Two pieces of information, both sides, readable from 50 feet. This tool checks your truck door lettering against 49 CFR 390.21T, the federal marking rule. Answer for the marking as it stands today, not as it looked when the truck was lettered. A faded number counts the same as a missing one.
Pick your setup, answer each question, plus read the verdict with the fix list. Every answer updates the result as you change each field.
What does the truck display?
Can it be read?
The rule of thumb is about 1 inch of letter height for every 10 feet of viewing distance. It is a guide, not a regulation: the only test is whether the marking actually reads from 50 feet.
Any other name on the truck?
Compliant. The marking meets 49 CFR 390.21T.
Every check passes: 7 of 7.
The marking meets every element of section 390.21T for this setup. Keep it clean plus legible. Re-check it after any repaint or re-lettering.
The checks
| Check | Result | Detail |
|---|---|---|
| Carrier name | Pass | The legal name of the motor carrier is displayed, as listed on the MCS-150. |
| USDOT number | Pass | The USDOT number is displayed, preceded by the letters USDOT. |
| Both sides | Pass | The marking appears on both sides of the vehicle. |
| Sharp contrast | Pass | The letters contrast sharply in color with the background. |
| Legible from 50 feet | Pass | The marking is readily legible from 50 feet in daylight while the vehicle is stationary. |
| Kept legible | Pass | The marking is kept legible: no fading, peeling, or dirt covering it. |
| Other name on the truck | Pass | No other name appears on the vehicle, so the operated-by rule does not apply. |
The figures
| Figure | Value | Note |
|---|---|---|
| Letter height entered | 5 in | Rule of thumb: about 1 inch of letter height reads at about 10 feet. |
| Estimated legible distance | about 50 ft | Rough guide only. The regulation sets no minimum letter size. The only test is actual legibility from 50 feet in daylight. |
| Required legible distance | 50 ft | Section 390.21T(c)(3): readily legible during daylight hours from 50 feet while the CMV is stationary. |
| Checks passed | 7 of 7 | Every element of section 390.21T for this setup must pass. |
What to fix
- No actions for this result.
Marking checklist
- Carrier legal name or single trade name, exactly as listed on the MCS-150.
- USDOT number, preceded by the letters USDOT.
- Same marking on both sides of the power unit.
- Letters in a color that contrasts sharply with the truck body.
- Letters large enough to read from 50 feet in daylight while the truck is stationary.
- Painted on, or a removable device that meets the same legibility rules.
- If another name appears on the truck, add the words operated by plus the operating carrier name plus USDOT number.
Notes
- The federal rule sets no minimum letter size. The only size test is legibility from 50 feet in daylight while the vehicle is stationary.
- An MC number or MX number is not required on the truck. Only the name plus the USDOT number are required. Extra information is allowed if it does not conflict with the required marking.
- Trailers are not self-propelled, so the door-marking rule does not apply to them. Intermodal equipment has its own marking rule in section 390.21T(g).
- States that adopt the federal rules apply the same marking requirement to intrastate carriers. Some states add their own marking rules on top.
- A marking violation is recorded on the roadside inspection report and stays in the carrier SMS results for 24 months. It is not an out-of-service condition on its own.
This tool applies 49 CFR 390.21T to your inputs. Confirm the result against the regulation text plus your state requirements before acting. The estimator is a sign industry rule of thumb, not a regulation.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is a compliance aid, not legal advice — confirm the marking against the regulation text or your legal counsel before acting on a borderline result.
Quick answer: Every self-propelled commercial motor vehicle in interstate commerce must carry the operating carrier legal name or single trade name plus its USDOT number on both sides, in letters that contrast sharply with the background plus read clearly from 50 feet in daylight. The rule is 49 CFR 390.21T. It sets no minimum letter size: the test is legibility from 50 feet. This checker walks through each element of the rule for your setup, including rented trucks, driveaway service, plus intermodal equipment, then lists exactly what to fix.
What does 49 CFR 390.21T require on the side of a truck?
