Part 1 — The 20 percent calculator
Count every wheel-end brake with an out-of-service condition: no braking action, a broken or missing part, a loose part, an air leak at the chamber, pushrod stroke 1/4 inch or more past its limit, or lining worn below the minimum. Steering axle brakes count too.
A standard 5-axle tractor-trailer has 10: 2 on the steer axle, 4 on the drives and 4 on the trailer.
Leave 0 if every brake works and nothing is worn past its limit. At 20 percent the vehicle is out of service.
Part 2 — Air loss rate test
Fully charge the system, turn the engine off and release the parking brake. Time the pressure drop for one minute with the brakes released, then hold the foot brake down for one minute after the first drop. Chock the wheels first.
A combination allows 1 psi more loss than a single vehicle on each test, because it has more parts that can leak.
Limit: less than 2 psi for a single vehicle, less than 3 psi for a combination.
Limit: no more than 3 psi for a single vehicle, no more than 4 psi for a combination, after the first drop.
CVSA air loss rule
CVSA also fails a truck when pressure will not hold at 80 to 90 psi with the governor cut in, the engine at idle and the service brakes fully applied. A leak you can hear is already a fail.
Part 3 — Low air warning
Fan the brakes down with the engine off and watch the gauge. The warning light or buzzer must come on at 55 psi or above. Most trucks warn at 60 psi. If either the light or the buzzer works as required, the truck passes this check.
Leave blank if you have not run the test yet. Below 55 psi is out of service.
No warning at all?
A missing or dead warning device is out of service on its own. Enter 0 if the warning never comes on.
Part 4 — Walk-around checks
Grade each check honestly. Every one of these is a standalone out-of-service condition in the CVSA criteria, so one fail anywhere means an out-of-service verdict.
Fail if any hose is damaged through the outer reinforcement ply, bulges under pressure, leaks where it should not, is spliced over tubing or is crimped. On nylon tubing, a second color showing through is a fail.
Fail if either steering brake does not work, chamber sizes or slack adjuster lengths do not match across the axle, or lining is below 3/16 inch on a drum brake or 1/8 inch on an air disc brake. Cracked, loose or oil-soaked lining fails too.
Fail on any external crack that opens when the brake applies, or any part of a drum or rotor missing or about to fall away. Short hairline heat-check cracks are not a fail. Metal-to-metal contact means the lining is gone.
Set the parking brake, put the truck in a low gear and gently pull forward. The truck must not move. Check the trailer breakaway too: the trailer brakes must apply when you pull the trailer supply. Holes or cracks in a spring brake housing fail as well.
The verdict updates as you change any answer. Your entries stay in this browser. Nothing is sent to our servers. There is no account to create.
Disclaimer: This tool is provided for general information only. It is not professional advice — verify figures from official sources before acting on them. This checker is guidance, not a guarantee: it grades seven brake checks against the CVSA out-of-service criteria. The inspector at the scale makes the final call.
Quick answer: A truck fails inspection when 20 percent or more of its service brakes have an out-of-service condition. A standard 5-axle combination has 10 service brakes, so 2 defective brakes put the whole unit out of service. In CVSA Brake Safety Week 2026, inspectors placed 2,369 of 15,528 vehicles out of service for brakes. Nearly half of those, 1,176 vehicles, failed on the 20 percent rule alone. Run the seven checks above before you roll into a scale.
What inspectors failed trucks on in 2026
CVSA ran Brake Safety Week from August 23 to 29, 2026. Inspectors in 51 jurisdictions across the United States, Canada and Mexico completed 15,528 brake inspections.
