Choose your trailer size, then enter your pallets, cargo cube and tare weights. Add your scale weights for the axle and bridge checks, plus your miles and costs for the cost per mile.
Your trailer
52 ft 6 in inside, 3,900 cu ft, 26 pallets straight or 30 turned.
Pallet count is checked against the straight count for your size. Leave the cube box blank to skip the cube check.
Your scale weights (optional)
Scale every axle group before you roll. Leave the boxes blank to check gross weight only.
Axle spacings
Defaults suit a standard dry van rig with a day cab tractor. Measure your own rig for an exact bridge check.
Cost per mile (optional)
Rate, diesel price and every cost figure are your numbers: the tool carries no rate, diesel or cost figure of its own. Annual miles defaults to 100,000 as a starting point: change it to your own miles.
Enter your load to see the fit.
Cube binds first on light freight
Light, bulky freight fills the trailer before it reaches the payload limit. Enter your cargo cube to see whether cube or weight binds first on your load.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not professional advice — verify figures from official sources before acting on them. Scale every axle group before you roll: a legal gross weight can hide an overweight group.
Quick answer: Enter your trailer size, pallets and cargo cube to see whether cube or weight binds first, plus your cost per mile from your own costs. The example loads 26 pallets at 1,500 lb each: 39,000 lb of cargo, 3,500 cu ft of 3,900 cu ft, gross weight 71,000 lb with 9,000 lb to spare.
How cube and weight bind first
A dry van fills up in two ways: by weight and by cube. Whichever limit you reach first is the one that binds. The tool tells you which one it is.
The example loads 26 pallets at 1,500 lb each, for 39,000 lb of cargo in a 53 ft van. The cargo takes 3,500 cu ft of the 3,900 cu ft capacity, or 89.7 percent, against 81.3 percent of the 48,000 lb payload. Cube binds first here, with 400 cu ft to spare.
With a 14,000 lb trailer and an 18,000 lb tractor, the rig grosses 71,000 lb, leaving 9,000 lb under the 80,000 lb limit. The 39,000 lb load is 3,000 lb under the typical 42,000 lb payload for a 53 ft dry van.
Light freight cubes out first: paper goods, furniture and insulation fill the trailer long before the weight limit bites. Heavy freight weighs out first: steel, tile and bottled water reach the payload limit with cube to spare. Enter your own cube to see which limit binds on your load.
Dry van sizes
The 53 ft dry van is the standard trailer in the United States: dry vans are 61 percent of US trailer production and carry about 70 percent of freight. The 48 ft van suits shorter hauls and tighter docks. The 28 ft pup runs in doubles.
The table below lists the three sizes with verified inside dimensions, cube, pallet counts and payload.
| Size | Inside L x W x H | Cube (cu ft) | Pallets | Tare (lb) | Max cargo (lb) |
|---|---|---|---|---|---|
| 53 ft dry van | 52 ft 6 in x 100 in x 110 in | 3,900 | 26 (30) | 14,000 | 48,000 |
| 48 ft dry van | 47 ft 6 in x 100 in x 110 in | 3,500 | 24 (28) | 13,000 | 48,000 |
| 28 ft pup | 27 ft 3 in x 98 in x 108 in | 2,000 | 14 | 8,000 | 22,000 |
Source: Wabash, Utility and Hyundai maker specs for the 53 ft van; Hale and repackify for the 48 ft van; Palmer Leasing, Reddaway and Stream for the 28 ft pup. Figures checked 17 Nov 2026.
Inside width runs 98 to 101 in and inside height 108 to 110 in by maker, so the table uses the common figures. A 48 ft van holds 24 pallets straight when the inside length reaches 48 ft; a 47 ft 6 in box holds 22. Turned pallets fit more but load slower, so the tool checks the straight count.
Tare weights vary by maker and spec: a 53 ft van tares 13,350 to 15,350 lb, a 48 ft van 12,500 to 14,000 lb and a pup about 8,000 lb. The tool defaults to 14,000 lb, 13,000 lb and 8,000 lb. Change the tare to match your own trailer.
Axle groups and the bridge formula
Gross weight is only half the check. Each axle group has its own limit: 20,000 lb for a single axle and 34,000 lb for a tandem under 23 CFR 658.17.
The bridge formula then caps groups of axles by their spacing. W equals 500 times the bracket of L times N over N minus 1, plus 12N, plus 36.
W is the weight in pounds. L is the distance in feet between the first and last axle of the group. N is the number of axles in the group.
The example scale ticket reads steer 11,500 lb, drives 31,000 lb and trailer tandem 28,500 lb. The three groups add to 71,000 lb, matching the gross weight.
Drives plus trailer tandem total 59,500 lb against a 68,000 lb bridge limit over 48 ft. The whole rig at 59 ft with 5 axles is capped by the 80,000 lb gross limit.
The tool checks the steer axle against a 12,000 lb practical ceiling from tire and axle ratings. Federal law allows 20,000 lb on the steer axle, but most steer tires and axles are rated well below that. Two consecutive tandems may each carry 34,000 lb when the first to last axle distance is 36 ft or more.

A pup rig can fail the bridge check where a 53 ft rig passes. With the trailer tandem 24 ft behind the drives, the drives plus trailer group spans 32 ft and is capped at 63,500 lb, while the whole rig is capped at 75,000 lb. The tool runs both checks on every size.
The Bridge Formula Axle Weight Checker linked below runs the same formula on any axle group with your own spacings.
Length and width: the federal floor
Federal law sets a floor, not a ceiling, on trailer length. Under 23 CFR 658.13 no state may bar a semitrailer of 48 ft or less from the National Network. The 53 ft trailer runs on state law and grandfathering, not on a federal 53 ft rule.

