A cracked windshield is a violation, not an out of service condition. This checker tests windshield damage, tint, mounted devices, decals, side windows, wipers and washer against 49 CFR 393.60, 393.61 and 393.78, plus Appendix G items 12 and 13. Windshield glass is never out of service. Only the driver side wiper is, in wet weather.
Describe the windshield and the glass, then enter the measurements. Every answer updates the result as you change each field.
Windshield damage
The protected area runs upward from the top of the steering wheel, excluding a 2 inch border at the top and 1 inch borders at each side. Measure the crack width at its widest point and the damaged area across its widest point.
Tint
Section 393.60(d) requires at least 70 percent transmittance on the windshield and the windows beside the driver. Measure the installed glass with a tint meter. The film rating alone is not the number.
Mounted device
Safety technology may mount within 8.5 inches below the upper edge of the swept area or within 7 inches above its lower edge. Antennas may mount no more than 6 inches below the upper edge of the windshield, outside the swept area. Every device must stay outside the sight lines.
Decal or sticker
Side windows
Wipers, washer, weather
A dead driver side wiper is an out of service item in wet weather. A dead passenger side wiper is a violation only. Any dead wiper fails the annual inspection.
Compliant. The windshield and glass pass the federal rules checked here.
All checks pass.
The windshield damage, tint, mounted device, decal, side windows, wipers and washer all meet 49 CFR 393.60, 393.61 and 393.78, plus Appendix G items 12 and 13. Re-check after any new chip or crack.
The checks
| Check | Result | Detail |
|---|---|---|
| Windshield damage | Pass | A crack not intersected by any other crack is excepted under section 393.60(c)(2). It is legal at roadside whatever its length. |
| Annual inspection crack width | Pass | The crack is 0.125 inches wide, within the 1/4 inch limit Appendix G item 12(2) sets for the annual inspection. |
| Tint | Pass | No tinting entered. |
| Mounted device | Pass | Vehicle safety technology may mount within 8.5 inches below the upper edge of the swept area or within 7 inches above its lower edge, outside the sight lines. This device complies with section 393.60(e)(1)(ii). |
| Windshield decal | Pass | No windshield decal entered. |
| Side windows | Pass | At least one window on each side of the driver compartment, each at least 200 square inches. Section 393.61 is met. |
| Windshield wipers | Pass | Both wipers work. Appendix G item 13 fails any power unit with an inoperative wiper. |
| Windshield washer | Pass | The windshield washing system works, as section 393.78(a) requires for vehicles built on or after December 25, 1968. |
| Out of service risk | Pass | No out of service item here. Windshield glass is never out of service: no CVSA Part II item covers it. A cracked windshield is a section 393.60 violation only. |
What to do
- No repair needed. Keep this result with the vehicle records.
- Re-check the windshield after any new chip or crack, plus before each annual inspection.
Notes
- Windshield glass is never out of service. No CVSA Part II item covers glazing. A cracked windshield is a section 393.60 violation only.
- State law can be stricter than the federal rule. Some states fail any crack in the wiper swept area at the state inspection, whatever section 393.60 allows.
- The annual inspection applies Appendix G item 12, which is stricter than section 393.60 on crack width: 1/4 inch maximum for a crack that is not intersected.
- A driver who finds a defect must report it on the DVIR under section 396.13. The carrier must repair it before the vehicle is dispatched again under section 396.3.
This tool applies 49 CFR 393.60, 393.61 and 393.78, plus Appendix G items 12 and 13, to your inputs. Confirm the result against your state inspection rules and your carrier policy before acting. State law can be stricter than the federal rule.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This checker applies the federal glazing rules in 49 CFR 393.60, 393.61 and 393.78 — state law and carrier policy can be stricter, so confirm the result against your state inspection rules before you rely on it.
Quick answer: A cracked windshield is DOT legal if the crack is not intersected by any other crack, under 49 CFR 393.60(c)(2). A chip or damaged area is legal if it fits under a 3/4 inch disc and sits at least 3 inches from any other damaged area. Tint must transmit at least 70 percent of the light. A dash cam or other vehicle safety technology may mount within 8.5 inches below the upper edge of the wiper swept area or within 7 inches above its lower edge. Windshield glass is never out of service: only the driver side wiper is, in wet weather. This checker tests each item against sections 393.60, 393.61 and 393.78, plus Appendix G items 12 and 13.