They placed 2,369 vehicles out of service for brake-related violations, a 15.3 percent out-of-service rate. The other 13,159 vehicles, 84.7 percent, had no brake-related out-of-service violation.
| Violation | Count | Notes |
|---|---|---|
| 20 percent defective brake rule | 1,176 | Vehicles out of service, 49.6 percent of all brake out-of-service orders |
| Brake hoses and tubes | 600 | Out-of-service violations |
| Air loss rate | 145 | Out-of-service violations |
| Steering axle linings | 92 | Out-of-service violations |
| Other steering axle conditions | 119 | Out-of-service violations |
| Other brake violations | 759 | Includes tractor protection, air tanks, parking and emergency brakes, low-air warning, hydraulic and electric brakes |
| Drum and rotor violations (2026 focus) | 141 | Violations found, 64 vehicles out of service |
The 2026 focus was drums and rotors. The worst air-disc faults were a rusted rotor (45), broken rotors (32) and metal-to-metal contact (20). Some vehicles had more than one violation, so the counts above do not add up to the vehicle total.
The next Brake Safety Week is scheduled for April 18 to 24, 2027. Brake checks run all year, not only during the campaign week. These are campaign figures from a focused enforcement week, not a measure of every truck on the road.
The 20 percent rule, in plain English
The rule counts defective brakes against total service brakes on the vehicle or combination. A brake counts as defective when it has no effective braking action, a missing or broken part, a loose part, an audible air leak at the chamber, pushrod stroke 1/4 inch or more past its limit, or lining worn below the minimum.
Steering axle brakes count in the 20 percent total too. A single bad steering brake can also put the truck out of service on its own.
The line is exact. At 20 percent the vehicle is out of service, not at 21 percent.
| Service brakes | Most defective brakes that still pass | First count that fails |
|---|---|---|
| 4 | 0 | 1 (25.0 percent) |
| 6 | 1 | 2 (33.3 percent) |
| 8 | 1 | 2 (25.0 percent) |
| 10 | 1 | 2 (20.0 percent) |
| 12 | 2 | 3 (25.0 percent) |
| 14 | 2 | 3 (21.4 percent) |
| 18 | 3 | 4 (22.2 percent) |
A standard 5-axle tractor-trailer has 10 service brakes: 2 on the steer axle, 4 on the drive axles and 4 on the trailer axles. Two defective brakes anywhere in that set put the whole combination out of service.
Pushrod stroke has its own counting rule. One brake 1/4 inch or more past its adjustment limit counts as one defective brake. Two brakes each less than 1/4 inch past the limit also count as one defective brake. A brake sitting exactly at its limit is not a violation. For a standard Type 30 clamp chamber the limit is 2 inches, so a pushrod at 2-1/4 inches is one defective brake.
The seven checks: what the inspector looks for
Each check below is a standalone out-of-service condition in the CVSA criteria, except the 20 percent rule, which is the count across the whole vehicle. One fail anywhere is enough to park the truck.
| Check | What fails it | Source |
|---|---|---|
| 20 percent rule | Defective brakes at or above 20 percent of service brakes on the vehicle or combination | CVSA Part II item 1.a |
| Air loss rate | Static loss above 2 psi (single vehicle) or 3 psi (combination) in one minute; applied loss above 3 psi (single vehicle) or 4 psi (combination); or pressure that will not hold at 80 to 90 psi with the engine at idle and the brakes applied | Model CDL Manual Section 5; CVSA Part II item 1 |
| Hoses and tubes | Damage through the outer reinforcement ply; bulge or swelling under pressure; audible leak away from a fitting; improper splice; crimped hose that restricts air flow | CVSA Part II item 1 |
| Steering axle | Either steering brake inoperative; mismatched chamber sizes or slack adjuster lengths; lining below 3/16 inch (drum brake, continuous strip), 1/4 inch (drum brake, two pads) or 1/8 inch (air disc brake); cracked, loose or oil-soaked lining | CVSA Part II item 1.b; 49 CFR 393.47 |
| Drums and rotors | External crack that opens on application; any part missing or about to fall away | CVSA Part II item 1 |
| Parking and emergency brake | Parking brake that does not hold in a low-gear tug test; trailer breakaway that does not apply; holes or cracks in a spring brake housing | Model CDL Manual Section 2; CVSA Part II item 1 |
| Low air warning | Warning missing or inoperative, or silent until pressure falls below 55 psi | CVSA Part II item 1; 49 CFR 393.51 |
Two details catch drivers out. A brake sitting exactly at its adjustment limit is not a violation. A low-air warning passes when either the light or the buzzer works as required. Both points are written into the criteria.