No state may set an overall length limit on a tractor semitrailer combination under 23 CFR 658.13(b)(3). States may still enforce the kingpin to rear axle limits they had on 1 December 1982. California caps the kingpin to rear axle distance at 40 ft for a trailer with two or more axles.
The federal width limit is 102 in on the National Network under 23 CFR 658.15. A standard dry van is 102 in wide outside, with 98 to 101 in inside. Hawaii allows 108 in.

The tool defaults the drive to trailer distance to 40 ft on a 53 ft van, which keeps the kingpin to rear axle distance near the 40 ft California limit. Slide the tandems forward for a shorter state, or back where the state allows more. Measure your own rig for an exact bridge check.
License: Class A, no endorsement
Dry van work needs a Class A CDL. A combination vehicle with a gross combination weight rating of 26,001 lb or more, with the towed unit over 10,000 lb, is a Group A vehicle under 49 CFR 383.91(a)(1). A loaded dry van rig clears both numbers.

A standard dry van needs no endorsement. The endorsement list in 49 CFR 383.93(b) covers double and triple trailers, passenger vehicles, tank vehicles, hazardous materials and school buses: a dry van is none of those. A hazmat load in a dry van still needs the H endorsement.

A tank of 1,000 gallons or more inside a dry van still needs the N endorsement. Endorsements follow the load, not the trailer.
What the cost per mile covers
Enter your diesel price and MPG, your annual insurance premium, your maintenance cost per mile and your fixed costs to see the full cost per mile. The tool adds the four parts you enter and shows the all-in figure. Every money input is your number: the tool carries no rate, diesel or cost figure of its own.
As an example only, take 600 loaded miles plus 80 deadhead miles at a $3.25 rate, $4.75 diesel and 7.0 MPG. Fuel costs $0.68 a mile.
Add $12,000 insurance a year, $0.20 maintenance a mile and fixed costs of $2,500 truck plus $800 trailer a month and $1,500 permits a year. Insurance adds $0.12 a mile, maintenance $0.20 and fixed costs $0.41, for $1.41 all-in.
The run breaks even at $1.60 a loaded mile and nets $991.49 after a $958.51 total cost. Gross revenue is $1,950.00, net per loaded mile is $1.65 and net per total mile is $1.46, with deadhead at 11.8 percent of miles.
Deadhead is the silent cost: the average truck ran 16.5 percent of its non-tank miles empty in 2025, according to ATRI. Every empty mile burns fuel and time with no revenue, so the break even rate climbs as deadhead grows. Enter your own deadhead miles to see what empty running costs you.
How to use this calculator
Six steps and one result. No account and no email needed.
- Choose your trailer size: 53 ft, 48 ft or 28 ft pup.
- Enter your pallets, weight per pallet, cargo cube and tare weights.
- Enter your scale weights for the steer axle and both tandems.
- Check the spacings against your own rig, or keep the standard defaults.
- Read the verdict: the load fit, the axle checks and the bridge checks.
- Enter your miles, rate and costs to see your cost per mile and net.
Dry van calculator questions
How many pallets fit in a 53 ft dry van?
A 53 ft dry van holds 26 standard 48 by 40 in pallets loaded straight, in two rows of 13. Pinwheeling fits 28 pallets and turning them sideways fits 30, but turned pallets are harder to unload at a dock. The tool checks your pallet count against the straight count for the size you choose.
What binds first, cube or weight?
It depends on the freight. Light, bulky freight fills the cube before it reaches the payload limit, so cube binds first. Heavy, dense freight reaches the payload limit with cube to spare, so weight binds first.
Do I need an endorsement to pull a dry van?
No. A standard dry van needs no endorsement: the endorsement list in 49 CFR 383.93 covers double and triple trailers, passenger vehicles, tank vehicles, hazardous materials and school buses only. You still need a Class A CDL, since a loaded dry van rig clears the 26,001 lb combination threshold in 49 CFR 383.91.
What is a good cost per mile for a dry van?
There is no single good number: your cost per mile depends on your truck payment, your insurance, your fuel economy and your miles. The tool adds your four cost parts, so the figure it shows is your cost, not a market average. Compare your all-in cost per mile against the break even rate it shows for each run.
Can a 53 ft trailer run in every state?
A 53 ft semitrailer runs on the National Network in every state, but the federal floor is 48 ft, so 53 ft runs rest on state law and grandfathering. Some states cap the kingpin to rear axle distance: California allows 40 ft with two or more axles. Check the state rules on your route before you roll.
Why does the tool ask for my scale weights?
Cargo weights alone cannot tell you what each axle carries. The tool checks each axle group and the bridge formula from the scale weights you enter. Weigh every group before you trust a legal gross weight.
Related tools and guides
- Tanker Load Calculator: work out tanker load weight, axle weights and the most you can legally load
- Step Deck Fit Calculator: check freight fit on both step deck levels plus payload
- Doubles Calculator: split pup weight, check axle groups and the bridge formula
- Bridge Formula Axle Weight Checker: check any axle group against the bridge formula with your own spacings
- Cost Per Mile Calculator: put maintenance and repair costs beside fuel and insurance in your full cost per mile
- All Trucking Mind tools: free calculators and checkers for drivers and carriers
This calculator follows the weight limits in 23 CFR 658.17, the length and width rules in 23 CFR 658.13 and 658.15 and the license rules in 49 CFR 383.91 and 383.93. It is guidance only.
Weight limits and size rules change. Confirm your figures with the current rule text before you rely on a single number.
Your inputs stay in your browser. Nothing is sent to our servers.