Skip to main content

Trucking Mind

Measure the guard, not the trailer. This checker works out whether a rear impact guard is required under 49 CFR 393.86, which standard applies, plus whether the guard dimensions comply. Enter the vehicle details plus the measurements in inches. Every answer updates the result as you change each field.

The vehicle

The date decides the standard. Trailers made on or after January 26, 1998 follow paragraph (a). Older vehicles follow paragraph (b). Vehicles made in 1952 or earlier fall outside the rule.

Paragraph (a) starts at a GVWR of 10,000 lb. Find the GVWR on the certification label on the trailer.

For older vehicles only. Measure from the ground to the rear bottom edge of the body, or the chassis if the chassis is the rearmost part, with the vehicle empty. Above 30 in, a guard is required.

The guard

For older vehicles the rule asks for substantial construction plus attachment by bolts, welding, or other comparable means.

Measure the guard bottom edge from the ground. Measure the rear surface from the rearmost point of the vehicle. Enter a negative number if the guard sticks out past the rear of the vehicle. That is allowed.

Measure from each end of the horizontal member to the side extremity of the vehicle on the same side. Enter a negative number if the guard sticks out past the side.

Post-1998 trailers only. The minimum is 3.94 in across the full width of the member.

Older vehicles only, where more than one guard is fitted. Measure the largest distance between the closest points of any two guards. The limit is 24 in.

Since March 23, 2026 a missing or illegible label is no longer a violation. The label rule was rescinded. New guards sold by manufacturers still carry the label.

Pass: this guard complies.

Every dimensional check passes under section 393.86(a).

The guard meets the width, height, rear surface, plus attachment rules for this vehicle. Keep it in this condition and re-measure after any rear-end repair or suspension change.

The checks

CheckResultDetail
Guard requiredYesManufactured 2020-06-01 with a GVWR of 65,000 lb, so section 393.86(a) applies.
Guard presentPassA guard is fitted.
Securely attachedPassThe guard is securely attached, with no broken or missing fasteners and no cracked welds or parent metal.
Guard heightPassThe bottom edge is 20 in above the ground, within the 22 in limit.
Guard width, left endPassThe guard ends 2 in from the left side extremity, within the 4 in limit.
Guard width, right endPassThe guard ends 2 in from the right side extremity, within the 4 in limit.
Guard rear surfacePassThe rearmost surface is 6 in forward of the rear extremity, within the 12 in limit.
Cross-sectional vertical heightPassThe horizontal member is 4.5 in tall, above the 3.94 in minimum.
Certification labelNot a violationThe label rule in section 393.86(a)(6) was rescinded effective March 23, 2026 (FR Doc 2026-03255). A missing or illegible label is no longer citable.

The limits that apply

LimitValueNote
Standard that appliesSection 393.86(a), FMVSS 223 and 224Trailers and semitrailers, GVWR 10,000 lb or more, manufactured on or after January 26, 1998.
Guard height limit22 in maximumSection 393.86(a)(3), bottom edge above the ground.
Guard width limitWithin 4 in of each sideSection 393.86(a)(2), never beyond the side extremity.
Guard rear surface limitWithin 12 in of the rearSection 393.86(a)(4), at 22 in or more above the ground.
Vertical height minimum3.94 in minimumSection 393.86(a)(5), across the full guard width.
Annual inspectionAppendix G item 15.aAny failed check below fails the annual inspection.

What to do

  • Record the measurements in the vehicle maintenance file with the date.
  • Re-measure after any rear-end repair, suspension change, or tire size change.
  • Check the guard again before the next annual inspection.

Notes

  • A guard that passes today can fail tomorrow. Bent members, loose fasteners, plus sagging suspension move the measurements.

This tool applies 49 CFR 393.86, Appendix G item 15, plus FMVSS 223 and 224 to your inputs. Confirm the result against the regulation text plus your inspector before acting. The tool checks dimensions plus attachment. It does not test guard strength, which is a manufacturer certification matter.

Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.

Disclaimer: This tool is a compliance aid for drivers and fleets, not legal advice — confirm the result with the regulation text or your legal counsel before acting on a guard decision.

Quick answer: A trailer or semitrailer with a GVWR of 10,000 lb or more, made on or after January 26, 1998, must have a rear impact guard meeting FMVSS 223. The guard bottom edge must sit no more than 22 inches above the ground, the guard must reach within 4 inches of each side of the trailer, the rearmost surface must sit within 12 inches of the rear of the trailer. The horizontal member must be at least 3.94 inches tall. Older trucks and trailers follow a looser set of limits: 30 inches high, 18 inches from each side, 24 inches from the rear. Since March 23, 2026 a missing certification label is no longer a violation. This checker works out which standard applies to your vehicle plus whether the guard complies.

