameter, kingpin size, lower-half area plus test load.
  4. Answer the lamp questions for the towing vehicle, the rearmost towed vehicle plus any intermediate towed vehicle.
  5. Answer the Part 396 questions: shipment status, pre-trip inspection plus post-trip inspection.
  6. Read the verdict, the failed checks, plus the fix list, then copy the summary for the trip file.

Use the figures from the equipment itself where possible. The best input is the rating stamped on the tow-bar, the diameter measured on the U-bolts plus the kingpin, plus the test load on the saddle-mount plate. Guessing a rating produces a guess. The checker is only as good as the figures entered. When a figure is uncertain, run the tool twice: once with the low figure, once with the high figure. Read the range of results the two runs produce. The range tells you how much the uncertain figure matters.

Read the fix list before the lamp sets section. The fix list names the failed checks in the order the regulation lists them, with the exact figure that failed. A carrier short on time should fix the strength failures first, because a tow-bar or a saddle-mount below its table figure is the failure most likely to cause a separation. A carrier with time should fix every failed check, because a roadside inspector cites each failed item separately.

Questions carriers ask

What is a driveaway-towaway operation?

A driveaway-towaway operation moves an empty or unladen motor vehicle with one or more sets of wheels on the roadway, under the definition in section 390.5T. It covers moves between manufacturer facilities, between a manufacturer plus a dealer or buyer, between a dealer plus a buyer or lessee, to a repair facility after a crash or a component failure, or by means of a saddle-mount or tow-bar. The towed vehicle rolls on its own wheels instead of riding on a trailer.

How many vehicles can a driveaway-towaway combination carry?

Section 393.71(a) allows no more than 3 saddle-mounts plus no more than 1 tow-bar or ball-and-socket device in any combination. The largest combination the caps allow is 5 vehicles: 1 towing vehicle, 1 tow-bar-towed vehicle, plus 3 saddle-mounted vehicles. With triple saddle-mounts, all but the final towed vehicle must have brakes acting on all wheels in contact with the roadway.

How strong must a tow-bar be?

For a towed vehicle of 5,000 lb or more, a new tow-bar needs longitudinal strength of 1.3 times the gross weight of the towed vehicle, plus beam strength of 0.6 times the gross weight when the bar bends in normal operation. A new tow-bar for a vehicle under 5,000 lb needs a flat 6,500 lb of longitudinal strength. A 12,000 lb truck needs a tow-bar rated for at least 15,600 lb.

Do towed vehicles need a periodic inspection?

No, when the vehicle is part of the shipment being delivered. Section 396.15(a) says the section 396.3 maintenance records, the section 396.11 vehicle inspection report plus the section 396.17 periodic inspection are not required for any vehicle which is part of the shipment being delivered. The towing vehicle keeps every Part 396 duty in full, plus the pre-trip inspection plus post-trip disassembly duties in section 396.15(b) and (c) apply to every driveaway-towaway operation.

What lamps does a driveaway-towaway combination need?

Section 393.17 sets a lamp set for each position. The towing vehicle needs 2 headlamps, 2 turn signals plus 2 clearance lamps on the front, 1 side-marker on each side near the front, plus 2 tail lamps plus 2 stop lamps on the rear. The rearmost towed vehicle needs side-markers near the rear plus 2 tail lamps, 2 stop lamps, 2 turn signals, 2 clearance lamps plus 2 reflectors on the rear, plus 3 identification lamps when any vehicle in the combination is 80 in or more wide. Each intermediate towed vehicle needs 1 side-marker on each side near the rear.

Can a bumper tow-bar tow a heavy vehicle?

No. Section 393.71(d) says tow-bars which depend upon the bumpers to transmit forces between the vehicles must not be used to tow a motor vehicle weighing more than 5,000 lb. A bumper tow-bar is legal for a light car only. A heavier vehicle needs a frame-mounted tow-bar rated for the weight under the section 393.71(h)(1) table.

Related tools

Sources

Follow on WhatsApp Ask by Voice