What does DOT say about a cracked windshield?
The federal rule is 49 CFR 393.60(c). It says each windshield shall be free of discoloration or damage in the area extending upward from the height of the top of the steering wheel, excluding a 2 inch border at the top of the windshield and a 1 inch border at each side. That protected area is the part of the glass the driver looks through. Damage anywhere else on the windshield is outside the rule. A crack along the bottom edge, below the top of the steering wheel, is not a section 393.60(c) violation, whatever it looks like.
Three exceptions sit inside the rule. The first covers tinting that meets the 70 percent transmittance rule in section 393.60(d). The second covers any crack that is not intersected by any other crack. The third covers any damaged area that can be covered by a disc 3/4 inch in diameter, if it is not closer than 3 inches to any other similarly damaged area. A windshield with damage that fits one of the three exceptions passes the federal rule at roadside. A windshield with damage that fits none of them fails it.
Note what the rule does not say. It sets no maximum crack length. A single crack can run from one side of the windshield to the other and still pass, provided no other crack crosses it. It sets no limit on the number of cracks, provided none of them intersect. It does not require the glass to be perfect. It requires the protected area to be free of damage that falls outside the three exceptions. That is a narrower test than most drivers expect. It is the test an inspector applies at roadside.
The rule also requires the glazing itself to meet Federal Motor Vehicle Safety Standard 205 and to carry the FMVSS 205 marking, under section 393.60(a), on any vehicle built on or after December 25, 1968. A replacement windshield without the marking is a separate violation, even if the glass is undamaged. Every bus, truck and truck tractor must have a windshield under section 393.60(b), mounted using the full periphery of the glazing material. The checker above tests the condition rules. The marking and mounting rules are worth a look whenever a windshield is replaced.
How big can a windshield crack be before DOT fails it?
At roadside, length does not matter. The only crack test in section 393.60(c)(2) is intersection: a crack that is not intersected by any other crack is excepted, however long it runs. Two cracks that cross each other fail the test, even if each one is short. A star break with several short cracks radiating from one impact point is a judgment call for the inspector, because the radiating cracks meet at the center. The safe reading is that cracks sharing a common origin intersect at that point, so treat a star break with radiating cracks as intersected.
Chips and damaged areas follow a different test. Section 393.60(c)(3) excepts any damaged area that can be covered by a disc 3/4 inch in diameter, if it is not closer than 3 inches to any other similarly damaged area. Measure the damaged area across its widest point. A bullseye chip 1/2 inch across passes. A chip 1 inch across fails. Two chips 1/2 inch across pass if they sit 3 inches or more apart. They fail if they sit closer. The 3 inch gap is measured from the edge of one damaged area to the edge of the other.
The annual inspection adds a test the roadside rule lacks. Appendix G item 12(2) excepts only a crack not over 1/4 inch wide, if not intersected by any other crack. A crack wider than 1/4 inch fails the annual inspection even though it is legal at roadside. Crack width is the width of the crack line itself, not its length. Most fresh cracks are hairline thin, well under 1/4 inch. A crack that has been filled with resin, or one that has spread and opened, can exceed the limit. Measure the widest point with a ruler before the inspection.
| Damage | Roadside rule, section 393.60 | Annual inspection, Appendix G item 12 |
|---|---|---|
| Single crack, not intersected | Legal, any length | Legal only if not over 1/4 inch wide |
| Cracks that intersect | Violation | Fail |
| Chip up to 3/4 inch, 3 inches from other damage | Legal | Legal |
| Chip over 3/4 inch across | Violation | Fail |
| Two chips closer than 3 inches apart | Violation | Fail |
| Discoloration or vision reducing matter | Violation | Fail, except factory tint |
Discoloration gets no exception beyond tinting. Haze, clouding, delamination and scratches that reduce vision in the protected area fail section 393.60(c). Pitting from years of road grit is the common case. Light pitting that does not reduce vision is a judgment call. Heavy pitting that scatters headlight glare at night is vision reducing matter. An inspector can cite it. If the glass looks frosted in the headlights of oncoming traffic, it is time for a new windshield.
