This tool recommends a permit family. It does not issue a permit. Every state on the route issues its own permit, with its own limits, fees, plus travel rules. Confirm the result with the permit office in each state before moving the load.
Measure the load as it will travel, then answer the six questions. Every answer updates the result as you change each field. Width, height, plus length are in feet. Weight is in pounds.
The load
Measure the load as it will travel, including overhang plus attachments. Enter decimals where needed: 12.5 means 12 feet 6 inches. Gross weight is the whole combination as it will travel.
The load type
A load is non-divisible when splitting it would ruin its use, destroy its value, or take more than 8 work-hours to dismantle. Routine OS/OW permits exist for non-divisible loads. Pick Not sure when the answer is unclear.
The lane
Count the trips on this lane in a year, not all the trips the truck runs. The regional permit check uses the GAO 2015 membership list. Pick Other or mixed when the route runs outside those regions or crosses between them.
Verdict: Regional multi-state permit.
The WASHTO Western Regional Permit fits this load.
This load fits the published WASHTO limits, so one regional permit can cover the member states on the route instead of a separate permit from each state. The regional permit is a single-trip permit: it covers one move. Under the WASHTO agreement it is valid for five days. Apply through any member state. Confirm the current member list plus limits with the issuing state before relying on them.
The checks
| Check | Result | Detail |
|---|---|---|
| Width | Over | 12.0 ft wide. The federal width limit is 8 ft 6 in. Over by 3.5 ft. |
| Height | Over | 14.0 ft high. Over the 13 ft 6 in height used as the screening line. Some states allow 14 ft without a permit. Check each state on the route. |
| Overall length | Check | 80.0 ft overall. Over the 75 ft screening line. Overall length limits vary by state. Check each state on the route. |
| Gross weight | Over | 95,000 lb gross. Over the 80,000 lb federal gross limit by 15,000 lb. |
| Load type | Permit | A non-divisible load. OS/OW permits exist for loads that cannot be split without losing their use or value, or that take more than 8 work-hours to dismantle. |
| Superload screen | Routine | Within the routine-permit screening line: 16 ft wide, 16 ft high, 125 ft long, plus 200,000 lb. Each state draws its own superload line. Check the Superload Threshold Checker. |
| Regional permit | Fits | Fits the published WASHTO limits: 14 ft wide, 110 ft long, plus 160,000 lb gross. One regional permit can cover the member states on the route. Confirm the height limit with the issuing state. |
| Trip frequency | Single-trip | 2 trips a year on this lane. A single-trip permit per state is still the simple answer. |
The figures
| Figure | Value | Note |
|---|---|---|
| Width | 12.0 ft | Federal limit 8 ft 6 in. |
| Height | 14.0 ft | Screening line 13 ft 6 in. Some states allow 14 ft. |
| Overall length | 80.0 ft | Screening line 75 ft. State limits vary. |
| Gross weight | 95,000 lb | Federal limit 80,000 lb. |
| Measures over the baseline | 4 | width, height, length, weight. |
| Load type | Non-divisible | Non-divisible loads are the loads OS/OW permits exist for. |
| Trips per year on this lane | 2 | Trip frequency decides between single-trip, time, plus annual permits. |
| Recommended permit family | WASHTO Western Regional Permit | Validity: 5 days. |
| Regional permit fit | WASHTO: fits | Member states: AZ, CO, ID, LA, MT, NV, NM, OK, OR, TX, UT, WA (GAO 2015). |
What to do
- Apply for the regional permit through any member state on the route.
- Confirm the current member list plus limits with the issuing state before the move.
- Confirm the legal limits in every state on the route with the State Legal Limits Table.
- Check the escort, sign, plus curfew rules for the route before the move.
- Carry the permit in the cab for the whole move. A permit covers state roads only: city streets plus county roads need their own approval.
Before you apply
- Measure the load as it will travel, including overhang plus any attachments. Permit limits apply to the whole combination.
- Have the USDOT number ready. Texas checks it against FMCSA records before issuing a permit.
- A permit covers state roads only. City streets plus county roads need their own approval.
- Trip permits for registration plus fuel tax are separate from OS/OW permits. Check the Trip Permit Checker when the unit is not apportioned or licensed for the state.
