Every required lamp must work at all times. A lamp that is out, a reflector that is missing and tape that is faded are all violations under 49 CFR 393.9, even in daylight. Check the lamps before every trip.
Answer for one vehicle. Every answer updates as you change each field.
The vehicle
Overall width is the nominal design width of the widest part of the vehicle, not counting signal lamps, marker lamps, mirrors, flexible fender extensions and mud flaps. The 1993 question matters only for trailers: it picks the conspicuity rule.
The combination
The towing question applies to truck tractors only. It decides the license plate lamp exception. The dolly question applies to converter dollies only. A driveaway-towaway combination follows section 393.17 instead of Table 1.
The load
A projecting load needs extra lamps under Table 1 footnotes 9 and 10, in addition to the lamps on the vehicle itself. The extra lamps are required when the vehicle runs during the hours when headlamps are required to be used.
Condition of the lamps
Check complete: all required lamps and reflectors are in order
Every required lamp and reflector for this vehicle is present and working. No conspicuity treatment is required for this vehicle.
Required lamps and reflectors
| Item | Status | Quantity, color, position and height |
|---|---|---|
| Headlamps | OK | 2, White, Front, 22 to 54 in |
| Turn signal lamps (front) | OK | 2, Amber, At or near the front, 15 to 83 in |
| Identification lamps (front) | OK | 3, Amber, Front, near the top, As close as practicable to the top |
| Tail lamps | OK | 2, Red, Rear, 15 to 72 in |
| Stop lamps | OK | 2, Red, Rear, 15 to 72 in |
| Clearance lamps (front) | OK | 2, Amber, Front, As high as practicable |
| Reflex reflectors (rear) | OK | 2, Red, Rear, 15 to 60 in |
| Reflex reflectors (front side) | OK | 2, Amber, Each side, as far to the front as practicable, 15 to 60 in |
| License plate lamp (rear) | Not required | 1, White, At the rear license plate, No height requirement |
| Side marker lamps (front) | OK | 2, Amber, Each side, as far to the front as practicable, 15 in or higher |
| Turn signal lamps (rear) | OK | 2, Amber or red, Rear, 15 to 83 in |
| Hazard warning signal lamps (front) | OK | 2, Amber, Front, 15 to 83 in |
| Hazard warning signal lamps (rear) | OK | 2, Amber or red, Rear, 15 to 83 in |
| Backup lamp | OK | 1 or 2, White, Rear, No height requirement |
| Lamps and reflectors not obscured | Clear | No lamp or reflector is obscured by the load, tailboard, dirt or equipment. |
Conspicuity treatment
| Requirement | Rule and pattern | Status |
|---|---|---|
| Conspicuity treatment | Not required Section 393.11(b) applies to trailers. A truck tractor is not a trailer for this rule. | Not applicable |
What to fix before you drive
- No fixes needed on these answers. Recheck the lamps and reflectors at the next pre-trip inspection (49 CFR 392.7).
Notes
- No rear license plate lamp is required on a truck tractor while it is towing a trailer (Table 1 of section 393.11, footnote 11, added by FR Doc 2026-03259, effective March 23, 2026). The lamp is required again when the tractor runs without a trailer.
This checker applies Table 1 of 49 CFR 393.11 and the related sections to your answers. It is not legal advice. Confirm the vehicle type and the manufacture date with the vehicle plate before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice โ check the current regulation and your company policy before you rely on a result.
Quick answer: A truck or trailer must carry the lamps and reflectors in Table 1 of 49 CFR 393.11 for its type, with headlamps 22 to 54 inches high and tail and stop lamps 15 to 72 inches high. Trailers 80 inches or wider with a GVWR over 10,000 pounds need a conspicuity treatment: red and white tape or reflectors on the rear and sides. Since March 23, 2026, a truck tractor needs no rear license plate lamp while it is towing a trailer. This checker builds the required list and flags every missing or broken item.
What lamps does a truck need under DOT rules?