The federal marking rule is short, plus it is strict about only a few things. Every self-propelled commercial motor vehicle in interstate commerce must carry two pieces of information on both sides: the name of the motor carrier operating it, plus the USDOT number FMCSA issued to that carrier. The letters must contrast sharply with the background, read clearly from 50 feet in daylight while the truck is standing still, plus stay that way. That is the whole rule in one paragraph. The rest of this page works through each element, because the details are where trucks fail inspections.
The rule lives at 49 CFR 390.21T. The T matters. Section 390.21, the version without the T, is suspended indefinitely. The T version has been the rule in force since January 2017, last amended in August 2019. Any guide, sign shop, or checklist that cites 390.21 without the T is citing a suspended section. The text is nearly the same, but the citation on your paperwork should read 390.21T.
| Element | What the rule requires | Citation |
|---|---|---|
| Carrier name | Legal name or a single trade name, as listed on the MCS-150 | 390.21T(b)(1) |
| USDOT number | FMCSA number, preceded by the letters USDOT | 390.21T(b)(2) |
| Other names | Operating carrier identified with the words operated by | 390.21T(b)(3) |
| Placement | Both sides of the self-propelled CMV | 390.21T(c)(1) |
| Contrast | Letters contrast sharply with the background | 390.21T(c)(2) |
| Legibility | Readily legible from 50 feet in daylight, stationary | 390.21T(c)(3) |
| Upkeep | Kept plus maintained so it stays legible | 390.21T(c)(4) |
The checker above tests each row of that table for your setup. It also covers the three special cases the rule writes separately: rented trucks plus leased passenger vehicles, driveaway service, plus intermodal equipment. Pick your setup at the top of the tool, answer the questions, plus read the verdict with the fix list.
Which vehicles must carry DOT markings?
The rule applies to every self-propelled commercial motor vehicle subject to the federal safety regulations. Self-propelled is the key word: the rule covers power units, not trailers. A tractor, a straight truck, a bus, plus a pickup that meets the weight test all count. A trailer does not, because it has no motor of its own.
A vehicle is a commercial motor vehicle under 49 CFR 390.5T if any one of four tests is met:
- It has a gross vehicle weight rating or gross combination weight rating, or gross vehicle weight or gross combination weight, of 10,001 pounds or more, whichever is greater.
- It is designed or used to transport more than 8 passengers, including the driver, for compensation.
- It is designed or used to transport more than 15 passengers, including the driver, not for compensation.
- It transports hazardous material in a quantity that requires placards, whatever its size.
The weight test uses the rating or the actual weight, whichever is greater. A truck rated below 10,001 pounds that is actually loaded past 10,001 pounds is a CMV. A three-quarter-ton pickup hitched to a loaded equipment trailer passes 10,001 pounds combined long before it feels heavy. Owners of pickups plus small straight trucks miss this more than any other group.
The federal rule reaches vehicles in interstate commerce. States that adopt the federal regulations apply the same marking requirement to intrastate carriers, plus most states have adopted them. Some states add their own marking rules on top, such as a state registration number. The checker covers the federal rule only. Check your state requirements separately if you run intrastate.
What name must appear on a commercial motor vehicle?
Section 390.21T(b)(1) gives two choices: the legal name of the motor carrier operating the vehicle, or a single trade name. Single is doing real work in that sentence. A carrier with two trade names on the door fails the rule. Pick one name, plus make it the name on the MCS-150.
The name on the truck must match the name on the MCS-150, the motor carrier identification report. FMCSA reads the door against the registration. A carrier that rebrands, adds a DBA, or shortens its name on the truck without updating the MCS-150 has a mismatch that an inspector can cite. Update the MCS-150 first, then re-letter the truck, or re-letter to the name already on file. The MCS-150 Due Date Checker works out when your next update is due.