Notes
- There is no federal oversize permit. FHWA states plainly that the federal government does not issue permits for oversize or overweight vehicles. Each state issues its own.
- Validity varies by state. Washington single-trip permits run 3 days. Texas single-trip permits typically cover 5 days. The permit prints its own effective plus expiration dates: those dates govern.
- Regional agreement membership comes from a GAO survey published in February 2015. Confirm the current member list with the issuing state.
- Superload thresholds vary by state. This tool screens against the Washington line (16 ft, 16 ft, 125 ft, 200,000 lb). The Superload Threshold Checker holds the per-state lines.
- This tool recommends a permit family. It does not issue a permit, set a route, or replace the state permit office.
This tool recommends a permit family from published state plus federal sources. Confirm the result against the permit office in each state on the route before acting. A measurement taken wrong gives a wrong recommendation, so re-measure any figure that sits close to a limit.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool recommends a permit family from published state plus federal sources, not legal advice — confirm the result with the permit office in each state on the route before moving the load.
Quick answer: Which oversize permit you need depends on four facts: the size plus weight of the load, whether it can be split, how often the lane runs, plus how many states the route crosses. A one-time non-divisible move takes a single-trip permit from each state on the route. A lane that runs every week usually pays for an annual or envelope permit. A load past the routine limits needs a superheavy or superload permit. A multi-state move inside the published limits may qualify for one regional permit instead of a permit from each state. There is no federal oversize permit: every permit comes from a state. Answer the six questions above to get the recommendation for your load.
Who issues an oversize permit?
No federal agency issues an oversize permit. The Federal Highway Administration states it plainly on its permit page: the federal government does not issue permits for oversize or overweight vehicles. Issuing permits is a state option. Each state on the route issues its own permit, with its own limits, its own fees, plus its own travel rules. A load crossing five states needs five permits, unless a regional permit covers the member states on the route.
The federal role stops at the baseline. Federal law sets the maximum weights for the Interstate System at 80,000 pounds gross, 20,000 pounds on a single axle, plus 34,000 pounds on a tandem axle group, under 23 CFR 658.17 plus 23 USC 127. Federal law also sets the width limit at 102 inches. Everything past that baseline belongs to the states: the permit, the route, the hours the load may move, the escorts plus signs it needs, plus the conditions printed on the permit itself.
A permit authorizes one vehicle plus load to exceed the legal limits on a set route, at set times, under set conditions. It is not a general license to run heavy. The permit names the origin plus destination, the route, the dates, the dimensions plus weight it covers, plus any escort or travel restriction. A load one inch wider or one pound heavier than the permit allows is running without a permit for that excess.
Apply to the permit office in each state on the route. Most states run an online portal: Texas uses TxPROS, the Texas Permitting and Routing Optimization System, with a Permit Wizard that lists the permit types available for a given load. Washington uses eSNOOPI Pro, where routine permits can be self-issued around the clock. The FHWA keeps a directory of state permit offices plus their contact details for carriers that need to find the right office first.
One more boundary matters before you apply. A state permit covers state roads only. City streets plus county roads need their own approval from the local authority. A permit that routes a load off the state highway onto a county road does not authorize the county miles. Check the local rules for the first plus last miles, where the load leaves the highway system.
What are the types of oversize permits?
States issue the same few permit families under different names. Six families cover nearly every move. The tool above recommends one of them from your answers. The table below sets out each family, what it covers, plus how long it lasts.
| Permit family | What it covers | How long it lasts |
|---|---|---|
| Single-trip | One continuous movement from origin to destination, on a route the state sets | One trip; 3 days in Washington, typically 5 days in Texas |
| 30/60/90-day time permit | Repeated moves of the same type inside a fixed window, usually width or length only | 30, 60, or 90 days from the effective date |
| Annual or envelope | Repeated moves inside a fixed size plus weight envelope, often tied to one vehicle or one company | 1 year |
| Superheavy or superload | Loads past the routine limits, with an engineering review plus route survey | One trip, dates printed on the permit |
| Regional multi-state | One permit covering the member states on a route, inside published size plus weight limits | One trip; 5 days under the WASHTO agreement |
| Divisible or commodity | Divisible loads only where a grandfathered right or a specific authorization exists | Varies with the commodity permit |
The single-trip permit is the default. It fits a one-off move, an unusual load, or a first run on a lane. The time permit fits a season of similar moves. The annual or envelope permit fits a lane that runs every week with loads inside one envelope. The superheavy permit is not a choice: it is what the load requires once it passes the routine limits. The regional permit is a paperwork shortcut for a multi-state move inside the published limits. The divisible permit is the exception that proves the rule: routine permits do not cover loads that can be split.
