Skip to main content

Trucking Mind

Trucking Mind – Free Tool

CDL Practice Tests 2027

Original practice questions for the four CDL knowledge tests this site did not cover yet: Air Brakes, Combination Vehicles, Passenger and School Bus. Pick a test, choose a mode, then see exactly where you stand.

100% free No sign-up Pass mark 80% Question bank loading Every question checked against the official CDL manual Reviewed Nov 2026
1Pick a testAir Brakes, Combination Vehicles, Passenger or School Bus. Each one has its own question bank.
2Answer the questionsPractice with instant help, or sit a full exam-style set.
3See your scoreInstant result against the real 80% pass mark, with every miss explained.

1 – Choose your test

2 – Choose how you want to practice

Question 1 of 2500:00

0%
PASS

This is a practice result. It is a guide to your readiness, not a guarantee of passing the real test. The real exam draws from a much larger question bank.

Your score by topic, weakest first

Questions you missed, review these

Disclaimer: This is a free practice aid built from original questions based on the official state CDL manuals. It is not the actual exam. It is not an ELDT course. It does not replace training with an FMCSA-registered provider — always confirm the rules in the current CDL manual for your state. Trucking Mind is not affiliated with FMCSA or any state DMV.

Quick answer: This page carries free CDL practice tests for the four knowledge tests most drivers still need after General Knowledge: Air Brakes (25 questions on the real test), Combination Vehicles (20), Passenger (20) and School Bus (20). Every test needs 80% to pass under 49 CFR 383.135(a)(1), so you can miss 5 questions on Air Brakes and 4 on each of the other three. Each test here has two modes. Practice Mode gives instant feedback with an explanation after every question. Exam Mode copies the real test setup: a full set of questions, no feedback until the end, with a pass or fail verdict at the 80% mark.

Last reviewed: – Focus keyword: CDL air brakes practice test

What do the four CDL practice tests on this page cover?

This page carries four practice tests for the CDL knowledge areas that sit beyond General Knowledge. Air Brakes covers the air brake systems fitted to most commercial trucks and buses. Combination Vehicles covers the tractor-trailer knowledge every Class A applicant must show. Passenger covers the P endorsement for buses that carry 16 or more passengers, including the driver. School Bus covers the S endorsement for school buses, which sits on top of the P endorsement.

Each test draws on the same material the real exam draws on: the official state CDL manual, which follows the AAMVA model manual. Air Brakes questions come from Section 5 of the manual. Combination Vehicles questions come from Section 6. Passenger questions come from Section 4. School Bus questions come from Section 10. Every question states the manual section in its explanation, so a wrong answer tells you exactly where to re-read. Your state manual may number the same sections slightly differently, but the topic names and the facts are the same.

The four tests fill the gap in the practice tests already on this site. The main CDL Practice Test covers General Knowledge plus the Hazmat, Tanker and Doubles-Triples endorsements. Nothing on the site covered Air Brakes, Combination Vehicles, Passenger or School Bus until this page. Between the two pages, every CDL knowledge test now has a free practice set.

If you are not sure which class of CDL you need, or which endorsements your vehicle calls for, check before you start studying. The CDL Class Checker works out whether you need a Class A, B or C license from your vehicle weights and passenger count. The CDL Endorsement Checker works out which endorsements your vehicle and load require. Study the tests that match your license, not every test on the page.

How many questions are on the real air brakes test?

The real air brakes knowledge test has 25 questions in most states. You must answer at least 20 correctly to pass. That is the 80% pass mark the federal rule sets for every CDL knowledge test in 49 CFR 383.135(a)(1). The count comes from the AAMVA model test that most state driver license agencies follow. It is the count the Connecticut DMV, Washington DOL and Hawaii HDOT publish for their own tests.

Question counts are set by the states, not by the federal rule. The federal rule fixes the pass mark at 80% and leaves the number of questions to each state. Most states use the model counts, but a few differ. Pennsylvania, for example, uses 25 questions for its school bus test where most states use 20. Check your own state CDL manual for the exact count before you sit the real test. The 80% pass mark does not change from state to state.

Exam Mode on this page copies the real setup for each test: 25 questions for Air Brakes, 20 for Combination Vehicles, 20 for Passenger and 20 for School Bus. Practice Mode runs the full question bank for the test you picked, so you can work through every question with instant feedback. The bank holds 40 Air Brakes questions, 30 Combination Vehicles questions, 30 Passenger questions and 30 School Bus questions, 130 in total.

