Skip to main content

Trucking Mind

The table minimum, not a guess. Every truck tire size carries a published load-inflation table. Find the row for your load, read the pressure. That pressure is the minimum cold PSI for the tire. This calculator runs that lookup for the five most common semi truck sizes, then checks your current pressure against the answer.

Enter the load you know. Every answer updates the result as you change each field.

Your tire

Your load

2 tires on this axle. The axle weight is divided by 2 to get the load per tire.

A little low: 85 PSI is 5 PSI under the 90 PSI minimum for this load.

11R22.5, load range G, steer axle, single tires: recommended 90 PSI cold, current 85 PSI.

A load of 5,500 lb per tire needs at least 90 PSI in this size and load range. The tire is at 85 PSI, 5 PSI short, which is 5.6 percent under the minimum.

The checks

CheckResultDetail
Load on the tireWithin capacity5,500 lb per tire needs at least 90 PSI in this size and load range.
Current cold pressure5 PSI low85 PSI against a 90 PSI minimum, 5.6 percent under.
Load range limitWithin the rangeLoad range G tops at 105 PSI and 6,175 lb per tire in this size.

The figures

FigureValueNote
Load per tire5,500 lbEntered directly as the load on one tire.
Tires on this axle2Steer axle, single tires.
Axle load11,000 lbLoad per tire times the tires on the axle.
Recommended cold pressure90 PSILowest table pressure that carries the load.
Capacity at 90 PSI5,510 lb per tireMaximum load the table allows at this pressure.
Load margin10 lbCapacity minus load.
Capacity used99.8%Share of the table capacity this load takes up.
Current cold pressure85 PSIAs entered. Check it cold, before driving.
Shortfall5 PSI (5.6 percent)Gap between the current pressure and the table minimum.
Maximum for this tire6,175 lb at 105 PSILoad range G maximum for 11R22.5, single fitment.

What to do

  • Add 5 PSI to reach 90 PSI cold.
  • Check the valve stem and the bead for a slow leak if the same tire keeps dropping.

Notes

  • Table pressures are minimum cold pressures for the load. Cold means the tire has not run for at least three hours.
  • Weigh each axle end separately and set the whole axle to the pressure the heavier end needs. Pressures must be equal across an axle.
  • Goodyear recommends adding 10 PSI above the table minimum to cover pressure loss between checks, never above the wheel maximum.
  • Many fleets run steer tires at the sidewall maximum pressure for handling and even wear, above the table minimum. The table value is the lowest safe pressure, not the fleet setting.

This calculator applies the published load-inflation tables for your size, load range and fitment. Confirm the result against the table for the exact tire on your truck before you rely on it.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is provided for general information only. It is not legal advice — check the load-inflation table for the exact tire fitted to your truck before you rely on a result.

Quick answer: There is no single correct PSI for a semi truck tire. The right pressure comes from the load-inflation table for the tire size, the load on each tire, plus whether the tire runs single or dual. A common steer tire, 11R22.5 in load range G, needs 90 PSI at 5,500 lb per tire and 105 PSI at 6,175 lb. The same load on a drive axle in dual fitment needs more pressure, because each tire in a dual pair carries less than a single tire. Table pressures are minimum cold pressures. Check the pressure cold, before driving, with a calibrated gauge.

Last reviewed: · Focus keyword: semi truck tire pressure chart

What PSI should semi truck tires run at?

There is no one number. The right pressure depends on the tire size, the load on each tire, the load range plus whether the tire runs single or dual. The published load-inflation tables run from 70 PSI to 120 PSI across the five common sizes in this calculator. The answer for a loaded truck usually lands between 85 PSI and 110 PSI.

A loaded steer axle of 12,000 lb puts 6,000 lb on each steer tire. An 11R22.5 tire in load range G needs 105 PSI for that load. A loaded tandem group of 34,000 lb puts 4,250 lb on each of its eight tires. A 295/75R22.5 tire in dual fitment needs 75 PSI for that load. Same truck, same trip, very different pressures, because the load per tire decides the answer.

The table value is a minimum, not a target. It is the lowest cold pressure that carries the load. Running below it flexes the sidewall more than the tire was built to flex. The extra flex turns into heat. Running above it is safe for the load but wears the center of the tread and rides harder. The sidewall maximum is a limit, not a setting. The table row for your load is the setting.