Last reviewed: · Focus keyword: rear impact guard requirements

What are the rear impact guard requirements for trailers?

A rear impact guard is the steel bar across the back of a trailer that stops a passenger car from sliding underneath in a rear-end crash. Drivers call it an underride guard or an ICC bumper. The federal rule sits in 49 CFR 393.86. It works in two paragraphs that split on the age of the vehicle. Paragraph (a) covers trailers and semitrailers with a gross vehicle weight rating of 10,000 pounds or more, manufactured on or after January 26, 1998. Those trailers need a guard that meets Federal Motor Vehicle Safety Standard No. 223, installed so the vehicle meets FMVSS No. 224. Paragraph (b) covers everything else made after December 31, 1952: older trailers plus straight trucks, buses, plus other motor vehicles. The two paragraphs set different limits, so the first question for any vehicle is always which paragraph applies.

The paragraph (a) limits are the ones most drivers meet. The bottom edge of the horizontal member must sit no more than 22 inches above the ground at any point across the full width of the member. The outermost surfaces of the horizontal member must extend to within 4 inches of the side extremities of the vehicle. They must not extend beyond either side. At any height of 22 inches or more above the ground, the rearmost surface of the horizontal member must sit within 12 inches of the rear extremity of the vehicle, although the guard may extend past the rear of the vehicle. The horizontal member must have a cross-sectional vertical height of at least 3.94 inches at any point across the guard width. Guards with rounded corners may curve upward or forward within 10 inches of the side extremities. Those five numbers are the whole of the dimensional test for a modern trailer. The checker above tests each one.

The paragraph (b) limits are looser, because they date from an era before the FMVSS standards existed. The guard bottom must sit no more than 30 inches above the ground when the vehicle is empty. The outermost surfaces must sit no more than 18 inches from each side extremity. The guard must sit no more than 24 inches forward of the rear extremity. Where more than one guard is used, the maximum lateral distance between the closest points of the guards must not exceed 24 inches. The guard must be substantially constructed plus attached by bolts, welding, or other comparable means. There is also a trigger that paragraph (a) does not have: paragraph (b) requires a guard only when the rear bottom edge of the body, or the chassis assembly if the chassis is the rearmost part, sits more than 30 inches above the ground when the vehicle is empty. A low-deck truck whose rear bottom edge sits at 28 inches needs no guard at all under paragraph (b).

Three standards work together here. Drivers mix them up. FMVSS 223 is the equipment standard: it sets the strength plus energy absorption a guard must have. It binds the guard manufacturer. FMVSS 224 is the vehicle standard: it sets where the guard must sit on a new trailer. It binds the trailer manufacturer. Section 393.86 is the in-service standard: it sets what an inspector checks on a trailer already on the road. It binds the motor carrier. A driver or fleet manager never needs to test guard strength. That job belongs to the manufacturer, whose certification stands behind the guard. The roadside plus annual inspection test is dimensions plus attachment plus condition, which is exactly what this checker measures.

Does my trailer need a rear impact guard?

Start with the vehicle type, the manufacture date, plus the GVWR. Those three facts decide the answer for most vehicles before any tape measure comes out. The table below walks through the decision in the order the regulation asks it. Work down the rows until one matches the vehicle in front of you.

VehicleRuleGuard needed?
Truck tractor, any ageSection 393.86(b)(1) excepts truck tractors. Paragraph (a) covers trailers only.No
Any vehicle made in 1952 or earlierBoth paragraphs start after December 31, 1952.No
Trailer or semitrailer, made on or after January 26, 1998, GVWR under 10,000 lbParagraph (a) starts at 10,000 lb. Paragraph (b) excepts post-1998 trailers.No
Trailer or semitrailer, made on or after January 26, 1998, GVWR 10,000 lb or moreSection 393.86(a), FMVSS 223 plus 224.Yes, unless an exception applies
Trailer made before January 26, 1998, or a truck, bus, or other vehicle made after 1952Section 393.86(b), if the rear bottom edge is more than 30 in above the ground when empty.Yes, if the trigger is met
Excepted vehicle type, any age bandSee the exceptions section below.No, while the exception applies

The most common surprise is the light trailer. A trailer made in 2015 with a GVWR of 9,500 pounds needs no guard under section 393.86, even though it looks like every other trailer on the road. Paragraph (a) never reaches it because of the weight threshold. Paragraph (b) never reaches it because it excepts trailers made on or after January 26, 1998. The checker above gives that answer in one step: enter the GVWR under 10,000 and the verdict is no guard required. The same logic catches the other side: a 1995 trailer with a GVWR of 8,000 pounds falls under paragraph (b), which has no weight threshold of its own, so it needs a guard if its rear bottom edge sits above 30 inches when empty.