How many questions can you miss on each CDL test?

You can miss up to 20% of the questions on any CDL knowledge test. The table below gives the count for each test on this page, plus the tests on the main practice test page, using the model counts most states follow.

TestQuestionsCorrect to passYou can miss
Air Brakes25205
Combination Vehicles20164
Passenger (P)20164
School Bus (S)20164
General Knowledge504010
Hazmat (H)30246
Tanker (N)20164
Doubles-Triples (T)20164

Two points in the table deserve attention. First, each test is scored on its own. Passing General Knowledge does not help you on Air Brakes. Failing one endorsement test does not fail the others. Second, the miss allowance is small. On a 20-question test, five wrong answers is a fail. That is why the result screen on this page shows how many more correct answers you needed: on a short test, one or two questions decide the outcome.

Do not aim for the pass mark. Aim for the exam-ready range, 90% or better on a fresh set. The real test draws different questions from the same manual sections, so a bare 80% in practice can turn into a fail on test day. The result screen flags the 90% range separately for that reason.

What happens if you fail the air brakes test?

If you fail the air brake portion of the knowledge test, the state must put an air brake restriction on your CLP or CDL. Section 383.135(a)(2) states the rule. The restriction is code L on the license. It bars you from driving any commercial vehicle equipped with air brakes. Since most commercial trucks and buses use air brakes, an L restriction closes most driving jobs until you clear it.

The same restriction applies if you take the skills test in a vehicle with no air brake system at all. Section 383.135(b)(3) covers that case. If you test in a vehicle with air-over-hydraulic brakes, you get the Z restriction instead, which bars you from driving a vehicle with a full air brake system. Section 383.135(b)(4) covers that case. The CDL Restriction Decoder explains every restriction code on a CDL and what it takes to remove each one.

Removing the L restriction does not mean retaking the whole skills test. Section 383.135(b)(7) lets the state run a modified skills test instead. You must also pass the air brake pre-trip inspection and pass the air brake knowledge test. That is the whole point of the Air Brakes practice test on this page: the knowledge test is the part you can prepare for at home. It is also the part that decides whether the restriction lands on your license.

What happens if you fail the combination vehicles test?

Failing the combination vehicles test is a hard stop for a Class A applicant. Section 383.135(a)(3) says a driver who fails the combination vehicle portion of the knowledge test must not be issued a Group A CLP or CDL. There is no restricted Class A license to fall back on. You retake the test and pass it, or you do not get the Class A.

The combination test is short: 20 questions, 16 to pass. The content is narrow too. Section 383.111(c) lists only three knowledge areas for combination vehicles: coupling and uncoupling, vehicle inspection for combinations plus general operating practices including air brakes. A driver who studies those three areas in Section 6 of the manual has covered the whole test. The practice set here mirrors that split, with questions on coupling, uncoupling, inspection, combination air brakes, rollover, jackknife and space management.

Class B and Class C applicants do not take the combination test at all. It exists only for Group A, the tractor-trailer license. If your vehicle is a straight truck or a bus, your time is better spent on Air Brakes and on the endorsement tests for your vehicle. The CDL Class Checker settles which class your vehicle needs before you pick a test to study.

Do the passenger and school bus endorsements need a skills test too?

Yes. The P and S endorsements are the only endorsements that need both a knowledge test and a skills test. Section 383.93(c) sets the testing for each endorsement: Double-Triple, Tank Vehicle and Hazmat need a knowledge test only, while Passenger and School Bus need a knowledge test and a skills test. The skills test must be taken in a vehicle of the same group you will drive. For the S endorsement it must be taken in a school bus.

The S endorsement has one more condition. Section 383.123(a)(1) requires you to qualify for the passenger endorsement first. You pass the P knowledge test and the P skills test, then you take the S knowledge test and a skills test in a school bus. There is no route to an S endorsement that skips the P endorsement. Study Section 4 of the manual for the P test, then Section 10 for the S test, in that order.

Both endorsements also need Entry-Level Driver Training before the first issue. Section 380.609 requires ELDT for a first P or S endorsement, with theory plus behind-the-wheel training. The ELDT Requirement Checker works out whether ELDT applies to you and which curriculum it means. Practice tests help you pass the knowledge test. They do not replace ELDT. They do not count toward it.

What should you study for the air brakes test?

