One package at a time. This checker lists the labels and markings for one package under 49 CFR 172.300 through 172.338 and 172.400 through 172.450. Marking and labeling are the duties of the person who offers the material for transportation. A carrier accepting the load uses the same lists to check the package before taking it.
Enter the material and the package, then check the lists. Every answer updates as you change each field.
The material
Subsidiary hazards (check each one that applies)
The package
Extra markings
Class 7 details
Class 1 details
Air transport
Your checks (answer each one after you look at the package)
Checks outstanding: confirm before shipping
Class 3 flammable liquid in a non-bulk package: 1 label and 2 markings
The lists below show every label and marking this package needs. 6 checks still need confirming.
Required labels
- FLAMMABLE LIQUID label (section 172.419). Red background, flame symbol.
Required markings
- Proper shipping name and identification number preceded by UN, NA or ID as appropriate (section 172.301(a)(1)). Identification number characters at least 12 mm high.
- Package orientation arrows on two opposite vertical sides of the package, arrows pointing up, black or red on a white or contrasting background (section 172.312(a)(2)). Pack the package with closures upward.
Exceptions applied
- No consignor or consignee name and address marking is required for a package transported by highway only that will not be transferred from one motor carrier to another (section 172.301(d)(1)).
Checks
| Check | Result | Detail |
|---|---|---|
| Labels required | Pass | 1 label listed above, primary first, then subsidiary (section 172.400(b) and 172.402). |
| Label size | Info | Each diamond label at least 100 mm (3.9 in) on each side, with a solid line inner border about 5 mm inside the edge (section 172.407(c)(1)). Dimensions may be reduced proportionally where the package size requires it. |
| Duplicate labels | Info | One of each required label is enough on this package. Duplicate labels are required only for packages and overpacks of 1.8 cubic meters or more, radioactive packages, portable tanks under 1,000 gallons and IBCs of 1.8 cubic meters or more (section 172.406(e)). |
| Markings required | Pass | 2 markings listed above. |
| Orientation arrows | Pass | Arrows on two opposite vertical sides, pointing up (section 172.312(a)(2)). |
| Exceptions applied | Info | 1 exception applied, listed above. |
| Labels off the bottom | Check | Labels sit on a surface other than the bottom of the package (section 172.406(a)(1)(i)). |
| Labels near the shipping name | Check | Labels sit on the same surface as and near the proper shipping name marking, primary and subsidiary labels within 150 mm of each other (section 172.406(a)(1)(ii) and (c)). |
| Labels durable and visible | Check | Labels are durable and weather resistant, on a contrasting background or with an outer border. Nothing obscures them (sections 172.406(d), 172.406(f) and 172.407(a)). |
| Label size | Check | Each diamond label measures at least 100 mm on each side, or is reduced proportionally for a small package with the symbol still clearly visible (section 172.407(c)(1)). |
| No old or conflicting labels | Check | No label or marking from an earlier shipment stays on the package (sections 172.303 and 172.401). |
| Markings legible and clear | Check | Markings are durable, in English, on a sharply contrasting background, unobscured by labels or attachments (section 172.304). |
The figures
| Figure | Value | Note |
|---|---|---|
| Labels required | 1 | Physical labels, counting duplicates for Class 7 and fissile material. |
| Markings required | 2 | Markings listed above, including the limited quantity marking where it applies. |
| Label size | 100 mm (3.9 in) per side | Diamond (square-on-point), solid line inner border about 5 mm inside the edge (section 172.407(c)(1)). |
| Identification number height | at least 12 mm high | Section 172.301(a)(1) for non-bulk packagings, section 172.302(b) for bulk packagings. |
| Exceptions applied | 1 | Each exception is listed above with its section. |
| Duplicate labels | No, one side | Section 172.406(e). |
What to do
- Confirm the label codes for the exact material in column 6 of the Hazardous Materials Table (section 172.101). The table governs where it differs from the class rules used here.
- Check the package again after loading: labels and markings must still be visible and unobscured.