Can a cracked windshield put a truck out of service?
No. Windshield glass is never out of service. The CVSA North American Standard Out-of-Service Criteria, Part II, contains no item covering windshield glazing. A cracked windshield is a violation of section 393.60, citable at roadside. It goes on the inspection report. It does not put the vehicle out of service, however bad the crack looks. A driver with a cracked windshield drives away from the inspection with a citation, not a tow.
The one glass related item that is out of service is the driver side wiper, only in wet weather. CVSA places the vehicle out of service when the driver side wiper is inoperative while it is raining or the road is wet. A dead passenger side wiper is a violation, not an out of service condition. A dead driver side wiper on a dry day is a violation too. It becomes an out of service condition the moment it rains. The checker flags that risk before the weather turns.
The distinction matters because drivers and carriers confuse the two outcomes. A violation costs a citation and CSA points. An out of service order stops the vehicle until the defect is fixed. It costs the carrier far more in time and money. A cracked windshield is the first kind of problem. A dead wiper in the rain is the second. Fix the wiper first if both are wrong. The FMCSA Fine Calculator shows what a Part 393 violation can cost when an enforcement case follows.
The annual inspection is a third outcome, separate from both. A vehicle fails the annual inspection if it has any defect listed in Appendix G, including a crack over 1/4 inch wide under item 12 or any inoperative wiper under item 13. A failed annual inspection means no valid inspection sticker until the defect is repaired and the vehicle passes a re-inspection. The Annual Inspection Due-Date Tracker works out when the next annual inspection falls due. The DVIR Checker works out what a driver must report and what a carrier must repair before the next dispatch.
What is the windshield tint limit for a truck?
Section 393.60(d) allows tinting on the windshield and on the windows to the immediate right and left of the driver, provided the parallel luminous transmittance through the tinted glazing is not less than 70 percent of the light at normal incidence. In plain terms, at least 70 percent of the light must pass through the glass. A film rated 70 percent lets 70 percent through. A film rated 50 percent lets only half through. It fails the rule. The limit applies to the glass plus the film together, not to the film alone.
Factory glass is already tinted. Most truck windshields leave the factory with a light green or gray tint that transmits roughly 75 to 80 percent of the light. Adding an aftermarket film on top of factory tint stacks the two: a 70 percent film on 75 percent glass transmits about 52 percent, well below the limit. That is how most tint citations happen. The driver buys a legal film and applies it to already tinted glass. The combination fails. Measure the installed glass with a tint meter, not the film on its own.
The transmittance restriction does not apply to other windows on the vehicle. Sleeper windows, rear windows and cargo area windows can carry darker tint under the federal rule. State law is a different matter: many states set their own tint limits for every window. The stricter state rule governs on that state roads. The federal rule is the floor. Check the state rules for every state the truck runs in.
One wrinkle sits in the annual inspection standard. Appendix G item 12 excepts only tinting applied at the time of manufacture. Read strictly, that wording does not cover aftermarket tint, even tint that meets the 70 percent rule in section 393.60(d). Most inspectors accept compliant aftermarket tint, but the text gives a strict inspector room to fail it. Keep the transmittance certificate or the film specification sheet with the vehicle, so the inspector can see the number instead of guessing it. The checker notes this wrinkle whenever aftermarket tint is entered.
Where can a dash cam mount on a truck windshield?
Vehicle safety technology has its own mounting rule. Section 393.60(e)(1)(ii) says devices with vehicle safety technology must be mounted not more than 8.5 inches below the upper edge of the area swept by the windshield wipers, or not more than 7 inches above the lower edge of that area, outside the driver sight lines to the road and to highway signs and signals. Two zones are permitted: a strip near the top of the swept area plus a strip near the bottom. The middle of the swept area is not permitted. A dash cam stuck in the center of the windshield fails the rule.