The table below shows the recommended pressure at 5,500 lb per tire for every size plus load range in this calculator. For any other load, run the calculator above.

Tire sizeLoad rangeSingleDual
11R22.5G90 PSI100 PSI
11R22.5H90 PSI100 PSI
295/75R22.5G95 PSI110 PSI
295/75R22.5H95 PSI110 PSI
285/75R24.5G95 PSI110 PSI
285/75R24.5H95 PSI110 PSI
11R24.5G85 PSI90 PSI
11R24.5H85 PSI90 PSI
275/80R22.5G95 PSI110 PSI
275/80R22.5H90 PSI100 PSI

Recommended cold pressure at 5,500 lb per tire, from the published load-inflation tables. Load range H uses the same table as G for most sizes, except 275/80R22.5, which has separate G and H tables.

How do load-inflation tables work?

Every truck tire size has a published load-inflation table. Tire makers build the tables from standards set by the Tire and Rim Association. The tables agree across makers for the standard sizes. Each row pairs one cold pressure with the maximum load the tire can carry at that pressure, listed separately for single fitment plus dual fitment.

Read the table from the load, not from the pressure. Find the first row where the capacity covers the load on the tire, then read the pressure in that row. If the load falls between two rows, use the higher row. Never round down. A tire at 5,510 lb per tire needs the 90 PSI row in 11R22.5 load range G, because the 85 PSI row carries only 5,220 lb.

The dual column always sits lower than the single column. Two tires side by side share the load, but each one carries less than a single tire would, because heat builds up between the pair and the inner tire runs hotter. Never use the single column for a dual tire. On an 11R22.5 at 100 PSI, a single tire carries 5,950 lb while each tire in a dual pair carries 5,625 lb.

The load range caps the table. A load range G tire must not use a row above the G maximum pressure for its size, even when the table prints higher rows. Those rows belong to load range H tires. In 11R22.5 plus 11R24.5, G stops at 105 PSI. In 295/75R22.5, 285/75R24.5 plus 275/80R22.5, G stops at 110 PSI.

One size breaks the pattern. The 275/80R22.5 has two separate tables, one for load range G plus one for load range H, with different values at every pressure. An 11R22.5 uses one table for both ranges. This calculator stores the separate 275/80R22.5 tables, so the answer follows the right one.

A few models carry their own higher tables. The Bridgestone R283 in 295/75R22.5, load range H, is rated to 7,160 lb per tire at 120 PSI as a single, against 6,610 lb in the standard table. If the load index on the sidewall does not match the standard table, follow the maker table for that model.

What is the correct tire pressure for 11R22.5 tires?

11R22.5 is the most common semi truck tire size in North America. It is the size this calculator opens with. The table below gives the recommended pressure at five typical loads, in single plus dual fitment, for load range G.

Load per tireSingleDual
4,500 lb70 PSI75 PSI
5,000 lb85 PSI90 PSI
5,500 lb90 PSI100 PSI
6,000 lb105 PSI120 PSI (H only)
6,175 lb105 PSIOver the limit

11R22.5 load range G. At 6,000 lb per tire in dual fitment, load range G tops at 5,840 lb, so the tire must be load range H at 120 PSI. At 6,175 lb per tire in dual fitment, no 11R22.5 tire can carry the load.

On a steer axle, 11R22.5 load range G tires run at 90 to 105 PSI at the usual steer loads of 5,500 to 6,175 lb per tire. On a drive axle in dual fitment, the same tire often runs at 75 to 100 PSI, because each tire in a dual pair carries less. A drive tire carrying 6,000 lb per tire in dual fitment needs load range H, because the G dual maximum is 5,840 lb.

The G ceiling matters. A load range G tire in 11R22.5 tops at 105 PSI plus 6,175 lb per tire as a single. If the load needs more, the answer is a load range H tire, not more air in a G tire. Over-inflating past the sidewall maximum can damage the tire plus the wheel.

If the truck runs 11R22.5 on every axle, the steer tires need the highest pressure, because they carry the most load per tire. Set each axle to the pressure its own load needs. Keep the pressure equal across each axle.

How much pressure do steer tires need?