Notes
- Marking and labeling are the duties of the person who offers the material for transportation (section 172.300(a)). A carrier accepting the load checks that the package is properly marked and labeled before taking it.
- A placard on the vehicle does not replace the labels on a non-bulk package. Placards replace labels only for the bulk packagings, portable tanks and overpacks listed in section 172.400(a).
This checker applies 49 CFR 172.300 through 172.338 and 172.400 through 172.450 to your answers. Confirm the label codes in column 6 of the Hazardous Materials Table for the exact material before you rely on a result.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not legal advice — check the current regulation and your company policy before you rely on a result.
Quick answer: A hazmat package needs a diamond label for its hazard class, a label for each subsidiary hazard and markings that name the material: the proper shipping name and the UN or NA identification number. Labels measure at least 100 mm (3.9 in) on each side and sit on a surface other than the bottom, near the shipping name marking. Liquid hazmat in inner packagings also needs orientation arrows on two opposite vertical sides. Limited quantity packages trade the labels for a square-on-point limited quantity marking by highway. Bulk packagings are placarded and marked with identification numbers instead of labeled. This checker lists every label and marking for one package, with the section that requires each one.
What labels does a hazmat package need?
Every non-bulk package of hazardous material needs a label for its primary hazard class or division, plus a label for each subsidiary hazard the material carries. Section 172.400 sets the duty and points to the table in section 172.400(b) for the label name. Column 6 of the Hazardous Materials Table in section 172.101 gives the label codes for each listed material by name. The table governs where it differs from the class rules. This checker applies the class rules and tells you to confirm the exact codes in column 6 before you rely on a result.
The primary label follows the class. Explosives take an EXPLOSIVES label for their division, orange, with the division number and the compatibility group letter. Flammable gas takes FLAMMABLE GAS, red. Non-flammable gas takes NON-FLAMMABLE GAS, green. Poison gas takes POISON GAS. Flammable liquid takes FLAMMABLE LIQUID, red. Flammable solid, spontaneously combustible material and dangerous when wet material take their own named labels. Oxidizers take OXIDIZER, yellow. Organic peroxides take ORGANIC PEROXIDE, red over yellow. Division 6.1 material takes POISON, or POISON INHALATION HAZARD when the material is poisonous by inhalation. Infectious substances take INFECTIOUS SUBSTANCE. Radioactive material takes RADIOACTIVE WHITE-I, YELLOW-II or YELLOW-III by category. Corrosive material takes CORROSIVE. Class 9 takes CLASS 9. Lithium batteries take the LITHIUM BATTERY label.
Two classes break the pattern. A combustible liquid has no label at all: the table in section 172.400(b) lists none for it. And a combustible liquid in a non-bulk packaging is not even regulated unless it is a hazardous substance, hazardous waste or marine pollutant, under section 173.150(f)(2). The checker routes that case to a not-regulated result rather than inventing a label.
Subsidiary hazards follow the table in section 172.402(a)(2). At Packing Group I, a subsidiary label is required for Class 3, Division 4.3, Division 5.1, Division 6.1 and Class 8; Divisions 4.1 and 4.2 cannot be subsidiary hazards at Packing Group I. At Packing Group II, all seven subsidiary hazards need a label. At Packing Group III, all seven need a label except a Class 3 subsidiary for a material with a flash point at or above 38 C (100 F) transported by rail or highway. Class 1 and Class 2 materials have their own subsidiary rules in section 172.402(e) through (g): explosives add POISON or POISON INHALATION HAZARD at Packing Group I or II, Division 2.2 adds OXIDIZER for an oxidizing gas and Division 2.3 adds FLAMMABLE GAS, OXIDIZER or CORROSIVE as the subsidiary hazard requires.