Specialized permits sit beside these six families. Texas issues separate permits for manufactured housing, portable buildings, house moves, intermodal containers near ports, hay, timber, utility poles, plus well servicing units, most of them valid for one year. Washington issues monthly plus annual permits for single trailers, double trailers, fixed loads, plus manufactured housing. A specialized permit beats a general one when the load fits it: the conditions match the cargo, plus the price is usually lower. Check the state permit page for a specialized permit before applying for a general one.
The families also differ in what they ask of the carrier. A single-trip permit asks for the route plus the dates. An envelope permit asks for the envelope: the maximum width, height, length, plus weight the carrier will move all year. A superheavy permit asks for axle spacings, a route survey, plus time: the review takes days or weeks. The questions in the tool above follow that shape: size plus weight first, then the load type, then the frequency, then the route.
Do I need an oversize permit at all?
Start with the federal baseline. A load needs a permit when it exceeds any one of the legal limits: 8 feet 6 inches wide, 13 feet 6 inches high as the usual screening line, or 80,000 pounds gross on the Interstate. Exceeding one limit is enough. A load 12 feet wide at legal weight needs a permit. A load 80,000 pounds at legal size does not. The Federal Size Limits Checker runs the baseline by vehicle configuration.
Height is the limit that varies most. Many states cap legal height at 13 feet 6 inches. Texas allows 14 feet without a permit. A load 14 feet high needs a height permit in most states plus none in Texas. The tool above screens height at 13 feet 6 inches, then warns that some states allow 14 feet. Check the height limit in each state on the route before deciding: the State Legal Limits Table holds the per-state figures.
Length works differently. Federal law sets no overall length limit for most combinations on the National Network. States cap overall length themselves, commonly between 65 feet plus 75 feet, with longer limits for specific combinations. The tool above screens overall length at 75 feet. A combination under 75 feet can still need a length permit in a state with a lower cap. A combination over 75 feet almost certainly needs one somewhere on the route.
Weight has a second test past the gross figure: the axle weights plus the Bridge Formula. A combination at 80,000 pounds gross can still be overweight on one axle group. The Bridge Formula caps the weight on any group of axles by the distance between them. The Bridge Formula Axle Weight Checker works out the legal maximum for any axle spacing. Check the axle weights before applying: a permit for gross weight does not excuse an axle group that breaks the formula.
Worked example: a load 12 feet wide, 14 feet high, 80 feet long, plus 95,000 pounds gross is over on all four measures. It needs a permit in every state on the route. The width alone triggers the permit. The height triggers it in most states. The length triggers it in states with a lower cap. The weight triggers it everywhere on the Interstate. The tool above scores this load as 4 measures over the baseline, then recommends a permit family from the lane plus the route.
The reverse also matters. A load inside every limit needs no OS/OW permit, whatever the cargo. A legal load is a legal load. The tool above says so plainly when nothing is over, then still points at the State Legal Limits Table, because a state limit off the Interstate can be lower than the federal baseline.
What is a single-trip permit?
A single-trip permit covers one continuous movement from a specific origin to a specific destination, on a route the state sets. It is the permit most heavy-haul moves run on. The load must be non-divisible: the permit exists for loads that cannot be split. The permit names the dates the move may happen, the route it must follow, plus any escort or travel condition. A different route needs a different permit.
Validity varies by state, which catches carriers out. Washington issues a single-trip OS/OW permit valid for 3 days. Texas single-trip permits typically cover a five day window: the TxDOT Motor Carrier Handbook describes a single continuous movement not to exceed five days, plus a verified issued permit shows a five day effective window. The current TxDMV general single-trip page prints no validity period at all, so the five day figure is typical rather than printed. The permit prints its own effective plus expiration dates. Those dates govern, whatever the usual window is.