Steer tires carry the heaviest load per tire on the truck. A typical loaded steer axle weighs 11,000 to 12,000 lb, which puts 5,500 to 6,000 lb on each of the two tires. At 5,500 lb, an 11R22.5 load range G tire needs 90 PSI. At 6,000 lb, it needs 105 PSI. The jump is steep because the table rows near the top of the range add less capacity per PSI.

Steer tires matter more than any other tire on the truck. A steer tire failure takes away steering control at highway speed. A blowout on the steer axle is the most dangerous tire failure a driver can face. That is why steer tires get the closest attention at inspection. The pressure check on the steer axle comes first in a pre-trip walkaround.

Many fleets run steer tires at the sidewall maximum pressure, above the table minimum, for handling plus even wear. That is a fleet choice, not a table requirement. The table value is the lowest safe pressure for the load. This calculator gives the table value. If the fleet runs a higher steer pressure as a matter of policy, follow the fleet policy. Treat the table value as the floor below which the tire must never drop.

The steer axle weight decides the pressure, so the steer axle weight is worth knowing exactly. A scale ticket gives it. The federal bridge formula caps a single axle at 20,000 lb, but the tire ratings cap a steer axle far lower, usually near 12,000 to 13,000 lb. Check the axle against the bridge formula before a heavy load.

How much pressure do drive and trailer tires need?

Drive plus trailer tires run in dual pairs on most trucks, so each tire carries about half the load of a single tire on the same axle weight. A loaded tandem group of 34,000 lb spreads across eight tires, which puts 4,250 lb on each tire. At that load, a 295/75R22.5 in dual fitment needs 75 PSI. An 11R22.5 in dual fitment needs 70 PSI.

Trailer axles often run lighter than drive axles, because the load sits forward of the trailer tandems on many loads. A trailer tandem at 30,000 lb puts 3,750 lb on each tire, which sits below the lightest row in the table for most sizes. The answer is then the lowest table pressure, 70 PSI for most sizes, 75 PSI for 285/75R24.5 plus the 275/80R22.5 load range H table.

The rule that matters most on duals is equal pressure across the axle. In a dual pair, the two tires share one load. If one tire runs low, its mate carries more than its share. The low tire flexes more than it should. Mismatched pressure in a dual pair wears both tires faster. It can overload the good tire past its table limit. Check both tires in every pair. Set both to the same pressure.

Wide-base singles change the math. A wide-base single drive tire replaces a dual pair, so it carries the full axle-end load on one tire. The load per tire doubles. The pressure follows the single column. The calculator has a wide-base single fitment for drive axles, so the answer uses the right column. Axle weight limits vary by state, so check the state legal limits table for the route ahead. Use the axle weight rebalance calculator to shift a heavy axle before it costs a ticket.

What happens if semi truck tires are under-inflated?

An under-inflated tire flexes more with every revolution. The extra flex turns into heat in the sidewall plus the shoulder. Heat is what kills tires. A tire running 20 percent under its recommended pressure can run hot enough to separate the tread from the casing. The failure often comes without warning at highway speed.

The industry line is 80 percent. Tire industry guidance quoted in the Michelin data book says a tire run below 80 percent of its normal recommended pressure can have permanent structural damage to the steel cords. It must be inspected by trained personnel in a safety cage before it is re-inflated. A tire that looks fine after running low can fail on the next trip. This calculator flags any pressure below 80 percent of the recommended value as severe.

The damage builds in stages. Below the table minimum, the shoulders wear faster than the center, because the tread face cups inward. Fuel use rises, because rolling resistance climbs with every PSI below the right pressure. The casing weakens with each hot mile, which shortens the life of the tire plus the value of the casing for retreading.

How far underWhat the tool saysWhat it means
Less than 10 percent underMildUnder-inflated. Top up at the next stop.
10 to 20 percent underModerateHeat plus wear rise fast. Correct it the same day.
More than 20 percent underSevereBelow 80 percent of the recommended pressure. The tire can have permanent cord damage. Have it inspected in a safety cage before re-inflation.

Under-inflation also costs money in ways that show up late. A tire that wears out early costs a replacement plus a roadside call. A casing damaged by heat cannot be retreaded, which throws away the retread value. Fleets that check pressure weekly spend less on tires than fleets that check only when a tire looks low, because a radial tire can be well under pressure before it looks flat. The regulatory side is separate: a flat tire is an out-of-service violation under 49 CFR 393.75, which the Tire Compliance Checker covers. For the money side, the maintenance reserve calculator budgets for tire replacement plus retreads.