If any other person name appears on the truck, the rule adds a step. Section 390.21T(b)(3) says the operating carrier name must be followed by the required information plus preceded by the words operated by. This is the rule behind the operated by line you see on leased trucks plus owner-operator equipment. The point is identification: an inspector, or anyone else, must be able to tell at a glance which carrier is operating the vehicle. A truck that shows a shipper name, a previous owner name, or a dealership name without the operated by line fails the check.
Other identifying information is allowed. Section 390.21T(b)(4) says extra information may be displayed if it is not inconsistent with the required information. A city plus state, a phone number, a unit number, plus a logo are all fine. What is not fine is extra information that contradicts the required marking, such as a second carrier name without the operated by line, or a USDOT number that belongs to someone else.
Does a truck need a USDOT number on both sides?
Yes. The USDOT number goes on both sides of the power unit, with the carrier name, preceded by the letters USDOT. Section 390.21T(b)(2) requires the identification number FMCSA issued to the motor carrier, preceded by the letters USDOT. The letters are part of the marking, not decoration. A bare number with no USDOT in front of it fails.
The most common marking violation in the country is a missing USDOT number. In calendar year 2025, inspectors cited code 390.21TB2DOT, operate a CMV without USDOT number displayed, 61,558 times, making it the 12th most cited violation code of any kind. The missing name code, 390.21TB1MC, was 18th with 55,758 citations. Between them, the two codes account for more than 117,000 citations in one year. Both are fixed with a sign shop visit.
Do not put an MC number on the truck in place of the USDOT number. The marking rule does not require an MC number, an MX number, or a state registration number on the vehicle. Some carriers display an MC number anyway, which is allowed as extra information, but it never substitutes for the USDOT number. If the truck shows an MC number plus no USDOT number, it fails.
The number must be the operating carrier number. A leased truck that shows the lessor USDOT number is using the rental route in section 390.21T(e), which has its own conditions, covered below. A truck that shows a USDOT number belonging to a different carrier, with no rental agreement to support it, fails.
How big must DOT truck lettering be?
The federal rule sets no minimum letter size. Read that again, because it surprises almost everyone. Section 390.21T(c) says the marking must be readily legible during daylight hours from 50 feet while the CMV is stationary. It never says how tall the letters must be. There is no 2-inch rule, no 3-inch rule, plus no font rule in the federal text. The only test is whether a person can read the marking from 50 feet away in daylight.
CVSA, the alliance of enforcement officials who write the inspection standards, confirmed the point in 2024. After a carrier challenged two citations for lettering its inspectors could read, CVSA amended Inspection Bulletin 2021-03 to state that if the proper markings are clearly legible from 50 feet while the vehicle is stationary during daylight hours, a 390.21T(c) violation should not be recorded. Legibility is the test. Letter height is only a means to it.
Contrast matters as much as size. Section 390.21T(c)(2) requires letters that contrast sharply in color with the background. Silver letters on a white truck, dark blue on black, or gold on yellow all fail the contrast test even when the letters are tall. White on a dark cab, black on a white door, plus reflective letters on a dark background all pass easily. If you are choosing colors, pick the combination a stranger could read at a glance from across a parking lot.
The rule of thumb in the checker, about 1 inch of letter height for every 10 feet of viewing distance, is a sign industry guide, not a regulation. By that rough guide, 5-inch letters read at about 50 feet. Real lettering often reads further, because the guide is conservative, plus high-contrast letters on a clean door read better than the guide assumes. Use the estimator as a starting point, then test the real thing: stand 50 feet from the truck in daylight plus read it. That test is the regulation.
Maintenance is part of the rule. Section 390.21T(c)(4) requires the marking to be kept plus maintained so it stays legible. A faded number, a peeling decal, mud across the door, or a winter coat of road film all count the same as a missing marking. Wash the doors, replace peeling vinyl, plus re-check the marking after any repaint. A truck that passed in June can fail in February under a layer of salt plus grime.
Do trailers need a USDOT number?
No. The marking rule covers self-propelled commercial motor vehicles. A trailer has no motor, so it is not self-propelled, plus the door-marking rule does not apply to it. You will see USDOT numbers on plenty of trailers, because carriers paint the fleet number plus the USDOT number on every unit for identification. That is a business choice, not a federal requirement.