Texas sets the shape of the general single-trip permit clearly. TxDMV issues it for non-divisible vehicles plus loads exceeding Texas legal size plus weight limits, up to 254,300 pounds. Above that figure, or above 200,000 pounds with less than 95 feet of axle spacing, the load needs a superheavy permit instead. Texas checks the USDOT number against FMCSA records before issuing the permit. A carrier with no USDOT number needs a Permit Surety Bond of 10,000 dollars on file with TxDMV, per the TxDMV general single-trip page read November 19, 2026.
Texas also sets two document thresholds that matter at application time. Above 200,000 pounds gross, a Shipper Certificate of Weight travels with the application. Above 20 feet wide, 18 feet 11 inches high, or 125 feet long, a Route Inspection Certification must be on file before the permit is issued. The tool above flags each of these when the load crosses the threshold. For a Texas-only move, the Texas Permit Wizard answers the same question for Texas alone, with the state permit types plus superheavy rules.
The single-trip permit fits a one-off move, an unusual load, or a first run on a lane. It fits badly when the same move repeats every week: each trip means a new application, a new route, plus a new fee. At that point the time permit or the annual permit takes over. The tool above flips the recommendation at 3 trips a year for a time permit, plus at 12 trips a year for an annual permit.
What is a 30/60/90-day permit?
A time permit covers repeated moves of the same type inside a fixed window, without buying a single-trip permit for every move. Texas issues the clearest version: 30, 60, plus 90 day permits for loads exceeding Texas legal width or length limits. The carrier picks the effective period. The permit expires 30, 60, or 90 days from the effective date, depending on the type purchased.
The Texas time permit has hard size caps. An overwidth permit covers loads no greater than 13 feet wide plus 14 feet high at legal length. An overlength permit covers vehicles plus loads no greater than 8 feet 6 inches wide, 14 feet high, plus 110 feet long on a trailer. A single vehicle moving empty or hauling a load may be no longer than 75 feet. The width plus length permits may be used together. Neither permit is valid for manufactured homes or portable buildings. The permit is issued to the truck or truck-tractor. It may not be amended or transferred between vehicles or permittees.
Washington offers the same idea in monthly plus annual form. Its monthly/annual permits cover a single trailer with a divisible load up to 56 feet, a set of double trailers up to 68 feet, a non-divisible dimensional load up to 14 feet wide, 15 feet high, plus 125 feet long, plus fixed loads such as cranes by the month. The pattern is the same as Texas: a fixed window, a fixed envelope, repeated moves inside it.
A time permit fits a season of similar moves: a construction project that runs three months, a harvest that runs six weeks, a factory contract with a dozen loads in a quarter. It fits badly for a one-off move, where the single-trip permit is cheaper, plus for a year-round lane, where the annual permit is cheaper. The tool above recommends a time permit at 3 to 11 trips a year, then flips to an annual permit at 12 trips.
Check the caps before buying. A time permit that caps width at 13 feet does not cover a 14 foot load. A time permit for length does not cover weight. The Texas time permit is width or length only: an overweight load needs a different permit. Read the permit conditions when they arrive, plus measure every load against the caps, not just the first one.
What is an annual or envelope permit?
An annual or envelope permit covers repeated moves inside a fixed size plus weight envelope for a full year. The carrier states the envelope: the maximum width, height, length, plus weight it will move. Every move inside the envelope is covered. Every move outside it needs a separate permit. The envelope is the whole deal: it trades per-trip paperwork for a hard ceiling on every load.
Texas issues two envelope permits, both valid for one year. The Company Specific Envelope permit can be used to operate any truck owned or leased by the company, one at a time. The Vehicle Specific Envelope permit is tied to one vehicle. Both cover non-divisible loads. Texas also issues an Annual Length Permit for non-divisible overlength loads, valid for one year. The choice between company plus vehicle turns on the fleet: one truck running the same lane takes the vehicle permit, a fleet sharing the lane takes the company permit.
Other states run the same idea under different names. Wisconsin issues annual, consecutive month, plus multiple trip permits under Wis. Stat. s. 348.27, with the standards in Trans 255. Washington issues monthly plus annual permits for the configurations listed above. The names differ. The shape is the same: a fixed window, a fixed envelope, repeated moves.