Two narrow exceptions remove a subsidiary label. No Division 6.1 subsidiary label is required on a Class 8 package when the toxicity comes solely from corrosive destruction of tissue rather than systemic poisoning. No Division 4.1 subsidiary label is required on a package bearing a Division 4.2 label. Both sit in section 172.400a(c). The checker asks about each one where it can apply.
| Hazard class or division | Primary label | Section |
|---|---|---|
| 1.1, 1.2, 1.3 | EXPLOSIVES 1.1, 1.2, 1.3 (orange) | 172.411 |
| 1.4, 1.5, 1.6 | EXPLOSIVES 1.4, 1.5, 1.6 (orange) | 172.411 |
| 2.1 | FLAMMABLE GAS (red) | 172.417 |
| 2.2 | NON-FLAMMABLE GAS (green) | 172.415 |
| 2.3 | POISON GAS | 172.416 |
| 3 | FLAMMABLE LIQUID (red) | 172.419 |
| 3, combustible liquid | None | 172.400(b) |
| 4.1 | FLAMMABLE SOLID | 172.420 |
| 4.2 | SPONTANEOUSLY COMBUSTIBLE | 172.422 |
| 4.3 | DANGEROUS WHEN WET (blue) | 172.423 |
| 5.1 | OXIDIZER (yellow) | 172.426 |
| 5.2 | ORGANIC PEROXIDE | 172.427 |
| 6.1, poisonous by inhalation | POISON INHALATION HAZARD | 172.429 |
| 6.1, other | POISON | 172.430 |
| 6.2 | INFECTIOUS SUBSTANCE | 172.432 |
| 7 | RADIOACTIVE WHITE-I, YELLOW-II, YELLOW-III | 172.436, 172.438, 172.440 |
| 8 | CORROSIVE | 172.442 |
| 9 | CLASS 9 | 172.446 |
| 9, lithium batteries | LITHIUM BATTERY | 172.447 |
What markings does a hazmat package need?
Markings are the words and numbers on the package. Labels are the diamond hazard warnings. A package usually needs both. The two sets of rules live in different subparts: markings in subpart D, sections 172.300 through 172.338; labels in subpart E, sections 172.400 through 172.450.
The base marking for a non-bulk package is the proper shipping name and the identification number, preceded by UN, NA or ID as appropriate, under section 172.301(a)(1). The identification number must be at least 12 mm high on an ordinary package. Smaller packages get smaller letters: at least 6 mm for a package of 30 liters or 30 kg or less and for a cylinder of 60 liters water capacity or less, with a size appropriate for the package at 5 liters or 5 kg or less. The shipping name and number on the package must match the description on the shipping paper. The Hazmat Shipping Paper Checker covers the paper side of that match.
Three more markings apply often enough to check every time. A generic or n.o.s. shipping name needs its technical name in parentheses next to the shipping name, under section 172.301(b), except on the outer package of a Division 6.1 material the rule names separately and except for Division 6.2, where no technical name should be marked. A package shipped under a DOT special permit carries DOT-SP followed by the permit number, under section 172.301(c). A hazardous substance at or above its reportable quantity carries the letters RQ plus the substance name in parentheses, under section 172.324. That marking applies to limited quantity packages too.
The consignor or consignee name and address marking surprises shippers because its exceptions cover most truckload moves. Section 172.301(d) requires the marking except when the package travels by highway only and will not be transferred from one motor carrier to another, or when it rides in a carload, truckload or freight container lot shipped whole from one consignor to one consignee. A single-carrier highway move needs no consignor marking. An interline move does.
Special materials add their own markings. Liquid hazmat in inner packagings needs orientation arrows. Material poisonous by inhalation needs an INHALATION HAZARD marking on a bulk packaging, though not on a labeled package whose label already carries the words. Class 1 material needs its EX-number. A marine pollutant needs the fish and tree mark. An elevated temperature material in bulk needs HOT, or MOLTEN ALUMINUM or MOLTEN SULFUR. A Class 7 package over 50 kg needs its gross mass marked, plus its TYPE designation and the USA design code. The checker asks about each of these and lists only the markings that apply to the package in front of you.
How big must hazmat labels and markings be?