The exception is intermodal equipment. Section 390.21T(g) requires each unit of intermodal equipment interchanged to a motor carrier to identify its provider, by legal name or single trade name plus USDOT number. The duty falls on the intermodal equipment provider, not on the carrier hauling the box. The rule allows five methods, covered in the intermodal section below.
Chassis, containers, plus trailers in intermodal service are the equipment this covers. A standard dry van in a carrier own fleet is not intermodal equipment, plus it needs no marking under the federal rule. If you are unsure whether a unit counts as intermodal equipment, the test is whether an intermodal equipment provider interchanges it to a carrier. If the carrier owns the trailer outright plus it never changes hands through an interchange, the (g) rule does not reach it.
What are the marking rules for a rented truck?
Section 390.21T(e) covers rented CMVs plus leased passenger-carrying CMVs when the rental agreement or lease runs 30 calendar days or fewer. It offers two routes. Route one: mark the truck with the operating carrier own name plus USDOT number, exactly as if the carrier owned it. Route two: keep the lessor name plus lessor USDOT number on the truck, plus carry a rental agreement that contains the information the rule lists. Either route complies. The checker tests both.
Route two has six conditions, plus all six must hold:
- The lessor legal name or single trade name is displayed on the truck under the size, contrast, plus legibility rules.
- The lessor USDOT number is displayed the same way.
- The rental agreement conspicuously contains the renter name plus the complete physical address of its principal place of business.
- The agreement contains the renter USDOT number, or in its place, whether the renter is engaged in interstate or intrastate commerce plus whether the renter is transporting hazardous materials in the rented CMV.
- The agreement contains the cooperation sentence, word for word.
- The agreement is carried on the CMV for the full term of the rental or lease.
The cooperation sentence, word for word, reads: “This lessor cooperates with all Federal, State, and local law enforcement officials nationwide to provide the identity of customers who operate this rental or leased CMV”. Put it in the agreement exactly as printed. A paraphrase does not comply.
The 30-day limit counts calendar days. A 31-day rental cannot use route two at all. The truck must carry the operating carrier own marking. Rental companies that write 30-day agreements with automatic renewals should note that the term is the term of the agreement, not the billing cycle. If the agreement runs past 30 days, route two closes.
The most cited rental marking failures in 2025 were the missing agreement on board (code 390.21TE2IVD, 3,994 violations) plus the missing agreement information (code 390.21TELCMVINFO, 3,105 violations). Both are paperwork failures, not lettering failures. The truck was marked. The paper was not in the cab. Put the agreement in the truck before it leaves the lot.
Passenger carriers get one more exception. A passenger-carrying CMV operating under the 48-hour emergency exception in section 390.403(a)(2) does not need the agreement items in (e)(2)(iii) plus (iv), provided the lessor plus lessee meet the 390.403(a)(2) conditions. That exception covers emergency replacement equipment, not routine leases. A carrier setting up a new passenger operation should also confirm its process agent filing with the BOC-3 Coverage Checker.
What are the marking rules for driveaway services?
Driveaway service moves vehicles by driving them, one at a time or in combination, to the buyer or the next carrier. The vehicle being delivered is the load plus the truck at the same time, so painting the carrier name on every unit is not practical. Section 390.21T(f) answers with a removable device.
The device may be affixed on both sides or at the rear of a single driven vehicle. In a combination driveaway operation, it may go on both sides of any one unit or at the rear of the last unit. One side alone does not comply. The rear option is the one driveaway operators use most, because a single placard at the back covers the whole movement.
The device must display the legal name or a single trade name of the motor carrier plus the motor carrier USDOT number. The same two pieces of information as a painted marking, on a board that moves from one vehicle to the next. The checker tests placement, content, plus legibility for both single plus combination operations.