The 8.5 inch figure is current as of 2018. The original 2016 rule allowed only 4 inches below the upper edge of the swept area. FMCSA widened the top zone to 8.5 inches in May 2018, because cameras and sensors mounted behind the rearview mirror needed more room. Older guides still print the 4 inch figure. The checker uses 8.5 inches, verified against the current eCFR text.
Section 393.5 defines vehicle safety technology broadly. It includes fleet incident management systems, performance and behavior management systems, speed management systems, lane departure warning, forward collision warning or mitigation, active cruise control, transponders, braking warning and braking assist systems, driver camera systems, attention assist warning, Global Positioning Systems plus traffic sign recognition. It includes systems and devices that contain cameras, lidar, radar, sensors plus video. A dash cam, a GPS unit, a toll transponder and a lane departure camera all count. A phone mount is a gray area: a phone running GPS navigation is arguably a GPS device under the definition, but a phone showing anything else is not vehicle safety technology.
Antennas and similar devices follow a different rule. Section 393.60(e)(1)(i) says they must not be mounted more than 6 inches below the upper edge of the windshield. They must sit outside the area swept by the wipers and outside the sight lines. Note the reference edge: the upper edge of the windshield, not the upper edge of the swept area. Antennas sit in the top strip of the glass, above the wiper sweep. A CB antenna or a radio antenna mounted low on the glass fails the rule.
| Device | Permitted zone | Reference edge | Swept area |
|---|---|---|---|
| Vehicle safety technology: dash cam, GPS, transponder | Within 8.5 inches below the top of the swept area, or within 7 inches above the bottom | Swept area edges | May sit inside the swept area, within the zones |
| Antenna or similar device | Within 6 inches below the top of the windshield | Windshield upper edge | Must sit outside the swept area |
| CVSA decal or legally required sticker | Within 4 1/2 inches of the bottom of the windshield | Windshield bottom edge | Must sit outside the swept area |
The sight lines rule applies to every device. Section 393.60(e)(1) requires every mounted device to sit outside the driver sight lines to the road and to highway signs and signals. A device in a permitted zone can still fail if it blocks the driver view of a traffic signal or a road sign. The test is practical: sit in the driver seat and look at the road, the signs and the signals. If the device blocks any of them, move it.
Can you put stickers on a truck windshield?
Only two kinds. Section 393.60(e)(2) allows CVSA inspection decals and stickers or decals required under federal or state law on the windshield. Anything else is not permitted. A company logo sticker, a parking permit from a shipper, a novelty decal or a toll sticker that no law requires has no exception under the rule. In the protected area, an unauthorized sticker is vision reducing matter under section 393.60(c).
Permitted decals have placement limits. They may be placed at the bottom or sides of the windshield, provided they do not extend more than 4 1/2 inches from the bottom of the windshield and are located outside the area swept by the wipers and outside the driver sight lines. The CVSA inspection decal goes on the lower corner of the windshield for exactly this reason. A decal stuck in the middle of the glass, or high on the glass, fails the rule even if it is a CVSA decal.
The bottom strip is narrow. On a typical truck windshield, 4 1/2 inches from the bottom reaches just above the dashboard line. Two or three decals stacked in that strip can still comply, provided each one stays inside the limit and outside the swept area. The wiper sweep reaches low on most windshields, so check the sweep before placing a decal. A decal under the wiper blade path fails the swept area test.
What are the side window rules for trucks?
Section 393.61 requires each truck and truck tractor to have at least one window on each side of the driver compartment. Each window must have a minimum area of 200 square inches, formed by a rectangle 13 inches by 17 3/4 inches. The maximum radius of the corner arcs is 6 inches. The long axis of the rectangle must not make an angle of more than 45 degrees with the surface on which the unladen vehicle stands. The rule is about the size of the opening the driver can see through, not about the glass itself.
Two exceptions exist. Trucks in armored car service are excepted from the whole section. And if the cab is designed with a folding door or doors, or with clear openings where doors or windows are customarily located, no windows are required in those locations. A cab with an open doorway design does not need glass in the opening. A standard cab with a window removed or blocked does not qualify for either exception.