Table 1 of 49 CFR 393.11 lists every lamp and reflector a commercial motor vehicle must carry, with the quantity, color, position and mounting height of each item for each of the eight vehicle types, lettered A through H. A truck tractor needs a different set from a semi-trailer. A narrow truck needs a different set from a wide one. The checker above builds the list for your vehicle from that table.
The eight types are simple once you know them. Type A covers buses and trucks under 80 inches wide. Type B covers buses and trucks 80 inches or wider. Type C covers truck tractors. Type D covers semitrailers and full trailers 80 inches or wider, except converter dollies.
Type E covers converter dollies. Type F covers semitrailers and full trailers under 80 inches wide. Type G covers pole trailers. Type H covers projecting loads.
Most trucks on the road today are type B, type C or type D. A standard 102-inch wide tractor-trailer is a type C tractor pulling a type D trailer. Each unit carries its own set of lamps. The tractor needs headlamps, turn signals, identification lamps, tail lamps, stop lamps, clearance lamps, side markers, reflectors, hazard flashers and a backup lamp. The trailer needs its own tail lamps, stop lamps, turn signals, clearance lamps, side markers, reflectors and identification lamps.
Vehicles made on or after December 25, 1968 must also meet FMVSS 108, the federal lighting standard in effect when the vehicle was made. Older vehicles must meet the Part 393 rules in effect at the time of manufacture. In practice the Table 1 list and the FMVSS 108 list match for almost every vehicle on the road today.
What lights are required on a truck tractor?
A truck tractor is type C. It needs two white headlamps, two amber front turn signals, three amber front identification lamps, two red tail lamps, two red stop lamps, two amber front clearance lamps, two red rear reflex reflectors, two amber front side reflex reflectors, one white rear license plate lamp, two amber front side marker lamps, two rear turn signals, front and rear hazard warning lamps and one or two white backup lamps.
Two absences surprise drivers. A tractor needs no rear clearance lamps: Table 1 gives rear clearance lamps to types B, D, G and H only. A tractor needs no rear identification lamps either: those belong to types B, D and G. The three amber lamps across the top of the cab are the front identification lamps. They are required.
The license plate lamp has a new exception. Since March 23, 2026, no rear license plate lamp is required on a truck tractor while it is towing a trailer. The exception sits in footnote 11 of Table 1. It does not remove the lamp from the tractor: the lamp is required again when the tractor runs without a trailer.
The tractor also needs a hazard warning system that flashes all four turn signals at once, with a switch that works whether the ignition is on or off. That is 49 CFR 393.19. A tractor with a dead hazard switch fails the check even when every turn signal works on its own.
What lights are required on a semi-trailer?
A standard 53-foot semi-trailer is type D. It needs two red tail lamps, two red stop lamps, two amber front clearance lamps, two red rear clearance lamps, two amber intermediate side reflex reflectors, two red rear reflex reflectors, two red rear side reflex reflectors, two amber front side reflex reflectors, one white rear license plate lamp, two amber front side marker lamps, two amber intermediate side marker lamps, two red rear side marker lamps, two rear turn signals, three red rear identification lamps and two rear hazard warning lamps.
Length changes the list. Intermediate side marker lamps and intermediate side reflex reflectors are required only when the vehicle is more than 30 feet long. A 33-foot pup trailer needs them. A 20-foot container chassis does not. The checker adds the intermediate items when the length you enter is over 30 feet.
Rear side marker lamps have their own height rule. On a semitrailer or full trailer made on or after March 1, 1979, the rear side marker lamps sit at least 15 inches above the road. On the rear of the trailer they sit no more than 60 inches above the road. That is footnote 4 of Table 1. Older trailers follow the general 15-inch minimum.
A short trailer gets a break. A trailer under 6 feet long, including the tongue, needs no front side marker lamps and no front side reflex reflectors. That is footnote 16. The rule covers small utility trailers, not the trailers most carriers run.
How high must truck lights be mounted?
Heights are measured from the center of the lamp to the road surface, with the vehicle at curb weight. Curb weight means the vehicle as it stands, without cargo and without a driver. A lamp that sits at the right height when the trailer is empty may sit lower when the trailer is loaded. The rule measures the empty height.
