Enter your freight size and weight, then check the deck sizes against your own trailer. The result shows which deck fits, the binding limit, the gross weight check and the rate math.
Your freight
Measure the tallest point of the freight, including any pallet, crate or frame it sits on.
Your trailer
Defaults suit a standard 48 to 53 ft step deck. Change any box to match your own trailer.
162 inches is 13 ft 6 in, the common state limit. Some states allow 168 inches: set your own limit for your route.
Tare weights (optional)
Leave both blank to skip the gross weight check.
Rate (optional)
Rate and diesel price are your numbers: the tool carries no rate or fuel figure of its own.
Enter your freight to see if it fits.
Measure your own trailer
Deck heights vary by maker, by model and by load. Measure your own trailer before you book a tall load: a 2 inch difference can turn a legal load into an overheight one.
Your inputs stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not professional advice — verify figures from official sources before acting on them. Deck heights vary by maker and by load, so measure your own trailer before you book a tall load.
Quick answer: Enter your freight size and weight to see if it fits the upper deck, the lower deck, both or neither. The example loads a 32 ft machine, 96 in wide and 108 in high at 38,000 lb: it fits the lower deck only, with 15 inches to spare, while the upper deck fails on height by 6 inches.
How the fit check works
The tool checks your freight against both decks of a standard step deck. It checks length, height, width and weight on each deck, then names the limit that binds first.
Take a 32 ft machine, 96 in wide and 108 in high at 38,000 lb. On the lower deck it stands 147 in tall against a 162 in limit, with 15 inches of height and 96 inches of length to spare. On the upper deck it stands 168 in tall, so it fails on height by 6 inches.
Deck sizes vary by maker, so every deck box on the tool takes your own numbers. Measure your trailer before you trust a standard figure: a 2 inch difference can turn a legal load into an overheight one.
| Deck | Length | Height | Max freight height |
|---|---|---|---|
| Upper | 11 ft | 60 in | 102 in |
| Lower | 40 ft | 39 in | 123 in |
The table shows the standard defaults. A 48 ft trailer usually runs a 38 ft lower deck, while a 53 ft trailer runs 40 to 42 ft below.
The height rule: there is no federal limit
There is no federal height limit for trucks. The Federal Highway Administration says plainly that no federal vehicle height limit is imposed, so each state sets its own.
State limits run from 13 ft 6 in to 14 ft 6 in. Ohio caps vehicle height at thirteen feet six inches under Ohio Revised Code 5577.05, while some western states allow more.
The tool defaults to 162 inches, which is 13 ft 6 in, the common state limit. Raise it to 168 inches when your whole route allows 14 ft. Check every state on the route before you roll.
The width rule: 102 inches
Width is a federal rule, unlike height. Under 23 CFR 658.15 no state may set a width limit of more or less than 102 inches on the National Network, except Hawaii at 108 inches.
The tool checks your freight width against 102 inches. Freight wider than that needs a permit in every state on the route.

Weight: payload and gross weight
A standard step deck carries about 43,000 to 48,000 lb of freight, depending on the tractor and trailer weights. The tool defaults to 46,000 lb of payload capacity: enter your own figure from your scale ticket for an exact check.
Gross weight caps at 80,000 lb on the Interstate under 23 CFR 658.17. Enter your tractor and trailer tare weights and the tool checks your gross weight against that limit. The example machine takes 82.6 percent of the 46,000 lb payload and grosses 69,000 lb with standard tares, leaving 11,000 lb spare.

Axle weights still matter: a legal gross weight can hide an overweight tandem. Run your axle groups through the Bridge Formula Axle Weight Checker linked below.
License: a Class A CDL
Step deck work needs a Class A CDL. A combination vehicle with a gross combination weight rating of 26,001 lb or more, with the towed unit over 10,000 lb, is a Group A vehicle under 49 CFR 383.91(a)(1). A standard step deck rig clears both numbers.

What the rate math covers
Enter your loaded miles, deadhead miles, rate per loaded mile, diesel price and MPG to see the money side of the load. The tool shows gross revenue, fuel cost, net per loaded mile, net per total mile and the deadhead share of your miles.
As an example only, take 500 loaded miles plus 100 deadhead miles at a $3.50 rate, $5.00 diesel and 6.5 MPG. The load grosses $1,750.00 and burns 92.3 gallons of fuel for $461.54, leaving $1,288.46 after fuel: $2.58 per loaded mile and $2.15 per total mile, with deadhead at 16.7 percent of miles.
The tool carries no rate or diesel figure of its own: both are your numbers. Fuel is the only cost it counts, so your true cost per mile runs higher once maintenance, insurance and fixed costs join in.
How to use this calculator
Five steps and one result. No account and no email needed.
- Measure your freight: length, width, height and weight.
- Check the deck sizes against your own trailer, or keep the standard defaults.
- Enter your tare weights to see the gross weight check.
- Read the verdict: which deck fits and which limit binds.
- Enter your miles, rate, diesel price and MPG to see the rate math.
Step deck fit questions
What size freight fits on a step deck?
The lower deck takes freight up to about 10 ft high and 40 ft long on a standard trailer. The upper deck takes freight up to 8 ft 6 in high and 11 ft long. Width caps at 102 inches on either deck.
Why does my load fit the lower deck but not the upper deck?
The upper deck sits about 60 inches off the ground, so freight over 8 ft 6 in tall tops the 162 inch limit there. The lower deck sits about 39 inches high, which leaves room for freight up to about 10 ft tall. Length matters too: the upper deck runs only 11 ft against 40 ft below.
Is 13 feet 6 inches a federal height limit?
No. There is no federal height limit: states set their own, from 13 ft 6 in to 14 ft 6 in. The tool defaults to 162 inches because 13 ft 6 in is the common state limit, but you can raise it for a route that allows more.
How much weight can a step deck carry?
A standard step deck carries about 43,000 to 48,000 lb of freight within the 80,000 lb gross limit. The exact figure depends on your tractor and trailer tare weights. Enter your own payload capacity from your scale ticket for an exact check.
Can I use this for a stretch step deck?
Yes. Enter your own deck lengths in the trailer boxes: the tool checks any deck size you give it. The standard defaults suit a 48 to 53 ft trailer.
Do I need a Class A CDL to pull a step deck?
Yes. A step deck rig is a Group A combination vehicle, with a gross combination weight rating over 26,001 lb and a towed unit over 10,000 lb. That combination needs a Class A CDL under 49 CFR 383.91.
Related tools and guides
- Bridge Formula Axle Weight Checker: check any axle group against the bridge formula with your own spacings
- Hotshot Axle Weight Checker: check a hotshot load against ratings based axle limits
- Oversize Cost Calculator: work out the cost of moving a load that tops the legal size limits
- Tanker Load Calculator: work out tanker load weight, axle weights and the most you can legally load
- Cost Per Mile Calculator: put maintenance and repair costs beside fuel and insurance in your full cost per mile
- All Trucking Mind tools: free calculators and checkers for drivers and carriers
This calculator follows the width rule in 23 CFR 658.15, the weight limits in 23 CFR 658.17 and the vehicle group definitions in 49 CFR 383.91. It is guidance only.
Weight limits and size rules change. Confirm your figures with the current rule text before you rely on a single number.
Your inputs stay in your browser. Nothing is sent to our servers.