Side windows beside the driver carry the same 70 percent tint limit as the windshield under section 393.60(d). Windows further back do not. A dark tint on the driver door window fails the same way a dark windshield tint fails. The checker tests the side window size and the tint together, so a cab with a small window and dark film fails on both counts.
What happens when a wiper fails?
Section 393.78(a) requires every bus, truck and truck tractor built on or after December 25, 1968 to have a windshield wiping system meeting FMVSS 104 and a windshield washing system meeting FMVSS 104. A wiper that does not work, or a washer that does not spray, violates the section. The rule covers the system, not just the blade: a burned out motor, a broken linkage, a missing arm or a clogged washer jet all count.
The annual inspection is absolute on wipers. Appendix G item 13 fails any power unit that has an inoperative wiper, or missing or damaged parts that render it ineffective. There is no exception for the passenger side and no exception for a wiper that works slowly. One dead wiper fails the inspection. The same item covers parts: a wiper arm that does not hold the blade against the glass renders the wiper ineffective, even if the motor runs.
At roadside, the consequence depends on the weather and the side. A dead driver side wiper in wet weather is out of service under CVSA criteria. A dead passenger side wiper is a violation only. A dead driver side wiper on a dry day is a violation only, until it rains. The practical lesson is to fix a dead wiper the day it fails. Weather changes faster than a repair schedule. A wiper that is a citation at noon becomes an out of service order in an afternoon storm.
A driver who finds a dead wiper must report it on the DVIR. Section 396.13 requires the driver to inspect the vehicle and report defects. Section 396.3 requires the carrier to repair safety related defects before the vehicle is dispatched again. The DVIR Checker works out what must be reported and what must be repaired. The Pre-Trip Inspection Checklist covers wipers and glazing as part of the daily walk around, with the out of service flags for each item.
Roadside inspection or annual inspection: which rule is stricter?
The two inspections apply different standards to the same glass. The roadside inspection applies Part 393, the equipment rules. The annual inspection applies Appendix G to Subchapter B, the minimum periodic inspection standards. The two standards agree on most points and differ on two: crack width and tint.
Crack width is the big difference. Section 393.60(c)(2) excepts any crack that is not intersected by any other crack, with no width limit. Appendix G item 12(2) excepts only a crack not over 1/4 inch wide, if not intersected. A crack 1/2 inch wide and 2 feet long is legal at roadside and fails the annual inspection. That is the most common surprise in the annual inspection, because the driver has been driving past roadside inspections with the same crack for months.
Tint is the second difference. Section 393.60(d) allows any tinting that transmits at least 70 percent of the light, factory or aftermarket. Appendix G item 12(1) excepts only tinting applied at the time of manufacture. The annual standard is narrower on paper, though most inspectors accept compliant aftermarket tint in practice. The checker flags the wrinkle so the driver carries the paperwork.
| Item | Roadside, Part 393 | Annual, Appendix G |
|---|---|---|
| Crack, not intersected | Legal, any width | Legal only if not over 1/4 inch wide |
| Crack, intersected | Violation | Fail |
| Chip, 3/4 inch disc, 3 inches apart | Legal | Legal |
| Tint, 70 percent or better | Legal, factory or aftermarket | Factory tint excepted; aftermarket tint a judgment call |
| Dead wiper | Violation; driver side out of service in wet weather | Fail, any wiper |
| Decal over 4 1/2 inches from the bottom | Violation | Fail, item 12(4) points back to section 393.60 |
Plan around the stricter standard. A windshield that passes the annual inspection passes roadside too. A windshield that only just passes roadside can still fail the annual. The Annual Inspection Due-Date Tracker works out when the next annual inspection falls due, so a crack can be repaired on a schedule instead of in a panic. The Tire Compliance Checker covers the other inspection item drivers get wrong most often, with the same two tier structure: a roadside rule and a stricter annual rule.
How do you use the Windshield and Glass Checker?
Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the verdict change.
- Describe the windshield damage: the type, the location, plus the measurements.
- Enter the tint transmittance and say which windows carry the tint.
- Describe each mounted device and decal, with the distances from the windshield edges.
- Confirm the side windows, the wipers, the washer, plus the weather.
- Read the verdict, the checks, plus the actions.