How do you check tire pressure the right way?

Check the pressure cold, before the truck moves. Cold means the tire has not run for at least three hours. A tire that has run even a few miles reads higher than its cold pressure, because driving heats the air inside. Never let air out of a hot tire to reach the table value. The table values are cold pressures.

Use a calibrated gauge, not a thump. A thump with a bat or a hammer cannot tell 90 PSI from 100 PSI. It cannot tell a tire at 80 percent from a tire at full pressure. A dial gauge or a digital gauge reads to within 1 or 2 PSI when it is calibrated. It costs less than one tire. Keep the gauge in the cab, not in a toolbox that bakes in the sun.

Check every tire, including the inside duals. The inside dual is the tire most often skipped. It is the tire most likely to run low unnoticed, because it sits out of sight behind its mate. A valve extension or a crossfire equalizer makes the inside dual reachable without crawling under the trailer.

Check weekly, plus before every long trip. A tire loses 1 to 2 PSI a month through the rubber alone. A slow leak can drop a tire 10 PSI in a week. A tire pressure monitoring system catches a leak between checks. It warns the driver while driving, but it does not replace a gauge. A TPMS sensor reads pressure at the valve. A gauge check confirms the reading plus the condition of the valve. A TPMS kit plus a portable tire inflator belong in every new driver starter kit. Both are priced in the new trucker gear cost estimator.

Keep the valve caps on. A missing cap lets dirt plus moisture into the valve core, which causes slow leaks. Replace a cap the same day it goes missing. Build the pressure check into the pre-trip inspection checklist so it happens every day, not only when a tire looks low.

Does tire pressure change with temperature?

Yes. Tire pressure moves about 1 PSI for every 10 degrees F of temperature change. A tire set to 100 PSI on a 70 degree afternoon reads about 97 PSI on a 40 degree morning. It reads about 103 PSI on a 100 degree afternoon. The air inside follows the temperature. Nothing about the tire changes.

That is why the cold check matters. The season matters too. A truck set up in summer runs low in winter if nobody tops up the tires. A truck that crosses from a warm valley into a cold mountain pass loses pressure on the way. Check the pressure at the temperature the truck will run in. Set the pressure cold at that temperature.

The Michelin data book prints a cold-climate correction table for exactly this reason. When the shop is warm and the road is cold, set the pressure higher in the shop so the tire reads right at road temperature. The correction runs about 1 PSI for every 10 degrees F of difference between the shop plus the road.

Altitude has a small effect too. A gauge reads relative to the air around it, so a tire checked at high altitude reads slightly higher than the same tire at sea level. The difference is small at trucking altitudes. The temperature effect matters far more.

How do you find the load on each tire?

The only exact way is a scale. A truck scale ticket gives the weight on each axle group. Divide the axle weight by the number of tires on the axle to get the load per tire. A steer axle at 11,600 lb across two tires puts 5,800 lb on each tire. A drive tandem at 33,200 lb across eight tires puts 4,150 lb on each tire.

Weigh each axle end separately when you can. A load rarely sits evenly across an axle. The heavy end decides the pressure for the whole axle. Set both tires on the axle to the pressure the heavy end needs. Keep the pressure equal across the axle. A tire on the light end running the heavy-end pressure is safe. A tire on the heavy end running the light-end pressure is overloaded.

If there is no scale ticket, work from the load. The bill of lading gives the cargo weight. Add the tractor plus trailer empty weight, then split the total across the axles by the loading pattern. This is an estimate. It runs low when the load sits forward or back. Use the estimate only until a scale ticket is available. Add a margin for the unknown.

The federal limits give a ceiling, not a load. A single axle is capped at 20,000 lb under federal bridge law. A tandem group is capped at 34,000 lb. A loaded truck rarely sits at the ceiling on every axle. The real load per tire comes from the scale, not from the limit. When the scale shows an axle over its limit, the axle weight rebalance calculator shows how far to move the load. The bridge formula checker confirms the legal axle weights for the axle spacing.

What do load range G and H mean?

Load range is the modern form of ply rating. It tells how much load the tire can carry at its maximum pressure. Load range G equals a 14 ply rating. Load range H equals a 16 ply rating. The letter sits on the sidewall, next to the size. It is the second thing to read after the size itself.