The second surprise is the truck tractor. A tractor needs no rear impact guard under section 393.86 at all. Paragraph (a) covers trailers and semitrailers only. Paragraph (b)(1) names truck tractors in its exception list. The guard duty sits on the trailer, not on the power unit. A fleet that fits guards to tractors is fitting voluntary equipment, which is fine, but no inspector can cite a tractor for lacking one. Check the trailer separately, because the trailer has its own duty whatever the tractor carries.

The third surprise is the low truck. Paragraph (b) has a trigger that many drivers miss. The rule does not say every old truck needs a guard. It says a guard is needed when the rear bottom edge of the body or chassis sits more than 30 inches above the ground with the vehicle empty. A box truck with a low floor, a flatbed with a dropped deck, or a bus with a low rear overhang may sit under the trigger and need no guard. Measure the rear bottom edge first. The checker asks for that number before it asks for any guard dimension, because the answer can end the check right there.

What are the FMVSS 223 rear guard dimensions?

The dimensions in section 393.86(a) restate the FMVSS 224 installation requirements, so a driver who checks the section 393.86 numbers is checking the FMVSS numbers at the same time. The table below gives the four limits plus the rounding rule that inspectors apply. All measurements are taken with the vehicle unloaded, on level ground, with tires inflated to the manufacturer recommendation, plus air suspension, if fitted, pressurized to the manufacturer recommendation.

DimensionLimitWhere it sits in the rule
Guard height, bottom edge above the ground22 in maximum, at any point across the full widthSection 393.86(a)(3)
Guard width, each end to the side extremityWithin 4 in, never beyond the sideSection 393.86(a)(2)
Guard rear surface, forward of the rear extremityWithin 12 in, at 22 in or more above the groundSection 393.86(a)(4)
Cross-sectional vertical height of the horizontal member3.94 in minimum, across the full widthSection 393.86(a)(5)
Rounded cornersMay curve up or forward within 10 in of the side extremitiesSection 393.86(a)(3) plus (a)(4)

Height is the measurement that fails most often. It fails for reasons that have nothing to do with the guard. A trailer with sagging suspension sits lower at the rear, which helps height but hurts nothing else. A trailer with new, taller tires sits higher, which can push a guard that passed last year over the 22-inch limit. A trailer measured on a slope gives a false reading either way. Always measure on level ground, unloaded, with the tires at the recommended pressure. If the guard sits at 22 inches exactly, it passes: the rule says the distance shall not exceed 22 inches, so the limit itself is compliant.

Width fails quietly. A guard that was the right width when the trailer was built can end up short after a body repair narrows it, or after a replacement guard is fitted that was made for a narrower trailer. Measure both ends. A guard can pass on the left and fail on the right if it was fitted off center. The rule also bars the guard from extending beyond either side extremity, so a guard that sticks out past the side of the trailer fails just as surely as one that falls short. Enter a negative number in the checker if the guard sticks out. The checker flags it.

The rear surface measurement has a subtlety worth knowing. The 12-inch limit applies at heights of 22 inches or more above the ground. Below that height, the rule does not set a rear surface limit, because the low part of the guard is already governed by the height rule. In practice the horizontal member sits in the band the rule covers, so measure the rearmost surface of the member against the rear extremity of the vehicle. The rear extremity is the rearmost point of the vehicle above 22 inches and below 75 inches, with the doors or tailgate in their normal running position. Nonstructural protrusions such as taillamps, rubber bumpers, hinges, plus latches do not count. A boat tail or folding aerodynamic device does not count as the rear extremity if it folds away, per the FMVSS 224 definition.

The vertical height minimum of 3.94 inches is the dimension drivers least expect. It is a metric figure, 100 millimeters, converted to inches. A guard built from a 4-inch member passes with room to spare. A guard built from a 3-inch member fails, whatever its height and width. The annual inspection standard in Appendix G item 15.a(6) rounds the same figure up to 4 inches in its text, while section 393.86(a)(5) says 3.94 inches. The checker uses 3.94 inches, the figure in the rule itself. A member measuring 3.95 inches passes under the rule, even though it falls short of the rounded figure in the inspection appendix.

What are the rules for older trucks and trailers?