Size rules are the easiest part of the regulation to get wrong, because the numbers differ by item and by package size. The headline number is 100 mm: each diamond label must be at least 100 mm (3.9 in) on each side, with a solid line inner border about 5 mm inside the edge, under section 172.407(c)(1). Where the package is too small for a full-size label, the dimensions and features may be reduced proportionally, provided the symbol and other elements stay clearly visible. A shrunken label with an unreadable symbol fails the rule even though the reduction itself is allowed.
The details inside the label have their own minimums. The hazard class or division number in the lower corner must be at least 6.3 mm and at most 12.7 mm high. Where the label shows its name, the letters must be at least 7.6 mm high, except that Spontaneously and When Wet may be 5.1 mm. For EXPLOSIVE 1.4, 1.5 and 1.6 labels the division number must be at least 30 mm high. The hazard words themselves are not required on a primary or subsidiary label for Classes 1, 2, 3, 4, 5, 6 and 8 under section 172.405(a): the symbol and the number carry the meaning. A label with no words is a compliant label.
Durability is a size rule of a different kind. Each label must be durable and weather resistant, able to withstand 30 days of exposure to the conditions of transport without deterioration or a substantial change in color, under section 172.407(a). A paper label that dissolves in rain fails even if it measures exactly 100 mm on the day it is applied.
Marking sizes run on a separate ladder. Identification numbers on non-bulk packages measure at least 12 mm high, or 6 mm on a package of 30 liters or 30 kg or less, under section 172.301(a)(1). Bulk packagings measure larger: 12 mm for a portable tank under 1,000 gallons, 25 mm for an IBC, 50 mm for a cargo tank and other bulk packagings, 100 mm for a rail car, under section 172.302(b). The OVERPACK marking needs letters at least 12 mm high. The limited quantity mark measures at least 100 mm per side, or 50 mm reduced. The marine pollutant mark measures at least 100 mm per side on a non-bulk package and 250 mm on a large bulk packaging. The EMPTY label measures at least 152 mm (6 in) per side with letters at least 25.4 mm (1 in) high.
| Item | Minimum size | Section |
|---|---|---|
| Diamond hazard label | 100 mm per side | 172.407(c)(1) |
| Label inner border offset | About 5 mm inside the edge | 172.407(c)(1) |
| Class or division number on a label | 6.3 mm to 12.7 mm high | 172.407(c)(3) |
| Label name letters | 7.6 mm high | 172.407(c)(4) |
| ID number, non-bulk package | 12 mm high | 172.301(a)(1) |
| ID number, package 30 L or 30 kg or less | 6 mm high | 172.301(a)(1) |
| ID number, portable tank under 1,000 gal | 12 mm high | 172.302(b)(2) |
| ID number, IBC | 25 mm high | 172.302(b)(2) |
| ID number, cargo tank and other bulk | 50 mm high | 172.302(b)(3) |
| Orange panel ID numerals | 100 mm high | 172.332(b)(1) |
| OVERPACK letters | 12 mm high | 173.25(a)(4) |
| Limited quantity mark | 100 mm per side, 50 mm reduced | 172.315(a)(2) |
| MARINE POLLUTANT mark, non-bulk | 100 mm per side | 172.322(e)(2) |
| MARINE POLLUTANT mark, large bulk | 250 mm per side | 172.322(e)(2) |
| EMPTY label | 152 mm per side | 172.450(a)(1) |
Where do labels go on a hazmat package?
Placement is governed by section 172.406. The first rule is the one inspectors cite most: each label must be printed on or affixed to a surface other than the bottom of the package. A label on the bottom is a violation even if it is the right label in the right size. Where the package dimensions allow, the label sits on the same surface as the proper shipping name marking and near it, so a responder reads the name and the hazard together.
Primary and subsidiary labels go next to each other. The rule treats labels within 150 mm (6 in) of one another as next to each other. A subsidiary label on the far side of a drum from its primary label fails the placement rule even though both labels are present. Each label needs a background color that contrasts with the label, or a dotted or solid line outer border that makes the label stand out. A red FLAMMABLE LIQUID label on a red drum with no border is hard to see. The rule says so.