An annual permit pays when the lane runs all year. At 12 trips a year, the arithmetic usually favors the annual permit over 12 single-trip applications, each with its own route plus fee. At 24 trips a year, the case is strong. At 52 trips a year, the single-trip route is not a serious option: the paperwork alone eats the margin. The tool above recommends an annual permit at 12 trips a year or more.
Price it before buying. The Oversize Cost Calculator works out the single-trip fees by state plus the breakeven point against an annual permit. Run the numbers for the actual lane: the breakeven moves with the states on the route, the weight of the load, plus the number of trips. A lane through two states breaks even sooner than a lane through six.
Envelope discipline is the part carriers get wrong. The envelope binds every move, not just the average one. A load one inch over the envelope width is not covered, even when the last fifty loads fit. Measure every load against the envelope before dispatch. When the loads start pressing against the ceiling, apply for a wider envelope or fall back to single-trip permits for the oversize ones.
What is a superheavy or superload permit?
A superheavy or superload permit covers a load past the routine limits. It is not a bigger version of the single-trip permit. It is a different process: an engineering review of the bridges on the route, a route survey, plus a lead time measured in days or weeks. The state needs to know the load will not damage a bridge or jam under a structure before it issues the permit.
Each state draws its own line. Washington treats a load as a superload past its self-issue limits: over 16 feet wide, over 16 feet high, over 125 feet of trailer load length, or over 200,000 pounds gross. Texas calls the same idea superheavy: over 254,300 pounds gross, over the maximum permit weights on any axle or axle group, or over 200,000 pounds with less than 95 feet of axle spacing. Other states set other lines. The Superload Threshold Checker holds the per-state thresholds, so the line for each state on the route can be checked in one place.
The tool above screens against the Washington line: over 16 feet wide, over 16 feet high, over 125 feet long, or over 200,000 pounds. A load past any one of those four figures gets the superheavy recommendation plus a warning to start early. A load inside all four is routine in Washington, but it can still be a superload in a state with a lower line. The screen is a starting point, not a ruling.
What changes with a superload permit is the timeline plus the paperwork. The application needs axle spacings, often a route survey, plus sometimes a bridge analysis. The state may set a specific route, specific travel hours, escort requirements, plus conditions such as crossing a bridge alone at low speed. Lead times run from days to weeks depending on the state plus the load. Apply as early as the schedule allows: a superload permit applied for the day before the move is a move that does not happen.
Superheavy loads also carry extra document rules in some states. Texas requires a Shipper Certificate of Weight above 200,000 pounds, plus a Route Inspection Certification above 20 feet wide, 18 feet 11 inches high, or 125 feet long. Those documents must be in hand before the permit is issued, not after. The tool above flags each threshold when the load crosses it.
Can one permit cover several states?
Yes, inside a regional permit agreement, when the load fits the published limits. Three agreements cover most of the country, plus one bilateral agreement covers two states. Outside them, each state issues its own permit, one at a time. The agreements do not change the permit: they let one member state issue a permit that the other member states honor for a single trip.
The Western Regional Agreement, run by WASHTO, covers 12 western states. The agreement text, revised July 21, 1995, authorizes each member jurisdiction to issue regional permits for non-reducible vehicles up to 14 feet wide, 110 feet overall length, plus 160,000 pounds gross, with axle limits of 21,500 pounds per axle, 43,000 pounds per tandem, plus 53,000 pounds per tridem. A regional permit under the agreement is valid for five days. The member states, per the GAO survey of February 2015, are Arizona, Colorado, Idaho, Louisiana, Montana, Nevada, New Mexico, Oklahoma, Oregon, Texas, Utah, plus Washington.
The Southern Regional Permit agreement, run by SASHTO, covers 16 southeastern states. Its existence is confirmed by Florida Administrative Code rule 14-26.0043, which incorporates the SASHTO Multi-State Permit Agreement (Rev. 08/03) by reference. The published limits are secondary only: 120,000 pounds gross, 13 feet 6 inches high, 14 feet wide, plus 100 feet long, with axle limits of 12,000 pounds on the steer axle, 20,000 pounds on a single axle, 40,000 pounds on a tandem, plus 60,000 pounds for axle groups of three or more. Confirm the limits with the issuing state before relying on them. The member states, per the same GAO survey, are Alabama, Arkansas, Florida, Georgia, Kentucky, Louisiana, Mississippi, Missouri, North Carolina, Ohio, Oklahoma, South Carolina, Tennessee, Texas, Virginia, plus West Virginia.