Driveaway marking failures are rare in the inspection data: code 390.21TF was cited 45 times in 2025. The rarity is a sign that the removable-device rule works. A driver who forgets the board entirely is the usual failure, plus it is fixed by keeping a spare board in the chase vehicle.
How is intermodal equipment marked?
Section 390.21T(g) puts the duty on the intermodal equipment provider, the company that owns the chassis or container plus interchanges it to a motor carrier. Each unit interchanged or offered for interchange must identify the provider by legal name or single trade name plus USDOT number. The rule then offers five methods, plus any one of them complies.
| Method | What it requires |
|---|---|
| Curb-side marking, (g)(4)(i) | Marking on the curb side, sharp contrast, legible from 50 feet in daylight, kept legible |
| Curb-side label, (g)(4)(ii) | Label on the curb side, readily visible plus legible to an inspection official in daylight while stationary, sharp contrast on the label plus the letters, kept legible |
| Interchange agreement, (g)(4)(iii) | USDOT number on the interchange agreement, clearly identifiable to an inspection official, plus VIN plus 4-character SCAC code plus 6-digit unique identifying number |
| Weathertight document, (g)(4)(iv) | Marking on a document in a weathertight compartment affixed to the frame, sharp contrast, plus VIN plus SCAC plus 6-digit number |
| Real-time database, (g)(4)(v) | USDOT number in a database with real-time internet plus telephonic access, read-only, no registration, no password, no fee, answering by SCAC plus trailing digits, by plate plus State, or by VIN |
The database method is the one most providers use at scale. It has real conditions: the database must answer inquiries on individual units, it must be reachable in real time by internet plus telephone, plus access must be read-only with no advance registration, no password, plus no usage fee. A database behind a login wall does not comply.
Intermodal marking failures are uncommon: the largest code, 390.21TG3IEP, was cited 217 times in 2025. When they happen, the usual cause is a unit that changed providers without its identification changing with it. The provider on the equipment must be the provider responsible for it now, not the one that owned it last year.
What happens if a truck is not marked correctly?
The immediate consequence is a violation on the roadside inspection report. In calendar year 2025, inspectors cited 159,844 violations under the 390.21 codes, out of 5,612,687 violations of all kinds. Marking violations are about 2.8 percent of everything inspectors write. Two of them sit in the top 20 codes in the country: no USDOT number displayed at 12th, no name displayed at 18th. For a rule that takes a sign shop visit to satisfy, it is cited far too often.
The violation stays in the carrier SMS results for 24 months, weighted most heavily while it is recent: three times weight in the first 6 months, twice from 6 to 12 months, once from 12 to 24 months. A marking violation on its own will not push a carrier over an intervention threshold, but it adds to the pile, plus it is the easiest violation in the book to prevent. The CSA Violation Points Checker shows how a violation counts in the SMS math. The DataQs Challenge Helper covers the challenge process if a citation is wrong. The Safety Rating Explainer shows how inspection violations feed the safety rating process.
A marking violation on its own is not an out-of-service condition. The CVSA out-of-service criteria do not list marking as a defect that stops a vehicle. The truck keeps rolling, with a violation on its record. That is not a reason to ignore it. An inspector who finds a missing USDOT number often looks harder at the rest of the truck, plus the marking violation is frequently the first line on a longer report.
FMCSA can also assess civil penalties for violations of the safety regulations, under the penalty schedule in Part 386 Appendix B. The FMCSA Fine Calculator works out the maximum for a given violation. A single marking violation rarely draws a standalone penalty, but a pattern of marking failures found in an investigation can. The cheapest fix is a decal, not a defense.
If a citation is wrong, challenge it. CVSA guidance says a 390.21T(c) violation should not be recorded when the markings are clearly legible from 50 feet in daylight while the vehicle is stationary. If your lettering reads from 50 feet plus the citation says otherwise, photographs taken from 50 feet, plus the bulletin language, are the core of a DataQs request. Keep the photos from the day, not from a re-lettering done later.
How do you use the Vehicle Marking Checker?
Work through the fields in order. The tool updates with every change, so you can fix an answer plus watch the verdict change.