Most packages need one of each label. Duplicate labeling applies to a short list in section 172.406(e): each package or overpack with a volume of 1.8 cubic meters (64 cubic feet) or more, each non-bulk package holding radioactive material, each DOT 106 or 110 multi-unit tank car tank, each portable tank under 1,000 gallons, each freight container or aircraft unit load device between 1.8 and 18 cubic meters plus each IBC of 1.8 cubic meters or more. Those carry one of each required label on at least two sides or ends, other than the bottom. Class 7 packages already carry two identical radioactive labels on opposite sides under section 172.403(f), so the duplicate rule is met by the category rule.
Small, round and awkward packages get relief. A label may go on a securely affixed tag, or be affixed by other suitable means, on a package that contains no radioactive material and is smaller than the required label, on a cylinder or on a package with a surface so irregular that a label cannot be affixed satisfactorily. A label on a tag is a compliant label when the package qualifies. What never qualifies is a label the loader cannot see: section 172.406(f) requires every label to be clearly visible and not obscured by markings or attachments.
Do labels and placards do the same job?
No. A label goes on a package. A placard goes on a vehicle, a freight container or a bulk packaging. Both warn of the hazard with the same diamond shapes and colors, but they answer different questions: the label tells a handler what is inside one package; the placard tells a responder what the whole vehicle carries. A placarded truck usually holds labeled packages.
The common misunderstanding is that a placard replaces a label. It does not, for non-bulk packages. Section 172.400(a) allows a placard instead of a label only for a short list of larger containments: bulk packagings under 18 cubic meters other than cargo tanks, portable tanks and tank cars; portable tanks under 1,000 gallons; DOT 106 and 110 multi-unit tank car tanks; and overpacks, freight containers and unit load devices under 18 cubic meters. A placarded cargo tank needs no labels because a cargo tank is never labeled in the first place. A placarded trailer full of drums still needs a label on every drum.
Bulk packagings get identification numbers instead of labels. A cargo tank displays its identification number on an orange panel or a placard, on each side and each end, in numerals 100 mm high. The number is the same UN or NA number that a non-bulk package would carry as a marking, displayed at a size a responder can read from a distance. The Hazmat Placard Checker covers the vehicle side: which placard, when it is required and when the 1,001 lb threshold or a table 1 material triggers it.
One more distinction matters at the dock. Markings identify the material, labels warn of the hazard and placards warn at vehicle scale. All three can be correct at once. All three can fail independently. A drum with a correct label but no shipping name marking fails the marking rule. A drum with a correct marking but a label on the bottom fails the placement rule. The checker lists labels and markings together because an inspector checks both.
What changes for limited quantities?
Limited quantity treatment is the biggest relief in the marking and labeling rules. A limited quantity package needs no hazard label when it moves by highway. It carries the limited quantity marking instead: a diamond, square-on-point, at least 100 mm per side with a border at least 2 mm thick, under section 172.315. The marking may shrink to 50 mm per side where the package size requires it. The limited quantity marking is not a label and must not be confused with one: it has no hazard symbol and no class number.
Three conditions limit the relief. First, the gross weight of a limited quantity package must not exceed 30 kg (66 lb) unless the specific section for the material allows more. Second, the exceptions do not apply at all to Class 1 explosives, Division 2.3 poison gas, Division 6.2 infectious substances, Class 7 radioactive material, or materials poisonous by inhalation under section 173.153(b). Third, air transport takes the relief away: a limited quantity package by air carries the Y-mark, the diamond with a Y in the center, plus the full labels and markings of an ordinary package.
Markings follow a mixed pattern for limited quantities. The package is not subject to the section 172.301 marking rule unless it holds a hazardous substance or hazardous waste, so an ordinary limited quantity package carries no shipping name or identification number marking. But a hazardous substance at or above its reportable quantity still carries the RQ letters and the substance name, under section 172.324(c). A marine pollutant mark is not required on a limited quantity package under section 172.322(d)(4). The checker tracks each of these rather than assuming a limited quantity package carries nothing.