Headlamps sit 22 to 54 inches high. Tail lamps and stop lamps sit 15 to 72 inches high. Turn signals and hazard warning lamps sit 15 to 83 inches high.
Reflex reflectors sit 15 to 60 inches high. Side marker lamps sit at least 15 inches high. Rear side marker lamps on trailers sit no more than 60 inches high. Clearance lamps sit as high as practicable. Identification lamps sit as close as practicable to the top of the vehicle.
The license plate lamp and the backup lamp have no height requirement. The plate lamp must light the plate from the top or the sides. The backup lamp must operate when the vehicle is in reverse. No rule fixes where either lamp sits.
The table below gives the heights at a glance. Use the checker above for the full list for your vehicle type.
| Lamp or reflector | Height above the road |
|---|---|
| Headlamps | 22 to 54 in |
| Tail lamps | 15 to 72 in |
| Stop lamps | 15 to 72 in |
| Turn signal lamps | 15 to 83 in |
| Hazard warning lamps | 15 to 83 in |
| Reflex reflectors | 15 to 60 in |
| Side marker lamps | 15 in or higher |
| Clearance lamps | As high as practicable |
| Identification lamps | As close as practicable to the top |
| License plate lamp | No height requirement |
| Backup lamp | No height requirement |
What is the DOT conspicuity tape requirement?
Conspicuity treatment is the red and white reflective tape or reflectors on the rear and sides of a trailer. Section 393.11(b) requires it on every trailer 80 inches or wider with a GVWR over 10,000 pounds, made on or after December 1, 1993. Pole trailers and trailers designed exclusively for living or office use are excepted.
The pattern has three parts. On the rear, a strip of alternating red and white sheeting runs across the full width of the trailer, with its centerline 15 to 60 inches above the road. Two pairs of white strips, each 12 inches long, sit horizontally and vertically at the upper rear corners. On each side, strips run from near the front to near the rear, covering at least half the trailer length in total, with the centerline 15 to 60 inches high.
Sheeting, reflectors or a mix of both all count, as long as the material meets FMVSS 108. The tape you buy in a truck stop is usually Grade DOT-C2, which is the standard grade for trailers. Look for the DOT-C2 mark on the tape. Unmarked tape may not meet the standard. Faded tape that no longer reflects does not meet it either.
Conspicuity material can also take the place of reflex reflectors. Section 393.11(a)(2) says a trailer with conspicuity material needs no separate reflex reflectors where the material sits at the reflector locations and meets the visibility requirements. The tape does the job of the reflector in that spot. Where there is no tape, the reflector is still required.
Truck tractors carry conspicuity too, but under a different rule. FMVSS 108 requires conspicuity treatment on new truck tractors at manufacture: strips on the rear fenders or mudflaps, plus white strips at the upper cab contours. That is a manufacturing standard. The FMCSR in-service duty in section 393.11(b) applies to trailers only, so the checker tests tractors for lamps and reflectors, not for tape.
What are the rules for trailers built before December 1993?
Trailers made before December 1, 1993 follow section 393.13 instead of section 393.11(b). The rule covers trailers 80 inches or wider with a GVWR of 10,001 pounds or more. Offices, dwellings, pole trailers and trailers moved in a driveaway-towaway operation are excepted.
The pattern matches the newer rule in most respects. The sheeting must be at least 2 inches wide. Side strips on each side must total at least half the trailer length, with the centerline 15 to 60 inches above the road when the trailer is empty. The rear needs a full-width strip at the same height, plus two pairs of 12-inch white strips at the upper rear corners.
Reflector arrays are an alternative to sheeting. Each reflector center must sit no more than 4 inches from the center of the next reflector in the array. The arrays follow the same locations as the sheeting: sides, lower rear and upper rear corners.
The section encourages carriers to retrofit older trailers to the full FMVSS 108 pattern, with red and white material throughout. A trailer retrofitted that way meets both rules at once. The checker applies section 393.13 when the year of manufacture is before December 1993 and section 393.11(b) when it is after.