Section 383.111(b) lists the seven knowledge areas every driver of an air-braked vehicle must know. The real test draws from these seven areas. So does the practice bank here.

First, general air brake system nomenclature: the parts and what they do, from the compressor and governor to the storage tanks, brake chambers, slack adjusters and foundation brakes. Second, the dangers of a contaminated air supply: dirt, moisture and oil in the system. Third, what happens when air lines between the power unit and the trailer are severed or disconnected. Fourth, what low air pressure readings mean.

Fifth, pre-trip inspection procedures for air brakes, including the automatic fail-safe devices, the system monitoring devices and the low pressure warning alarms. Sixth, en route and post-trip inspection procedures, including the air loss tests with the engine running and with it off, plus the pressure levels where the low air warning and the tractor protection valve activate. Seventh, general operating practices: proper braking technique, antilock brakes, emergency stops and the parking brake.

The numbers in Section 5 of the manual are the facts the test checks most often. The governor cuts in at about 100 psi and cuts out between 120 and 140 psi. The low air warning must come on before pressure drops to 60 psi. Spring brakes apply at 20 to 45 psi. So does the tractor protection valve. The safety valve opens at 150 psi. Air loss must stay under 2 psi per minute for a single vehicle and under 3 psi for a combination with the brakes released, plus under 3 and 4 psi with the brakes applied. Pressure must build from 85 to 100 psi within 45 seconds. Learn those figures and the test gets much easier.

What should you study for the combination vehicles test?

Section 383.111(c) lists three knowledge areas for combination vehicles. The first is coupling and uncoupling: the procedures for connecting and disconnecting a tractor and a semi-trailer. The second is vehicle inspection: the objectives and procedures that are unique to combination vehicles, with the coupling area at the center. The third is general operating practices and procedures, including safely operating combination vehicles and their air brakes.

Coupling questions turn on a short sequence. Check the fifth wheel and the kingpin. Line the tractor up and back slowly under the trailer, which should sit slightly lower than the center of the fifth wheel. Lock the jaws around the shank of the kingpin, not the head. Test the lock with a gentle pull against the trailer brakes. Check that there is no space between the upper and lower fifth wheel. Connect the air lines and the electrical cable, charge the system, then test the trailer brakes. Uncoupling reverses the order: chock the wheels, lower the landing gear, disconnect the lines, unlock the fifth wheel and pull forward slowly.

Operating questions turn on two risks that only combinations have: rollover and jackknife. Rollover comes from speed on curves and ramps and from a high or off-center load. Jackknife comes from locking the drive wheels under braking while the trailer keeps pushing. The recovery in both cases starts with easing off the brakes and letting the wheels roll. The practice set here gives both topics their own score line, so you can see which one needs more work.

What should you study for the passenger and school bus tests?

The passenger test draws on Section 4 of the manual, Transporting Passengers Safely. The topics are vehicle inspection for buses, loading and unloading passengers, driving with passengers aboard, after-trip inspection plus prohibited practices. The facts the test checks most often are the railroad crossing stop, 15 to 50 feet before the nearest rail, the drawbridge stop, at least 50 feet before the draw, the standee line plus the hazardous materials limits: most hazardous materials are forbidden on a bus. The allowed kinds together must not pass 100 pounds.

The school bus test draws on Section 10 of the manual and on the four topics Section 383.123(a)(2) names: loading and unloading children, including the stop signal devices, mirrors, flashing lights and other warning devices; emergency exits and evacuation procedures; state and federal laws for railroad-highway grade crossings; and operating practices not otherwise specified. The numbers to learn are the 10-foot danger zone around the bus, the amber lights 100 to 500 feet before a stop, the railroad stop 15 to 50 feet before the nearest rail, plus the 100-foot evacuation distance.

Both tests reward careful reading of the manual more than general driving sense. Several answers are exact numbers or exact procedures: the distance for the amber lights, the distance for the danger zone, the rule that a bus must stop at every railroad crossing even when the signals are clear. The practice questions here test those exact facts. Every explanation gives the manual section so you can check the source.

How does Practice Mode differ from Exam Mode?

Practice Mode is the study mode. You work through the full question bank for the test you picked. After each answer you see at once whether you were right, with a plain-English explanation and the manual section to re-read. A wrong answer locks the question and shows the correct answer, so you learn from the miss on the spot. There is no time limit. Use Practice Mode first, until the explanations stop surprising you.