Paragraph (b) of section 393.86 is the older rule. It still governs a large part of the fleet: every straight truck, bus, plus other motor vehicle made after 1952, plus every trailer made before January 26, 1998. The limits are wider than the paragraph (a) limits. The rule has no weight threshold, no FMVSS certification duty, plus no vertical height minimum. The table below gives the paragraph (b) limits side by side with the paragraph (a) limits so the difference is easy to see.

DimensionParagraph (b), older vehiclesParagraph (a), post-1998 trailers
Guard height30 in maximum, vehicle empty22 in maximum
Guard width, each end to the sideWithin 18 inWithin 4 in, never beyond the side
Guard rear surfaceWithin 24 in forward of the rear extremityWithin 12 in forward of the rear extremity
Vertical height of the memberNo minimum in the rule3.94 in minimum
Lateral gap between guards24 in maximum, where more than one guard is usedSingle horizontal member, no gap rule
AttachmentSubstantially constructed, bolts, welding, or comparable meansSecurely attached per FMVSS 224 installation

The trigger matters more than the limits for older vehicles. Paragraph (b)(1) requires a guard only when the rear bottom edge of the body, or the chassis assembly if the chassis is the rearmost part, sits more than 30 inches above the ground when the vehicle is empty. Many older straight trucks sit under that line. A delivery truck with a low cargo floor, a beverage truck with a dropped frame, or a small bus may need no guard at all. The checker asks for the rear bottom edge height first for exactly this reason. Enter 30 inches or less and the verdict is no guard required, with no guard dimensions needed.

Paragraph (b) also has a compliance route that paragraph (a) does not. Section 393.86(b)(3) says a low chassis vehicle, special purpose vehicle, or wheels back vehicle is treated as compliant when the body, chassis, or other parts of the vehicle provide rear end protection comparable to a guard meeting paragraph (b)(1). The vehicle itself is the guard. A low chassis truck whose frame rails run low and wide at the rear, or a wheels back vehicle whose rear axle sits close to the back of the body, may satisfy the rule with no separate guard fitted. The checker asks whether the structure provides that comparable protection. It treats a yes answer as compliant. If the answer is unsure, the checker treats the vehicle as needing a guard and says so in the notes, because an unconfirmed claim of comparable protection is not a defense at roadside.

One paragraph (b) rule has no matching annual inspection item. The gap is worth knowing. Section 393.86(b)(1)(ii) limits the lateral distance between guards to 24 inches where more than one guard is used. Appendix G item 15.b, the annual inspection standard, lists five reject items for older vehicles and does not include the lateral gap. A pair of guards 30 inches apart violates section 393.86 and can draw a roadside citation, but the same gap is not listed as a reason to fail the annual inspection. The checker tests the gap anyway, because the rule is the rule. It notes the inspection gap in the limits table so the result is not a surprise.

Older vehicles also carry a trap around modifications. A truck that left the factory under the 30-inch trigger can cross it later: taller tires, a suspension lift, a new body with a higher floor, or a frame stretch can all raise the rear bottom edge above 30 inches. The day the trigger is crossed, the guard duty arrives, even though nothing about the guard changed. Any modification that raises the rear of an older vehicle should end with a fresh measurement of the rear bottom edge plus a run through this checker.

Which vehicles are exempt from the rear impact guard rule?

Seven vehicle types are excepted from paragraph (a). Five of them are also excepted from paragraph (b). The exceptions exist because a standard guard cannot be fitted to these vehicles, or because the vehicle shape already does the job. The table below gives each exception, the definition behind it, plus which paragraph it escapes. The definitions come from sections 390.5 plus 393.5. The checker applies them as written.

Excepted vehicleWhat it isExcepted from
Pole trailerA trailer that carries logs or poles lengthwise, with the load forming the body of the vehicle.Paragraphs (a) plus (b)
Pulpwood trailerA trailer designed exclusively for harvesting logs or pulpwood, with a skeletal frame plus no means to attach a solid bed, body, or container.Paragraphs (a) plus (b)
Low chassis vehicleA vehicle whose chassis extends behind the rearmost tires with a lower rear surface that meets the guard configuration requirements.Paragraph (a). Under paragraph (b), compliant by comparable protection, not excepted.
Special purpose vehicleA vehicle with work-performing equipment that sits in or moves through the space the guard would occupy while the vehicle is in transit.Paragraph (a). Under paragraph (b), compliant by comparable protection, not excepted.
Wheels back vehicleA vehicle whose rearmost axle is permanently fixed with the rear tire surface no more than 12 in forward of the rear extremity (post-1998) or 24 in (older).Paragraph (a). Under paragraph (b), compliant by comparable protection, not excepted.
Road construction controlled horizontal discharge trailerA trailer with a mechanical drive plus a conveyor that delivers asphalt plus road building materials into paving equipment.Paragraphs (a) plus (b)
Driveaway-towaway operationA vehicle towed in an operation where the vehicle itself is the cargo being delivered.Paragraphs (a) plus (b)