The maximum pressure differs by size, so the letter alone does not give the number. In 11R22.5 plus 11R24.5, load range G tops at 105 PSI. In 295/75R22.5, 285/75R24.5 plus 275/80R22.5, load range G tops at 110 PSI. Load range H tops at 120 PSI in all five sizes in this calculator.

Tire sizeG max PSIG max load single / dualH max PSIH max load single / dual
11R22.51056,175 lb / 5,840 lb1206,610 lb / 6,005 lb
295/75R22.51106,175 lb / 5,675 lb1206,610 lb / 6,005 lb
285/75R24.51106,175 lb / 5,675 lb1206,780 lb / 6,175 lb
11R24.51056,610 lb / 6,005 lb1207,160 lb / 6,610 lb
275/80R22.51106,175 lb / 5,675 lb1207,160 lb / 6,610 lb

A higher load range is not a better tire. It is a stronger tire, built for a heavier load at a higher pressure. A truck that runs light does not need load range H tires. Fitting them adds cost plus weight for no benefit. A truck that runs at the G ceiling on every trip needs the H tire, because the G tire has no margin left.

The load index on the sidewall gives the same information in numbers. A 149/146 load index means 7,160 lb as a single tire plus 6,610 lb in dual fitment at the rated pressure. The load index plus the load range must agree. If they do not, follow the load index. Check the maker table for the model.

How do you use the Semi Truck Tire Pressure Calculator?

  1. Read the tire size from the sidewall, then pick it in the size field.
  2. Read the load range from the sidewall, then pick G or H.
  3. Pick the axle position and fitment: steer, drive dual, drive wide-base single, trailer dual or trailer single.
  4. Enter the load per tire in pounds, or enter the axle weight and let the calculator divide it by the tires on the axle.
  5. Enter the current cold pressure if you know it, or leave it blank for the recommended pressure only.
  6. Read the recommended cold pressure, the checks, the figures plus the actions, then set the tire pressure cold before the next trip.

Frequently asked questions

What PSI should semi truck tires be?

There is no single number. The right pressure comes from the load-inflation table for the tire size, the load on each tire plus whether the tire runs single or dual. A common steer tire, 11R22.5 in load range G, needs 90 PSI at 5,500 lb per tire and 105 PSI at 6,175 lb. Run the calculator above for the exact pressure for your load.

What is the correct tire pressure for 11R22.5 tires?

It depends on the load per tire. In load range G, a single 11R22.5 needs 70 PSI at 4,500 lb, 85 PSI at 5,000 lb, 90 PSI at 5,500 lb plus 105 PSI at 6,000 lb. In dual fitment the same loads need 75, 90, 100 PSI plus load range H at 6,000 lb, because the G dual maximum is 5,840 lb.

How do I know the load on each tire?

Weigh the axle on a truck scale, then divide the axle weight by the number of tires on the axle. A steer axle at 11,600 lb across two tires puts 5,800 lb on each tire. Weigh each axle end separately when you can. Set the whole axle to the pressure the heavy end needs.

Is 100 PSI enough for semi truck tires?

It depends on the load. At 100 PSI, an 11R22.5 in load range G carries 5,950 lb as a single tire plus 5,625 lb in dual fitment. If the load per tire is under those numbers, 100 PSI covers it. If the load is higher, the tire needs more pressure, up to the load range maximum of 105 PSI for G or 120 PSI for H.

What happens if truck tires are 20 PSI under-inflated?

A tire 20 PSI under its recommended pressure runs hot, wears the shoulders, uses more fuel plus risks a blowout. If 20 PSI under puts the tire below 80 percent of the recommended pressure, the steel cords can have permanent damage. The tire must be inspected in a safety cage before re-inflation. Check the pressure cold with a gauge. Top it up before driving.

Should steer tires run at a higher pressure than drive tires?

Usually yes, because steer tires carry more load per tire. A loaded steer axle puts 5,500 to 6,000 lb on each tire, while a loaded drive tandem puts about 4,250 lb on each tire. The table gives the steer tire 90 to 105 PSI in 11R22.5 load range G, against 70 to 75 PSI for the drive tires at the lighter load. Many fleets run steer tires at the sidewall maximum for handling plus even wear.

Related tools

Sources

Follow on WhatsApp Ask by Voice