The New England Transportation Consortium covers the northeast. The GAO table lists only Maine plus New Hampshire as members. A secondary compilation lists all five New England states: Maine, Massachusetts, New Hampshire, Rhode Island, plus Vermont. The tool above follows the GAO table, since it is the dated government source, plus notes the wider claim here. The published NETC limits are secondary only: 108,000 pounds on five axles, 120,000 pounds on six or more axles, 13 feet 6 inches high, 14 feet wide, plus 90 feet long. Minnesota plus Wisconsin run a bilateral agreement between the two states.
| Agreement | Member states (GAO, Feb 2015) | Published limits |
|---|---|---|
| WASHTO Western Regional | AZ, CO, ID, LA, MT, NV, NM, OK, OR, TX, UT, WA | 14 ft wide, 110 ft long, 160,000 lb gross, valid 5 days |
| SASHTO Southern Regional | AL, AR, FL, GA, KY, LA, MS, MO, NC, OH, OK, SC, TN, TX, VA, WV | 14 ft wide, 13 ft 6 in high, 100 ft long, 120,000 lb gross |
| NETC New England | ME, NH (GAO table) | 14 ft wide, 13 ft 6 in high, 90 ft long, 108,000 lb gross |
| MN-WI bilateral | MN, WI | Per the bilateral agreement |
Twenty-two states plus the District of Columbia sit outside every agreement, per the same GAO table: Alaska, California, Connecticut, Delaware, Hawaii, Illinois, Indiana, Iowa, Kansas, Maryland, Massachusetts, Michigan, Nebraska, New Jersey, New York, North Dakota, Pennsylvania, Rhode Island, South Dakota, Vermont, plus Wyoming. A route through any of them needs a separate permit from that state, whatever the regional permit covers. California, New York, plus Wyoming are the notable gaps for long-haul routes.
Three cautions apply to every regional permit. First, the membership list comes from a GAO survey published in February 2015. States join plus leave agreements. Confirm the current member list with the issuing state. Second, the SASHTO plus NETC limits come from published secondary compilations, not from the agreement texts. The WASHTO limits come from the agreement text itself. Third, a regional permit is still a single-trip permit: it covers one move, not a season. A lane that runs every week needs an annual permit in each state, not a regional permit for every trip.
What if my load can be split?
A load that can be split is a divisible load, plus routine OS/OW permits do not cover it. The rule comes from 23 CFR 658.5, which defines a nondivisible load or vehicle as one exceeding the length or weight limits which, if separated into smaller loads or vehicles, would compromise its intended use, destroy its value, or require more than 8 work-hours to dismantle using appropriate equipment. The applicant for a nondivisible load permit bears the burden of proof on the number of work-hours required to dismantle the load.
Work through the three parts in order. First, would splitting the load make it unable to perform the function it was built for? A transformer split in half is not a transformer. Second, would splitting it destroy its value? A prefabricated bridge section cut apart is scrap. Third, would dismantling it take more than 8 work-hours with the right equipment? A machine that unbolts in two hours fails this part. Any one part satisfied makes the load non-divisible. None satisfied makes it divisible.
Divisible loads can still be permitted, but only through narrow doors. FHWA states that divisible load permits rest on historic state grandfather rights or specific congressional authorization for a commodity or route. Texas runs one such door: the Over Axle/Over Gross Weight Tolerance permit, valid for one year, for divisible commodities on state-maintained plus county roads in select counties. Texas also runs annual permits for timber, plus a fluid milk permit: fluid milk products cannot be easily dismantled or divided under 23 USC 127(a)(13). The emergency door is 23 USC 127(i): divisible-load permits for relief supplies only, for 120 days after a Stafford Act disaster declaration. Texas mirrors it with a Federal Disaster Relief Permit that expires 120 days from the declaration date.
The practical answer for most divisible loads is simple: split the load to legal weight. Two legal loads beat one permit that does not exist. Where a commodity permit covers the cargo, apply for that permit by name, not for a general OS/OW permit. A general OS/OW application for a divisible load will be refused, plus the refusal costs the time the split would have taken.