Overpacks complicate the picture. A limited quantity marking must appear on an overpack when the markings on the inner packages are not visible. The 25 mm reduced size is not authorized on an overpack. The overpack rule is covered in the next section.
What labels and markings does an overpack need?
An overpack is an outer enclosure, a shrink-wrapped pallet or a box, that holds one or more packages of hazardous material. It is not itself a package, but section 173.25 treats it almost like one: the overpack must be marked with the proper shipping name and identification number and labeled for each hazardous material inside, unless the markings and labels on the inner packages are visible through it or remain on it. Visibility is the test. A clear shrink wrap that shows a representative label and marking for each material inside saves the work. An opaque overpack needs its own full set.
Three overpack markings are easy to miss. First, the OVERPACK marking itself: letters at least 12 mm high, required when specification packagings are required, unless the specification markings on the inner packages are visible. Second, orientation arrows on the overpack when the inner packages require them, on two opposite vertical sides. Third, the limited quantity marking on the overpack when the inner limited quantity markings are not visible. The checker asks about visibility separately for labels and markings, because the two can differ on the same overpack.
Two compatibility rules bound the overpack. Packages in one overpack must be compatible: a shipment of non-compatible hazardous materials in one overpack is prohibited. The Hazmat Segregation Checker applies the table in section 177.848 to mixed loads. And a single overpack must not contain packages of more than 1,000 pounds of Class 8, Packing Group I material plus Class 5.1 material together. A single carrier collecting small quantities in a consolidation bin gets a narrower exception in section 172.404(c), with a NON-FLAMMABLE GAS label for Division 2.2 material inside.
What happens with empty packagings?
An emptied package is not an unregulated package. Section 173.29(a) says an empty packaging with residue of hazardous material must be offered for transportation and transported in the same manner as when filled. The labels and markings stay on. The shipping description stays the same. A drum with a heel of flammable liquid ships as a drum of flammable liquid.
Relief comes only from cleaning. Under section 173.29(b), a packaging is excepted from the hazardous materials regulations when it is unused, when it has been sufficiently cleaned of residue and purged of vapors to remove any potential hazard, when it has been refilled with a material that is not a hazardous material, or when it holds only the residue of a limited quantity material or a Division 2.2 material at a pressure not exceeding 29 psig. Cleaning alone is not enough: all hazardous material markings, labels and placards must be removed, obliterated or securely covered. The contents must not be a hazardous substance, hazardous waste or marine pollutant. A cleaned drum with a faded FLAMMABLE LIQUID label still on it is not an excepted package.
Empty Class 7 packages follow their own rule. A packaging that previously contained radioactive material and is empty, uncontaminated and properly closed under section 173.428 carries the EMPTY label: white, each side at least 152 mm (6 in), with EMPTY in black letters at least 25.4 mm (1 in) high, under section 172.450. The EMPTY label is a Class 7 label only. It does not belong on an empty flammable liquid drum.
The practical test for a driver or loader is simple. If the package still smells of the material, still shows residue, or still carries its labels, treat it as full. If it has been cleaned, purged and stripped of every hazmat marking, it travels as ordinary freight. The checker asks about the package state and routes a cleaned package to a no-requirement result.
How do you use the Hazmat Label and Marking Checker?
Work through the form in order. Start with the material: mode, hazard class, packing group and whether the material is poisonous by inhalation. Add each subsidiary hazard the material carries. Then describe the package: its type, its size, whether it is a limited quantity, an overpack or an empty packaging. Answer the extra marking questions for a marine pollutant, a hazardous substance, a special permit or a technical name. The label and marking lists update as you change each field, so you can check a second package by changing only the fields that differ.
Finish with the six checks at the bottom of the form. They are the physical inspection: labels off the bottom, labels near the shipping name, labels durable and visible, labels full size, no old or conflicting labels and markings legible and clear. The checker cannot see the package, so it cannot pass them for you. It asks. It marks the result outstanding until you answer.
When the verdict reads ready to ship, copy the summary for your records. The summary lists every label and marking the package needs, with the section that requires each one, so a second person can verify the package against it without reopening the tool.