Three of the seven are not true exceptions under paragraph (b). The distinction matters. Low chassis, special purpose, plus wheels back vehicles are excepted from paragraph (a) outright. Under paragraph (b) they are not excepted. Instead, section 393.86(b)(3) treats them as compliant when the body, chassis, or other parts provide comparable rear end protection. The difference is real: an excepted vehicle needs nothing, while a comparable-protection vehicle needs the structure that does the protecting. A special purpose truck whose work equipment is removed loses its comparable protection and gains a guard duty. The checker handles the two cases separately, which is why it asks the comparable-protection question only for older vehicles with one of those three types.

The road construction controlled horizontal discharge trailer is the exception drivers most often miss, because the name is long and the vehicle is rare. It is a trailer built to feed asphalt into a paving machine through a conveyor. The conveyor occupies the space where a guard would sit. Both paragraphs except it. The research behind this tool originally listed six exceptions and missed this one; the live text of section 393.86(a)(1) names it plainly. The checker includes it.

Exceptions follow the vehicle, not the load. A pole trailer carrying a load of lumber instead of logs is still a pole trailer if it meets the definition. A trailer that stops being a pulpwood trailer because a solid bed is fitted stops being excepted at the same moment. Keep a note of the exception in the vehicle file, with the definition it rests on, so an inspector who questions the missing guard can follow the reasoning. If the vehicle is rebuilt or repurposed, run the checker again: losing the exception brings the guard duty back at once.

Do I still need the certification label on the guard?

No. The rule that required a certification label on an in-service guard was rescinded effective March 23, 2026. Before that date, section 393.86(a)(6) required each rear impact guard used to satisfy paragraph (a) to be permanently marked or labeled as required by FMVSS 223 S5.3. The label carried the guard manufacturer name plus address, the month plus year of guard manufacture, plus the letters DOT as the manufacturer certification that the guard met the standard. Labels wore off, faded, or were painted over during the service life of a trailer. Carriers were cited for a missing label on a guard that was otherwise sound. FMCSA removed the requirement in a final rule published February 19, 2026 (FR Doc 2026-03255, 91 FR 7874, Docket FMCSA-2025-0107), effective March 23, 2026. Paragraph (a)(6) now reads [Reserved]. A missing or illegible label is no longer citable. The checker treats it as not a violation.

One nuance matters. It is easy to get wrong. The rescission removed the carrier-side duty in the Federal Motor Carrier Safety Regulations. It did not remove the manufacturer-side duty in FMVSS 223. Section S5.3 of FMVSS 223 still requires each guard to be permanently labeled with the manufacturer name plus address, the manufacture month plus year, plus the DOT certification letters, in letters at least 2.5 millimeters high, on the forward or rearward facing surface of the horizontal member. A new guard bought today still carries that label, because the guard manufacturer must fit it. The change is about who gets cited: an inspector can no longer write a violation against a motor carrier because the label on an in-service guard has worn away. The guard itself still has to meet FMVSS 223. Only the label evidence rule went away.

The rescission also removed the FMCSA guidance document that covered illegible, incomplete, or missing rear impact guard certification labels. Before the rescission, CVSA had already told inspectors not to cite a missing label, on the reasoning that the label duty belonged to the manufacturer rather than the end user. The 2026 rule made that practice part of the regulation. If a carrier was cited for a missing label before March 23, 2026, the citation stands on the rule as it was then. Citations after that date for a missing label alone should be challenged through DataQs, because the paragraph they rest on no longer exists.

Do not read the rescission as a reason to ignore the guard. Every structural plus dimensional rule in section 393.86(a) survived unchanged: the 22-inch height, the 4-inch width, the 12-inch rear surface, plus the 3.94-inch member height all still apply. A guard that fails any of them still fails the annual inspection. The label was paperwork. The steel still matters.

What changed in the 2022 FMVSS 223 upgrade?

NHTSA upgraded FMVSS 223 plus 224 in a final rule published July 15, 2022 (87 FR 42339, FR Doc 2022-14330), under a mandate in the November 2021 Bipartisan Infrastructure Law. The rule took effect January 11, 2023, with a compliance date of July 15, 2024 for guards manufactured on or after that date. Optional early compliance was allowed. The upgrade adopted requirements similar to the Canadian standard, CMVSS 223, so the two countries now ask for guards of similar strength.