States may also treat three specific things as non-divisible by law: emergency response vehicles, including those loaded with salt, sand, chemicals, or a combination of them, while spreading material on slick or icy highways; casks designed for the transport of spent nuclear materials; plus military vehicles transporting marked military equipment or materiel. Those are the only standing exceptions in the federal definition. Everything else must pass the three-part test.
Should I buy single-trip permits or an annual permit?
Trip frequency decides. One trip a year on a lane takes a single-trip permit per state. Two trips a year still take single-trips: the annual permit costs more than two applications. Three to eleven trips a year sit in the middle, where a 30/60/90-day time permit or an annual permit is worth pricing. Twelve trips a year or more usually favor the annual or envelope permit. The tool above draws the lines at 3 plus 12 trips.
The fee maths decides the close cases. A single-trip permit fee is small in most states. An annual permit fee is larger. The breakeven point is the number of single-trips whose fees equal the annual fee. The Oversize Cost Calculator works out the single-trip fees by state plus the breakeven point for the actual lane. Run it before buying: the breakeven moves with the states on the route plus the weight of the load.
Paperwork costs count beside the fees. Each single-trip permit is a separate application, a separate route, plus a separate set of conditions to read. Ten single-trips mean ten applications, ten routes to check, plus ten permits to carry. An annual permit means one application plus one envelope to respect. A dispatcher running a weekly lane saves hours a month on the annual permit, even when the fees alone look close.
Three facts push the answer toward the annual permit: the same lane every week, loads inside one envelope, plus a fleet that shares the lane. Three facts push it back toward single-trips: a lane that runs once, loads that vary widely in size, plus a route that changes every trip. A carrier running the same 12 foot wide transformer down the same highway every Monday is the annual permit customer. A carrier moving a different machine to a different site each month is the single-trip customer.
Do not buy the annual permit for the wrong reason. An annual permit does not cover a load outside its envelope. It does not cover a state it was not issued for. It does not waive the escort, sign, or curfew rules. It saves paperwork plus fees on repeated moves inside its terms. Nothing more.
What else do I need besides the permit?
A permit is the authorization to move. It is not the whole move. Four more things ride with every oversize load: escorts, signs plus flags, travel windows, plus registration plus fuel tax coverage. Each comes from a different rule, plus each can stop the load on its own.
Escort or pilot car requirements turn on the size of the load plus the state. Wide loads need one escort in some states plus two in others. Long loads need a rear escort. High loads need a pole car to check clearances ahead. The Escort and Pilot Car Checker works out the escort requirement by state plus load size. Book the escorts when the permit is applied for, not after it arrives: escort availability can set the move date.
Signs, flags, plus lights mark the load for other traffic. An oversize load carries OVERSIZE LOAD signs front plus rear, flags on the widest points, plus lights for night movement where night movement is allowed. The rules vary by state: flag size, sign size, plus lamp colors all differ. The Oversize Sign and Flag Checker lists the requirements by state. Check the permit conditions too: a permit can add a sign or a flag past the state minimum.
Travel windows limit when the load may move. Most states ban oversize movement at night, on weekends, plus on holidays, with exceptions by size plus route. Some states ban movement during rush hours near cities. Some ban Sunday movement outright. The Oversize Curfew and Holiday Checker lists the curfew plus holiday rules by state. Plan the move around the windows: a permit valid for five days with a weekend ban inside it gives three moving days, not five.
Registration plus fuel tax coverage is separate from the OS/OW permit. A truck not apportioned under IRP for a state, or not licensed under IFTA for fuel tax there, needs a trip permit for that state. The Trip Permit Checker works out which trip permits the move needs. Do not confuse the two kinds of trip permit: the OS/OW single-trip permit covers size plus weight, while the IRP trip permit covers registration plus the IFTA permit covers fuel tax. A move can need all three.
Finally, check the route itself. A permit routes the load, but the driver still owns the clearances: low bridges, tight turns, plus weight-restricted structures on the last miles. Texas requires a Route Inspection Certification above 20 feet wide, 18 feet 11 inches high, or 125 feet long, precisely because the last miles hold the surprises. Drive the route on a map before the move, plus check the structures the permit names.
How do you use the Permit Type Finder?
Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the recommendation change.
- Measure the load as it will travel, including overhang plus attachments.
- Enter the width, height, overall length, plus gross weight.