- Enter the hazard class or division, packing group and mode of transport.
- Check each subsidiary hazard the material carries.
- Describe the packaging type, size and limited quantity or overpack status.
- Answer the extra marking questions for marine pollutants, RQ materials and special permits.
- Complete the six physical checks after looking at the package.
- Review the verdict, copy the summary and fix any failed check before shipping.
Frequently asked questions
Does a placarded vehicle need labels on the packages inside?
Yes. A placard replaces a label only for the containments listed in section 172.400(a): bulk packagings under 18 cubic meters other than cargo tanks, portable tanks and tank cars, portable tanks under 1,000 gallons, DOT 106 and 110 multi-unit tank car tanks; and overpacks, freight containers and unit load devices under 18 cubic meters. Non-bulk packages inside a placarded vehicle still need their labels.
What size must a hazmat label be?
Each diamond label must be at least 100 mm (3.9 in) on each side, with a solid line inner border about 5 mm inside the edge, under section 172.407(c)(1). Dimensions and features may be reduced proportionally where the package size requires it, provided the symbol and other elements stay clearly visible. The class or division number in the lower corner must be 6.3 mm to 12.7 mm high.
Do limited quantity packages need labels?
No, by highway. A limited quantity package carries the square-on-point limited quantity marking instead of hazard labels, under section 172.315, provided the gross weight does not exceed 30 kg (66 lb) and the material is eligible: Class 1, Division 2.3, Division 6.2, Class 7 and materials poisonous by inhalation are excluded. By air the package carries the Y-mark plus full labels and markings.
What is the difference between a marking and a label?
A marking is written information on the package: the proper shipping name, the identification number, the consignor or consignee, orientation arrows and special marks such as OVERPACK and RQ. A label is the diamond hazard warning with its symbol and class number. Markings live in subpart D, sections 172.300 through 172.338; labels live in subpart E, sections 172.400 through 172.450. Most packages need both.
Can labels go on the bottom of a package?
No. Section 172.406(a)(1) requires each label on a surface other than the bottom of the package. Where the package dimensions allow, the label goes on the same surface as the proper shipping name marking and near it. Primary and subsidiary labels must sit within 150 mm (6 in) of each other.
Do empty packagings still need labels and markings?
Yes, when residue remains. Section 173.29(a) requires an empty packaging with residue to be offered and transported in the same manner as when filled. Relief applies only when the packaging has been cleaned or purged, or is unused, refilled with a non-hazardous material, or holds only limited quantity or low-pressure Division 2.2 residue, with all hazmat markings, labels and placards removed, obliterated or securely covered.
Related tools
- Hazmat Placard Checker: Which placard the vehicle needs and when the threshold is met.
- Hazmat Shipping Paper Checker: Whether the shipping paper description matches the package markings.
- Hazmat Segregation Checker: Which hazard classes can ride together in one load.
Sources
- 49 CFR 172.301: General marking requirements for non-bulk packagings
- 49 CFR 172.302: Marking requirements for bulk packagings
- 49 CFR 172.304: Marking requirements
- 49 CFR 172.312: Liquid hazardous materials in non-bulk packagings
- 49 CFR 172.313: Poisonous hazardous materials
- 49 CFR 172.315: Limited quantities
- 49 CFR 172.320: Explosives
- 49 CFR 172.322: Marine pollutants
- 49 CFR 172.324: Hazardous substances in non-bulk packagings
- 49 CFR 172.400: General labeling requirements
- 49 CFR 172.400a: Exceptions from labeling
- 49 CFR 172.402: Additional labeling requirements
- 49 CFR 172.403: Radioactive material
- 49 CFR 172.406: Placement of labels
- 49 CFR 172.407: Label specifications
- 49 CFR 173.25: Authorized packagings and overpacks
- 49 CFR 173.29: Empty packagings
Regulation text verified against the live eCFR, issue date November 17, 2026. Regulation text changes. Check the current version before relying on any result.