The upgrade changed strength, not dimensions. The old standard required a guard to resist a uniform distributed load of 100,000 newtons. The new standard requires 350,000 newtons across the horizontal member, plus 50,000-newton point loads at two test locations, with deflection limited to 125 millimeters and no load path eliminated. The guard must also absorb at least 20,000 joules of energy by plastic deformation within the first 125 millimeters of deflection, unless it resists a load over 700,000 newtons, in which case the energy absorption test does not apply. After the load is applied, the ground clearance at each support must not exceed 560 millimeters. Those are laboratory tests on a guard specimen, run by the manufacturer, not measurements a driver can take with a tape measure.

The 35 mph figure that appears in coverage of the rule is the crash scenario the standard is designed for, not a test the regulation runs. The upgraded guard is designed to protect occupants of compact plus subcompact passenger cars striking the rear of a trailer at 35 mph, in two configurations: a centered impact where the full width of the car overlaps the trailer, plus an offset impact where 50 percent of the car width overlaps the trailer. The compliance tests are quasi-static force tests, which push on the guard slowly with a steel block rather than crashing a car into it. The force levels were set so a guard that passes them performs in the 35 mph scenarios. Saying the guard passed a 35 mph crash test overstates what the regulation requires. This page states the position plainly.

The upgrade did not change the dimensions in section 393.86. It imposed no retrofit duty on trailers already in service. A trailer built in 2019 keeps the guard it was built with, judged against the standard in effect at the time of manufacture. A replacement guard bought today meets the stronger standard, because guards manufactured on or after July 15, 2024 must comply with it. A fleet buying replacement guards gets stronger guards without asking. A fleet keeping old guards is not in violation for the age of the guard alone, as long as the dimensions plus attachment still comply.

One more 2022 change is worth noting for cargo tank operators. FMVSS 224 S3 says that if a cargo tank motor vehicle certified to carry hazardous materials has a rear bumper or rear end protection device conforming with 49 CFR part 178 in the area of the horizontal member, the guard need not meet the energy absorption requirement in FMVSS 223 S5.2.2. The strength requirements still apply. The carve-out recognizes that the part 178 device already provides rear protection on a tank vehicle.

Will a bad guard put my truck out of service?

No, not for the guard alone. CVSA has no out-of-service criterion for rear impact guards. An inspector who finds a missing, damaged, or noncompliant guard cites a violation and lets the vehicle continue, rather than placing it out of service until the guard is fixed. CVSA said so publicly during its 2019 enforcement focus on rear guards, when its roadside inspection director confirmed that carriers with guard violations would not be placed out of service, although they would not receive a CVSA decal while the violation stood. Lawmakers asked CVSA to add guards to the out-of-service criteria. CVSA declined, saying it was not convinced the criteria were needed for guards. That position still stands. A guard violation is a citation, not a shutdown.

The citation still costs. A section 393.86 violation carries a severity weight of 2 in the Vehicle Maintenance BASIC of the FMCSA Safety Measurement System, under violation codes 393.86A1-RIG for post-1998 trailers plus 393.86B1-RIG for older vehicles. Two points is a low weight next to brake or tire violations, but it is not zero. It lands on the same BASIC that carries the violations that do put vehicles out of service. Repeated guard violations across a fleet add up in the same measure as any other maintenance defect. The FMCSA Fine Calculator shows what enforcement penalties look like when violations reach the penalty stage, although a single guard citation at roadside is normally a state fine rather than a federal penalty case.

The annual inspection is where a bad guard bites hardest. Appendix G to Subchapter B, the minimum periodic inspection standards that eCFR presents as Appendix A to Part 396, lists rear impact guards as item 15. A vehicle does not pass its annual inspection if the guard is missing, if the guard is not securely attached, or if any dimension fails. The inspector checks the guard against the same limits this checker tests. A trailer that fails item 15 cannot pass its annual inspection until the guard is repaired or replaced. Operating a vehicle past its inspection date brings its own violations. The Annual Inspection Due-Date Tracker works out when the next inspection falls due, so a guard repair can be scheduled before the date arrives rather than after it passes.

A guard defect also belongs on the driver vehicle inspection report, even though the guard is not one of the eleven parts listed in section 396.11. The eleven listed parts are brakes, parking brake, steering, lighting, tires, horn, wipers, mirrors, coupling devices, wheels plus rims, plus emergency equipment. The guard is not among them. But section 396.11(a)(2)(i) also requires the driver to report any defect or deficiency discovered by or reported to the driver that would affect the safety of operation of the vehicle. A bent, loose, or missing guard affects safety, so it goes on the report. The DVIR Checker works through the report duties. The Pre-Trip Inspection Checklist covers the walk-around that finds a damaged guard before the truck leaves the yard.