Does a truck tractor need a license plate lamp while towing?
No. Since March 23, 2026, no rear license plate lamp is required on a truck tractor while it is towing a trailer. The change came in FR Doc 2026-03259, published February 19, 2026, which rewrote footnote 11 of Table 1. The footnote now reads: no rear license plate lamp is required on vehicles that do not display a rear license plate or on the rear of truck tractors while towing a trailer.
The scope is narrow. The narrow scope matters. The exception covers the rear of a truck tractor only while it is towing a trailer. It does not cover the trailer: the trailer still needs its own rear license plate lamp. It does not cover a tractor running without a trailer: a bobtail tractor needs the lamp. It does not remove the plate itself: the tractor must still display its plate.
The same footnote covers vehicles that do not display a rear license plate at all. A vehicle with no rear plate needs no rear plate lamp. That part of the footnote is older law. The 2026 change added the tractor-while-towing clause.
Check the date before you rely on an older guide. Articles written before March 2026 say every tractor needs a rear plate lamp. That was true until the rule changed. The checker applies the current footnote and marks the lamp Not required when the tractor is towing.
What lights does a projecting load need?
A load that sticks out past the sides or the rear of the vehicle needs extra lamps, on top of the lamps the vehicle already carries. Table 1 calls a projecting load type H. The extra lamps mark the edges of the load so other drivers can see how far it sticks out.
A load that extends more than 4 inches beyond the overall width of the vehicle needs lamps at its edges. The foremost edge of the projection gets an amber lamp, visible from the front and the side. The rearmost edge gets a red lamp, visible from the rear and the side. That is footnote 9.
A short projection gets a simpler treatment. If the projecting load measures no more than 3 feet from front to rear, one amber lamp marks it, visible from the front, both sides and rear. If the projection sits at or near the rear of the vehicle, the single lamp is red instead of amber.
A load that extends more than 4 feet beyond the rear of the vehicle needs more. Each side of the projection gets a red side marker lamp, placed to show the maximum overhang. The rear of the projection gets two red lamps and two red reflectors, one of each on each side, placed to show the maximum width. Tailboards and tailgates that extend more than 4 feet beyond the body count the same as a load.
Two practical points. The projecting-load lamps are required only when the vehicle runs during the hours when headlamps are required to be used. In daylight they are not required, though many carriers fit them anyway. Battery-powered lamps are allowed on projecting loads: section 393.23 excepts them from the rule that all required lamps run off the vehicle electrical system.
Can a lamp be obscured by the load?
No. Section 393.9(b) says lamps and reflective devices required by Part 393 must not be obscured by the tailboard, by any part of the load, by its covering, by dirt, by other added vehicle or work equipment, or otherwise. Section 392.33 says the same thing from the driver side: no commercial motor vehicle may be driven when a required lamp or reflector is obscured.
Dirt counts: a tail lamp caked in mud is obscured, so washing it is part of the pre-trip inspection. A tarp strap across a side marker lamp counts. A load that hangs past the rear lamps counts. The rule does not care why the lamp is covered. It cares that other drivers cannot see it.
One exception exists. Conspicuity treatments on front-end protection devices may be obscured by part of the load being transported. That is the only exception in either section. It does not cover tail lamps, turn signals, reflectors or tape anywhere else on the vehicle.
Equipment that blocks a lamp needs an auxiliary lamp. Section 393.25(b) says that when motor vehicle equipment such as mirrors, snow plows, wrecker booms, backhoes or winches prevents a required lamp from meeting the visibility rules, an auxiliary lamp meeting the rules must be provided. The auxiliary lamp does the job the blocked lamp cannot do.
What lamps does a driveaway-towaway combination need?
A driveaway-towaway operation moves vehicles by towing them, one behind another, instead of hauling them on a trailer. Section 393.17 gives these combinations their own lamp sets, which replace Table 1 for the vehicles in the combination.