Braking performance is a separate standard. Federal rules require a braking force of at least 43.5 percent of gross weight for most property-carrying vehicles, measured on a performance-based brake tester. A driver cannot self-test that number at the roadside, so it is not one of the seven checks here.
How to use this checker
Five steps, about ten minutes with the truck. Do the air tests with the wheels choked.
- Count your service brakes and enter how many are defective, or leave 0 if none are.
- Run the static and applied air loss tests and enter both readings.
- Fan the brakes down and enter the pressure where the low-air warning comes on.
- Walk the truck, grade the four walk-around checks and press Check my brakes.
- Read the verdict, fix every failed item and copy the result for your shop or your file.
Brake inspection questions
How many bad brakes put a truck out of service?
A vehicle or combination goes out of service when 20 percent or more of its service brakes have an out-of-service condition. A standard 5-axle combination has 10 service brakes, so 2 defective brakes are enough. A single vehicle with 4 service brakes fails on 1 defective brake. Steering axle brakes count in the total too.
What is the air loss limit for a combination vehicle?
With the engine off and the brakes released, a combination vehicle must lose less than 3 psi in one minute. With the foot brake fully applied, it must lose no more than 4 psi in one minute after the first drop. A single vehicle must lose less than 2 psi with the brakes released and no more than 3 psi with the brakes applied. CVSA also fails a truck when pressure will not hold at 80 to 90 psi with the engine at idle and the brakes fully applied.
At what pressure must the low-air warning come on?
The warning must operate at 55 psi and below, or at one half of the governor cut-out pressure, whichever is less. In practice the warning must already be on by the time pressure falls to 55 psi. Most trucks warn at 60 psi under the federal safety standard for new vehicles. If either the warning light or the buzzer works as required, the truck passes this check.
How thick must steering axle brake linings be?
On a steering axle air drum brake, lining must be at least 3/16 inch thick at the shoe center for a shoe with a continuous strip of lining, or at least 1/4 inch for a shoe with two pads. Air disc brake pads on the steering axle must be at least 1/8 inch thick. On non-steering axles the minimum is 1/4 inch for drum brakes and 1/8 inch for disc brakes. Lining worn to its wear indicator fails at any thickness.
What brake problems fail the most trucks?
In CVSA Brake Safety Week 2026, the 20 percent defective brake rule put 1,176 vehicles out of service, almost half of all brake out-of-service orders. Brake hoses and tubes drew 600 out-of-service violations. Air loss rate drew 145. Steering axle linings drew 92 and other steering axle conditions drew 119. Drums and rotors drew 141 violations and 64 out-of-service orders.
Does a pass here guarantee I pass inspection?
No. This checker grades seven brake checks against the CVSA out-of-service criteria and the federal brake rules. A Level I inspection covers the whole vehicle and the driver. The inspector at the scale makes the final call. Use this checker to find and fix problems before you roll in, not as a promise of a clean inspection.
Related tools and guides
- CSA Violation Points Checker — check how a brake violation counts against your CSA score and when it falls off
- Truck Photo Diagnostic — photograph a brake, hose or drum you are unsure about and get a plain-English read on what is wrong
- Maintenance Reserve Calculator — work out the yearly maintenance fund for your truck, so brake work never waits for cash
- All Trucking Mind tools — free calculators and checkers for drivers and carriers
This checker grades seven brake checks against the CVSA North American Standard Out-of-Service Criteria, 49 CFR 393.41, 393.47, 393.51 and 393.52 and the Model CDL Manual. It is guidance, not a guarantee: the inspector at the scale makes the final call. Confirm any figure against the source before you act on it.
Your entries stay in your browser. Nothing is sent to our servers.
By Mike Archer — Last reviewed: November 2026
Why use this brake inspection readiness checker
This brake inspection readiness checker grades the same seven checks an inspector uses, so a driver can find a failed hose, a worn lining or a dead low-air warning in the yard instead of at a scale. Pair it with the CSA Violation Points Checker to see how a brake violation counts against your CSA score, and with the Maintenance Reserve Calculator to set aside the money for the brake work it finds.