One more consequence is easy to overlook. A vehicle with a guard violation does not receive a CVSA decal. A vehicle without a decal is more likely to be inspected again at the next scale. A missing decal is not a violation by itself, but it removes the signal that tells the next inspector this vehicle recently passed a full inspection. Fixing the guard promptly restores the decal at the next clean inspection, which is one more reason to treat a guard citation as a repair order rather than a fine to pay and forget.

How do you measure a rear impact guard?

Measure on level ground, with the vehicle unloaded, the fuel tanks full, plus the tires inflated to the manufacturer recommendation. Air suspension, if fitted, should be pressurized to the manufacturer recommendation. Those are the conditions FMVSS 224 S5.1 sets for the installation check. They are the conditions an inspector uses. Measuring a loaded trailer, or a trailer parked on a slope, gives numbers that do not match the rule and can turn a pass into a fail or the reverse.

Start with the rear extremity, because two of the four measurements hang from it. The rear extremity is the rearmost point of the vehicle above 22 inches and below 75 inches from the ground, with the cargo doors, tailgate, or other permanent structures in their normal running position. Taillamps, rubber bumpers, hinges, plus latches do not count. On a dry van the rear extremity is usually the rear face of the doors. On a flatbed it is the rear face of the deck. On a trailer with a folding aerodynamic device, the device does not count if it folds to within 12 inches of the guard. Stand a straight edge or a plumb line at that rearmost point and measure forward to the guard.

Measure the height first. Run a tape measure from the ground to the bottom edge of the horizontal member, at several points across the width. Take the largest reading. The rule sets the limit at any point across the full width, so one high spot fails the guard even if the rest of it sits low. Guards with rounded corners may curve upward within 10 inches of the side extremities, so measure the straight portion of the member and note the corner curve separately. If the largest reading is 22 inches or less on a post-1998 trailer, the height passes. On an older vehicle the limit is 30 inches, measured with the vehicle empty.

Measure the width next. Measure from each end of the horizontal member to the side extremity of the vehicle on the same side. The side extremity is the outermost point of the side of the vehicle, measured in the same height band as the rear extremity. A guard that ends 3 inches from the left side and 5 inches from the right side fails on the right, whatever the left side shows. Measure both ends and enter both numbers in the checker. If the guard sticks out past the side, enter a negative number: the checker treats that as a failure under paragraph (a), which bars the guard from extending beyond either side.

Measure the rear surface and the member height last. For the rear surface, measure from the rearmost surface of the horizontal member forward to the rear extremity plane, at a height of 22 inches or more above the ground. The limit is 12 inches on a post-1998 trailer and 24 inches on an older vehicle. For the member height, measure the vertical height of the horizontal member itself, not the height above the ground. The minimum is 3.94 inches on a post-1998 trailer. A tape measure plus a straight edge is enough for all four measurements. No special tool is needed. The whole check takes five minutes once the routine is familiar.

Record the numbers. Write the four measurements plus the date in the vehicle maintenance file, next to the annual inspection record. A file that shows the guard measured 20 inches high plus 2 inches from each side at the last inspection is useful evidence if an inspector questions the guard later. It makes the next measurement faster because the baseline is already there. The checker copy button produces a summary with the verdict plus the checks, ready to paste into the file.

Do I need side underride guards too?

No federal rule requires side underride guards as of November 2026. The rear guard rule in section 393.86 covers the rear of the vehicle only. No paragraph of the Federal Motor Carrier Safety Regulations requires a guard along the side of a trailer. No FMVSS sets a side guard standard for new trailers. A carrier that fits side guards is fitting voluntary equipment, which is allowed, but no inspector can cite a trailer for lacking them.

The position may change. The history is worth knowing. NHTSA published an advance notice of proposed rulemaking on side underride guards on April 21, 2023 (88 FR 24535, Docket NHTSA-2023-0012), asking for comment on whether to require them. The action remains at the prerule stage in the Unified Agenda. NHTSA has stated that it has no schedule to complete the action. Congress has considered bills that would require side guards, including the Stop Underrides Act, but no bill has become law. Until a final rule publishes with a compliance date, side guards stay voluntary.