The towing vehicle needs at least two headlamps, two turn signals and two clearance lamps on the front, one side marker lamp on each side near the front. The rear needs two tail lamps and two stop lamps. That is section 393.17(a).
The rearmost towed vehicle needs one side marker lamp on each side near the rear. On the rear it needs two tail lamps, two stop lamps, two turn signals, two clearance lamps and two reflectors, one of each on each side. When any vehicle in the combination is 80 inches or wider, the rearmost vehicle also needs three identification lamps on the rear. That is section 393.17(b).
An intermediate towed vehicle needs only one side marker lamp on each side, near the rear. That is section 393.17(d). Mobile structure trailers have their own set in section 393.17(c): with a special permit that bars night operation, the rear needs two stop lamps, two tail lamps, two red reflectors and two turn signals.
Do all required lamps have to work at all times?
Yes. Section 393.9(a) says all lamps required by Part 393 must be capable of being operated at all times. A lamp that works only sometimes is a violation. The rule does not require auxiliary or additional lamps to work at all times, but every lamp Table 1 requires must work.
The driver checks them before every trip. Section 392.7 requires the driver to be satisfied that the lighting devices and reflectors are in good working order before driving. A pre-trip inspection that skips the lamps skips a federal duty. The Pre-Trip Inspection Checklist walks through the full check, including the lamp items.
Three more rules shape the answer. No commercial motor vehicle may carry an amber stop lamp or tail lamp: section 393.11(c) bans them. All exterior lamps must be steady-burning, except turn signals, hazard flashers and the warning lamps the rule names: section 393.25(e).
Stop lamps must light when the service brakes are applied: section 393.25(f).
Combination rules limit how lamps share a housing. A turn signal lamp must not be combined optically with a headlamp or with a brighter lamp. It must not be combined with a stop lamp unless the stop lamp function switches off when the turn signal is on. A clearance lamp must not be combined with a tail lamp or an identification lamp. That is section 393.22.
A pre-trip inspection covers more than lamps. Tires have their own tread depth and condition rules. Emergency equipment has its own list. The Tire Compliance Checker tests tread depth against section 393.75. The Emergency Equipment Checker tests fire extinguishers and warning devices against the current rules.
What happens at a roadside inspection when a lamp is out?
The inspector cites the violation under the section that fits: section 393.9 for a lamp that is not operable, section 393.11 for a lamp that is missing, section 392.33 for a lamp that is obscured. The citation goes on the inspection report and on the carrier record.
A lighting violation also affects the carrier safety score. Each violation carries a severity weight in the Vehicle Maintenance BASIC of the CSA Safety Measurement System. The CSA Violation Points Checker shows the severity weight, the BASIC and the day the violation falls off the 24-month window.
A wrong citation can be challenged. A violation recorded in error can be contested through a Request for Data Review in DataQs. The DataQs Challenge Helper walks through the three-stage review and the deadlines for each stage.
A lighting violation can also draw a civil penalty. The FMCSA Fine Calculator shows the maximum penalty for a violation under 49 CFR Part 386, with the exact citation and the next steps.
The cheapest fix is the pre-trip check. A lamp that is out in the yard costs a bulb and ten minutes. The same lamp at a scale house costs a violation, points on the carrier record and a delay while the driver fixes it or waits for a repair. Check the lamps before every trip. Fix what is out before the truck moves.
How do you use the Lighting and Reflector Checker?
- Pick the vehicle type from Table 1: bus or truck, truck tractor, trailer, converter dolly or pole trailer.
- Enter the overall width, GVWR, overall length and year of manufacture.
- Answer the combination questions: towing, rear plate, dolly, living or office use and driveaway-towaway.
- Say whether the load projects beyond the side or the rear of the vehicle.
- Mark the condition of each lamp group and the conspicuity treatment.
- Read the required list, the conspicuity verdict and the fix list, then copy the summary for your records.
Frequently asked questions
What lights are required on a semi truck?