- Pick your setup: your own truck, a rented truck, a leased passenger vehicle, driveaway service, or intermodal equipment.
- Answer each question about the marking as it stands today.
- Enter the letter height in inches for the legibility estimate.
- Read the verdict, the checks, plus the figures.
- Work through the fix list, starting with the failed items.
- Copy the summary plus the checklist for the sign shop or the file.
Use the tool before a truck goes back on the road after a repaint, a re-lettering, or a change of carrier name. The five minutes it takes are cheaper than the citation. The checklist at the bottom of the results is written to hand to a sign shop: it lists everything the marking must show, in the order the rule lists it.
Questions carriers ask
What is the DOT truck lettering requirement?
Every self-propelled commercial motor vehicle in interstate commerce must display the operating carrier legal name or single trade name plus its USDOT number on both sides, in letters that contrast sharply with the background plus read clearly from 50 feet in daylight. The rule is 49 CFR 390.21T. Trailers are not covered, because they are not self-propelled.
How big do DOT numbers have to be on a truck?
The federal rule sets no minimum letter size. Section 390.21T(c)(3) requires only that the marking be readily legible during daylight hours from 50 feet while the CMV is stationary. A common sign industry guide says about 1 inch of letter height reads at about 10 feet, which points to 5-inch letters for the 50-foot test, but the guide is not a regulation. The only test is whether the marking actually reads from 50 feet.
Does a trailer need a USDOT number on it?
No. The marking rule in section 390.21T covers self-propelled commercial motor vehicles only. A trailer needs no USDOT number under the federal rule. The exception is intermodal equipment, which must identify its provider under section 390.21T(g), by one of five methods.
Can I use a magnetic sign for my DOT number?
Yes, if it meets the rule. Section 390.21T(d) allows the marking to be painted on the CMV or to consist of a removable device, as long as the device meets the identification plus legibility requirements in section 390.21T(c). A magnetic sign is a removable device. It must sit on both sides, contrast sharply, read from 50 feet, plus stay legible. A sign that slides, peels, or blows off fails the maintenance rule.
Do I need my MC number on the truck?
No. The marking rule requires only the carrier name plus the USDOT number. An MC number is not required on the vehicle. You may display one as extra information, under section 390.21T(b)(4), but it never substitutes for the USDOT number.
What happens if my truck fails a marking inspection?
The inspector records a violation on the inspection report, under one of the 390.21T codes. The violation stays in the carrier SMS results for 24 months. It is not an out-of-service condition on its own, so the truck keeps rolling. In calendar year 2025, inspectors cited 159,844 marking violations, with a missing USDOT number the 12th most cited violation code in the country.
Related tools
- MCS-150 Due Date Checker: the name on the truck must match the MCS-150. Work out when your next update is due.
- BOC-3 Coverage Checker: check the process agent filing that sits beside the USDOT number in every new carrier setup.
- FMCSA Fine Calculator: work out the maximum civil penalty for a safety regulation violation.
- CSA Violation Points Checker: see how a roadside violation counts in the SMS math.
- DataQs Challenge Helper: challenge a citation that is wrong, with the steps plus the deadlines.
- Safety Rating Explainer: see how inspection violations feed the safety rating process.
Sources
- 49 CFR 390.21T, Marking of self-propelled CMVs and intermodal equipment (eCFR, read verbatim Nov 19, 2026; last amended 84 FR 40294, Aug 14, 2019)
- 49 CFR 390.5T, Definitions (eCFR, read verbatim Nov 19, 2026; commercial motor vehicle definition)
- 49 CFR 390.19T, Motor carrier identification report (eCFR, confirmed Nov 19, 2026)
- CVSA Operational Policy 15, issue 24-040-DRV, guidance for 390.21T (CVSA, Jul 2024; Inspection Bulletin 2021-03 clarification)
- FMCSA Analysis and Information, Roadside Inspection Violations (calendar year 2025, MCMIS snapshot 30 Oct 2026)