Exam Mode is the rehearsal. It draws a full exam-size set at random: 25 questions for Air Brakes, 20 for each of the other three tests. You get no feedback until the end. You can move back and change an answer before you finish, as you can on the real test. Unanswered questions count as wrong. The page warns you before it scores a set with blanks. The result is a pass or fail verdict at the real 80% pass mark, with your score by topic and every miss explained.

Use the two modes in order. Practice Mode builds knowledge. Exam Mode tests whether the knowledge holds when the help is gone. A driver who scores 90% or better on two fresh Exam Mode sets in a row is ready to book. A driver who scores between 80% and 89% is passing with no margin and should study the weakest topics first. The result screen shows your weakest topics first for exactly that reason, with a study flag on every topic under 80%.

Your best score for each test is saved in your own browser, so you can watch it climb across sessions. Nothing leaves your browser. There is no account and no sign-up. Your answers are never sent to our servers.

How do you use these CDL practice tests?

Work through the tests in the order that matches your license. Start with Air Brakes if your vehicle has air brakes, then Combination Vehicles if you need a Class A, then Passenger and School Bus for the endorsements. The CDL Endorsement Checker confirms which endorsements your vehicle needs.

  1. Pick a test section: Air Brakes, Combination Vehicles, Passenger or School Bus.
  2. Choose Practice Mode for instant feedback or Exam Mode for a full exam-style set.
  3. Answer every question. In Practice Mode you see the explanation and the manual section after each answer.
  4. Use the Previous and Next buttons to move through the set. In Exam Mode you can change an answer before you finish.
  5. Read your score against the 80% pass mark, your score by topic, plus the questions you missed.
  6. Study your weakest topics in the official CDL manual, then take a fresh set.

Before you book the real test, check the rest of the process too. The CDL Disqualification Checker works out whether a conviction affects your license. The Driver Qualification Self-Check runs through the general qualifications in 49 CFR 391.11. The Road Test and Equivalent Checker works out whether you need a road test or whether an equivalent document covers you.

Frequently asked questions

How many questions are on the CDL air brakes test?

The real air brakes test has 25 questions in most states. You must answer at least 20 correctly to pass, which is the 80% pass mark in 49 CFR 383.135(a)(1). You can miss 5 questions. The count follows the AAMVA model test that most state driver license agencies use. A few states differ, so check your own state CDL manual for the exact count.

How many questions can you miss on the CDL combination test?

The combination vehicles test has 20 questions in most states. You must answer at least 16 correctly to pass. You can miss 4 questions. Failing the combination test is a hard stop for a Class A applicant: section 383.135(a)(3) says no Group A CLP or CDL may be issued to a driver who fails it.

What happens if I fail the air brakes test?

The state must put an air brake restriction, code L, on your CLP or CDL. Section 383.135(a)(2) states the rule. The restriction bars you from driving any commercial vehicle equipped with air brakes. To remove it you must pass the air brake knowledge test and the air brake pre-trip inspection, plus a modified skills test under section 383.135(b)(7).

Do I need ELDT before the passenger or school bus test?

Yes, for a first P or S endorsement. Section 380.609 requires Entry-Level Driver Training before the first passenger or school bus endorsement, with theory plus behind-the-wheel training from an FMCSA-registered provider. The training must be complete before you take the skills test. Practice tests help you pass the knowledge test. They do not replace ELDT and they do not count toward it.

Are these the actual CDL exam questions?

No. Real exam questions are not public. These are original questions written from the official state CDL manuals, covering the same knowledge areas and using the same facts the real test checks. Every question names the manual section it comes from, so you can verify each fact in the manual yourself.

What is the pass mark for CDL knowledge tests?

Every CDL knowledge test needs 80% to pass. Section 383.135(a)(1) sets the mark: a driver must correctly answer at least 80% of the questions on each knowledge test. The mark is federal, so it is the same in every state and for every test, from General Knowledge to the endorsements.

Related tools

  • CDL Practice Test: General Knowledge plus Hazmat, Tanker and Doubles-Triples practice tests, the companion to this page.
  • CDL Class Checker: works out whether you need a Class A, B or C license from your vehicle weights and passenger count.
  • CDL Endorsement Checker: works out which endorsements your vehicle and load require, plus what test each one needs.
  • ELDT Requirement Checker: works out whether Entry-Level Driver Training applies to you before you test.

Sources

Follow on WhatsApp Ask by Voice