A truck tractor needs two white headlamps, two amber front turn signals, three amber front identification lamps, two red tail lamps, two red stop lamps, two amber front clearance lamps, two red rear reflex reflectors, two amber front side reflex reflectors, two amber front side marker lamps, two rear turn signals, front and rear hazard warning lamps and one or two white backup lamps. Since March 23, 2026, no rear license plate lamp is required while the tractor is towing a trailer.
How many lights are required on a trailer?
A standard 53-foot semi-trailer needs two tail lamps, two stop lamps, four clearance lamps, two intermediate side marker lamps, two front side marker lamps, two rear side marker lamps, two rear turn signals, three rear identification lamps, two rear hazard warning lamps, one rear license plate lamp and eight reflex reflectors, plus a conspicuity treatment on the rear and sides. Shorter trailers need fewer items: intermediate markers apply only over 30 feet.
Is conspicuity tape required on all trailers?
No. Conspicuity treatment is required only on trailers 80 inches or wider with a GVWR over 10,000 pounds. Trailers made on or after December 1, 1993 follow section 393.11(b) and FMVSS 108, while earlier trailers follow section 393.13. Pole trailers and trailers designed exclusively for living or office use are excepted under both rules.
Does a truck tractor need a license plate light when towing?
No. Since March 23, 2026, no rear license plate lamp is required on the rear of a truck tractor while it is towing a trailer. The exception is footnote 11 of Table 1 of 49 CFR 393.11, added by FR Doc 2026-03259. The lamp is required again when the tractor runs without a trailer. The trailer still needs its own rear license plate lamp.
What is the minimum height for truck tail lights?
15 inches. Tail lamps and stop lamps must sit between 15 and 72 inches above the road surface, measured from the center of the lamp with the vehicle at curb weight. Both lamps on an axle sit on the same level, as far apart as practicable.
Can you drive with a broken tail light on a truck?
No. Section 393.9(a) requires every lamp in Table 1 to work at all times, so a broken tail light is a violation even in daylight. Section 392.7 requires the driver to check the lighting devices before driving. Fix it before the truck moves.
Related tools
- Pre-Trip Inspection Checklist: walk through the full pre-trip inspection, including the lamp and reflector items.
- Tire Compliance Checker: test tread depth and tire condition against section 393.75.
- Emergency Equipment Checker: check fire extinguishers and warning devices against the current rules.
- CSA Violation Points Checker: pick a violation and its date to see the severity weight, the BASIC, the time weight and the day it falls off the 24-month SMS window.
- DataQs Challenge Helper: challenge a violation or crash recorded in error, with the three-stage review and its deadlines.
- FMCSA Fine Calculator: check the maximum FMCSA fine for any violation under 49 CFR Part 386, with the exact citation and next steps.
- Trucking Tools: browse every free calculator on Trucking Mind.
Sources
- 49 CFR 393.11, Lamps and reflective devices. ecfr.gov/current/title-49/section-393.11 Accessed November 19, 2026.
- 49 CFR 393.13, Retroreflective sheeting and reflex reflectors for trailers manufactured before December 1, 1993. ecfr.gov/current/title-49/section-393.13 Accessed November 19, 2026.
- 49 CFR 393.9, Lamps operable, prohibition of obstructions of lamps and reflectors. ecfr.gov/current/title-49/section-393.9 Accessed November 19, 2026.
- 49 CFR 393.17, Lamps and reflectors, combinations in driveaway-towaway operation. ecfr.gov/current/title-49/section-393.17 Accessed November 19, 2026.
- 49 CFR 392.33, Obscured lamps or reflective devices/material. ecfr.gov/current/title-49/section-392.33 Accessed November 19, 2026.
- 49 CFR 571.108, Standard No. 108, Lamps, reflective devices and associated equipment (conspicuity systems, S8.2). ecfr.gov/current/title-49/section-571.108 Accessed November 19, 2026.
- FR Doc 2026-03259, Parts and Accessories Necessary for Safe Operation; License Plate Lamps, 91 FR 7873, published February 19, 2026, effective March 23, 2026. federalregister.gov/documents/2026/02/19/2026-03259 Accessed November 19, 2026.