- Say whether the load is non-divisible, divisible, or you are not sure.
- Enter how many trips a year the lane runs, plus the route region.
- Read the recommended permit family plus the validity.
- Apply through the state portal, or through any member state for a regional permit.
Use measurements from the load, not from a shipping document. A bill of lading gives the cargo dimensions, which may differ from the load as it sits on the trailer, with dunnage, tarps, plus overhang. The permit covers the combination as it travels. Measure the combination.
Read the checks table before the action list. It shows which measures are over, whether the load screens as a superload, whether a regional permit fits, plus what the trip frequency points to. The recommendation follows from those checks. When the recommendation surprises you, the checks table shows why.
Questions drivers ask
Which oversize permit do I need for a one-time move?
A single-trip permit from each state on the route. Each state issues its own permit for one continuous movement from origin to destination, on a route the state sets. The load must be non-divisible. Validity varies by state: 3 days in Washington, typically 5 days in Texas. The permit prints its own effective plus expiration dates. Those dates govern.
How long is a single-trip oversize permit valid?
It varies by state. Washington issues a single-trip OS/OW permit valid for 3 days. Texas single-trip permits typically cover a five day window, per the TxDOT Motor Carrier Handbook plus a verified issued permit. Other states set their own windows. Every permit prints its own effective plus expiration dates. Those dates are the answer for that permit.
What is an envelope permit?
An annual permit that covers repeated moves inside a fixed size plus weight envelope. Texas issues two kinds, both valid for one year: a Company Specific Envelope permit, usable on any truck the company owns or leases, one at a time, plus a Vehicle Specific Envelope permit tied to one vehicle. Every move inside the envelope is covered. A move outside the envelope needs a separate permit.
Can one permit cover several states?
Yes, inside a regional permit agreement, when the load fits the published limits. The WASHTO Western Regional Agreement covers 12 western states up to 14 feet wide, 110 feet long, plus 160,000 pounds gross, valid for five days. The SASHTO agreement covers 16 southeastern states. The NETC agreement covers Maine plus New Hampshire. Outside the agreements, each state issues its own permit.
Can I get a permit for a divisible load?
Generally no. Routine OS/OW permits cover non-divisible loads only. A divisible load can be permitted only under a grandfathered right or a specific congressional authorization for a commodity or route, such as the Texas Over Axle/Over Gross Weight Tolerance permit for divisible commodities. The emergency exception in 23 USC 127(i) covers relief supplies only, for 120 days after a disaster declaration. Most divisible loads should be split to legal weight.
What makes a load a superload?
Each state draws its own line. Washington treats a load as a superload past 16 feet wide, 16 feet high, 125 feet of trailer load length, or 200,000 pounds gross. Texas calls it superheavy past 254,300 pounds gross, or past 200,000 pounds with less than 95 feet of axle spacing. A superload permit means an engineering review, a route survey, plus a lead time measured in days or weeks. Check the Superload Threshold Checker for the line in each state on the route.
Related tools
- Superload Threshold Checker: find where each state on the route draws the superload line.
- Trip Permit Checker: work out which IRP plus IFTA trip permits the move needs.
- Oversize Cost Calculator: price single-trip fees by state plus the breakeven point against an annual permit.
- State Legal Limits Table: check the legal size plus weight limits in every state on the route.
Sources
- FHWA, Oversize/Overweight Load Permits (the federal government does not issue permits; divisible-load permits rest on grandfather rights or congressional authorization)
- 23 CFR 658.5, Definitions (eCFR, read verbatim Nov 19, 2026; nondivisible load definition)
- 23 CFR 658.17, Weight (eCFR; 80,000 pound gross limit on the Interstate)
- 23 USC 127, Vehicle weight limitations (Cornell LII; 80,000 pound cap, emergency divisible-load permits)
- TxDMV, Oversize/Overweight Permits (permit options plus 30/60/90-day, envelope, plus superheavy permits; read Nov 19, 2026)
- WSDOT, Permit types and fees (single-trip 3-day permit, self-issue limits, monthly plus annual permits; read Nov 19, 2026)
- WASHTO, Western Regional Agreement (revised July 21, 1995; regional permit limits plus five day validity)
- GAO-15-235SP, Regional Permit Agreement Membership (February 2015; state-by-state membership table)