- Copy the summary for the vehicle file or the repair order.
Measure before you enter. The crack width, the chip diameter, the distance between damaged areas and the mounting distances are all measurements, not guesses. A tape measure and a minute of care give a verdict you can rely on. A guess gives a verdict you cannot defend at an inspection.
Use the tool before an inspection, not during one. The verdict tells you what to fix and in what order: an out of service wiper first, a violation second, an annual inspection item third. Copy the summary and hand it to the shop with the vehicle. The repair order then matches the regulation. The inspector sees a vehicle that was fixed on purpose, not by luck.
Questions drivers ask
Can you drive a truck with a cracked windshield?
Yes, if the crack is not intersected by any other crack. Section 393.60(c)(2) excepts any crack that is not intersected by any other crack, whatever its length. A crack that crosses another crack is a violation. At the annual inspection the rule is stricter: Appendix G item 12(2) fails any crack over 1/4 inch wide, even if it is not intersected.
Is a cracked windshield an out of service violation?
No. Windshield glass is never out of service. No CVSA Part II item covers glazing, so a cracked windshield is a section 393.60 violation only. The only glass related out of service item is the driver side wiper, only in wet weather. A dead driver side wiper in the rain puts the vehicle out of service.
What is the DOT tint limit for a truck windshield?
Tint on a truck windshield must transmit at least 70 percent of the light, under section 393.60(d). The same limit applies to the windows to the immediate right and left of the driver. Other windows on the vehicle have no federal transmittance limit. The 70 percent figure covers the glass plus the film together, so aftermarket film on factory tinted glass often fails.
Where can I mount a dash cam on a truck windshield?
A dash cam is vehicle safety technology under section 393.5, so section 393.60(e)(1)(ii) applies. Mount it within 8.5 inches below the upper edge of the area swept by the wipers, or within 7 inches above the lower edge of that area, outside the driver sight lines to the road and to highway signs and signals. The middle of the swept area is not permitted.
How big can a windshield chip be under DOT rules?
A damaged area is legal if it can be covered by a disc 3/4 inch in diameter and sits at least 3 inches from any other similarly damaged area, under section 393.60(c)(3). A chip wider than 3/4 inch fails. Two chips closer than 3 inches apart fail, even if each one is small. Measure the damaged area across its widest point.
Does a dead windshield wiper fail the DOT annual inspection?
Yes. Appendix G item 13 fails any power unit that has an inoperative wiper, or missing or damaged parts that render it ineffective. There is no exception for the passenger side. A dead driver side wiper is also an out of service item in wet weather under CVSA criteria. Fix a dead wiper before the next dispatch.
Related tools
- Annual Inspection Due-Date Tracker: work out when the next annual inspection falls due and what Appendix G requires.
- DVIR Checker: work out what a driver must report on the driver vehicle inspection report and what a carrier must repair before the next dispatch.
- Tire Compliance Checker: check tread depth, tire condition and load ratings against 49 CFR 393.75, with the same two tier roadside and annual structure.
- Pre-Trip Inspection Checklist: the daily walk around covering wipers, glazing, lights, brakes and tires, with the out of service flags for each item.
- FMCSA Fine Calculator: work out what a Part 393 equipment violation can cost when an enforcement case follows.
Sources
- 49 CFR 393.60, Glazing in specified openings (eCFR, read verbatim Nov 19, 2026; last amended 87 FR 12604, Mar 7, 2022)
- 49 CFR 393.61, Truck and truck tractor window construction (eCFR, read verbatim Nov 19, 2026)
- 49 CFR 393.78, Windshield wiping and washing systems (eCFR, read verbatim Nov 19, 2026)
- 49 CFR 393.5, Definitions, vehicle safety technology (eCFR, read verbatim Nov 19, 2026)
- Appendix G to Subchapter B, Minimum periodic inspection standards, items 12 and 13 (eCFR, read verbatim Nov 19, 2026; eCFR labels the same text Appendix A to Part 396)
- 83 FR 22878, May 17, 2018 (safety technology mounting zone widened from 4 inches to 8.5 inches below the upper edge of the swept area)