Side guards do exist in the market. Some fleets fit them for safety or for fuel economy, because a side skirt that closes the gap under a trailer also cuts aerodynamic drag. A side skirt is not a side underride guard unless it is built to the strength a guard needs. Most skirts are built for airflow rather than impact. A fleet that wants side protection should buy a device tested for underride performance, not assume a fuel-saving skirt does the job. The distinction matters in a crash, where a thin skirt folds and a real guard holds.

This checker covers the rear guard only, because the rear guard is the one the law regulates. If a side guard rule ever publishes, the checker will be updated at the next review. The review date for this page is about May 18, 2027. The side guard position is on the list of items to re-check then, along with the FMVSS 224 misprint noted in the sources.

How do you use the Rear Impact Guard Checker?

Work through the fields in order. The tool updates with every change, so you can fix an answer and watch the verdict change.

  1. Choose the vehicle type and enter the manufacture date plus the GVWR.
  2. Pick the exception that applies, or none.
  3. Say whether a guard is fitted and whether it is securely attached.
  4. Enter the guard measurements in inches.
  5. Read the verdict, the checks, plus the limits table.
  6. Copy the summary for the vehicle maintenance file.

Use the tool at the vehicle, with a tape measure in hand. The measurements it asks for are the ones an inspector takes, in the same order an inspector takes them. Entering the numbers as you measure them gives a verdict you can act on at once. Entering them later from memory gives a verdict only as good as the memory. A guard dimension misremembered by an inch can flip a pass to a fail.

Copy the summary before the vehicle leaves. The copy includes the verdict, the checks, the actions, plus the notes, which is the skeleton of a maintenance file entry. Paste it into the file with the date plus the vehicle unit number. If a check fails, the summary says which one and by how much, which is what the shop needs to fix it. If the vehicle is exempt, the summary names the exception, which is what the next inspector needs to see.

Questions drivers ask

What is the maximum height for a rear impact guard?

On a trailer or semitrailer manufactured on or after January 26, 1998, the bottom edge of the horizontal member must sit no more than 22 inches above the ground at any point across the full width, per 49 CFR 393.86(a)(3). On an older truck or trailer, the limit is 30 inches above the ground with the vehicle empty, per section 393.86(b)(1)(i). Measure on level ground, unloaded, with tires inflated to the manufacturer recommendation.

How wide must a rear impact guard be?

On a post-1998 trailer, the outermost surfaces of the horizontal member must extend to within 4 inches of the side extremities of the vehicle. They must not extend beyond either side, per 49 CFR 393.86(a)(2). On an older vehicle, the limit is 18 inches from each side extremity, per section 393.86(b)(1)(iii). Measure both ends: a guard can pass on one side and fail on the other.

Do I need a certification label on my rear impact guard?

No. The label rule in 49 CFR 393.86(a)(6) was rescinded effective March 23, 2026 (FR Doc 2026-03255). A missing or illegible label on an in-service guard is no longer citable. New guards sold by manufacturers still carry the FMVSS 223 S5.3 label, because that duty binds the manufacturer, not the carrier. The structural and dimensional rules are unchanged.

What happens if my trailer has no rear impact guard?

A missing guard is a violation of 49 CFR 393.86, it fails the annual inspection under Appendix G item 15. It carries a severity weight of 2 in the Vehicle Maintenance BASIC. It is not an out-of-service condition: CVSA has no out-of-service criterion for rear impact guards, so the vehicle is cited rather than shut down. The vehicle also does not receive a CVSA decal while the violation stands.

Are pole trailers exempt from the rear impact guard rule?

Yes. Pole trailers are excepted from both paragraphs of 49 CFR 393.86. Pulpwood trailers, road construction controlled horizontal discharge trailers, plus trailers towed in driveaway-towaway operations are also excepted from both paragraphs. Low chassis vehicles, special purpose vehicles, plus wheels back vehicles are excepted from paragraph (a); under paragraph (b) they comply when the body or chassis provides comparable rear end protection.

Do I need side underride guards on my trailer?

No federal rule requires side underride guards as of November 2026. Section 393.86 covers the rear of the vehicle only. NHTSA published an advance notice of proposed rulemaking on side guards in April 2023 (88 FR 24535), but the action remains at the prerule stage with no schedule to complete it. Side guards fitted today are voluntary equipment.

Related tools

  • Annual Inspection Due-Date Tracker: work out when the next annual inspection falls due, so a guard repair can be scheduled before the date arrives.
  • Tire Compliance Checker: check tread depth, load ratings, plus pressure against 49 CFR 393.75 before the same inspection.
  • DVIR Checker: work through the driver vehicle inspection report duties, including defects that belong on the report even when they are not on the eleven-item list.

Sources

Follow on WhatsApp Ask by Voice